cam.h revision 39212
1/* 2 * Data structures and definitions for the CAM system. 3 * 4 * Copyright (c) 1997 Justin T. Gibbs. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification, immediately at the beginning of the file. 13 * 2. The name of the author may not be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 20 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 * 28 * $Id$ 29 */ 30 31#ifndef _CAM_CAM_H 32#define _CAM_CAM_H 1 33 34#ifdef KERNEL 35#include <opt_cam.h> 36#endif /* KERNEL */ 37 38#include <sys/cdefs.h> 39 40typedef u_int path_id_t; 41typedef u_int target_id_t; 42typedef u_int lun_id_t; 43 44#define CAM_XPT_PATH_ID ((path_id_t)~0) 45#define CAM_BUS_WILDCARD ((path_id_t)~0) 46#define CAM_TARGET_WILDCARD ((target_id_t)~0) 47#define CAM_LUN_WILDCARD ((lun_id_t)~0) 48 49/* 50 * Maximum length for a CAM CDB. 51 */ 52#define CAM_MAX_CDBLEN 16 53 54/* 55 * Definition of a CAM peripheral driver entry. Peripheral drivers instantiate 56 * one of these for each device they wish to communicate with and pass it into 57 * the xpt layer when they wish to schedule work on that device via the 58 * xpt_schecule API. 59 */ 60struct cam_periph; 61 62/* 63 * Priority information for a CAM structure. The generation number is 64 * incremented everytime a new entry is entered into the queue giving round 65 * robin per priority level scheduling. 66 */ 67typedef struct { 68 u_int32_t priority; 69#define CAM_PRIORITY_NONE (u_int32_t)-1 70 u_int32_t generation; 71 int index; 72#define CAM_UNQUEUED_INDEX -1 73#define CAM_ACTIVE_INDEX -2 74#define CAM_DONEQ_INDEX -3 75} cam_pinfo; 76 77/* CAM flags */ 78typedef enum { 79 CAM_FLAG_NONE = 0x00, 80 CAM_EXPECT_INQ_CHANGE = 0x01 81} cam_flags; 82 83/* CAM Status field values */ 84typedef enum { 85 CAM_REQ_INPROG, /* CCB request is in progress */ 86 CAM_REQ_CMP, /* CCB request completed without error */ 87 CAM_REQ_ABORTED, /* CCB request aborted by the host */ 88 CAM_UA_ABORT, /* Unable to abort CCB request */ 89 CAM_REQ_CMP_ERR, /* CCB request completed with an error */ 90 CAM_BUSY, /* CAM subsytem is busy */ 91 CAM_REQ_INVALID, /* CCB request was invalid */ 92 CAM_PATH_INVALID, /* Supplied Path ID is invalid */ 93 CAM_DEV_NOT_THERE, /* SCSI Device Not Installed/there */ 94 CAM_UA_TERMIO, /* Unable to terminate I/O CCB request */ 95 CAM_SEL_TIMEOUT, /* Target Selection Timeout */ 96 CAM_CMD_TIMEOUT, /* Command timeout */ 97 CAM_SCSI_STATUS_ERROR, /* SCSI error, look at error code in CCB */ 98 CAM_MSG_REJECT_REC, /* Message Reject Reveived */ 99 CAM_SCSI_BUS_RESET, /* SCSI Bus Reset Sent/Received */ 100 CAM_UNCOR_PARITY, /* Uncorrectable parity error occurred */ 101 CAM_AUTOSENSE_FAIL = 0x10,/* Autosense: request sense cmd fail */ 102 CAM_NO_HBA, /* No HBA Detected error */ 103 CAM_DATA_RUN_ERR, /* Data Overrun error */ 104 CAM_UNEXP_BUSFREE, /* Unexpected Bus Free */ 105 CAM_SEQUENCE_FAIL, /* Target Bus Phase Sequence Failure */ 106 CAM_CCB_LEN_ERR, /* CCB length supplied is inadequate */ 107 CAM_PROVIDE_FAIL, /* Unable to provide requested capability */ 108 CAM_BDR_SENT, /* A SCSI BDR msg was sent to target */ 109 CAM_REQ_TERMIO, /* CCB request terminated by the host */ 110 CAM_UNREC_HBA_ERROR, /* Unrecoverable Host Bus Adapter Error */ 111 CAM_REQ_TOO_BIG, /* The request was too large for this host */ 112 CAM_REQUEUE_REQ, /* 113 * This request should be requeued to preserve 114 * transaction ordering. This typically occurs 115 * when the SIM recognizes an error that should 116 * freeze the queue and must place additional 117 * requests for the target at the sim level 118 * back into the XPT queue. 119 */ 120 CAM_IDE = 0x33, /* Initiator Detected Error */ 121 CAM_RESRC_UNAVAIL, /* Resource Unavailable */ 122 CAM_UNACKED_EVENT, /* Unacknowledged Event by Host */ 123 CAM_MESSAGE_RECV, /* Message Received in Host Target Mode */ 124 CAM_INVALID_CDB, /* Invalid CDB received in Host Target Mode */ 125 CAM_LUN_INVALID, /* Lun supplied is invalid */ 126 CAM_TID_INVALID, /* Target ID supplied is invalid */ 127 CAM_FUNC_NOTAVAIL, /* The requested function is not available */ 128 CAM_NO_NEXUS, /* Nexus is not established */ 129 CAM_IID_INVALID, /* The initiator ID is invalid */ 130 CAM_CDB_RECVD, /* The SCSI CDB has been received */ 131 CAM_LUN_ALRDY_ENA, /* The LUN is already eanbeld for target mode */ 132 CAM_SCSI_BUSY, /* SCSI Bus Busy */ 133 134 CAM_DEV_QFRZN = 0x40, /* The DEV queue is frozen w/this err */ 135 136 /* Autosense data valid for target */ 137 CAM_AUTOSNS_VALID = 0x80, 138 CAM_RELEASE_SIMQ = 0x100,/* SIM ready to take more commands */ 139 CAM_SIM_QUEUED = 0x200,/* SIM has this command in it's queue */ 140 141 CAM_STATUS_MASK = 0x3F, /* Mask bits for just the status # */ 142} cam_status; 143 144__BEGIN_DECLS 145typedef int (cam_quirkmatch_t)(caddr_t, caddr_t); 146 147caddr_t cam_quirkmatch(caddr_t target, caddr_t quirk_table, int num_entries, 148 int entry_size, cam_quirkmatch_t *comp_func); 149 150void cam_strvis(u_int8_t *dst, const u_int8_t *src, int srclen, int dstlen); 151 152int cam_strmatch(const u_int8_t *str, const u_int8_t *pattern, int str_len); 153__END_DECLS 154 155#ifdef KERNEL 156static __inline void cam_init_pinfo(cam_pinfo *pinfo); 157 158static __inline void cam_init_pinfo(cam_pinfo *pinfo) 159{ 160 pinfo->priority = CAM_PRIORITY_NONE; 161 pinfo->index = CAM_UNQUEUED_INDEX; 162} 163#endif /* KERNEL */ 164 165#endif /* _CAM_CAM_H */ 166