z8530.h revision 137955
1/* 2 * Copyright (c) 2003 Marcel Moolenaar 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 16 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 17 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 18 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 19 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 20 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 21 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 22 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 23 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 24 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 25 * 26 * $FreeBSD: head/sys/dev/ic/z8530.h 137955 2004-11-21 01:34:15Z marcel $ 27 */ 28 29#ifndef _DEV_IC_Z8530_H_ 30#define _DEV_IC_Z8530_H_ 31 32/* 33 * Channel B control: 0 34 * Channel B data: 1 35 * Channel A control: 2 36 * Channel A data: 3 37 * 38 * We expect a seperate subregion for each channel. 39 */ 40#define REG_CTRL 0 41#define REG_DATA 1 42 43/* Write registers. */ 44#define WR_CR 0 /* Command Register. */ 45#define WR_IDT 1 /* Interrupt and Data Transfer Mode. */ 46#define WR_IV 2 /* Interrupt Vector (shared). */ 47#define WR_RPC 3 /* Receive Parameters and Control. */ 48#define WR_MPM 4 /* Miscellaneous Parameters and Modes. */ 49#define WR_TPC 5 /* Transmit Parameters and Control. */ 50#define WR_SCAF 6 /* Sync Character or (SDLC) Address Field. */ 51#define WR_SCF 7 /* Sync Character or (SDCL) Flag. */ 52#define WR_EFC 7 /* Extended Feature and FIFO Control. */ 53#define WR_TB 8 /* Transmit Buffer. */ 54#define WR_MIC 9 /* Master Interrupt Control (shared). */ 55#define WR_MCB1 10 /* Miscellaneous Control Bits (part 1 :-). */ 56#define WR_CMC 11 /* Clock Mode Control. */ 57#define WR_TCL 12 /* BRG Time Constant Low. */ 58#define WR_TCH 13 /* BRG Time Constant High. */ 59#define WR_MCB2 14 /* Miscellaneous Control Bits (part 2 :-). */ 60#define WR_IC 15 /* Interrupt Control. */ 61 62/* Read registers. */ 63#define RR_BES 0 /* Buffer and External Status. */ 64#define RR_SRC 1 /* Special Receive Condition. */ 65#define RR_IV 2 /* Interrupt Vector. */ 66#define RR_IP 3 /* Interrupt Pending (ch A only). */ 67#define RR_MPM 4 /* Miscellaneous Parameters and Modes. */ 68#define RR_TPC 5 /* Transmit Parameters and Control. */ 69#define RR_BCL 6 /* Byte Count Low. */ 70#define RR_BCH 7 /* Byte Count High. */ 71#define RR_RB 8 /* Receive Buffer. */ 72#define RR_RPC 9 /* Receive Parameters and Contro. */ 73#define RR_MSB 10 /* Miscellaneous Status Bits. */ 74#define RR_MCB1 11 /* Miscellaneous Control Bits (part 1). */ 75#define RR_TCL 12 /* BRG Time Constant Low. */ 76#define RR_TCH 13 /* BRG Time Constant High. */ 77#define RR_EFC 14 /* Extended Feature and FIFO Control. */ 78#define RR_IC 15 /* Interrupt Control. */ 79 80/* Buffer and External Status (RR0). */ 81#define BES_BRK 0x80 /* Break (Abort). */ 82#define BES_TXU 0x40 /* Tx Underrun (EOM). */ 83#define BES_CTS 0x20 /* CTS. */ 84#define BES_SYNC 0x10 /* Sync. */ 85#define BES_DCD 0x08 /* DCD. */ 86#define BES_TXE 0x04 /* Tx Empty. */ 87#define BES_ZC 0x02 /* Zero Count. */ 88#define BES_RXA 0x01 /* Rx Available. */ 89 90/* Clock Mode Control (WR11). */ 91#define CMC_XTAL 0x80 /* -RTxC connects to quartz crystal. */ 92#define CMC_RC_DPLL 0x60 /* Rx Clock from DPLL. */ 93#define CMC_RC_BRG 0x40 /* Rx Clock from BRG. */ 94#define CMC_RC_TRXC 0x20 /* Rx Clock from -TRxC. */ 95#define CMC_RC_RTXC 0x00 /* Rx Clock from -RTxC. */ 