sab82532.h revision 285830
1/* $OpenBSD: sab82532reg.h,v 1.2 2002/04/08 17:49:42 jason Exp $ */ 2 3/*- 4 * Copyright (c) 2001 Jason L. Wright (jason@thought.net) 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 3. All advertising materials mentioning features or use of this software 16 * must display the following acknowledgement: 17 * This product includes software developed by Jason L. Wright 18 * 4. The name of the author may not be used to endorse or promote products 19 * derived from this software without specific prior written permission. 20 * 21 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 22 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 23 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 24 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, 25 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 26 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 27 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 28 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 29 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN 30 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 31 * POSSIBILITY OF SUCH DAMAGE. 32 * 33 * Effort sponsored in part by the Defense Advanced Research Projects 34 * Agency (DARPA) and Air Force Research Laboratory, Air Force 35 * Materiel Command, USAF, under agreement number F30602-01-2-0537. 36 * 37 * $FreeBSD: releng/10.2/sys/dev/ic/sab82532.h 139749 2005-01-06 01:43:34Z imp $ 38 */ 39 40#ifndef _DEV_IC_SAB82532_H_ 41#define _DEV_IC_SAB82532_H_ 42 43/* 44 * Register definitions for SAB82532 based on "Enhanced Serial Communication 45 * Controller ESCC2 Version 3.2 User's Manual 07.96" from: 46 * http://www.infineon.com 47 */ 48 49#define SAB_NCHAN 2 /* number of channels */ 50#define SAB_CHANLEN 0x40 /* length of channel register set */ 51 52#define SAB_CHAN_A 0x00 /* channel A register offset */ 53#define SAB_CHAN_B 0x40 /* channel B register offset */ 54 55#define SAB_RFIFO 0x00 /* r: rx fifo */ 56#define SAB_XFIFO 0x00 /* w: tx fifo */ 57#define SAB_STAR 0x20 /* r: status register */ 58#define SAB_CMDR 0x20 /* w: command register */ 59#define SAB_MODE 0x22 /* rw: mode register */ 60#define SAB_TIMR 0x23 /* rw: timer register */ 61#define SAB_XON 0x24 /* rw: xon character */ 62#define SAB_XOFF 0x25 /* rw: xoff character */ 63#define SAB_TCR 0x26 /* rw: termination character */ 64#define SAB_DAFO 0x27 /* rw: data format */ 65#define SAB_RFC 0x28 /* rw: rfifo control register */ 66#define SAB_RBCL 0x2a /* r: rx byte count low */ 67#define SAB_TBCL 0x2a /* w: tx byte count low */ 68#define SAB_RBCH 0x2b /* r: rx byte count high */ 69#define SAB_XBCH 0x2b /* w: tx byte count high */ 70#define SAB_CCR0 0x2c /* rw: channel configuration register 0 */ 71#define SAB_CCR1 0x2d /* rw: channel configuration register 1 */ 72#define SAB_CCR2 0x2e /* rw: channel configuration register 2 */ 73#define SAB_CCR3 0x2f /* rw: channel configuration register 3 */ 74#define SAB_TSAX 0x30 /* w: time-slot assignment