ixgbe_x550.c revision 295528
1/****************************************************************************** 2 3 Copyright (c) 2001-2015, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32******************************************************************************/ 33/*$FreeBSD: stable/10/sys/dev/ixgbe/ixgbe_x550.c 295528 2016-02-11 16:54:23Z smh $*/ 34 35#include "ixgbe_x550.h" 36#include "ixgbe_x540.h" 37#include "ixgbe_type.h" 38#include "ixgbe_api.h" 39#include "ixgbe_common.h" 40#include "ixgbe_phy.h" 41 42static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed); 43 44/** 45 * ixgbe_init_ops_X550 - Inits func ptrs and MAC type 46 * @hw: pointer to hardware structure 47 * 48 * Initialize the function pointers and assign the MAC type for X550. 49 * Does not touch the hardware. 50 **/ 51s32 ixgbe_init_ops_X550(struct ixgbe_hw *hw) 52{ 53 struct ixgbe_mac_info *mac = &hw->mac; 54 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 55 s32 ret_val; 56 57 DEBUGFUNC("ixgbe_init_ops_X550"); 58 59 ret_val = ixgbe_init_ops_X540(hw); 60 mac->ops.dmac_config = ixgbe_dmac_config_X550; 61 mac->ops.dmac_config_tcs = ixgbe_dmac_config_tcs_X550; 62 mac->ops.dmac_update_tcs = ixgbe_dmac_update_tcs_X550; 63 mac->ops.setup_eee = ixgbe_setup_eee_X550; 64 mac->ops.set_source_address_pruning = 65 ixgbe_set_source_address_pruning_X550; 66 mac->ops.set_ethertype_anti_spoofing = 67 ixgbe_set_ethertype_anti_spoofing_X550; 68 69 mac->ops.get_rtrup2tc = ixgbe_dcb_get_rtrup2tc_generic; 70 eeprom->ops.init_params = ixgbe_init_eeprom_params_X550; 71 eeprom->ops.calc_checksum = ixgbe_calc_eeprom_checksum_X550; 72 eeprom->ops.read = ixgbe_read_ee_hostif_X550; 73 eeprom->ops.read_buffer = ixgbe_read_ee_hostif_buffer_X550; 74 eeprom->ops.write = ixgbe_write_ee_hostif_X550; 75 eeprom->ops.write_buffer = ixgbe_write_ee_hostif_buffer_X550; 76 eeprom->ops.update_checksum = ixgbe_update_eeprom_checksum_X550; 77 eeprom->ops.validate_checksum = ixgbe_validate_eeprom_checksum_X550; 78 79 mac->ops.disable_mdd = ixgbe_disable_mdd_X550; 80 mac->ops.enable_mdd = ixgbe_enable_mdd_X550; 81 mac->ops.mdd_event = ixgbe_mdd_event_X550; 82 mac->ops.restore_mdd_vf = ixgbe_restore_mdd_vf_X550; 83 mac->ops.disable_rx = ixgbe_disable_rx_x550; 84 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_10G_T) { 85 hw->mac.ops.led_on = ixgbe_led_on_t_X550em; 86 hw->mac.ops.led_off = ixgbe_led_off_t_X550em; 87 } 88 return ret_val; 89} 90 91/** 92 * ixgbe_read_cs4227 - Read CS4227 register 93 * @hw: pointer to hardware structure 94 * @reg: register number to write 95 * @value: pointer to receive value read 96 * 97 * Returns status code 98 **/ 99static s32 ixgbe_read_cs4227(struct ixgbe_hw *hw, u16 reg, u16 *value) 100{ 101 return ixgbe_read_i2c_combined_unlocked(hw, IXGBE_CS4227, reg, value); 102} 103 104/** 105 * ixgbe_write_cs4227 - Write CS4227 register 106 * @hw: pointer to hardware structure 107 * @reg: register number to write 108 * @value: value to write to register 109 * 110 * Returns status code 111 **/ 112static s32 ixgbe_write_cs4227(struct ixgbe_hw *hw, u16 reg, u16 value) 113{ 114 return ixgbe_write_i2c_combined_unlocked(hw, IXGBE_CS4227, reg, value); 115} 116 117/** 118 * ixgbe_read_pe - Read register from port expander 119 * @hw: pointer to hardware structure 120 * @reg: register number to read 121 * @value: pointer to receive read value 122 * 123 * Returns status code 124 **/ 125static s32 ixgbe_read_pe(struct ixgbe_hw *hw, u8 reg, u8 *value) 126{ 127 s32 status; 128 129 status = ixgbe_read_i2c_byte_unlocked(hw, reg, IXGBE_PE, value); 130 if (status != IXGBE_SUCCESS) 131 ERROR_REPORT2(IXGBE_ERROR_CAUTION, 132 "port expander access failed with %d\n", status); 133 return status; 134} 135 136/** 137 * ixgbe_write_pe - Write register to port expander 138 * @hw: pointer to hardware structure 139 * @reg: register number to write 140 * @value: value to write 141 * 142 * Returns status code 143 **/ 144static s32 ixgbe_write_pe(struct ixgbe_hw *hw, u8 reg, u8 value) 145{ 146 s32 status; 147 148 status = ixgbe_write_i2c_byte_unlocked(hw, reg, IXGBE_PE, value); 149 if (status != IXGBE_SUCCESS) 150 ERROR_REPORT2(IXGBE_ERROR_CAUTION, 151 "port expander access failed with %d\n", status); 152 return status; 153} 154 155/** 156 * ixgbe_reset_cs4227 - Reset CS4227 using port expander 157 * @hw: pointer to hardware structure 158 * 159 * This function assumes that the caller has acquired the proper semaphore. 