96#define CMC_TC_DPLL 0x18 /* Tx Clock from DPLL */ 97#define CMC_TC_BRG 0x10 /* Tx Clock from BRG */ 98#define CMC_TC_TRXC 0x08 /* Tx Clock from -TRxC. */ 99#define CMC_TC_RTXC 0x00 /* Tx Clock from -RTxC. */ 100#define CMC_TRXC_OUT 0x04 /* -TRxC is output. */ 101#define CMC_TRXC_DPLL 0x03 /* -TRxC from DPLL */ 102#define CMC_TRXC_BRG 0x02 /* -TRxC from BRG */ 103#define CMC_TRXC_XMIT 0x01 /* -TRxC from Tx clock. */ 104#define CMC_TRXC_XTAL 0x00 /* -TRxC from XTAL. */ 105 106/* Command Register (WR0). */ 107#define CR_RSTTXU 0xc0 /* Reset Tx. Underrun/EOM. */ 108#define CR_RSTTXCRC 0x80 /* Reset Tx. CRC. */ 109#define CR_RSTRXCRC 0x40 /* Reset Rx. CRC. */ 110#define CR_RSTIUS 0x38 /* Reset Int. Under Service. */ 111#define CR_RSTERR 0x30 /* Error Reset. */ 112#define CR_RSTTXI 0x28 /* Reset Tx. Int. */ 113#define CR_ENARXI 0x20 /* Enable Rx. Int. */ 114#define CR_ABORT 0x18 /* Send Abort. */ 115#define CR_RSTXSI 0x10 /* Reset Ext/Status Int. */ 116 117/* Extended Feature and FIFO Control (WR7 prime). */ 118#define EFC_ERE 0x40 /* Extended Read Enable. */ 119#define EFC_FE 0x20 /* Transmit FIFO Empty. */ 120#define EFC_RQT 0x10 /* Request Timing. */ 121#define EFC_FHF 0x08 /* Receive FIFO Half Full. */ 122#define EFC_RTS 0x04 /* Auto RTS Deactivation. */ 123#define EFC_EOM 0x02 /* Auto EOM Reset. */ 124#define EFC_FLAG 0x01 /* Auto SDLC Flag on Tx. */ 125 126/* Interrupt Control (WR15). */ 127#define IC_BRK 0x80 /* Break (Abort) IE. */ 128#define IC_TXU 0x40 /* Tx Underrun IE. */ 129#define IC_CTS 0x20 /* CTS IE. */ 130#define IC_SYNC 0x10 /* Sync IE. */ 131#define IC_DCD 0x08 /* DCD IE. */ 132#define IC_FIFO 0x04 /* SDLC FIFO Enable. */ 133#define IC_ZC 0x02 /* Zero Count IE. */ 134#define IC_EF 0x01 /* Extended Feature Enable. */ 135 136/* Interrupt and Data Transfer Mode (WR1). */ 137#define IDT_WRE 0x80 /* Wait/DMA Request Enable. */ 138#define IDT_REQ 0x40 /* DMA Request. */ 139#define IDT_WRR 0x20 /* Wait/DMA Reuest on Receive. */ 140#define IDT_RISC 0x18 /* Rx Int. on Special Condition Only. */ 141#define IDT_RIA 0x10 /* Rx Int. on All Characters. */ 142#define IDT_RIF 0x08 /* Rx Int. on First Character. */ 143#define IDT_PSC 0x04 /* Parity is Special Condition. */ 144#define IDT_TIE 0x02 /* Tx Int. Enable. */ 145#define IDT_XIE 0x01 /* Ext. Int. Enable. */ 146 147/* Interrupt Pending (RR3). */ 148#define IP_RIA 0x20 /* Rx. Int. ch. A. */ 149#define IP_TIA 0x10 /* Tx. Int. ch. A. */ 150#define IP_SIA 0x08 /* Ext/Status Int. ch. A. */ 151#define IP_RIB 0x04 /* Rx. Int. ch. B. */ 152#define IP_TIB 0x02 /* Tx. Int. ch. B. */ 153#define IP_SIB 0x01 /* Ext/Status Int. ch. B. */ 154 155/* Interrupt Vector Status Low (RR2). */ 156#define IV_SCA 0x0e /* Special Condition ch. A. */ 157#define IV_RAA 0x0c /* Receive Available ch. A. */ 158#define IV_XSA 0x0a /* External/Status Change ch. A. */ 159#define IV_TEA 0x08 /* Transmitter Empty ch. A. */ 160#define IV_SCB 0x06 /* Special Condition ch. B. */ 161#define IV_RAB 0x04 /* Receive Available ch. B. */ 162#define IV_XSB 0x02 /* External/Status Change ch. B. */ 163#define IV_TEB 0x00 /* Transmitter Empty ch. B. */ 164 165/* Miscellaneous Control Bits part 1 (WR10). */ 166#define MCB1_CRC1 0x80 /* CRC presets to 1. */ 167#define MCB1_FM0 0x60 /* FM0 Encoding. */ 168#define MCB1_FM1 0x40 /* FM1 Encoding. */ 169#define MCB1_NRZI 0x20 /* NRZI Encoding. */ 170#define MCB1_NRZ 0x00 /* NRZ Encoding. */ 171#define MCB1_AOP 0x10 /* Active On Poll. */ 172#define MCB1_MI 0x08 /* Mark