e1000phyreg.h revision 193291
138032Speter/* $FreeBSD: head/sys/dev/mii/e1000phyreg.h 193291 2009-06-02 00:30:30Z yongari $ */ 238032Speter/*- 338032Speter * Principal Author: Parag Patel 438032Speter * Copyright (c) 2001 538032Speter * All rights reserved. 638032Speter * 738032Speter * Redistribution and use in source and binary forms, with or without 838032Speter * modification, are permitted provided that the following conditions 938032Speter * are met: 1038032Speter * 1. Redistributions of source code must retain the above copyright 1138032Speter * notice unmodified, this list of conditions, and the following 1238032Speter * disclaimer. 1338032Speter * 2. Redistributions in binary form must reproduce the above copyright 1438032Speter * notice, this list of conditions and the following disclaimer in the 1542575Speter * documentation and/or other materials provided with the distribution. 1638032Speter * 1738032Speter * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 1842575Speter * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 1942575Speter * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 2038032Speter * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 2138032Speter * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 2238032Speter * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 2338032Speter * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 2438032Speter * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 2538032Speter * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 2638032Speter * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 2738032Speter * SUCH DAMAGE. 2838032Speter * 2938032Speter * Additonal Copyright (c) 2001 by Traakan Software under same licence. 3038032Speter * Secondary Author: Matthew Jacob 3138032Speter */ 3238032Speter 3338032Speter/*- 3438032Speter * Derived by information released by Intel under the following license: 3538032Speter * 3638032Speter * Copyright (c) 1999 - 2001, Intel Corporation 3738032Speter * 3838032Speter * All rights reserved. 3938032Speter * 4038032Speter * Redistribution and use in source and binary forms, with or without 4138032Speter * modification, are permitted provided that the following conditions are met: 4238032Speter * 4338032Speter * 1. Redistributions of source code must retain the above copyright notice, 4438032Speter * this list of conditions and the following disclaimer. 4538032Speter * 4638032Speter * 2. Redistributions in binary form must reproduce the above copyright notice, 4738032Speter * this list of conditions and the following disclaimer in the 4838032Speter * documentation and/or other materials provided with the distribution. 49 * 50 * 3. Neither the name of Intel Corporation nor the names of its contributors 51 * may be used to endorse or promote products derived from this software 52 * without specific prior written permission. 