options revision 112689
1# $FreeBSD: head/sys/conf/options 112689 2003-03-26 20:18:40Z rwatson $ 2# 3# On the handling of kernel options 4# 5# All kernel options should be listed in NOTES, with suitable 6# descriptions. Negative options (options that make some code not 7# compile) should be commented out; LINT (generated from NOTES) should 8# compile as much code as possible. Try to structure option-using 9# code so that a single option only switch code on, or only switch 10# code off, to make it possible to have a full compile-test. If 11# necessary, you can check for COMPILING_LINT to get maximum code 12# coverage. 13# 14# All new options shall also be listed in either "conf/options" or 15# "conf/options.<machine>". Options that affect a single source-file 16# <xxx>.[c|s] should be directed into "opt_<xxx>.h", while options 17# that affect multiple files should either go in "opt_global.h" if 18# this is a kernel-wide option (used just about everywhere), or in 19# "opt_<option-name-in-lower-case>.h" if it affect only some files. 20# Note that the effect of listing only an option without a 21# header-file-name in conf/options (and cousins) is that the last 22# convention is followed. 23# 24# This handling scheme is not yet fully implemented. 25# 26# 27# Format of this file: 28# Option name filename 29# 30# If filename is missing, the default is 31# opt_<name-of-option-in-lower-case>.h 32 33# Adaptec Array Controller driver options 34AAC_DEBUG opt_aac.h # Debugging levels: 35 # 0 - quiet, only emit warnings 36 # 1 - noisy, emit major function 37 # points and things done 38 # 2 - extremely noisy, emit trace 39 # items in loops, etc. 40 41# Adaptec aic7xxx SCSI controller options 42AHC_ALLOW_MEMIO opt_aic7xxx.h # Allow PCI devices to use memory 43 # mapped I/O 44 45AHC_TMODE_ENABLE opt_aic7xxx.h # Bitmap of units to enable 46 # targetmode operations. 47 48AHC_DUMP_EEPROM opt_aic7xxx.h # Dump the contents of our 49 # configuration prom. 50 51AHC_DEBUG opt_aic7xxx.h # Compile in Aic7xxx Debugging code. 52 53AHC_DEBUG_OPTS opt_aic7xxx.h # Aic7xxx driver debugging options. 54 # See sys/dev/aic7xxx/aic7xxx.h 55 56AHC_REG_PRETTY_PRINT opt_aic7xxx.h # Print register bitfields in debug 57 # output. Adds ~128k to driver. 58 59# Adaptec aic79xx SCSI controller options 60AHD_DEBUG opt_aic79xx.h # Compile in Aic79xx Debugging code. 61 62AHD_DEBUG_OPTS opt_aic79xx.h # Aic79xx driver debugging options. 63 # See sys/dev/aic7xxx/aic79xx.h 64 65AHD_TMODE_ENABLE opt_aic79xx.h # Bitmap of units to enable 66 # targetmode operations. 