omap3-cm-t3530.dts revision 284090 
1/*
2 * Support for CompuLab CM-T3530
3 */
4/dts-v1/;
5
6#include "omap34xx.dtsi"
7#include "omap3-cm-t3x30.dtsi"
8
9/ {
10	model = "CompuLab CM-T3530";
11	compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
12
13	/* Regulator to trigger the reset signal of the Wifi module */
14	mmc2_sdio_reset: regulator-mmc2-sdio-reset {
15		compatible = "regulator-fixed";
16		regulator-name = "regulator-mmc2-sdio-reset";
17		regulator-min-microvolt = <3300000>;
18		regulator-max-microvolt = <3300000>;
19		gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
20		enable-active-high;
21	};
22};
23
24&omap3_pmx_core {
25	mmc2_pins: pinmux_mmc2_pins {
26		pinctrl-single,pins = <
27			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
28			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
29			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat0.sdmmc2_dat0 */
30			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat1.sdmmc2_dat1 */
31			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat2.sdmmc2_dat2 */
32			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat3.sdmmc2_dat3 */
33			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat4.sdmmc2_dir_dat0 */
34			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat5.sdmmc2_dir_dat1 */
35			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat6.sdmmc2_dir_cmd */
36			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)		/* sdmmc2_dat7.sdmmc2_clkin */
37		>;
38	};
39};
40
41&mmc2 {
42	pinctrl-names = "default";
43	pinctrl-0 = <&mmc2_pins>;
44	vmmc-supply = <&mmc2_sdio_reset>;
45	non-removable;
46	bus-width = <4>;
47	cap-power-off-card;
48};
49
50&dss {
51	status = "ok";
52
53	pinctrl-names = "default";
54	pinctrl-0 = <
55		&dss_dpi_pins_common
56		&dss_dpi_pins_cm_t35x
57	>;
58};
59
60