e1000_82571.c revision 185353
1/****************************************************************************** 2 3 Copyright (c) 2001-2008, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32******************************************************************************/ 33/*$FreeBSD: head/sys/dev/e1000/e1000_82571.c 185353 2008-11-26 23:57:23Z jfv $*/ 34 35/* 36 * 82571EB Gigabit Ethernet Controller 37 * 82571EB Gigabit Ethernet Controller (Copper) 38 * 82571EB Gigabit Ethernet Controller (Fiber) 39 * 82571EB Dual Port Gigabit Mezzanine Adapter 40 * 82571EB Quad Port Gigabit Mezzanine Adapter 41 * 82571PT Gigabit PT Quad Port Server ExpressModule 42 * 82572EI Gigabit Ethernet Controller (Copper) 43 * 82572EI Gigabit Ethernet Controller (Fiber) 44 * 82572EI Gigabit Ethernet Controller 45 * 82573V Gigabit Ethernet Controller (Copper) 46 * 82573E Gigabit Ethernet Controller (Copper) 47 * 82573L Gigabit Ethernet Controller 48 * 82574L Gigabit Network Connection 49 */ 50 51#include "e1000_api.h" 52 53static s32 e1000_init_phy_params_82571(struct e1000_hw *hw); 54static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw); 55static s32 e1000_init_mac_params_82571(struct e1000_hw *hw); 56static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw); 57static void e1000_release_nvm_82571(struct e1000_hw *hw); 58static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, 59 u16 words, u16 *data); 60static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw); 61static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw); 62static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw); 63static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, 64 bool active); 65static s32 e1000_reset_hw_82571(struct e1000_hw *hw); 66static s32 e1000_init_hw_82571(struct e1000_hw *hw); 67static void e1000_clear_vfta_82571(struct e1000_hw *hw); 68static bool e1000_check_mng_mode_82574(struct e1000_hw *hw); 69static s32 e1000_led_on_82574(struct e1000_hw *hw); 70static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw, 71 u8 *mc_addr_list, u32 mc_addr_count, 72 u32 rar_used_count, u32 rar_count); 73static s32 e1000_setup_link_82571(struct e1000_hw *hw); 74static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw); 75static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw); 76static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data); 77static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw); 78static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw); 79static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw); 80static s32 e1000_get_phy_id_82571(struct e1000_hw *hw); 81static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw); 82static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw); 83static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, 84 u16 words, u16 *data); 85static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw); 86static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw); 87 88/** 89 * e1000_init_phy_params_82571 - Init PHY func ptrs. 90 * @hw: pointer to the HW structure 91 **/ 92static s32 e1000_init_phy_params_82571(struct e1000_hw *hw) 93{ 94 struct e1000_phy_info *phy = &hw->phy; 95 s32 ret_val = E1000_SUCCESS; 96 97 DEBUGFUNC("e1000_init_phy_params_82571"); 98 99 if (hw->phy.media_type != e1000_media_type_copper) { 100 phy->type = e1000_phy_none; 101 goto out; 102 } 103 104 phy->addr = 1; 105 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 106 phy->reset_delay_us = 100; 107 108 phy->ops.acquire = e1000_get_hw_semaphore_82571; 109 phy->ops.check_polarity = e1000_check_polarity_igp; 110 phy->ops.check_reset_block = e1000_check_reset_block_generic; 111 phy->ops.release = e1000_put_hw_semaphore_82571; 112 phy->ops.reset = e1000_phy_hw_reset_generic; 113 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82571; 114 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; 115 phy->ops.power_up = e1000_power_up_phy_copper; 116 phy->ops.power_down = e1000_power_down_phy_copper_82571; 117 118 switch (hw->mac.type) { 119 case e1000_82571: 120 case e1000_82572: 121 phy->type = e1000_phy_igp_2; 122 phy->ops.get_cfg_done = e1000_get_cfg_done_82571; 123 phy->ops.get_info = e1000_get_phy_info_igp; 124 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; 125 phy->ops.get_cable_length = e1000_get_cable_length_igp_2; 126 phy->ops.read_reg = e1000_read_phy_reg_igp; 127 phy->ops.write_reg = e1000_write_phy_reg_igp; 128 129 /* This uses above function pointers */ 130 ret_val = e1000_get_phy_id_82571(hw); 131 132 /* Verify PHY ID */ 133 if (phy->id != IGP01E1000_I_PHY_ID) { 134 ret_val = -E1000_ERR_PHY; 135 goto out; 136 } 137 break; 138 case e1000_82573: 139 phy->type = e1000_phy_m88; 140 phy->ops.get_cfg_done = e1000_get_cfg_done_generic; 141 phy->ops.get_info = e1000_get_phy_info_m88; 142 phy->ops.commit = e1000_phy_sw_reset_generic; 143 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; 144 phy->ops.get_cable_length = e1000_get_cable_length_m88; 145 phy->ops.read_reg = e1000_read_phy_reg_m88; 146 phy->ops.write_reg = e1000_write_phy_reg_m88; 147 148 /* This uses above function pointers */ 149 ret_val = e1000_get_phy_id_82571(hw); 150 151 /* Verify PHY ID */ 152 if (phy->id != M88E1111_I_PHY_ID) { 153 ret_val = -E1000_ERR_PHY; 154 DEBUGOUT1("PHY ID unknown: type = 0x%08x\n", phy->id); 155 goto out; 156 } 157 break; 158 case e1000_82574: 159 phy->type = e1000_phy_bm; 160 phy->ops.get_cfg_done = e1000_get_cfg_done_generic; 161 phy->ops.get_info = e1000_get_phy_info_m88; 162 phy->ops.commit = e1000_phy_sw_reset_generic; 163 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; 164 phy->ops.get_cable_length = e1000_get_cable_length_m88; 165 phy->ops.read_reg = e1000_read_phy_reg_bm2; 166 