67 68AHD_REG_PRETTY_PRINT opt_aic79xx.h # Print register bitfields in debug 69 # output. Adds ~215k to driver. 70 71ADW_ALLOW_MEMIO opt_adw.h # Allow PCI devices to use memory 72 # mapped I/O 73 74# Miscellaneous options. 75ALQ opt_alq.h 76ADAPTIVE_MUTEXES 77COMPAT_43 opt_compat.h 78COMPAT_FREEBSD4 opt_compat.h 79COMPAT_SUNOS opt_compat.h 80NO_COMPAT_FREEBSD4 opt_compat.h 81COMPILING_LINT opt_global.h 82CY_PCI_FASTINTR 83CONSPEED opt_comconsole.h 84DDB 85DDB_NOKLDSYM opt_ddb.h 86DDB_TRACE 87DDB_UNATTENDED 88GDB_REMOTE_CHAT opt_ddb.h 89GDBSPEED opt_ddb.h 90GEOM_AES opt_geom.h 91GEOM_APPLE opt_geom.h 92GEOM_BDE opt_geom.h 93GEOM_BSD opt_geom.h 94GEOM_GPT opt_geom.h 95GEOM_MBR opt_geom.h 96GEOM_MIRROR opt_geom.h 97GEOM_PC98 opt_geom.h 98GEOM_SUNLABEL opt_geom.h 99GEOM_VOL opt_geom.h 100HW_WDOG 101KSTACK_PAGES 102KSTACK_MAX_PAGES 103KTRACE 104KTRACE_REQUEST_POOL opt_ktrace.h 105LIBICONV 106MD_ROOT opt_md.h 107MD_ROOT_SIZE opt_md.h 108NDGBPORTS opt_dgb.h 109NTIMECOUNTER opt_ntp.h 110NSWAPDEV opt_swap.h 111PANIC_REBOOT_WAIT_TIME opt_panic.h 112PPS_SYNC opt_ntp.h 113PUC_FASTINTR opt_puc.h 114QUOTA 115SCHED_4BSD opt_sched.h 116SCHED_ULE opt_sched.h 117SHOW_BUSYBUFS 118SPX_HACK 119SUIDDIR opt_suiddir.h 120MSGMNB opt_sysvipc.h 121MSGMNI opt_sysvipc.h 122MSGSEG opt_sysvipc.h 123MSGSSZ opt_sysvipc.h 124MSGTQL opt_sysvipc.h 125SEMMAP opt_sysvipc.h 126SEMMNI opt_sysvipc.h 127SEMMNS opt_sysvipc.h 128SEMMNU opt_sysvipc.h 129SEMMSL opt_sysvipc.h 130SEMOPM opt_sysvipc.h 131SEMUME opt_sysvipc.h 132SHMALL opt_sysvipc.h 133SHMMAX opt_sysvipc.h 134SHMMAXPGS opt_sysvipc.h 135SHMMIN opt_sysvipc.h 136SHMMNI opt_sysvipc.h 137SHMSEG opt_sysvipc.h 138SYSVMSG opt_sysvipc.h 139SYSVSEM opt_sysvipc.h 140SYSVSHM opt_sysvipc.h 141VFS_AIO 142WLCACHE opt_wavelan.h 143WLDEBUG opt_wavelan.h 144TTYHOG opt_tty.h 145 146# POSIX kernel options 147_KPOSIX_PRIORITY_SCHEDULING opt_posix.h 148P1003_1B_SEMAPHORES opt_posix.h 149 150##################################################################### 151# SECURITY POLICY PARAMETERS 152 153# Support for Mandatory Access Control (MAC) 154MAC opt_mac.h 155MAC_BIBA opt_dontuse.h 156MAC_BSDEXTENDED opt_dontuse.h 157MAC_DEBUG opt_mac.h 158MAC_IFOFF opt_dontuse.h 159MAC_LOMAC opt_dontuse.h 160MAC_MLS opt_dontuse.h 161MAC_NONE opt_dontuse.h 162MAC_PARTITION opt_dontuse.h 163MAC_PORTACL opt_dontuse.h 164MAC_SEEOTHERUIDS opt_dontuse.h 165MAC_TEST opt_dontuse.h 166 167# Do we want the config file compiled into the kernel? 