53 * 54 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' 55 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 56 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 57 * ARE DISCLAIMED. IN NO EVENT SHALL CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 58 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 59 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 60 * LOSS OF USE, DATA, OR * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND 61 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 62 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 63 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 64 * 65 */ 66 67/* 68 * Marvell E1000 PHY registers 69 */ 70 71#define E1000_MAX_REG_ADDRESS 0x1F 72 73#define E1000_CR 0x00 /* control register */ 74#define E1000_CR_SPEED_SELECT_MSB 0x0040 75#define E1000_CR_COLL_TEST_ENABLE 0x0080 76#define E1000_CR_FULL_DUPLEX 0x0100 77#define E1000_CR_RESTART_AUTO_NEG 0x0200 78#define E1000_CR_ISOLATE 0x0400 79#define E1000_CR_POWER_DOWN 0x0800 80#define E1000_CR_AUTO_NEG_ENABLE 0x1000 81#define E1000_CR_SPEED_SELECT_LSB 0x2000 82#define E1000_CR_LOOPBACK 0x4000 83#define E1000_CR_RESET 0x8000 84 85#define E1000_CR_SPEED_1000 0x0040 86#define E1000_CR_SPEED_100 0x2000 87#define E1000_CR_SPEED_10 0x0000 88 89#define E1000_SR 0x01 /* status register */ 90#define E1000_SR_EXTENDED 0x0001 91#define E1000_SR_JABBER_DETECT 0x0002 92#define E1000_SR_LINK_STATUS 0x0004 93#define E1000_SR_AUTO_NEG 0x0008 94#define E1000_SR_REMOTE_FAULT 0x0010 95#define E1000_SR_AUTO_NEG_COMPLETE 0x0020 96#define E1000_SR_PREAMBLE_SUPPRESS 0x0040 97#define E1000_SR_EXTENDED_STATUS 0x0100 98#define E1000_SR_100T2 0x0200 99#define E1000_SR_100T2_FD 0x0400 100#define E1000_SR_10T 0x0800 101#define E1000_SR_10T_FD 0x1000 102#define E1000_SR_100TX 0x2000 103#define E1000_SR_100TX_FD 0x4000 104#define E1000_SR_100T4 0x8000 105 106#define E1000_ID1 0x02 /* ID register 1 */ 107#define E1000_ID2 0x03 /* ID register 2 */ 108#define E1000_ID_88E1000 0x01410C50 109#define E1000_ID_88E1000S 0x01410C40 110#define E1000_ID_88E1011 0x01410C20 111#define E1000_ID_MASK 0xFFFFFFF0 112 113#define E1000_AR 0x04 /* autonegotiation advertise reg */ 114#define E1000_AR_SELECTOR_FIELD 0x0001 115#define E1000_AR_10T 0x0020 116#define E1000_AR_10T_FD 0x0040 117#define E1000_AR_100TX 0x0080 118#define E1000_AR_100TX_FD 0x0100 119#define E1000_AR_100T4 0x0200 120#define E1000_AR_PAUSE 0x0400 121#define E1000_AR_ASM_DIR 0x0800 122#define E1000_AR_REMOTE_FAULT 0x2000 123#define E1000_AR_NEXT_PAGE 0x8000 124#define E1000_AR_SPEED_MASK 0x01E0 125 126/* Autonegotiation register bits for fiber cards (Alaska Only!) */ 127#define E1000_FA_1000X_FD 0x0020 128#define E1000_FA_1000X 0x0040 129#define E1000_FA_SYM_PAUSE 0x0080 130#define E1000_FA_ASYM_PAUSE 0x0100 131#define E1000_FA_FAULT1 0x1000 132#define E1000_FA_FAULT2 0x2000 133#define E1000_FA_NEXT_PAGE 0x8000 134 135#define E1000_LPAR 0x05 /* autoneg link partner abilities reg */ 136#define E1000_LPAR_SELECTOR_FIELD 0x0001 137#define E1000_LPAR_10T 0x0020 