register tx */ 75#define SAB_TSAR 0x31 /* w: time-slot assignment register rx */ 76#define SAB_XCCR 0x32 /* w: tx channel capacity register */ 77#define SAB_RCCR 0x33 /* w: receive channel capacity register */ 78#define SAB_VSTR 0x34 /* r: version status */ 79#define SAB_BGR 0x34 /* w: baud rate generator */ 80#define SAB_TIC 0x35 /* w: transmit immediate character */ 81#define SAB_MXN 0x36 /* w: mask xon character */ 82#define SAB_MXF 0x37 /* w: mask xoff character */ 83#define SAB_GIS 0x38 /* r: global interrupt status */ 84#define SAB_IVA 0x38 /* w: interrupt vector address */ 85#define SAB_IPC 0x39 /* rw: interrupt port configuration */ 86#define SAB_ISR0 0x3a /* r: interrupt status 0 */ 87#define SAB_IMR0 0x3a /* w: interrupt mask 0 */ 88#define SAB_ISR1 0x3b /* r: interrupt status 1 */ 89#define SAB_IMR1 0x3b /* w: interrupt mask 1 */ 90#define SAB_PVR 0x3c /* rw: port value register */ 91#define SAB_PIS 0x3d /* r: port interrupt status */ 92#define SAB_PIM 0x3d /* w: port interrupt mask */ 93#define SAB_PCR 0x3e /* w: port configuration register */ 94#define SAB_CCR4 0x3f /* rw: channel configuration register 4 */ 95 96/* SAB_STAR: status register */ 97#define SAB_STAR_XDOV 0x80 /* transmit data overflow */ 98#define SAB_STAR_XFW 0x40 /* transmit fifo write enable */ 99#define SAB_STAR_RFNE 0x20 /* rfifo not empty */ 100#define SAB_STAR_FCS 0x10 /* flow control status */ 101#define SAB_STAR_TEC 0x08 /* tx immediate char is executing */ 102#define SAB_STAR_CEC 0x04 /* command is executing */ 103#define SAB_STAR_CTS 0x02 /* cts status: 0:inactive/high,1:active/low */ 104 105/* SAB_CMDR: command register */ 106#define SAB_CMDR_RMC 0x80 /* receive message complete */ 107#define SAB_CMDR_RRES 0x40 /* receiver reset */ 108#define SAB_CMDR_RFRD 0x20 /* receive fifo read enable */ 109#define SAB_CMDR_STI 0x10 /* start timer */ 110#define SAB_CMDR_XF 0x08 /* transmit frame */ 111#define SAB_CMDR_XRES 0x01 /* transmit reset */ 112 113/* SAB_MODE: mode register */ 114#define SAB_MODE_FRTS 0x40 /* flow control using rts */ 115#define SAB_MODE_FCTS 0x20 /* flow control using cts */ 116#define SAB_MODE_FLON 0x10 /* flow control on */ 117#define SAB_MODE_RAC 0x08 /* receiver active */ 118#define SAB_MODE_RTS 0x04 /* request to send */ 119#define SAB_MODE_TRS 0x02 /* timer resolution */ 120#define SAB_MODE_TLP 0x01 /* test loop */ 121 122/* SAB_TIMR: timer register */ 123#define SAB_TIMR_CNT 0xe0 /* count mask */ 124#define SAB_TIMR_VAL 0x1f /* value mask */ 125 126/* SAB_DAFO: data format */ 127#define SAB_DAFO_XBRK 0x40 /* transmit break */ 128#define SAB_DAFO_STOP 0x20 /* stop bit: 0:1 bit, 1:2 bits */ 129#define SAB_DAFO_PAR1 0x10 /* parity 1, see below */ 130#define SAB_DAFO_PAR0 0x08 /* parity 0, see below */ 131#define SAB_DAFO_PARE 0x04 /* parity enable */ 132#define SAB_DAFO_CHL1 0x02 /* character length 1, see below */ 133#define SAB_DAFO_CHL0 0x01 /* character length 0, see below */ 134 135#define SAB_DAFO_CHL_CSIZE (SAB_DAFO_CHL1|SAB_DAFO_CHL0) 136#define