168INCLUDE_CONFIG_FILE opt_config.h 169 170# Options for static filesystems. These should only be used at config 171# time, since the corresponding lkms cannot work if there are any static 172# dependencies. Unusability is enforced by hiding the defines for the 173# options in a never-included header. 174CD9660 opt_dontuse.h 175CODA opt_dontuse.h 176EXT2FS opt_dontuse.h 177FDESCFS opt_dontuse.h 178LINPROCFS opt_dontuse.h 179MSDOSFS opt_dontuse.h 180NULLFS opt_dontuse.h 181NWFS opt_dontuse.h 182PORTALFS opt_dontuse.h 183PROCFS opt_dontuse.h 184PSEUDOFS opt_dontuse.h 185UMAPFS opt_dontuse.h 186NTFS opt_dontuse.h 187HPFS opt_dontuse.h 188SMBFS opt_dontuse.h 189UNIONFS opt_dontuse.h 190UDF opt_dontuse.h 191 192# Broken - ffs_snapshot() dependency from ufs_lookup() :-( 193FFS opt_ffs_broken_fixme.h 194 195# These static filesystems has one slightly bogus static dependency in 196# sys/i386/i386/autoconf.c. If any of these filesystems are 197# statically compiled into the kernel, code for mounting them as root 198# filesystems will be enabled - but look below. 199NFSCLIENT opt_nfs.h 200NFSSERVER opt_nfs.h 201 202# If you are following the conditions in the copyright, 203# you can enable soft-updates which will speed up a lot of thigs 204# and make the system safer from crashes at the same time. 205# otherwise a STUB module will be compiled in. 206SOFTUPDATES opt_ffs.h 207 208# Enabling this option turns on support for Access Control Lists in UFS, 209# which can be used to support high security configurations. Depends on 210# UFS_EXTATTR. 211UFS_ACL opt_ufs.h 212 213# Enabling this option turns on support for extended attributes in UFS-based 214# filesystems, which can be used to support high security configurations 215# as well as new filesystem features. 216UFS_EXTATTR opt_ufs.h 217UFS_EXTATTR_AUTOSTART opt_ufs.h 218 219# Enable fast hash lookups for large directories on UFS-based filesystems. 220UFS_DIRHASH opt_ufs.h 221 222# The above static dependencies are planned removed, with a 223# <filesystem>_ROOT option to control if it usable as root. This list 224# allows these options to be present in config files already (though 225# they won't make any difference yet). 226NFS_ROOT opt_nfsroot.h 227 228# SMB/CIFS requester 229NETSMB opt_netsmb.h 230NETSMBCRYPTO opt_netsmb.h 231 232# Options used only in subr_param.c. 233HZ opt_param.h 234MAXFILES opt_param.h 235NBUF opt_param.h 236NMBCLUSTERS opt_param.h 237NSFBUFS opt_param.h 238VM_BCACHE_SIZE_MAX opt_param.h 239VM_SWZONE_SIZE_MAX opt_param.h 240MAXUSERS 241DFLDSIZ opt_param.h 242MAXDSIZ opt_param.h 243MAXSSIZ opt_param.h 244 245# Generic SCSI options. 