138#define E1000_LPAR_10T_FD 0x0040 139#define E1000_LPAR_100TX 0x0080 140#define E1000_LPAR_100TX_FD 0x0100 141#define E1000_LPAR_100T4 0x0200 142#define E1000_LPAR_PAUSE 0x0400 143#define E1000_LPAR_ASM_DIR 0x0800 144#define E1000_LPAR_REMOTE_FAULT 0x2000 145#define E1000_LPAR_ACKNOWLEDGE 0x4000 146#define E1000_LPAR_NEXT_PAGE 0x8000 147 148/* autoneg link partner ability register bits for fiber cards (Alaska Only!) */ 149#define E1000_FPAR_1000X_FD 0x0020 150#define E1000_FPAR_1000X 0x0040 151#define E1000_FPAR_SYM_PAUSE 0x0080 152#define E1000_FPAR_ASYM_PAUSE 0x0100 153#define E1000_FPAR_FAULT1 0x1000 154#define E1000_FPAR_FAULT2 0x2000 155#define E1000_FPAR_ACK 0x4000 156#define E1000_FPAR_NEXT_PAGE 0x8000 157 158#define E1000_ER 0x06 /* autoneg expansion reg */ 159#define E1000_ER_LP_NWAY 0x0001 160#define E1000_ER_PAGE_RXD 0x0002 161#define E1000_ER_NEXT_PAGE 0x0004 162#define E1000_ER_LP_NEXT_PAGE 0x0008 163#define E1000_ER_PAR_DETECT_FAULT 0x0100 164 165#define E1000_NPTX 0x07 /* autoneg next page TX */ 166#define E1000_NPTX_MSG_CODE_FIELD 0x0001 167#define E1000_NPTX_TOGGLE 0x0800 168#define E1000_NPTX_ACKNOWLDGE2 0x1000 169#define E1000_NPTX_MSG_PAGE 0x2000 170#define E1000_NPTX_NEXT_PAGE 0x8000 171 172#define E1000_RNPR 0x08 /* autoneg link-partner (?) next page */ 173#define E1000_RNPR_MSG_CODE_FIELD 0x0001 174#define E1000_RNPR_TOGGLE 0x0800 175#define E1000_RNPR_ACKNOWLDGE2 0x1000 176#define E1000_RNPR_MSG_PAGE 0x2000 177#define E1000_RNPR_ACKNOWLDGE 0x4000 178#define E1000_RNPR_NEXT_PAGE 0x8000 179 180#define E1000_1GCR 0x09 /* 1000T (1G) control reg */ 181#define E1000_1GCR_ASYM_PAUSE 0x0080 182#define E1000_1GCR_1000T 0x0100 183#define E1000_1GCR_1000T_FD 0x0200 184#define E1000_1GCR_REPEATER_DTE 0x0400 185#define E1000_1GCR_MS_VALUE 0x0800 186#define E1000_1GCR_MS_ENABLE 0x1000 187#define E1000_1GCR_TEST_MODE_NORMAL 0x0000 188#define E1000_1GCR_TEST_MODE_1 0x2000 189#define E1000_1GCR_TEST_MODE_2 0x4000 190#define E1000_1GCR_TEST_MODE_3 0x6000 191#define E1000_1GCR_TEST_MODE_4 0x8000 192#define E1000_1GCR_SPEED_MASK 0x0300 193 194#define E1000_1GSR 0x0A /* 1000T (1G) status reg */ 195#define E1000_1GSR_IDLE_ERROR_CNT 0x0000 196#define E1000_1GSR_ASYM_PAUSE_DIR 0x0100 197#define E1000_1GSR_LP 0x0400 198#define E1000_1GSR_LP_FD 0x0800 199#define E1000_1GSR_REMOTE_RX_STATUS 0x1000 200#define E1000_1GSR_LOCAL_RX_STATUS 0x2000 201#define E1000_1GSR_MS_CONFIG_RES 0x4000 202#define E1000_1GSR_MS_CONFIG_FAULT 0x8000 203 204#define E1000_ESR 0x0F /* IEEE extended status reg */ 205#define E1000_ESR_1000T 0x1000 206#define E1000_ESR_1000T_FD 0x2000 207#define E1000_ESR_1000X 0x4000 208#define E1000_ESR_1000X_FD 0x8000 209 210#define E1000_TX_POLARITY_MASK 0x0100 211#define E1000_TX_NORMAL_POLARITY 0 212 213#define E1000_AUTO_POLARITY_DISABLE 0x0010 214 215#define E1000_SCR 0x10 /* special control register */ 216#define E1000_SCR_JABBER_DISABLE 0x0001 217#define E1000_SCR_POLARITY_REVERSAL 0x0002 218#define E1000_SCR_SQE_TEST 