aic7xxx_93cx6.c revision 119418
1/* 2 * Interface for the 93C66/56/46/26/06 serial eeprom parts. 3 * 4 * Copyright (c) 1995, 1996 Daniel M. Eischen 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. The name of the author may not be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * Alternatively, this software may be distributed under the terms of the 17 * GNU General Public License ("GPL"). 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 23 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 29 * SUCH DAMAGE. 30 * 31 * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_93cx6.c#17 $ 32 */ 33 34#include <sys/cdefs.h> 35__FBSDID("$FreeBSD: head/sys/dev/aic7xxx/aic7xxx_93cx6.c 119418 2003-08-24 17:55:58Z obrien $"); 36 37/* 38 * The instruction set of the 93C66/56/46/26/06 chips are as follows: 39 * 40 * Start OP * 41 * Function Bit Code Address** Data Description 42 * ------------------------------------------------------------------- 43 * READ 1 10 A5 - A0 Reads data stored in memory, 44 * starting at specified address 45 * EWEN 1 00 11XXXX Write enable must precede 46 * all programming modes 47 * ERASE 1 11 A5 - A0 Erase register A5A4A3A2A1A0 48 * WRITE 1 01 A5 - A0 D15 - D0 Writes register 49 * ERAL 1 00 10XXXX Erase all registers 50 * WRAL 1 00 01XXXX D15 - D0 Writes to all registers 51 * EWDS 1 00 00XXXX Disables all programming 52 * instructions 53 * *Note: A value of X for address is a don't care condition. 54 * **Note: There are 8 address bits for the 93C56/66 chips unlike 55 * the 93C46/26/06 chips which have 6 address bits. 56 * 57 * The 93C46 has a four wire interface: clock, chip select, data in, and 58 * data out. In order to perform one of the above functions, you need 59 * to enable the chip select for a clock period (typically a minimum of 60 * 1 usec, with the clock high and low a minimum of 750 and 250 nsec 61 * respectively). While the chip select remains high, you can clock in 62 * the instructions (above) starting with the start bit, followed by the 63 * OP code, Address, and Data (if needed). For the READ instruction, the 64 * requested 16-bit register contents is read from the data out line but 65 * is preceded by an initial zero (leading 0, followed by 16-bits, MSB 66 * first). The clock cycling from low to high initiates the next data 67 * bit to be sent from the chip. 68 */ 69 70#ifdef __linux__ 71#include "aic7xxx_osm.h" 72#include "aic7xxx_inline.h" 73#include "aic7xxx_93cx6.h" 74#else 75#include <dev/aic7xxx/aic7xxx_osm.h> 76#include <dev/aic7xxx/aic7xxx_inline.h> 77#include <dev/aic7xxx/aic7xxx_93cx6.h> 78#endif 79 80/* 81 * Right now, we only have to read the SEEPROM. But we make it easier to 82 * add other 93Cx6 functions. 83 */ 84static struct seeprom_cmd { 85 uint8_t len; 86 uint8_t bits[9]; 87} seeprom_read = {3, {1, 1, 0}}; 88 89static struct seeprom_cmd seeprom_ewen = {9, {1, 0, 0, 1, 1, 0, 0, 0, 0}}; 90static struct seeprom_cmd seeprom_ewds = {9, {1, 0, 0, 0, 0, 0, 0, 0, 0}}; 91static struct seeprom_cmd seeprom_write = {3, {1, 0, 1}}; 92 93/* 94 * Wait for the SEERDY to go high; about 800 ns. 95 */ 96#define CLOCK_PULSE(sd, rdy) \ 97 while ((SEEPROM_STATUS_INB(sd) & rdy) == 0) { \ 98 ; /* Do nothing */ \ 99 } \ 100 (void)SEEPROM_INB(sd); /* Clear clock */ 101 102/* 103 * Send a START condition and the given command 104 */ 105static void 106send_seeprom_cmd(struct seeprom_descriptor *sd, struct seeprom_cmd *cmd) 107{ 108 uint8_t temp; 109 int i = 0; 110 111 /* Send chip select for one clock cycle. */ 112 temp = sd->sd_MS ^ sd->sd_CS; 113 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 114 CLOCK_PULSE(sd, sd->sd_RDY); 115 116 for (i = 0; i < cmd->len; i++) { 117 if (cmd->bits[i] != 0) 118 temp ^= sd->sd_DO; 119 SEEPROM_OUTB(sd, temp); 120 CLOCK_PULSE(sd, sd->sd_RDY); 121 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 122 CLOCK_PULSE(sd, sd->sd_RDY); 123 if (cmd->bits[i] != 0) 124 temp ^= sd->sd_DO; 125 } 126} 127 128/* 129 * Clear CS put the chip in the reset state, where it can wait for new commands. 130 */ 131static void 132reset_seeprom(struct seeprom_descriptor *sd) 133{ 134 uint8_t temp; 135 136 temp = sd->sd_MS; 137 SEEPROM_OUTB(sd, temp); 138 CLOCK_PULSE(sd, sd->sd_RDY); 139 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 140 CLOCK_PULSE(sd, sd->sd_RDY); 141 SEEPROM_OUTB(sd, temp); 142 CLOCK_PULSE(sd, sd->sd_RDY); 143} 144 145/* 146 * Read the serial EEPROM and returns 1 if successful and 0 if 147 * not successful. 