246CAM_MAX_HIGHPOWER opt_cam.h 247CAMDEBUG opt_cam.h 248CAM_DEBUG_DELAY opt_cam.h 249CAM_DEBUG_BUS opt_cam.h 250CAM_DEBUG_TARGET opt_cam.h 251CAM_DEBUG_LUN opt_cam.h 252CAM_DEBUG_FLAGS opt_cam.h 253CAM_NEW_TRAN_CODE opt_cam.h 254SCSI_DELAY opt_scsi.h 255SCSI_NO_SENSE_STRINGS opt_scsi.h 256SCSI_NO_OP_STRINGS opt_scsi.h 257 258 259 260# Options used only in cam/scsi/scsi_cd.c 261CHANGER_MIN_BUSY_SECONDS opt_cd.h 262CHANGER_MAX_BUSY_SECONDS opt_cd.h 263 264# Options used only in cam/scsi/scsi_sa.c. 265SA_IO_TIMEOUT opt_sa.h 266SA_SPACE_TIMEOUT opt_sa.h 267SA_REWIND_TIMEOUT opt_sa.h 268SA_ERASE_TIMEOUT opt_sa.h 269SA_1FM_AT_EOD opt_sa.h 270 271# Options used only in cam/scsi/scsi_pt.c 272SCSI_PT_DEFAULT_TIMEOUT opt_pt.h 273 274# Options used only in cam/scsi/scsi_ses.c 275SES_ENABLE_PASSTHROUGH opt_ses.h 276 277# Options used in dev/sym/ (Symbios SCSI driver). 278SYM_SETUP_LP_PROBE_MAP opt_sym.h #-Low Priority Probe Map (bits) 279 # Allows the ncr to take precedence 280 # 1 (1<<0) -> 810a, 860 281 # 2 (1<<1) -> 825a, 875, 885, 895 282 # 4 (1<<2) -> 895a, 896, 1510d 283SYM_SETUP_SCSI_DIFF opt_sym.h #-HVD support for 825a, 875, 885 284 # disabled:0 (default), enabled:1 285SYM_SETUP_PCI_PARITY opt_sym.h #-PCI parity checking 286 # disabled:0, enabled:1 (default) 287SYM_SETUP_MAX_LUN opt_sym.h #-Number of LUNs supported 288 # default:8, range:[1..64] 289 290# Options used only in pci/ncr.c 291SCSI_NCR_DEBUG opt_ncr.h 292SCSI_NCR_MAX_SYNC opt_ncr.h 293SCSI_NCR_MAX_WIDE opt_ncr.h 294SCSI_NCR_MYADDR opt_ncr.h 295 296# Options used only in dev/isp/* 297ISP_TARGET_MODE opt_isp.h 298ISP_FW_CRASH_DUMP opt_isp.h 299 300# Options used in the 'ata' ATA/ATAPI driver 301ATA_STATIC_ID opt_ata.h 302ATA_NOPCI opt_ata.h 303DEV_ATADISK opt_ata.h 304DEV_ATAPICD opt_ata.h 305DEV_ATAPIST opt_ata.h 306DEV_ATAPIFD opt_ata.h 307DEV_ATAPICAM opt_ata.h 308ATA_DEBUG opt_ata.h 309ATAPI_DEBUG opt_ata.h 310ACD_DEBUG opt_ata.h 311AST_DEBUG opt_ata.h 312 313# Net stuff. 314ACCEPT_FILTER_DATA 315ACCEPT_FILTER_HTTP 316BOOTP opt_bootp.h 317BOOTP_COMPAT opt_bootp.h 318BOOTP_NFSROOT opt_bootp.h 319BOOTP_NFSV3 opt_bootp.h 320BOOTP_WIRED_TO opt_bootp.h 321BRIDGE opt_bdg.h 322ETHER_II opt_ef.h 323ETHER_8023 opt_ef.h 324ETHER_8022 opt_ef.h 325ETHER_SNAP opt_ef.h 326MROUTING opt_mrouting.h 327INET opt_inet.h 328INET6 opt_inet6.h 329IPSEC opt_ipsec.h 330IPSEC_ESP opt_ipsec.h 331IPSEC_DEBUG opt_ipsec.h 332IPSEC_FILTERGIF opt_ipsec.h 333FAST_IPSEC