0x0004 219#define E1000_SCR_INT_FIFO_DISABLE 0x0008 220#define E1000_SCR_CLK125_DISABLE 0x0010 221#define E1000_SCR_MDI_MANUAL_MODE 0x0000 222#define E1000_SCR_MDIX_MANUAL_MODE 0x0020 223#define E1000_SCR_AUTO_X_1000T 0x0040 224#define E1000_SCR_AUTO_X_MODE 0x0060 225#define E1000_SCR_10BT_EXT_ENABLE 0x0080 226#define E1000_SCR_MII_5BIT_ENABLE 0x0100 227#define E1000_SCR_SCRAMBLER_DISABLE 0x0200 228#define E1000_SCR_FORCE_LINK_GOOD 0x0400 229#define E1000_SCR_ASSERT_CRS_ON_TX 0x0800 230#define E1000_SCR_RX_FIFO_DEPTH_6 0x0000 231#define E1000_SCR_RX_FIFO_DEPTH_8 0x1000 232#define E1000_SCR_RX_FIFO_DEPTH_10 0x2000 233#define E1000_SCR_RX_FIFO_DEPTH_12 0x3000 234#define E1000_SCR_TX_FIFO_DEPTH_6 0x0000 235#define E1000_SCR_TX_FIFO_DEPTH_8 0x4000 236#define E1000_SCR_TX_FIFO_DEPTH_10 0x8000 237#define E1000_SCR_TX_FIFO_DEPTH_12 0xC000 238 239/* 88E3016 only */ 240#define E1000_SCR_AUTO_MDIX 0x0030 241#define E1000_SCR_SIGDET_POLARITY 0x0040 242#define E1000_SCR_EXT_DISTANCE 0x0080 243#define E1000_SCR_FEFI_DISABLE 0x0100 244#define E1000_SCR_NLP_GEN_DISABLE 0x0800 245#define E1000_SCR_LPNP 0x1000 246#define E1000_SCR_NLP_CHK_DISABLE 0x2000 247#define E1000_SCR_EN_DETECT 0x4000 248 249#define E1000_SCR_EN_DETECT_MASK 0x0300 250 251/* 88E1112 page 2 */ 252#define E1000_SCR_MODE_MASK 0x0380 253#define E1000_SCR_MODE_AUTO 0x0180 254#define E1000_SCR_MODE_COPPER 0x0280 255#define E1000_SCR_MODE_1000BX 0x0380 256 257/* 88E1116 page 0 */ 258#define E1000_SCR_POWER_DOWN 0x0004 259/* 88E1116, 88E1149 page 2 */ 260#define E1000_SCR_RGMII_POWER_UP 0x0008 261 262/* 88E1116, 88E1149 page 3 */ 263#define E1000_SCR_LED_STAT0_MASK 0x000F 264#define E1000_SCR_LED_STAT1_MASK 0x00F0 265#define E1000_SCR_LED_INIT_MASK 0x0F00 266#define E1000_SCR_LED_LOS_MASK 0xF000 267#define E1000_SCR_LED_STAT0(x) ((x) & E1000_SCR_LED_STAT0_MASK) 268#define E1000_SCR_LED_STAT1(x) ((x) & E1000_SCR_LED_STAT1_MASK) 269#define E1000_SCR_LED_INIT(x) ((x) & E1000_SCR_LED_INIT_MASK) 270#define E1000_SCR_LED_LOS(x) ((x) & E1000_SCR_LED_LOS_MASK) 271 272#define E1000_SSR 0x11 /* special status register */ 273#define E1000_SSR_JABBER 0x0001 274#define E1000_SSR_REV_POLARITY 0x0002 275#define E1000_SSR_MDIX 0x0020 276#define E1000_SSR_LINK 0x0400 277#define E1000_SSR_SPD_DPLX_RESOLVED 0x0800 278#define E1000_SSR_PAGE_RCVD 0x1000 279#define E1000_SSR_DUPLEX 0x2000 280#define E1000_SSR_SPEED 0xC000 281#define E1000_SSR_10MBS 0x0000 282#define E1000_SSR_100MBS 0x4000 283#define E1000_SSR_1000MBS 0x8000 284 285#define E1000_IER 0x12 /* interrupt enable reg */ 286#define E1000_IER_JABBER 0x0001 287#define E1000_IER_POLARITY_CHANGE 0x0002 288#define E1000_IER_MDIX_CHANGE 0x0040 289#define E1000_IER_FIFO_OVER_UNDERUN 0x0080 290#define E1000_IER_FALSE_CARRIER 0x0100 291#define E1000_IER_SYMBOL_ERROR 0x0200 292#define E1000_IER_LINK_STAT_CHANGE 0x0400 293#define E1000_IER_AUTO_NEG_COMPLETE 0x0800 294#define E1000_IER_PAGE_RECEIVED 0x1000 295#define E1000_IER_DUPLEX_CHANGED 0x2000 