148 */ 149int 150ahc_read_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, 151 u_int start_addr, u_int count) 152{ 153 int i = 0; 154 u_int k = 0; 155 uint16_t v; 156 uint8_t temp; 157 158 /* 159 * Read the requested registers of the seeprom. The loop 160 * will range from 0 to count-1. 161 */ 162 for (k = start_addr; k < count + start_addr; k++) { 163 /* 164 * Now we're ready to send the read command followed by the 165 * address of the 16-bit register we want to read. 166 */ 167 send_seeprom_cmd(sd, &seeprom_read); 168 169 /* Send the 6 or 8 bit address (MSB first, LSB last). */ 170 temp = sd->sd_MS ^ sd->sd_CS; 171 for (i = (sd->sd_chip - 1); i >= 0; i--) { 172 if ((k & (1 << i)) != 0) 173 temp ^= sd->sd_DO; 174 SEEPROM_OUTB(sd, temp); 175 CLOCK_PULSE(sd, sd->sd_RDY); 176 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 177 CLOCK_PULSE(sd, sd->sd_RDY); 178 if ((k & (1 << i)) != 0) 179 temp ^= sd->sd_DO; 180 } 181 182 /* 183 * Now read the 16 bit register. An initial 0 precedes the 184 * register contents which begins with bit 15 (MSB) and ends 185 * with bit 0 (LSB). The initial 0 will be shifted off the 186 * top of our word as we let the loop run from 0 to 16. 187 */ 188 v = 0; 189 for (i = 16; i >= 0; i--) { 190 SEEPROM_OUTB(sd, temp); 191 CLOCK_PULSE(sd, sd->sd_RDY); 192 v <<= 1; 193 if (SEEPROM_DATA_INB(sd) & sd->sd_DI) 194 v |= 1; 195 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 196 CLOCK_PULSE(sd, sd->sd_RDY); 197 } 198 199 buf[k - start_addr] = v; 200 201 /* Reset the chip select for the next command cycle. */ 202 reset_seeprom(sd); 203 } 204#ifdef AHC_DUMP_EEPROM 205 printf("\nSerial EEPROM:\n\t"); 206 for (k = 0; k < count; k = k + 1) { 207 if (((k % 8) == 0) && (k != 0)) { 208 printf ("\n\t"); 209 } 210 printf (" 0x%x", buf[k]); 211 } 212 printf ("\n"); 213#endif 214 return (1); 215} 216 217/* 218 * Write the serial EEPROM and return 1 if successful and 0 if 219 * not successful. 220 */ 221int 222ahc_write_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, 223 u_int start_addr, u_int count) 224{ 225 uint16_t v; 226 uint8_t temp; 227 int i, k; 228 229 /* Place the chip into write-enable mode */ 230 send_seeprom_cmd(sd, &seeprom_ewen); 231 reset_seeprom(sd); 232 233 /* Write all requested data out to the seeprom. */ 234 temp = sd->sd_MS ^ sd->sd_CS; 235 for (k = start_addr; k < count + start_addr; k++) { 236 /* Send the write command */ 237 send_seeprom_cmd(sd, &seeprom_write); 238 239 /* Send the 6 or 8 bit address (MSB first). */ 240 for (i = (sd->sd_chip - 1); i >= 0; i--) { 241 if ((k & (1 << i)) != 0) 242 temp ^= sd->sd_DO; 243 SEEPROM_OUTB(sd, temp); 244 CLOCK_PULSE(sd, sd->sd_RDY); 245 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 246 CLOCK_PULSE(sd, sd->sd_RDY); 247 if ((k & (1 << i)) != 0) 248 temp ^= sd->sd_DO; 249 } 250 251 /* Write the 16 bit value, MSB first */ 252 v = buf[k - start_addr]; 253 for (i = 15; i >= 0; i--) { 254 if ((v & (1 << i)) != 0) 255 temp ^= sd->sd_DO; 256 SEEPROM_OUTB(sd, temp); 257 CLOCK_PULSE(sd, sd->sd_RDY); 258 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 259 CLOCK_PULSE(sd, sd->sd_RDY); 260 if ((v & (1 << i)) != 0) 261 temp ^= sd->sd_DO; 262 } 263 264 /* Wait for the chip to complete the write */ 265 temp = sd->sd_MS; 266 SEEPROM_OUTB(sd, temp); 267 CLOCK_PULSE(sd, sd->sd_RDY); 268 temp = sd->sd_MS ^ sd->sd_CS; 269 do { 270 SEEPROM_OUTB(sd, temp); 271 CLOCK_PULSE(sd, sd->sd_RDY); 272 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 273 CLOCK_PULSE(sd, sd->sd_RDY); 274 } while ((SEEPROM_DATA_INB(sd) & sd->sd_DI) == 0); 275 276 reset_seeprom(sd); 277 } 278 279 /* Put the chip back into write-protect mode */ 280 send_seeprom_cmd(sd, &seeprom_ewds); 281 reset_seeprom(sd); 282 283 return (1); 284} 285 286int 287ahc_verify_cksum(struct seeprom_config *sc) 288{ 289 int i; 290 int maxaddr; 291 uint32_t checksum; 292 uint16_t *scarray; 293 294 maxaddr = (sizeof(*sc)/2) - 1; 295 checksum = 0; 296 scarray = (uint16_t *)sc; 297 298 for (i = 0; i < maxaddr; i++) 299 checksum = checksum + scarray[i]; 300 if (checksum == 0 301 || (checksum & 0xFFFF) != sc->checksum) { 302 return (0); 303 } else { 304 return(1); 305 } 306} 307