SAB_DAFO_CHL_CS5 (SAB_DAFO_CHL1|SAB_DAFO_CHL0) 137#define SAB_DAFO_CHL_CS6 (SAB_DAFO_CHL1) 138#define SAB_DAFO_CHL_CS7 (SAB_DAFO_CHL0) 139#define SAB_DAFO_CHL_CS8 (0) 140 141#define SAB_DAFO_PARMASK (SAB_DAFO_PAR1|SAB_DAFO_PAR0|SAB_DAFO_PARE) 142#define SAB_DAFO_PAR_MARK (SAB_DAFO_PAR1|SAB_DAFO_PAR0|SAB_DAFO_PARE) 143#define SAB_DAFO_PAR_EVEN (SAB_DAFO_PAR1|SAB_DAFO_PARE) 144#define SAB_DAFO_PAR_ODD (SAB_DAFO_PAR0|SAB_DAFO_PARE) 145#define SAB_DAFO_PAR_SPACE (SAB_DAFO_PARE) 146#define SAB_DAFO_PAR_NONE (0) 147 148/* SAB_RFC: rfifo control register */ 149#define SAB_RFC_DPS 0x40 /* disable parity storage */ 150#define SAB_RFC_DXS 0x20 /* disable storage of xon/xoff characters */ 151#define SAB_RFC_RFDF 0x10 /* rfifo data format: 0 data,1 data+stat */ 152#define SAB_RFC_RFTH1 0x08 /* rfifo threshold level 1, see below */ 153#define SAB_RFC_RFTH0 0x04 /* rfifo threshold level 0, see below */ 154#define SAB_RFC_TCDE 0x01 /* termination character detection enable */ 155 156#define SAB_RFC_RFTH_MASK (SAB_RFC_RFTH1|SAB_RFC_RFTH0) 157#define SAB_RFC_RFTH_32CHAR (SAB_RFC_RFTH1|SAB_RFC_RFTH0) 158#define SAB_RFC_RFTH_16CHAR (SAB_RFC_RFTH1) 159#define SAB_RFC_RFTH_4CHAR (SAB_RFC_RFTH0) 160#define SAB_RFC_RFTH_1CHAR (0) 161 162/* SAB_RBCH: received byte count high */ 163#define SAB_RBCH_DMA 0x80 /* read back of XBCH DMA bit */ 164#define SAB_RBCH_CAS 0x20 /* read back of XBCH CAS bit */ 165#define SAB_RBCH_CNT 0x0f /* ms 4 bits of rx byte count (not used) */ 166 167/* SAB_XBCH: transmit byte count high */ 168#define SAB_XBCH_DMA 0x80 /* dma mode: 1:dma, 0:interrupt */ 169#define SAB_XBCH_CAS 0x20 /* carrier detect auto-start */ 170#define SAB_XBCH_XC 0x10 /* transmit continuously */ 171#define SAB_XBCH_CNT 0x0f /* ms 4 bits of tx byte count */ 172 173/* SAB_CCR0: channel configuration register 0 */ 174#define SAB_CCR0_PU 0x80 /* 0:power-down, 1:power-up */ 175#define SAB_CCR0_MCE 0x40 /* master clock enable */ 176#define SAB_CCR0_SC2 0x10 /* serial port config 2, see below */ 177#define SAB_CCR0_SC1 0x08 /* serial port config 1, see below */ 178#define SAB_CCR0_SC0 0x04 /* serial port config 0, see below */ 179#define SAB_CCR0_SM1 0x02 /* serial mode 1, see below */ 180#define SAB_CCR0_SM0 0x01 /* serial mode 0, see below */ 181 182#define SAB_CCR0_SC_MASK (SAB_CCR0_SC2|SAB_CCR0_SC1|SAB_CCR0_SC0) 183#define SAB_CCR0_SC_NRZ (0) 184#define SAB_CCR0_SC_NRZI (SAB_CCR0_SC1) 185#define SAB_CCR0_SC_FM0 (SAB_CCR0_SC2) 186#define SAB_CCR0_SC_FM1 (SAB_CCR0_SC2|SAB_CCR0_SC0) 187#define SAB_CCR0_SC_MANCHESTER (SAB_CCR0_SC2|SAB_CCR0_SC1) 188 189#define SAB_CCR0_SM_MASK (SAB_CCR0_SM1|SAB_CCR0_SM0) 190#define SAB_CCR0_SM_DLC (0) 191#define SAB_CCR0_SM_DLCLOOP (SAB_CCR0_SM0) 192#define SAB_CCR0_SM_BISYNC (SAB_CCR0_SM1) 193#define SAB_CCR0_SM_ASYNC (SAB_CCR0_SM1|SAB_CCR0_SM0) 194 195/* SAB_CCR1: channel configuration register 1 */ 196#define SAB_CCR1_ODS 0x10 /* Output driver select:1:pushpull,0:odrain */ 197#define SAB_CCR1_BCR 0x08 /* bit clock rate: 1:async, 0:isochronous */ 198#define SAB_CCR1_CM2 