phy->ops.write_reg = e1000_write_phy_reg_bm2; 167 168 /* This uses above function pointers */ 169 ret_val = e1000_get_phy_id_82571(hw); 170 /* Verify PHY ID */ 171 if (phy->id != BME1000_E_PHY_ID_R2) { 172 ret_val = -E1000_ERR_PHY; 173 DEBUGOUT1("PHY ID unknown: type = 0x%08x\n", phy->id); 174 goto out; 175 } 176 break; 177 default: 178 ret_val = -E1000_ERR_PHY; 179 goto out; 180 break; 181 } 182 183out: 184 return ret_val; 185} 186 187/** 188 * e1000_init_nvm_params_82571 - Init NVM func ptrs. 189 * @hw: pointer to the HW structure 190 **/ 191static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw) 192{ 193 struct e1000_nvm_info *nvm = &hw->nvm; 194 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 195 u16 size; 196 197 DEBUGFUNC("e1000_init_nvm_params_82571"); 198 199 nvm->opcode_bits = 8; 200 nvm->delay_usec = 1; 201 switch (nvm->override) { 202 case e1000_nvm_override_spi_large: 203 nvm->page_size = 32; 204 nvm->address_bits = 16; 205 break; 206 case e1000_nvm_override_spi_small: 207 nvm->page_size = 8; 208 nvm->address_bits = 8; 209 break; 210 default: 211 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; 212 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; 213 break; 214 } 215 216 switch (hw->mac.type) { 217 case e1000_82573: 218 case e1000_82574: 219 if (((eecd >> 15) & 0x3) == 0x3) { 220 nvm->type = e1000_nvm_flash_hw; 221 nvm->word_size = 2048; 222 /* 223 * Autonomous Flash update bit must be cleared due 224 * to Flash update issue. 225 */ 226 eecd &= ~E1000_EECD_AUPDEN; 227 E1000_WRITE_REG(hw, E1000_EECD, eecd); 228 break; 229 } 230 /* Fall Through */ 231 default: 232 nvm->type = e1000_nvm_eeprom_spi; 233 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> 234 E1000_EECD_SIZE_EX_SHIFT); 235 /* 236 * Added to a constant, "size" becomes the left-shift value 237 * for setting word_size. 238 */ 239 size += NVM_WORD_SIZE_BASE_SHIFT; 240 241 /* EEPROM access above 16k is unsupported */ 242 if (size > 14) 243 size = 14; 244 nvm->word_size = 1 << size; 245 break; 246 } 247 248 /* Function Pointers */ 249 nvm->ops.acquire = e1000_acquire_nvm_82571; 250 nvm->ops.read = e1000_read_nvm_eerd; 251 nvm->ops.release = e1000_release_nvm_82571; 252 nvm->ops.update = e1000_update_nvm_checksum_82571; 253 nvm->ops.validate = e1000_validate_nvm_checksum_82571; 254 nvm->ops.valid_led_default = e1000_valid_led_default_82571; 255 nvm->ops.write = e1000_write_nvm_82571; 256 257 return E1000_SUCCESS; 258} 259 260/** 261 * e1000_init_mac_params_82571 - Init MAC func ptrs. 262 * @hw: pointer to the HW structure 263 **/ 264static s32 e1000_init_mac_params_82571(struct e1000_hw *hw) 265{ 266 struct e1000_mac_info *mac = &hw->mac; 267 s32 ret_val = E1000_SUCCESS; 268 269 DEBUGFUNC("e1000_init_mac_params_82571"); 270 271 /* Set media type */ 272 switch (hw->device_id) { 273 case E1000_DEV_ID_82571EB_FIBER: 274 case E1000_DEV_ID_82572EI_FIBER: 275 case E1000_DEV_ID_82571EB_QUAD_FIBER: 276 hw->phy.media_type = e1000_media_type_fiber; 277 break; 278 case E1000_DEV_ID_82571EB_SERDES: 279 case E1000_DEV_ID_82571EB_SERDES_DUAL: 280 case E1000_DEV_ID_82571EB_SERDES_QUAD: 281 case E1000_DEV_ID_82572EI_SERDES: 282 hw->phy.media_type = e1000_media_type_internal_serdes; 283 break; 284 default: 285 hw->phy.media_type = e1000_media_type_copper; 286 break; 287 } 288 289 /* Set mta register count */ 290 mac->mta_reg_count = 128; 291 /* Set rar entry count */ 292 mac->rar_entry_count = E1000_RAR_ENTRIES; 293 /* Set if part includes ASF firmware */ 294 mac->asf_firmware_present = TRUE; 295 /* Set if manageability features are enabled. */ 296 mac->arc_subsystem_valid = 297 (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) 298 ? TRUE : FALSE; 299 300 /* Function pointers */ 301 302 /* bus type/speed/width */ 303 mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; 304 /* function id */ 305 switch (hw->mac.type) { 306 case e1000_82573: 307 case e1000_82574: 308 mac->ops.set_lan_id = e1000_set_lan_id_single_port; 309 break; 310 default: 311 break; 312 } 313 /* reset */ 314 mac->ops.reset_hw = e1000_reset_hw_82571; 315 /* hw initialization */ 316 mac->ops.init_hw = e1000_init_hw_82571; 317 /* link setup */ 318 mac->ops.setup_link = e1000_setup_link_82571; 319 /* physical interface link setup */ 320 mac->ops.setup_physical_interface = 321 (hw->phy.media_type == e1000_media_type_copper) 322 ? e1000_setup_copper_link_82571 323 : e1000_setup_fiber_serdes_link_82571; 324 /* check for link */ 325 switch (hw->phy.media_type) { 326 case e1000_media_type_copper: 327 mac->ops.check_for_link = e1000_check_for_copper_link_generic; 328 break; 329 case e1000_media_type_fiber: 330 mac->ops.check_for_link = e1000_check_for_fiber_link_generic; 331 break; 332 case e1000_media_type_internal_serdes: 333 mac->ops.check_for_link = e1000_check_for_serdes_link_generic; 334 break; 335 default: 336 ret_val = -E1000_ERR_CONFIG; 337 goto out; 338 break; 339 } 340 /* check management mode */ 341 switch (hw->mac.type) { 342 case e1000_82574: 343 mac->ops.check_mng_mode = e1000_check_mng_mode_82574; 344 break; 345 default: 346 mac->ops.check_mng_mode = e1000_check_mng_mode_generic; 347 break; 348 } 349 /* multicast address update */ 350 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_82571; 351 /* writing VFTA */ 352 mac->ops.write_vfta = e1000_write_vfta_generic; 353 /* clearing VFTA */ 354 mac->ops.clear_vfta = e1000_clear_vfta_82571; 355 /* setting MTA */ 356 mac->ops.mta_set = e1000_mta_set_generic; 357 /* read mac address */ 358 mac->ops.read_mac_addr = e1000_read_mac_addr_82571; 359 /* blink LED */ 360 mac->ops.blink_led = e1000_blink_led_generic; 361 /* setup LED */ 362 mac->ops.setup_led = e1000_setup_led_generic; 363 /* cleanup LED */ 364 mac->ops.cleanup_led = e1000_cleanup_led_generic; 365 /* turn on/off LED */ 366 switch (hw->mac.type) { 367 case e1000_82574: 368 mac->ops.led_on = e1000_led_on_82574; 369 break; 370 default: 371 mac->ops.led_on = e1000_led_on_generic; 372 break; 373 } 374 mac->ops.led_off = e1000_led_off_generic; 375 /* clear hardware counters */ 376 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82571; 377 /* link info */ 378 mac->ops.get_link_up_info = 379 (hw->phy.media_type == e1000_media_type_copper) 380 ? e1000_get_speed_and_duplex_copper_generic 381 : e1000_get_speed_and_duplex_fiber_serdes_generic; 382 383out: 384 return ret_val; 385} 386 387/** 388 * e1000_init_function_pointers_82571 - Init func ptrs. 389 * @hw: pointer to the HW structure 390 * 391 * Called to initialize all function pointers and parameters. 