opt_ipsec.h 334IPDIVERT 335DUMMYNET opt_ipdn.h 336IPFILTER opt_ipfilter.h 337IPFILTER_LOG opt_ipfilter.h 338IPFILTER_DEFAULT_BLOCK opt_ipfilter.h 339PFIL_HOOKS opt_pfil_hooks.h 340IPFIREWALL opt_ipfw.h 341IPFIREWALL_VERBOSE opt_ipfw.h 342IPFIREWALL_VERBOSE_LIMIT opt_ipfw.h 343IPFIREWALL_DEFAULT_TO_ACCEPT opt_ipfw.h 344IPFIREWALL_FORWARD opt_ipfw.h 345IPV6FIREWALL opt_ip6fw.h 346IPV6FIREWALL_VERBOSE opt_ip6fw.h 347IPV6FIREWALL_VERBOSE_LIMIT opt_ip6fw.h 348IPV6FIREWALL_DEFAULT_TO_ACCEPT opt_ip6fw.h 349IPSTEALTH 350IPX opt_ipx.h 351IPXIP opt_ipx.h 352LIBMCHAIN 353NCP opt_ncp.h 354NETATALK opt_atalk.h 355PPP_BSDCOMP opt_ppp.h 356PPP_DEFLATE opt_ppp.h 357PPP_FILTER opt_ppp.h 358RANDOM_IP_ID 359SLIP_IFF_OPTS opt_slip.h 360TCPDEBUG 361TCP_DROP_SYNFIN opt_tcp_input.h 362XBONEHACK 363MBUF_FRAG_TEST opt_mbuf_frag_test.h 364 365# Netgraph(4). Use option NETGRAPH to enable the base netgraph code. 366# Each netgraph node type can be either be compiled into the kernel 367# or loaded dynamically. To get the former, include the corresponding 368# option below. Each type has its own man page, e.g. ng_async(4). 369NETGRAPH 370NETGRAPH_ASYNC opt_netgraph.h 371NETGRAPH_BPF opt_netgraph.h 372NETGRAPH_BRIDGE opt_netgraph.h 373NETGRAPH_CISCO opt_netgraph.h 374NETGRAPH_ECHO opt_netgraph.h 375NETGRAPH_ETHER opt_netgraph.h 376NETGRAPH_FRAME_RELAY opt_netgraph.h 377NETGRAPH_GIF opt_netgraph.h 378NETGRAPH_GIF_DEMUX opt_netgraph.h 379NETGRAPH_HOLE opt_netgraph.h 380NETGRAPH_IFACE opt_netgraph.h 381NETGRAPH_IP_INPUT opt_netgraph.h 382NETGRAPH_KSOCKET opt_netgraph.h 383NETGRAPH_LMI opt_netgraph.h 384NETGRAPH_L2TP opt_netgraph.h 385# MPPC compression requires proprietary files (not included) 386NETGRAPH_MPPC_COMPRESSION opt_netgraph.h 387NETGRAPH_MPPC_ENCRYPTION opt_netgraph.h 388NETGRAPH_ONE2MANY opt_netgraph.h 389NETGRAPH_PPP opt_netgraph.h 390NETGRAPH_PPPOE opt_netgraph.h 391NETGRAPH_PPTPGRE opt_netgraph.h 392NETGRAPH_RFC1490 opt_netgraph.h 393NETGRAPH_SOCKET opt_netgraph.h 394NETGRAPH_SPLIT opt_netgraph.h 395NETGRAPH_TEE opt_netgraph.h 396NETGRAPH_TTY opt_netgraph.h 397NETGRAPH_UI opt_netgraph.h 398NETGRAPH_VJC opt_netgraph.h 399 400# DRM options 401DRM_LINUX opt_drm.h 402DRM_DEBUG opt_drm.h 403 404 405ZERO_COPY_SOCKETS opt_zero.h 406TI_PRIVATE_JUMBOS opt_ti.h 407TI_JUMBO_HDRSPLIT opt_ti.h 408 409# ATM (HARP version) 410ATM_CORE opt_atm.h 411ATM_IP opt_atm.h 412ATM_SIGPVC opt_atm.h 413ATM_SPANS opt_atm.h 414ATM_UNI opt_atm.h 415 416# XXX Conflict: # of devices vs network protocol (Native ATM). 