296#define E1000_IER_SPEED_CHANGED 0x4000 297#define E1000_IER_AUTO_NEG_ERR 0x8000 298 299/* 88E1116, 88E1149 page 3, LED timer control. */ 300#define E1000_PULSE_MASK 0x7000 301#define E1000_PULSE_NO_STR 0 /* no pulse stretching */ 302#define E1000_PULSE_21MS 1 /* 21 ms to 42 ms */ 303#define E1000_PULSE_42MS 2 /* 42 ms to 84 ms */ 304#define E1000_PULSE_84MS 3 /* 84 ms to 170 ms */ 305#define E1000_PULSE_170MS 4 /* 170 ms to 340 ms */ 306#define E1000_PULSE_340MS 5 /* 340 ms to 670 ms */ 307#define E1000_PULSE_670MS 6 /* 670 ms to 1300 ms */ 308#define E1000_PULSE_1300MS 7 /* 1300 ms to 2700 ms */ 309#define E1000_PULSE_DUR(x) ((x) & E1000_PULSE_MASK) 310 311#define E1000_BLINK_MASK 0x0700 312#define E1000_BLINK_42MS 0 /* 42 ms */ 313#define E1000_BLINK_84MS 1 /* 84 ms */ 314#define E1000_BLINK_170MS 2 /* 170 ms */ 315#define E1000_BLINK_340MS 3 /* 340 ms */ 316#define E1000_BLINK_670MS 4 /* 670 ms */ 317#define E1000_BLINK_RATE(x) ((x) & E1000_BLINK_MASK) 318 319#define E1000_ISR 0x13 /* interrupt status reg */ 320#define E1000_ISR_JABBER 0x0001 321#define E1000_ISR_POLARITY_CHANGE 0x0002 322#define E1000_ISR_MDIX_CHANGE 0x0040 323#define E1000_ISR_FIFO_OVER_UNDERUN 0x0080 324#define E1000_ISR_FALSE_CARRIER 0x0100 325#define E1000_ISR_SYMBOL_ERROR 0x0200 326#define E1000_ISR_LINK_STAT_CHANGE 0x0400 327#define E1000_ISR_AUTO_NEG_COMPLETE 0x0800 328#define E1000_ISR_PAGE_RECEIVED 0x1000 329#define E1000_ISR_DUPLEX_CHANGED 0x2000 330#define E1000_ISR_SPEED_CHANGED 0x4000 331#define E1000_ISR_AUTO_NEG_ERR 0x8000 332 333#define E1000_ESCR 0x14 /* extended special control reg */ 334#define E1000_ESCR_FIBER_LOOPBACK 0x4000 335#define E1000_ESCR_DOWN_NO_IDLE 0x8000 336#define E1000_ESCR_TX_CLK_2_5 0x0060 337#define E1000_ESCR_TX_CLK_25 0x0070 338#define E1000_ESCR_TX_CLK_0 0x0000 339 340#define E1000_RECR 0x15 /* RX error counter reg */ 341 342#define E1000_EADR 0x16 /* extended address reg */ 343 344#define E1000_LCR 0x18 /* LED control reg */ 345#define E1000_LCR_LED_TX 0x0001 346#define E1000_LCR_LED_RX 0x0002 347#define E1000_LCR_LED_DUPLEX 0x0004 348#define E1000_LCR_LINK 0x0008 349#define E1000_LCR_BLINK_42MS 0x0000 350#define E1000_LCR_BLINK_84MS 0x0100 351#define E1000_LCR_BLINK_170MS 0x0200 352#define E1000_LCR_BLINK_340MS 0x0300 353#define E1000_LCR_BLINK_670MS 0x0400 354#define E1000_LCR_PULSE_OFF 0x0000 355#define E1000_LCR_PULSE_21_42MS 0x1000 356#define E1000_LCR_PULSE_42_84MS 0x2000 357#define E1000_LCR_PULSE_84_170MS 0x3000 358#define E1000_LCR_PULSE_170_340MS 0x4000 359#define E1000_LCR_PULSE_340_670MS 0x5000 360#define E1000_LCR_PULSE_670_13S 0x6000 361#define E1000_LCR_PULSE_13_26S 0x7000 362 363/* The following register is found only on the 88E1011 Alaska PHY */ 364#define E1000_ESSR 0x1B /* Extended PHY specific sts */ 365#define E1000_ESSR_FIBER_LINK 0x2000 366#define E1000_ESSR_GMII_COPPER 0x000f 367#define E1000_ESSR_GMII_FIBER 0x0007 368#define E1000_ESSR_TBI_COPPER 0x000d 369#define E1000_ESSR_TBI_FIBER 0x0005 370