392 **/ 393void e1000_init_function_pointers_82571(struct e1000_hw *hw) 394{ 395 DEBUGFUNC("e1000_init_function_pointers_82571"); 396 397 hw->mac.ops.init_params = e1000_init_mac_params_82571; 398 hw->nvm.ops.init_params = e1000_init_nvm_params_82571; 399 hw->phy.ops.init_params = e1000_init_phy_params_82571; 400} 401 402/** 403 * e1000_get_phy_id_82571 - Retrieve the PHY ID and revision 404 * @hw: pointer to the HW structure 405 * 406 * Reads the PHY registers and stores the PHY ID and possibly the PHY 407 * revision in the hardware structure. 408 **/ 409static s32 e1000_get_phy_id_82571(struct e1000_hw *hw) 410{ 411 struct e1000_phy_info *phy = &hw->phy; 412 s32 ret_val = E1000_SUCCESS; 413 u16 phy_id = 0; 414 415 DEBUGFUNC("e1000_get_phy_id_82571"); 416 417 switch (hw->mac.type) { 418 case e1000_82571: 419 case e1000_82572: 420 /* 421 * The 82571 firmware may still be configuring the PHY. 422 * In this case, we cannot access the PHY until the 423 * configuration is done. So we explicitly set the 424 * PHY ID. 425 */ 426 phy->id = IGP01E1000_I_PHY_ID; 427 break; 428 case e1000_82573: 429 ret_val = e1000_get_phy_id(hw); 430 break; 431 case e1000_82574: 432 ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id); 433 if (ret_val) 434 goto out; 435 436 phy->id = (u32)(phy_id << 16); 437 usec_delay(20); 438 ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id); 439 if (ret_val) 440 goto out; 441 442 phy->id |= (u32)(phy_id); 443 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); 444 break; 445 default: 446 ret_val = -E1000_ERR_PHY; 447 break; 448 } 449 450out: 451 return ret_val; 452} 453 454/** 455 * e1000_get_hw_semaphore_82571 - Acquire hardware semaphore 456 * @hw: pointer to the HW structure 457 * 458 * Acquire the HW semaphore to access the PHY or NVM 459 **/ 460static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw) 461{ 462 u32 swsm; 463 s32 ret_val = E1000_SUCCESS; 464 s32 timeout = hw->nvm.word_size + 1; 465 s32 i = 0; 466 467 DEBUGFUNC("e1000_get_hw_semaphore_82571"); 468 469 /* Get the FW semaphore. */ 470 for (i = 0; i < timeout; i++) { 471 swsm = E1000_READ_REG(hw, E1000_SWSM); 472 E1000_WRITE_REG(hw, E1000_SWSM, swsm | E1000_SWSM_SWESMBI); 473 474 /* Semaphore acquired if bit latched */ 475 if (E1000_READ_REG(hw, E1000_SWSM) & E1000_SWSM_SWESMBI) 476 break; 477 478 usec_delay(50); 479 } 480 481 if (i == timeout) { 482 /* Release semaphores */ 483 e1000_put_hw_semaphore_generic(hw); 484 DEBUGOUT("Driver can't access the NVM\n"); 485 ret_val = -E1000_ERR_NVM; 486 goto out; 487 } 488 489out: 490 return ret_val; 491} 492 493/** 494 * e1000_put_hw_semaphore_82571 - Release hardware semaphore 495 * @hw: pointer to the HW structure 496 * 497 * Release hardware semaphore used to access the PHY or NVM 498 **/ 499static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw) 500{ 501 u32 swsm; 502 503 DEBUGFUNC("e1000_put_hw_semaphore_82571"); 504 505 swsm = E1000_READ_REG(hw, E1000_SWSM); 506 507 swsm &= ~E1000_SWSM_SWESMBI; 508 509 E1000_WRITE_REG(hw, E1000_SWSM, swsm); 510} 511 512/** 513 * e1000_acquire_nvm_82571 - Request for access to the EEPROM 514 * @hw: pointer to the HW structure 515 * 516 * To gain access to the EEPROM, first we must obtain a hardware semaphore. 517 * Then for non-82573 hardware, set the EEPROM access request bit and wait 518 * for EEPROM access grant bit. If the access grant bit is not set, release 519 * hardware semaphore. 520 **/ 521static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw) 522{ 523 s32 ret_val; 524 525 DEBUGFUNC("e1000_acquire_nvm_82571"); 526 527 ret_val = e1000_get_hw_semaphore_82571(hw); 528 if (ret_val) 529 goto out; 530 531 if (hw->mac.type != e1000_82573 && hw->mac.type != e1000_82574) 532 ret_val = e1000_acquire_nvm_generic(hw); 533 534 if (ret_val) 535 e1000_put_hw_semaphore_82571(hw); 536 537out: 538 return ret_val; 539} 540 541/** 542 * e1000_release_nvm_82571 - Release exclusive access to EEPROM 543 * @hw: pointer to the HW structure 544 * 545 * Stop any current commands to the EEPROM and clear the EEPROM request bit. 546 **/ 547static void e1000_release_nvm_82571(struct e1000_hw *hw) 548{ 549 DEBUGFUNC("e1000_release_nvm_82571"); 550 551 e1000_release_nvm_generic(hw); 552 e1000_put_hw_semaphore_82571(hw); 553} 554 555/** 556 * e1000_write_nvm_82571 - Write to EEPROM using appropriate interface 557 * @hw: pointer to the HW structure 558 * @offset: offset within the EEPROM to be written to 559 * @words: number of words to write 560 * @data: 16 bit word(s) to be written to the EEPROM 561 * 562 * For non-82573 silicon, write data to EEPROM at offset using SPI interface. 563 * 564 * If e1000_update_nvm_checksum is not called after this function, the 565 * EEPROM will most likely contain an invalid checksum. 