0x04 /* clock mode 2, see below */ 199#define SAB_CCR1_CM1 0x02 /* clock mode 1, see below */ 200#define SAB_CCR1_CM0 0x01 /* clock mode 0, see below */ 201 202#define SAB_CCR1_CM_MASK (SAB_CCR1_CM2|SAB_CCR1_CM1|SAB_CCR1_CM0) 203#define SAB_CCR1_CM_7 (SAB_CCR1_CM2|SAB_CCR1_CM1|SAB_CCR1_CM0) 204 205/* SAB_CCR2: channel configuration register 2, depends on clock mode above */ 206/* clock mode 0a, 1, 4, 5 */ 207#define SAB_CCR2_SOC1 0x80 /* special output 1, below */ 208#define SAB_CCR2_SOC0 0x40 /* special output 0, below */ 209#define SAB_CCR2_SOC_MASK (SAB_CCR2_SOC1|SAB_CCR2_SOC0) 210#define SAB_CCR2_SOC_RTSHIGH (SAB_CCR2_SOC1) 211#define SAB_CCR2_SOC_RTSNORM (0) 212#define SAB_CCR2_SOC_RTSRX (SAB_CCR2_SOC1|SAB_CCR2_SOC0) 213/* clock mode 0b, 2, 3, 6, 7 */ 214#define SAB_CCR2_BR9 0x80 /* baud rate bit 9 */ 215#define SAB_CCR2_BR8 0x40 /* baud rate bit 8 */ 216#define SAB_CCR2_BDF 0x20 /* baud rate division factor: 0:1: 1:BRG */ 217#define SAB_CCR2_SSEL 0x10 /* clock source select */ 218/* clock mode 5 */ 219#define SAB_CCR2_XCS0 0x20 /* tx clock shift, bit 0 */ 220#define SAB_CCR2_RCS0 0x10 /* rx clock shift, bit 0 */ 221/* clock mode 0b, 2, 3, 4, 5, 6, 7 */ 222#define SAB_CCR2_TOE 0x08 /* tx clock output enable */ 223/* clock mode 0a, 0b, 1, 2, 3, 4, 5, 6, 7 */ 224#define SAB_CCR2_RWX 0x04 /* read/write exchange (dma mode only) */ 225#define SAB_CCR2_DIV 0x01 /* data inversion (nrz) */ 226 227/* SAB_CCR3: channel configuration register 3 (v2 or greater) */ 228#define SAB_CCR3_PSD 0x01 /* dpll phase shift disable (nrz/nrzi) */ 229 230/* SAB_TSAX: time-slot assignment register transmit (clock mode 5 only) */ 231#define SAB_TSAX_TSNX 0xfc /* time-slot number transmit */ 232#define SAB_TSAX_XCS2 0x02 /* transmit clock shift bit 2 */ 233#define SAB_TSAX_XCS1 0x01 /* transmit clock shift bit 1 */ 234 235/* SAB_TSAR: time-slot assignment register receive (clock mode 5 only) */ 236#define SAB_TSAR_TSNR 0xfc /* time-slot number receive */ 237#define SAB_TSAR_RCS2 0x02 /* receive clock shift bit 2 */ 238#define SAB_TSAR_RCS1 0x01 /* receive clock shift bit 1 */ 239 240/* SAB_VSTR: version status register */ 241#define SAB_VSTR_CD 0x80 /* carrier detect status */ 242#define SAB_VSTR_DPLA 0x40 /* dpll asynchronous */ 243#define SAB_VSTR_VMASK 0x0f /* chip version mask: */ 244#define SAB_VSTR_V_1 0x00 /* version 1 */ 245#define SAB_VSTR_V_2 0x01 /* version 2 */ 246#define SAB_VSTR_V_32 0x02 /* version 3.2 */ 247 248/* SAB_GIS: global interrupt status register */ 249#define SAB_GIS_PI 0x80 /* universal port interrupt */ 250#define SAB_GIS_ISA1 0x08 /* interrupt status a1 */ 251#define SAB_GIS_ISA0 0x04 /* interrupt status a0 */ 252#define SAB_GIS_ISB1 0x02 /* interrupt status b1 */ 253#define SAB_GIS_ISB0 0x01 /* interrupt status b0 */ 254 255/* SAB_IVA: interrupt vector address */ 256#define SAB_IVA_MASK 0xf8 /* interrupt vector address mask */ 257 258/* SAB_IPC: interrupt port configuration */ 259#define SAB_IPC_VIS 0x80 /* masked interrupt bits visible */ 260#define