417# This makes "atm.h" unusable. 418NATM opt_natm.h 419 420DPT_ALLOW_MEMIO opt_dpt.h # Allow PCI devices to use memory 421 # mapped I/O 422# DPT driver debug flags 423DPT_MEASURE_PERFORMANCE opt_dpt.h 424DPT_HANDLE_TIMEOUTS opt_dpt.h 425DPT_TIMEOUT_FACTOR opt_dpt.h 426DPT_LOST_IRQ opt_dpt.h 427DPT_RESET_HBA opt_dpt.h 428 429# Adaptec ASR and DPT V/VI controller options 430ASR_MEASURE_PERFORMANCE opt_asr.h 431 432# Misc debug flags. Most of these should probably be replaced with 433# 'DEBUG', and then let people recompile just the interesting modules 434# with 'make CC="cc -DDEBUG"'. 435CLUSTERDEBUG opt_debug_cluster.h 436DEBUG_1284 opt_ppb_1284.h 437VP0_DEBUG opt_vpo.h 438LPT_DEBUG opt_lpt.h 439PLIP_DEBUG opt_plip.h 440LOCKF_DEBUG opt_debug_lockf.h 441NPX_DEBUG opt_debug_npx.h 442NETATALKDEBUG opt_atalk.h 443SI_DEBUG opt_debug_si.h 444 445# Fb options 446FB_DEBUG opt_fb.h 447FB_INSTALL_CDEV opt_fb.h 448 449# ppbus related options 450PERIPH_1284 opt_ppb_1284.h 451DONTPROBE_1284 opt_ppb_1284.h 452 453# smbus related options 454ENABLE_ALART opt_intpm.h 455 456# These cause changes all over the kernel 457BLKDEV_IOSIZE opt_global.h 458DEBUG opt_global.h 459DEBUG_LOCKS opt_global.h 460DEBUG_VFS_LOCKS opt_global.h 461LOOKUP_SHARED opt_global.h 462DIAGNOSTIC opt_global.h 463INVARIANT_SUPPORT opt_global.h 464INVARIANTS opt_global.h 465MCLSHIFT opt_global.h 466MSIZE opt_global.h 467REGRESSION opt_global.h 468RESTARTABLE_PANICS opt_global.h 469VFS_BIO_DEBUG opt_global.h 470 471# These are VM related options 472VM_KMEM_SIZE opt_vm.h 473VM_KMEM_SIZE_SCALE opt_vm.h 474VM_KMEM_SIZE_MAX opt_vm.h 475NO_SWAPPING opt_vm.h 476MALLOC_MAKE_FAILURES opt_vm.h 477MALLOC_PROFILE opt_vm.h 478PQ_NOOPT opt_vmpage.h 479PQ_NORMALCACHE opt_vmpage.h 480PQ_MEDIUMCACHE opt_vmpage.h 481PQ_LARGECACHE opt_vmpage.h 482PQ_HUGECACHE opt_vmpage.h 483PQ_CACHESIZE opt_vmpage.h 484 485# Standard SMP options 486SMP opt_global.h 487 488# Size of the kernel message buffer 489MSGBUF_SIZE opt_msgbuf.h 490 491# NFS options 492NFS_MINATTRTIMO opt_nfs.h 493NFS_MAXATTRTIMO opt_nfs.h 494NFS_MINDIRATTRTIMO opt_nfs.h 495NFS_MAXDIRATTRTIMO opt_nfs.h 496NFS_GATHERDELAY opt_nfs.h 497NFS_WDELAYHASHSIZ opt_nfs.h 498NFS_DEBUG opt_nfs.h 499 500# For the Bt848/Bt848A/Bt849/Bt878/Bt879 driver 501OVERRIDE_CARD opt_bktr.h 502OVERRIDE_TUNER opt_bktr.h 503OVERRIDE_DBX opt_bktr.h 504OVERRIDE_MSP opt_bktr.h 505BROOKTREE_SYSTEM_DEFAULT opt_bktr.h 506BROOKTREE_ALLOC_PAGES opt_bktr.h 507BKTR_OVERRIDE_CARD opt_bktr.h 508BKTR_OVERRIDE_TUNER opt_bktr.h 