566 **/ 567static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words, 568 u16 *data) 569{ 570 s32 ret_val = E1000_SUCCESS; 571 572 DEBUGFUNC("e1000_write_nvm_82571"); 573 574 switch (hw->mac.type) { 575 case e1000_82573: 576 case e1000_82574: 577 ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data); 578 break; 579 case e1000_82571: 580 case e1000_82572: 581 ret_val = e1000_write_nvm_spi(hw, offset, words, data); 582 break; 583 default: 584 ret_val = -E1000_ERR_NVM; 585 break; 586 } 587 588 return ret_val; 589} 590 591/** 592 * e1000_update_nvm_checksum_82571 - Update EEPROM checksum 593 * @hw: pointer to the HW structure 594 * 595 * Updates the EEPROM checksum by reading/adding each word of the EEPROM 596 * up to the checksum. Then calculates the EEPROM checksum and writes the 597 * value to the EEPROM. 598 **/ 599static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw) 600{ 601 u32 eecd; 602 s32 ret_val; 603 u16 i; 604 605 DEBUGFUNC("e1000_update_nvm_checksum_82571"); 606 607 ret_val = e1000_update_nvm_checksum_generic(hw); 608 if (ret_val) 609 goto out; 610 611 /* 612 * If our nvm is an EEPROM, then we're done 613 * otherwise, commit the checksum to the flash NVM. 614 */ 615 if (hw->nvm.type != e1000_nvm_flash_hw) 616 goto out; 617 618 /* Check for pending operations. */ 619 for (i = 0; i < E1000_FLASH_UPDATES; i++) { 620 msec_delay(1); 621 if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_FLUPD) == 0) 622 break; 623 } 624 625 if (i == E1000_FLASH_UPDATES) { 626 ret_val = -E1000_ERR_NVM; 627 goto out; 628 } 629 630 /* Reset the firmware if using STM opcode. */ 631 if ((E1000_READ_REG(hw, E1000_FLOP) & 0xFF00) == E1000_STM_OPCODE) { 632 /* 633 * The enabling of and the actual reset must be done 634 * in two write cycles. 635 */ 636 E1000_WRITE_REG(hw, E1000_HICR, E1000_HICR_FW_RESET_ENABLE); 637 E1000_WRITE_FLUSH(hw); 638 E1000_WRITE_REG(hw, E1000_HICR, E1000_HICR_FW_RESET); 639 } 640 641 /* Commit the write to flash */ 642 eecd = E1000_READ_REG(hw, E1000_EECD) | E1000_EECD_FLUPD; 643 E1000_WRITE_REG(hw, E1000_EECD, eecd); 644 645 for (i = 0; i < E1000_FLASH_UPDATES; i++) { 646 msec_delay(1); 647 if ((E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_FLUPD) == 0) 648 break; 649 } 650 651 if (i == E1000_FLASH_UPDATES) { 652 ret_val = -E1000_ERR_NVM; 653 goto out; 654 } 655 656out: 657 return ret_val; 658} 659 660/** 661 * e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum 662 * @hw: pointer to the HW structure 663 * 664 * Calculates the EEPROM checksum by reading/adding each word of the EEPROM 665 * and then verifies that the sum of the EEPROM is equal to 0xBABA. 666 **/ 667static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw) 668{ 669 DEBUGFUNC("e1000_validate_nvm_checksum_82571"); 670 671 if (hw->nvm.type == e1000_nvm_flash_hw) 672 e1000_fix_nvm_checksum_82571(hw); 673 674 return e1000_validate_nvm_checksum_generic(hw); 675} 676 677/** 678 * e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon 679 * @hw: pointer to the HW structure 680 * @offset: offset within the EEPROM to be written to 681 * @words: number of words to write 682 * @data: 16 bit word(s) to be written to the EEPROM 683 * 684 * After checking for invalid values, poll the EEPROM to ensure the previous 685 * command has completed before trying to write the next word. After write 686 * poll for completion. 687 * 688 * If e1000_update_nvm_checksum is not called after this function, the 689 * EEPROM will most likely contain an invalid checksum. 690 **/ 691static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, 692 u16 words, u16 *data) 693{ 694 struct e1000_nvm_info *nvm = &hw->nvm; 695 u32 i, eewr = 0; 696 s32 ret_val = 0; 697 698 DEBUGFUNC("e1000_write_nvm_eewr_82571"); 699 700 /* 701 * A check for invalid values: offset too large, too many words, 702 * and not enough words. 703 */ 704 if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || 705 (words == 0)) { 706 DEBUGOUT("nvm parameter(s) out of bounds\n"); 707 ret_val = -E1000_ERR_NVM; 708 goto out; 709 } 710 711 for (i = 0; i < words; i++) { 712 eewr = (data[i] << E1000_NVM_RW_REG_DATA) | 713 ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) | 714 E1000_NVM_RW_REG_START; 715 716 ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); 717 if (ret_val) 718 break; 719 720 E1000_WRITE_REG(hw, E1000_EEWR, eewr); 721 722 ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); 723 if (ret_val) 724 break; 725 } 726 727out: 728 return ret_val; 729} 730 731/** 732 * e1000_get_cfg_done_82571 - Poll for configuration done 733 * @hw: pointer to the HW structure 734 * 735 * Reads the management control register for the config done bit to be set. 736 **/ 737static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw) 738{ 739 s32 timeout = PHY_CFG_TIMEOUT; 740 s32 ret_val = E1000_SUCCESS; 741 742 DEBUGFUNC("e1000_get_cfg_done_82571"); 743 744 while (timeout) { 745 if (E1000_READ_REG(hw, E1000_EEMNGCTL) & E1000_NVM_CFG_DONE_PORT_0) 746 break; 747 msec_delay(1); 748 timeout--; 749 } 750 if (!timeout) { 751 DEBUGOUT("MNG configuration cycle has not completed.\n"); 752 ret_val = -E1000_ERR_RESET; 753 goto out; 754 } 755 756out: 757 return ret_val; 758} 759 760/** 761 * e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state 762 * @hw: pointer to the HW structure 763 * @active: TRUE to enable LPLU, FALSE to disable 764 * 765 * Sets the LPLU D0 state according to the active flag. When activating LPLU 766 * this function also disables smart speed and vice versa. LPLU will not be 767 * activated unless the device autonegotiation advertisement meets standards 768 * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function 769 * pointer entry point only called by PHY setup routines. 770 **/ 771static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active) 772{ 773 struct e1000_phy_info *phy = &hw->phy; 774 s32 ret_val = E1000_SUCCESS; 775 u16 data; 776 777 DEBUGFUNC("e1000_set_d0_lplu_state_82571"); 778 779 if (!