SAB_IPC_SLAMASK 0x18 /* slave address mask */ 261#define SAB_IPC_CASM 0x04 /* cascading mode */ 262#define SAB_IPC_ICMASK 0x03 /* port config mask: */ 263#define SAB_IPC_ICOD 0x00 /* open drain output */ 264#define SAB_IPC_ICPL 0x01 /* push/pull active low output */ 265#define SAB_IPC_ICPH 0x03 /* push/pull active high output */ 266 267/* SAB_ISR0: interrupt status 0 */ 268#define SAB_ISR0_TCD 0x80 /* termination character detected */ 269#define SAB_ISR0_TIME 0x40 /* time-out limit exceeded */ 270#define SAB_ISR0_PERR 0x20 /* parity error */ 271#define SAB_ISR0_FERR 0x10 /* framing error */ 272#define SAB_ISR0_PLLA 0x08 /* dpll asynchronous */ 273#define SAB_ISR0_CDSC 0x04 /* carrier detect status change */ 274#define SAB_ISR0_RFO 0x02 /* rfifo overflow */ 275#define SAB_ISR0_RPF 0x01 /* receive pool full */ 276 277/* SAB_ISR1: interrupt status 1 */ 278#define SAB_ISR1_BRK 0x80 /* break detected */ 279#define SAB_ISR1_BRKT 0x40 /* break terminated */ 280#define SAB_ISR1_ALLS 0x20 /* all sent */ 281#define SAB_ISR1_XOFF 0x10 /* xoff detected */ 282#define SAB_ISR1_TIN 0x08 /* timer interrupt */ 283#define SAB_ISR1_CSC 0x04 /* clear to send status change */ 284#define SAB_ISR1_XON 0x02 /* xon detected */ 285#define SAB_ISR1_XPR 0x01 /* transmit pool ready */ 286 287/* SAB_IMR0: interrupt mask 0 */ 288#define SAB_IMR0_TCD 0x80 /* termination character detected */ 289#define SAB_IMR0_TIME 0x40 /* time-out limit exceeded */ 290#define SAB_IMR0_PERR 0x20 /* parity error */ 291#define SAB_IMR0_FERR 0x10 /* framing error */ 292#define SAB_IMR0_PLLA 0x08 /* dpll asynchronous */ 293#define SAB_IMR0_CDSC 0x04 /* carrier detect status change */ 294#define SAB_IMR0_RFO 0x02 /* rfifo overflow */ 295#define SAB_IMR0_RPF 0x01 /* receive pool full */ 296 297/* SAB_ISR1: interrupt mask 1 */ 298#define SAB_IMR1_BRK 0x80 /* break detected */ 299#define SAB_IMR1_BRKT 0x40 /* break terminated */ 300#define SAB_IMR1_ALLS 0x20 /* all sent */ 301#define SAB_IMR1_XDU 0x10 /* xoff detected */ 302#define SAB_IMR1_TIN 0x08 /* timer interrupt */ 303#define SAB_IMR1_CSC 0x04 /* clear to send status change */ 304#define SAB_IMR1_XMR 0x02 /* xon detected */ 305#define SAB_IMR1_XPR 0x01 /* transmit pool ready */ 306 307/* SAB_PVR: port value register */ 308#define SAB_PVR_DSR_A 0x01 /* port A DSR */ 309#define SAB_PVR_DTR_A 0x02 /* port A DTR */ 310#define SAB_PVR_DTR_B 0x04 /* port B DTR */ 311#define SAB_PVR_DSR_B 0x08 /* port B DSR */ 312#define SAB_PVR_MAGIC 0x10 /* dunno... */ 313 314/* SAB_CCR4: channel configuration register 4 */ 315#define SAB_CCR4_MCK4 0x80 /* master clock divide by 4 */ 316#define SAB_CCR4_EBRG 0x40 /* enhanced baud rate generator mode */ 317#define SAB_CCR4_TST1 0x20 /* test pin */ 318#define SAB_CCR4_ICD 0x10 /* invert polarity of carrier detect */ 319 320/* Receive status byte */ 321#define SAB_RSTAT_PE 0x80 /* parity error */ 322#define SAB_RSTAT_FE 0x40 /* framing error */ 323#define SAB_RSTAT_PAR 0x01 /* parity bit */ 324 325#endif /* _DEV_IC_SAB82532_H_ */ 326