Idle. */ 173#define MCB1_AOU 0x04 /* Abort On Underrun. */ 174#define MCB1_LM 0x02 /* Loop Mode. */ 175#define MCB1_SIX 0x01 /* 6 or 12 bit SYNC. */ 176 177/* Miscellaneous Control Bits part 2 (WR14). */ 178#define MCB2_NRZI 0xe0 /* DPLL - NRZI mode. */ 179#define MCB2_FM 0xc0 /* DPLL - FM mode. */ 180#define MCB2_RTXC 0xa0 /* DPLL - Clock from -RTxC. */ 181#define MCB2_BRG 0x80 /* DPLL - Clock from BRG. */ 182#define MCB2_OFF 0x60 /* DPLL - Disable. */ 183#define MCB2_RMC 0x40 /* DPLL - Reset Missing Clock. */ 184#define MCB2_ESM 0x20 /* DPLL - Enter Search Mode. */ 185#define MCB2_LL 0x10 /* Local Loopback. */ 186#define MCB2_AE 0x08 /* Auto Echo. */ 187#define MCB2_REQ 0x04 /* Request Function. */ 188#define MCB2_PCLK 0x02 /* BRG source is PCLK. */ 189#define MCB2_BRGE 0x01 /* BRG enable. */ 190 191/* Master Interrupt Control (WR9). */ 192#define MIC_FHR 0xc0 /* Force Hardware Reset. */ 193#define MIC_CRA 0x80 /* Channel Reset A. */ 194#define MIC_CRB 0x40 /* Channel Reset B. */ 195#define MIC_SIE 0x20 /* Software INTACK Enable. */ 196#define MIC_SH 0x10 /* Status High. */ 197#define MIC_MIE 0x08 /* Master Interrupt Enable. */ 198#define MIC_DLC 0x04 /* Disable Lower Chain. */ 199#define MIC_NV 0x02 /* No Vector. */ 200#define MIC_VIS 0x01 /* Vector Includes Status. */ 201 202/* Transmit/Receive Miscellaneous Parameters and Modes (WR4). */ 203#define MPM_CM64 0xc0 /* X64 Clock Mode. */ 204#define MPM_CM32 0x80 /* X32 Clock Mode. */ 205#define MPM_CM16 0x40 /* X16 Clock Mode. */ 206#define MPM_CM1 0x00 /* X1 Clock Mode. */ 207#define MPM_EXT 0x30 /* External Sync Mode. */ 208#define MPM_SDLC 0x20 /* SDLC mode. */ 209#define MPM_BI 0x10 /* 16-bit Sync (bi-sync). */ 210#define MPM_MONO 0x00 /* 8-bit Sync (mono-sync). */ 211#define MPM_SB2 0x0c /* Async mode: 2 stopbits. */ 212#define MPM_SB15 0x08 /* Async mode: 1.5 stopbits. */ 213#define MPM_SB1 0x04 /* Async mode: 1 stopbit. */ 214#define MPM_SYNC 0x00 /* Sync Mode Enable. */ 215#define MPM_EVEN 0x02 /* Async mode: even parity. */ 216#define MPM_PE 0x01 /* Async mode: parity enable. */ 217 218/* Receive Parameters and Control (WR3). */ 219#define RPC_RB8 0xc0 /* 8 databits. */ 220#define RPC_RB6 0x80 /* 6 databits. */ 221#define RPC_RB7 0x40 /* 7 databits. */ 222#define RPC_RB5 0x00 /* 5 databits. */ 223#define RPC_AE 0x20 /* Auto Enable. */ 224#define RPC_EHM 0x10 /* Enter Hunt Mode. */ 225#define RPC_CRC 0x08 /* CRC Enable. */ 226#define RPC_ASM 0x04 /* Address Search Mode. */ 227#define RPC_LI 0x02 /* SYNC Character Load Inhibit */ 228#define RPC_RXE 0x01 /* Receiver Enable */ 229 230/* Special Receive Condition (RR1). */ 231#define SRC_EOF 0x80 /* End Of Frame. */ 232#define SRC_FE 0x40 /* Framing Error. */ 233#define SRC_OVR 0x20 /* Rx. Overrun. */ 234#define SRC_PE 0x10 /* Parity Error. */ 235#define SRC_RC0 0x08 /* Residue Code 0. */ 236#define SRC_RC1 0x04 /* Residue Code 1. */ 237#define SRC_RC2 0x02 /* Residue Code 2. */ 238#define SRC_AS 0x01 /* All Sent. */ 239 240/* Transmit Parameter and Control (WR5). */ 241#define TPC_DTR 0x80 /* DTR. */ 242#define TPC_TB8 0x60 /* 8 databits. */ 243#define TPC_TB6 0x40 /* 6 databits. */ 244#define TPC_TB7 0x20 /* 7 databits. */ 245#define TPC_TB5 0x00 /* 5 or fewer databits. */ 246#define TPC_BRK 0x10 /* Send break. */ 247#define TPC_TXE 0x08 /* Transmitter Enable. */ 248#define TPC_CRC16 0x04 /* CRC16. */ 249#define TPC_RTS 0x02 /* RTS. */ 250#define TPC_CRC 0x01 /* CRC Enable. */ 251 252#endif /* _DEV_IC_Z8530_H_ */ 253