(phy->ops.read_reg)) 780 goto out; 781 782 ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); 783 if (ret_val) 784 goto out; 785 786 if (active) { 787 data |= IGP02E1000_PM_D0_LPLU; 788 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 789 data); 790 if (ret_val) 791 goto out; 792 793 /* When LPLU is enabled, we should disable SmartSpeed */ 794 ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 795 &data); 796 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 797 ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 798 data); 799 if (ret_val) 800 goto out; 801 } else { 802 data &= ~IGP02E1000_PM_D0_LPLU; 803 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 804 data); 805 /* 806 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 807 * during Dx states where the power conservation is most 808 * important. During driver activity we should enable 809 * SmartSpeed, so performance is maintained. 810 */ 811 if (phy->smart_speed == e1000_smart_speed_on) { 812 ret_val = phy->ops.read_reg(hw, 813 IGP01E1000_PHY_PORT_CONFIG, 814 &data); 815 if (ret_val) 816 goto out; 817 818 data |= IGP01E1000_PSCFR_SMART_SPEED; 819 ret_val = phy->ops.write_reg(hw, 820 IGP01E1000_PHY_PORT_CONFIG, 821 data); 822 if (ret_val) 823 goto out; 824 } else if (phy->smart_speed == e1000_smart_speed_off) { 825 ret_val = phy->ops.read_reg(hw, 826 IGP01E1000_PHY_PORT_CONFIG, 827 &data); 828 if (ret_val) 829 goto out; 830 831 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 832 ret_val = phy->ops.write_reg(hw, 833 IGP01E1000_PHY_PORT_CONFIG, 834 data); 835 if (ret_val) 836 goto out; 837 } 838 } 839 840out: 841 return ret_val; 842} 843 844/** 845 * e1000_reset_hw_82571 - Reset hardware 846 * @hw: pointer to the HW structure 847 * 848 * This resets the hardware into a known state. 849 **/ 850static s32 e1000_reset_hw_82571(struct e1000_hw *hw) 851{ 852 u32 ctrl, extcnf_ctrl, ctrl_ext, icr; 853 s32 ret_val; 854 u16 i = 0; 855 856 DEBUGFUNC("e1000_reset_hw_82571"); 857 858 /* 859 * Prevent the PCI-E bus from sticking if there is no TLP connection 860 * on the last TLP read/write transaction when MAC is reset. 861 */ 862 ret_val = e1000_disable_pcie_master_generic(hw); 863 if (ret_val) 864 DEBUGOUT("PCI-E Master disable polling has failed.\n"); 865 866 DEBUGOUT("Masking off all interrupts\n"); 867 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 868 869 E1000_WRITE_REG(hw, E1000_RCTL, 0); 870 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 871 E1000_WRITE_FLUSH(hw); 872 873 msec_delay(10); 874 875 /* 876 * Must acquire the MDIO ownership before MAC reset. 877 * Ownership defaults to firmware after a reset. 878 */ 879 if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { 880 extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); 881 extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; 882 883 do { 884 E1000_WRITE_REG(hw, E1000_EXTCNF_CTRL, extcnf_ctrl); 885 extcnf_ctrl = E1000_READ_REG(hw, E1000_EXTCNF_CTRL); 886 887 if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) 888 break; 889 890 extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; 891 892 msec_delay(2); 893 i++; 894 } while (i < MDIO_OWNERSHIP_TIMEOUT); 895 } 896 897 ctrl = E1000_READ_REG(hw, E1000_CTRL); 898 899 DEBUGOUT("Issuing a global reset to MAC\n"); 900 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 901 902 if (hw->nvm.type == e1000_nvm_flash_hw) { 903 usec_delay(10); 904 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 905 ctrl_ext |= E1000_CTRL_EXT_EE_RST; 906 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 907 E1000_WRITE_FLUSH(hw); 908 } 909 910 ret_val = e1000_get_auto_rd_done_generic(hw); 911 if (ret_val) 912 /* We don't want to continue accessing MAC registers. */ 913 goto out; 914 915 /* 916 * Phy configuration from NVM just starts after EECD_AUTO_RD is set. 917 * Need to wait for Phy configuration completion before accessing 918 * NVM and Phy. 919 */ 920 if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) 921 msec_delay(25); 922 923 /* Clear any pending interrupt events. */ 924 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 925 icr = E1000_READ_REG(hw, E1000_ICR); 926 927 if (!(e1000_check_alt_mac_addr_generic(hw))) 928 e1000_set_laa_state_82571(hw, TRUE); 929 930out: 931 return ret_val; 932} 933 934/** 935 * e1000_init_hw_82571 - Initialize hardware 936 * @hw: pointer to the HW structure 937 * 938 * This inits the hardware readying it for operation. 939 **/ 940static s32 e1000_init_hw_82571(struct e1000_hw *hw) 941{ 942 struct e1000_mac_info *mac = &hw->mac; 943 u32 reg_data; 944 s32 ret_val; 945 u16 i, rar_count = mac->rar_entry_count; 946 947 DEBUGFUNC("e1000_init_hw_82571"); 948 949 e1000_initialize_hw_bits_82571(hw); 950 951 /* Initialize identification LED */ 952 ret_val = e1000_id_led_init_generic(hw); 953 if (ret_val) { 954 DEBUGOUT("Error initializing identification LED\n"); 955 /* This is not fatal and we should not stop init due to this */ 956 } 957 958 /* Disabling VLAN filtering */ 959 DEBUGOUT("Initializing the IEEE VLAN\n"); 960 mac->ops.clear_vfta(hw); 961 962 /* Setup the receive address. */ 963 /* 964 * If, however, a locally administered address was assigned to the 965 * 82571, we must reserve a RAR for it to work around an issue where 966 * resetting one port will reload the MAC on the other port. 967 */ 968 if (e1000_get_laa_state_82571(hw)) 969 rar_count--; 970 e1000_init_rx_addrs_generic(hw, rar_count); 971 972 /* Zero out the Multicast HASH table */ 973 DEBUGOUT("Zeroing the MTA\n"); 974 for (i = 0; i < mac->mta_reg_count; i++) 975 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 976 977 /* Setup link and flow control */ 978 ret_val = mac->ops.setup_link(hw); 979 980 /* Set the transmit descriptor write-back policy */ 981 reg_data = E1000_READ_REG(hw, E1000_TXDCTL(0)); 982 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | 983 E1000_TXDCTL_FULL_TX_DESC_WB | 984 E1000_TXDCTL_COUNT_DESC; 985 E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg_data); 986 987 /* ...for both queues. */ 988 if (mac->type != e1000_82573 && mac->type != e1000_82574) { 989 reg_data = E1000_READ_REG(hw, E1000_TXDCTL(1)); 990 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | 991 E1000_TXDCTL_FULL_TX_DESC_WB | 992 E1000_TXDCTL_COUNT_DESC; 993 E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg_data); 994 } else { 995 e1000_enable_tx_pkt_filtering_generic(hw); 996 reg_data = E1000_READ_REG(hw, E1000_GCR); 997 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; 998 E1000_WRITE_REG(hw, E1000_GCR, reg_data); 999 } 1000 1001 /* 1002 * Clear all of the statistics registers (clear on read). It is 1003 * important that we do this after we have tried to establish link 1004 * because the symbol error count will increment wildly if there 1005 * is no link. 1006 */ 1007 e1000_clear_hw_cntrs_82571(hw); 1008 1009 return ret_val; 1010} 1011 1012/** 1013 * e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits 1014 * @hw: pointer to the HW structure 1015 * 1016 * Initializes required hardware-dependent bits needed for normal operation. 1017 **/ 1018static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw) 1019{ 1020 u32 reg; 1021 1022 DEBUGFUNC("e1000_initialize_hw_bits_82571"); 1023 1024 /* Transmit Descriptor Control 0 */ 1025 reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); 1026 reg |= (1 << 22); 1027 E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); 1028 1029 /* Transmit Descriptor Control 1 */ 1030 reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); 1031 reg |= (1 << 22); 1032 E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); 1033 1034 /* Transmit Arbitration Control 0 */ 1035 reg = E1000_READ_REG(hw, E1000_TARC(0)); 1036 reg &= ~(0xF << 27); /* 30:27 */ 1037 switch (hw->mac.type) { 1038 case e1000_82571: 1039 case e1000_82572: 1040 reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26); 1041 break; 1042 default: 1043 break; 1044 } 1045 E1000_WRITE_REG(hw, E1000_TARC(0), reg); 1046 1047 /* Transmit Arbitration Control 1 */ 1048 reg = E1000_READ_REG(hw, E1000_TARC(1)); 1049 switch (hw->mac.type) { 1050 case e1000_82571: 1051 case e1000_82572: 1052 reg &= ~((1 << 29) | (1 << 30)); 1053 reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26); 1054 if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) 1055 reg &= ~(1 << 28); 1056 else 1057 reg |= (1 << 28); 1058 E1000_WRITE_REG(hw, E1000_TARC(1), reg); 1059 break; 1060 default: 1061 break; 1062 } 1063 1064 /* Device Control */ 1065 if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { 1066 reg = E1000_READ_REG(hw, E1000_CTRL); 1067 reg &= ~(1 << 29); 1068 E1000_WRITE_REG(hw, E1000_CTRL, reg); 1069 } 1070 1071 /* Extended Device Control */ 1072 if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { 1073 reg = E1000_READ_REG(hw, E1000_CTRL_EXT); 1074 reg &= ~(1 << 23); 1075 reg |= (1 << 22); 1076 E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); 1077 } 1078 1079 /* PCI-Ex Control Register */ 1080 if (hw->mac.type == e1000_82574) { 1081 reg = E1000_READ_REG(hw, E1000_GCR); 1082 reg |= (1 << 22); 1083 E1000_WRITE_REG(hw, E1000_GCR, reg); 1084 } 1085 1086 return; 1087} 1088 1089/** 1090 * e1000_clear_vfta_82571 - Clear VLAN filter table 1091 * @hw: pointer to the HW structure 1092 * 1093 * Clears the register array which contains the VLAN filter table by 1094 * setting all the values to 0. 1095 **/ 1096static void e1000_clear_vfta_82571(struct e1000_hw *hw) 1097{ 1098 u32 offset; 1099 u32 vfta_value = 0; 1100 u32 vfta_offset = 0; 1101 u32 vfta_bit_in_reg = 0; 1102 1103 DEBUGFUNC("e1000_clear_vfta_82571"); 1104 1105 if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) { 1106 if (hw->mng_cookie.vlan_id != 0) { 1107 /* 1108 * The VFTA is a 4096b bit-field, each identifying 1109 * a single VLAN ID. The following operations 1110 * determine which 32b entry (i.e. offset) into the 1111 * array we want to set the VLAN ID (i.e. bit) of 1112 * the manageability unit. 1113 */ 1114 vfta_offset = (hw->mng_cookie.vlan_id >> 1115 E1000_VFTA_ENTRY_SHIFT) & 1116 E1000_VFTA_ENTRY_MASK; 1117 vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id & 1118 E1000_VFTA_ENTRY_BIT_SHIFT_MASK); 1119 } 1120 } 1121 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 1122 /* 1123 * If the offset we want to clear is the same offset of the 1124 * manageability VLAN ID, then clear all bits except that of 1125 * the manageability unit. 1126 */ 1127 vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; 1128 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value); 1129 E1000_WRITE_FLUSH(hw); 1130 } 1131} 1132 1133/** 1134 * e1000_check_mng_mode_82574 - Check manageability is enabled 1135 * @hw: pointer to the HW structure 1136 * 1137 * Reads the NVM Initialization Control Word 2 and returns TRUE 1138 * (>0) if any manageability is enabled, else FALSE (0). 1139 **/ 1140static bool e1000_check_mng_mode_82574(struct e1000_hw *hw) 1141{ 1142 u16 data; 1143 1144 DEBUGFUNC("e1000_check_mng_mode_82574"); 1145 1146 hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &data); 1147 return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0; 1148} 1149 1150/** 1151 * e1000_led_on_82574 - Turn LED on 1152 * @hw: pointer to the HW structure 1153 * 1154 * Turn LED on. 1155 **/ 1156static s32 e1000_led_on_82574(struct e1000_hw *hw) 1157{ 1158 u32 ctrl; 1159 u32 i; 1160 1161 DEBUGFUNC("e1000_led_on_82574"); 1162 1163 ctrl = hw->mac.ledctl_mode2; 1164 if (!