509BKTR_OVERRIDE_DBX opt_bktr.h 510BKTR_OVERRIDE_MSP opt_bktr.h 511BKTR_SYSTEM_DEFAULT opt_bktr.h 512BKTR_ALLOC_PAGES opt_bktr.h 513BKTR_USE_PLL opt_bktr.h 514BKTR_GPIO_ACCESS opt_bktr.h 515BKTR_NO_MSP_RESET opt_bktr.h 516BKTR_430_FX_MODE opt_bktr.h 517BKTR_SIS_VIA_MODE opt_bktr.h 518BKTR_USE_FREEBSD_SMBUS opt_bktr.h 519 520# meteor opt_meteor.h 521METEOR_ALLOC_PAGES opt_meteor.h 522METEOR_TEST_VIDEO opt_meteor.h 523METEOR_SYSTEM_DEFAULT opt_meteor.h 524METEOR_DEALLOC_PAGES opt_meteor.h 525METEOR_DEALLOC_ABOVE opt_meteor.h 526 527# options for serial support 528COM_ESP opt_sio.h 529COM_MULTIPORT opt_sio.h 530BREAK_TO_DEBUGGER opt_comconsole.h 531ALT_BREAK_TO_DEBUGGER opt_comconsole.h 532 533# options for bus/device framework 534BUS_DEBUG opt_bus.h 535 536# options for USB support 537UHCI_DEBUG opt_usb.h 538OHCI_DEBUG opt_usb.h 539USB_DEBUG opt_usb.h 540UGEN_DEBUG opt_usb.h 541UHID_DEBUG opt_usb.h 542UHUB_DEBUG opt_usb.h 543UKBD_DEBUG opt_usb.h 544ULPT_DEBUG opt_usb.h 545UMASS_DEBUG opt_usb.h 546UMS_DEBUG opt_usb.h 547URIO_DEBUG opt_usb.h 548UKBD_DFLT_KEYMAP opt_ukbd.h 549UVSCOM_DEFAULT_OPKTSIZE opt_uvscom.h 550 551# Vinum options 552VINUMDEBUG opt_vinum.h 553VINUM_AUTOSTART opt_vinum.h 554 555# Embedded system options 556INIT_PATH opt_init_path.h 557 558ROOTDEVNAME opt_rootdevname.h 559 560FDC_DEBUG opt_fdc.h 561PCFCLOCK_VERBOSE opt_pcfclock.h 562PCFCLOCK_MAX_RETRIES opt_pcfclock.h 563 564# RAIDframe options 565RAID_AUTOCONFIG opt_raid.h 566RAID_DEBUG opt_raid.h 567TDFX_LINUX opt_tdfx.h 568 569KTR opt_global.h 570KTR_ALQ opt_ktr.h 571KTR_MASK opt_ktr.h 572KTR_CPUMASK opt_ktr.h 573KTR_COMPILE opt_global.h 574KTR_ENTRIES opt_global.h 575KTR_VERBOSE opt_ktr.h 576MUTEX_DEBUG opt_global.h 577WITNESS opt_global.h 578WITNESS_DDB opt_witness.h 579WITNESS_SKIPSPIN opt_witness.h 580 581# options for ACPI support 582ACPI_DEBUG opt_acpi.h 583ACPI_NO_SEMAPHORES opt_acpi.h 584ACPI_MAX_THREADS opt_acpi.h 585 586# options for DEVFS, see sys/fs/devfs/devfs.h 587NDEVFSINO opt_devfs.h 588NDEVFSOVERFLOW opt_devfs.h 589 590# various 'device presence' options. 591DEV_ISA opt_isa.h 592DEV_MCA opt_mca.h 593DEV_BPF opt_bpf.h 594 595# ed driver 596ED_NO_MIIBUS opt_ed.h 597 598# wi driver 599WI_SYMBOL_FIRMWARE opt_wi.h 600 601# Polling device handling 602DEVICE_POLLING opt_global.h 603 604# Mutex profiling 605MUTEX_PROFILING opt_global.h 606 607# options for ubsec driver 608UBSEC_DEBUG opt_ubsec.h 609UBSEC_RNDTEST opt_ubsec.h 610 611# options for hifn driver 612HIFN_DEBUG opt_hifn.h 613HIFN_RNDTEST opt_hifn.h 614