(E1000_STATUS_LU & E1000_READ_REG(hw, E1000_STATUS))) { 1165 /* 1166 * If no link, then turn LED on by setting the invert bit 1167 * for each LED that's "on" (0x0E) in ledctl_mode2. 1168 */ 1169 for (i = 0; i < 4; i++) 1170 if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) == 1171 E1000_LEDCTL_MODE_LED_ON) 1172 ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8)); 1173 } 1174 E1000_WRITE_REG(hw, E1000_LEDCTL, ctrl); 1175 1176 return E1000_SUCCESS; 1177} 1178 1179/** 1180 * e1000_update_mc_addr_list_82571 - Update Multicast addresses 1181 * @hw: pointer to the HW structure 1182 * @mc_addr_list: array of multicast addresses to program 1183 * @mc_addr_count: number of multicast addresses to program 1184 * @rar_used_count: the first RAR register free to program 1185 * @rar_count: total number of supported Receive Address Registers 1186 * 1187 * Updates the Receive Address Registers and Multicast Table Array. 1188 * The caller must have a packed mc_addr_list of multicast addresses. 1189 * The parameter rar_count will usually be hw->mac.rar_entry_count 1190 * unless there are workarounds that change this. 1191 **/ 1192static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw, 1193 u8 *mc_addr_list, u32 mc_addr_count, 1194 u32 rar_used_count, u32 rar_count) 1195{ 1196 DEBUGFUNC("e1000_update_mc_addr_list_82571"); 1197 1198 if (e1000_get_laa_state_82571(hw)) 1199 rar_count--; 1200 1201 e1000_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count, 1202 rar_used_count, rar_count); 1203} 1204 1205/** 1206 * e1000_setup_link_82571 - Setup flow control and link settings 1207 * @hw: pointer to the HW structure 1208 * 1209 * Determines which flow control settings to use, then configures flow 1210 * control. Calls the appropriate media-specific link configuration 1211 * function. Assuming the adapter has a valid link partner, a valid link 1212 * should be established. Assumes the hardware has previously been reset 1213 * and the transmitter and receiver are not enabled. 1214 **/ 1215static s32 e1000_setup_link_82571(struct e1000_hw *hw) 1216{ 1217 DEBUGFUNC("e1000_setup_link_82571"); 1218 1219 /* 1220 * 82573 does not have a word in the NVM to determine 1221 * the default flow control setting, so we explicitly 1222 * set it to full. 1223 */ 1224 if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) && 1225 hw->fc.requested_mode == e1000_fc_default) 1226 hw->fc.requested_mode = e1000_fc_full; 1227 1228 return e1000_setup_link_generic(hw); 1229} 1230 1231/** 1232 * e1000_setup_copper_link_82571 - Configure copper link settings 1233 * @hw: pointer to the HW structure 1234 * 1235 * Configures the link for auto-neg or forced speed and duplex. Then we check 1236 * for link, once link is established calls to configure collision distance 1237 * and flow control are called. 1238 **/ 1239static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw) 1240{ 1241 u32 ctrl, led_ctrl; 1242 s32 ret_val; 1243 1244 DEBUGFUNC("e1000_setup_copper_link_82571"); 1245 1246 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1247 ctrl |= E1000_CTRL_SLU; 1248 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1249 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1250 1251 switch (hw->phy.type) { 1252 case e1000_phy_m88: 1253 case e1000_phy_bm: 1254 ret_val = e1000_copper_link_setup_m88(hw); 1255 break; 1256 case e1000_phy_igp_2: 1257 ret_val = e1000_copper_link_setup_igp(hw); 1258 /* Setup activity LED */ 1259 led_ctrl = E1000_READ_REG(hw, E1000_LEDCTL); 1260 led_ctrl &= IGP_ACTIVITY_LED_MASK; 1261 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 1262 E1000_WRITE_REG(hw, E1000_LEDCTL, led_ctrl); 1263 break; 1264 default: 1265 ret_val = -E1000_ERR_PHY; 1266 break; 1267 } 1268 1269 if (ret_val) 1270 goto out; 1271 1272 ret_val = e1000_setup_copper_link_generic(hw); 1273 1274out: 1275 return ret_val; 1276} 1277 1278/** 1279 * e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes 1280 * @hw: pointer to the HW structure 1281 * 1282 * Configures collision distance and flow control for fiber and serdes links. 1283 * Upon successful setup, poll for link. 1284 **/ 1285static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw) 1286{ 1287 DEBUGFUNC("e1000_setup_fiber_serdes_link_82571"); 1288 1289 switch (hw->mac.type) { 1290 case e1000_82571: 1291 case e1000_82572: 1292 /* 1293 * If SerDes loopback mode is entered, there is no form 1294 * of reset to take the adapter out of that mode. So we 1295 * have to explicitly take the adapter out of loopback 1296 * mode. This prevents drivers from twiddling their thumbs 1297 * if another tool failed to take it out of loopback mode. 1298 */ 1299 E1000_WRITE_REG(hw, E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); 1300 break; 1301 default: 1302 break; 1303 } 1304 1305 return e1000_setup_fiber_serdes_link_generic(hw); 1306} 1307 1308/** 1309 * e1000_valid_led_default_82571 - Verify a valid default LED config 1310 * @hw: pointer to the HW structure 1311 * @data: pointer to the NVM (EEPROM) 1312 * 1313 * Read the EEPROM for the current default LED configuration. If the 1314 * LED configuration is not valid, set to a valid LED configuration. 1315 **/ 1316static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data) 1317{ 1318 s32 ret_val; 1319 1320 DEBUGFUNC("e1000_valid_led_default_82571"); 1321 1322 ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); 1323 if (ret_val) { 1324 DEBUGOUT("NVM Read Error\n"); 1325 goto out; 1326 } 1327 1328 if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) && 1329 *data == ID_LED_RESERVED_F746) 1330 *data = ID_LED_DEFAULT_82573; 1331 else if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) 1332 *data = ID_LED_DEFAULT; 1333out: 1334 return ret_val; 1335} 1336 1337/** 1338 * e1000_get_laa_state_82571 - Get locally administered address state 1339 * @hw: pointer to the HW structure 1340 * 1341 * Retrieve and return the current locally administered address state. 1342 **/ 1343bool e1000_get_laa_state_82571(struct e1000_hw *hw) 1344{ 1345 DEBUGFUNC("e1000_get_laa_state_82571"); 1346 1347 if (hw->mac.type != e1000_82571) 1348 return FALSE; 1349 1350 return hw->dev_spec._82571.laa_is_present; 1351} 1352 1353/** 1354 * e1000_set_laa_state_82571 - Set locally administered address state 1355 * @hw: pointer to the HW structure 1356 * @state: enable/disable locally administered address 1357 * 1358 * Enable/Disable the current locally administered address state. 1359 **/ 1360void e1000_set_laa_state_82571(struct e1000_hw *hw, bool state) 1361{ 1362 DEBUGFUNC("e1000_set_laa_state_82571"); 1363 1364 if (hw->mac.type != e1000_82571) 1365 return; 1366 1367 hw->dev_spec._82571.laa_is_present = state; 1368 1369 /* If workaround is activated... */ 1370 if (state) 1371 /* 1372 * Hold a copy of the LAA in RAR[14] This is done so that 1373 * between the time RAR[0] gets clobbered and the time it 1374 * gets fixed, the actual LAA is in one of the RARs and no 1375 * incoming packets directed to this port are dropped. 1376 * Eventually the LAA will be in RAR[0] and RAR[14]. 1377 */ 1378 e1000_rar_set_generic(hw, hw->mac.addr, 1379 hw->mac.rar_entry_count - 1); 1380 return; 1381} 1382 1383/** 1384 * e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum 1385 * @hw: pointer to the HW structure 1386 * 1387 * Verifies that the EEPROM has completed the update. After updating the 1388 * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If 1389 * the checksum fix is not implemented, we need to set the bit and update 1390 * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect, 1391 * we need to return bad checksum. 1392 **/ 1393static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw) 1394{ 1395 struct e1000_nvm_info *nvm = &hw->nvm; 1396 s32 ret_val = E1000_SUCCESS; 1397 u16 data; 1398 1399 DEBUGFUNC("e1000_fix_nvm_checksum_82571"); 1400 1401 if (nvm->type != e1000_nvm_flash_hw) 1402 goto out; 1403 1404 /* 1405 * Check bit 4 of word 10h. If it is 0, firmware is done updating 1406 * 10h-12h. Checksum may need to be fixed. 1407 */ 1408 ret_val = nvm->ops.read(hw, 0x10, 1, &data); 1409 if (ret_val) 1410 goto out; 1411 1412 if (!(data & 0x10)) { 1413 /* 1414 * Read 0x23 and check bit 15. This bit is a 1 1415 * when the checksum has already been fixed. If 1416 * the checksum is still wrong and this bit is a 1417 * 1, we need to return bad checksum. Otherwise, 1418 * we need to set this bit to a 1 and update the 1419 * checksum. 1420 */ 1421 ret_val = nvm->ops.read(hw, 0x23, 1, &data); 1422 if (ret_val) 1423 goto out; 1424 1425 if (!(data & 0x8000)) { 1426 data |= 0x8000; 1427 ret_val = nvm->ops.write(hw, 0x23, 1, &data); 1428 if (ret_val) 1429 goto out; 1430 ret_val = nvm->ops.update(hw); 1431 } 1432 } 1433 1434out: 1435 return ret_val; 1436} 1437 1438/** 1439 * e1000_read_mac_addr_82571 - Read device MAC address 1440 * @hw: pointer to the HW structure 1441 **/ 1442static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw) 1443{ 1444 s32 ret_val = E1000_SUCCESS; 1445 1446 DEBUGFUNC("e1000_read_mac_addr_82571"); 1447 if (e1000_check_alt_mac_addr_generic(hw)) 1448 ret_val = e1000_read_mac_addr_generic(hw); 1449 1450 return ret_val; 1451} 1452 1453/** 1454 * e1000_power_down_phy_copper_82571 - Remove link during PHY power down 1455 * @hw: pointer to the HW structure 1456 * 1457 * In the case of a PHY power down to save power, or to turn off link during a 1458 * driver unload, or wake on lan is not enabled, remove the link. 1459 **/ 1460static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw) 1461{ 1462 struct e1000_phy_info *phy = &hw->phy; 1463 struct e1000_mac_info *mac = &hw->mac; 1464 1465 if (!(phy->ops.check_reset_block)) 1466 return; 1467 1468 /* If the management interface is not enabled, then power down */ 1469 if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw))) 1470 e1000_power_down_phy_copper(hw); 1471 1472 return; 1473} 1474 1475/** 1476 * e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters 1477 * @hw: pointer to the HW structure 1478 * 1479 * Clears the hardware counters by reading the counter registers. 1480 **/ 1481static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw) 1482{ 1483 DEBUGFUNC("e1000_clear_hw_cntrs_82571"); 1484 1485 e1000_clear_hw_cntrs_base_generic(hw); 1486 1487 E1000_READ_REG(hw, E1000_PRC64); 1488 E1000_READ_REG(hw, E1000_PRC127); 1489 E1000_READ_REG(hw, E1000_PRC255); 1490 E1000_READ_REG(hw, E1000_PRC511); 1491 E1000_READ_REG(hw, E1000_PRC1023); 1492 E1000_READ_REG(hw, E1000_PRC1522); 1493 E1000_READ_REG(hw, E1000_PTC64); 1494 E1000_READ_REG(hw, E1000_PTC127); 1495 E1000_READ_REG(hw, E1000_PTC255); 1496 E1000_READ_REG(hw, E1000_PTC511); 1497 E1000_READ_REG(hw, E1000_PTC1023); 1498 E1000_READ_REG(hw, E1000_PTC1522); 1499 1500 E1000_READ_REG(hw, E1000_ALGNERRC); 1501 E1000_READ_REG(hw, E1000_RXERRC); 1502 E1000_READ_REG(hw, E1000_TNCRS); 1503 E1000_READ_REG(hw, E1000_CEXTERR); 1504 E1000_READ_REG(hw, E1000_TSCTC); 1505 E1000_READ_REG(hw, E1000_TSCTFC); 1506 1507 E1000_READ_REG(hw, E1000_MGTPRC); 1508 E1000_READ_REG(hw, E1000_MGTPDC); 1509 E1000_READ_REG(hw, E1000_MGTPTC); 1510 1511 E1000_READ_REG(hw, E1000_IAC); 1512 E1000_READ_REG(hw, E1000_ICRXOC); 1513 1514 E1000_READ_REG(hw, E1000_ICRXPTC); 1515 E1000_READ_REG(hw, E1000_ICRXATC); 1516 E1000_READ_REG(hw, E1000_ICTXPTC); 1517 E1000_READ_REG(hw, E1000_ICTXATC); 1518 E1000_READ_REG(hw, E1000_ICTXQEC); 1519 E1000_READ_REG(hw, E1000_ICTXQMTC); 1520 E1000_READ_REG(hw, E1000_ICRXDMTC); 1521} 1522