160 * Returns error code 161 **/ 162static s32 ixgbe_reset_cs4227(struct ixgbe_hw *hw) 163{ 164 s32 status; 165 u32 retry; 166 u16 value; 167 u8 reg; 168 169 /* Trigger hard reset. */ 170 status = ixgbe_read_pe(hw, IXGBE_PE_OUTPUT, ®); 171 if (status != IXGBE_SUCCESS) 172 return status; 173 reg |= IXGBE_PE_BIT1; 174 status = ixgbe_write_pe(hw, IXGBE_PE_OUTPUT, reg); 175 if (status != IXGBE_SUCCESS) 176 return status; 177 178 status = ixgbe_read_pe(hw, IXGBE_PE_CONFIG, ®); 179 if (status != IXGBE_SUCCESS) 180 return status; 181 reg &= ~IXGBE_PE_BIT1; 182 status = ixgbe_write_pe(hw, IXGBE_PE_CONFIG, reg); 183 if (status != IXGBE_SUCCESS) 184 return status; 185 186 status = ixgbe_read_pe(hw, IXGBE_PE_OUTPUT, ®); 187 if (status != IXGBE_SUCCESS) 188 return status; 189 reg &= ~IXGBE_PE_BIT1; 190 status = ixgbe_write_pe(hw, IXGBE_PE_OUTPUT, reg); 191 if (status != IXGBE_SUCCESS) 192 return status; 193 194 usec_delay(IXGBE_CS4227_RESET_HOLD); 195 196 status = ixgbe_read_pe(hw, IXGBE_PE_OUTPUT, ®); 197 if (status != IXGBE_SUCCESS) 198 return status; 199 reg |= IXGBE_PE_BIT1; 200 status = ixgbe_write_pe(hw, IXGBE_PE_OUTPUT, reg); 201 if (status != IXGBE_SUCCESS) 202 return status; 203 204 /* Wait for the reset to complete. */ 205 msec_delay(IXGBE_CS4227_RESET_DELAY); 206 for (retry = 0; retry < IXGBE_CS4227_RETRIES; retry++) { 207 status = ixgbe_read_cs4227(hw, IXGBE_CS4227_EFUSE_STATUS, 208 &value); 209 if (status == IXGBE_SUCCESS && 210 value == IXGBE_CS4227_EEPROM_LOAD_OK) 211 break; 212 msec_delay(IXGBE_CS4227_CHECK_DELAY); 213 } 214 if (retry == IXGBE_CS4227_RETRIES) { 215 ERROR_REPORT1(IXGBE_ERROR_INVALID_STATE, 216 "CS4227 reset did not complete."); 217 return IXGBE_ERR_PHY; 218 } 219 220 status = ixgbe_read_cs4227(hw, IXGBE_CS4227_EEPROM_STATUS, &value); 221 if (status != IXGBE_SUCCESS || 222 !(value & IXGBE_CS4227_EEPROM_LOAD_OK)) { 223 ERROR_REPORT1(IXGBE_ERROR_INVALID_STATE, 224 "CS4227 EEPROM did not load successfully."); 225 return IXGBE_ERR_PHY; 226 } 227 228 return IXGBE_SUCCESS; 229} 230 231/** 232 * ixgbe_check_cs4227 - Check CS4227 and reset as needed 233 * @hw: pointer to hardware structure 234 **/ 235static void ixgbe_check_cs4227(struct ixgbe_hw *hw) 236{ 237 s32 status = IXGBE_SUCCESS; 238 u32 swfw_mask = hw->phy.phy_semaphore_mask; 239 u16 value = 0; 240 u8 retry; 241 242 for (retry = 0; retry < IXGBE_CS4227_RETRIES; retry++) { 243 status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask); 244 if (status != IXGBE_SUCCESS) { 245 ERROR_REPORT2(IXGBE_ERROR_CAUTION, 246 "semaphore failed with %d", status); 247 msec_delay(IXGBE_CS4227_CHECK_DELAY); 248 continue; 249 } 250 251 /* Get status of reset flow. */ 252 status = ixgbe_read_cs4227(hw, IXGBE_CS4227_SCRATCH, &value); 253 254 if (status == IXGBE_SUCCESS && 255 value == IXGBE_CS4227_RESET_COMPLETE) 256 goto out; 257 258 if (status != IXGBE_SUCCESS || 259 value != IXGBE_CS4227_RESET_PENDING) 260 break; 261 262 /* Reset is pending. Wait and check again. */ 263 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 264 msec_delay(IXGBE_CS4227_CHECK_DELAY); 265 } 266 267 /* If still pending, assume other instance failed. */ 268 if (retry == IXGBE_CS4227_RETRIES) { 269 status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask); 270 if (status != IXGBE_SUCCESS) { 271 ERROR_REPORT2(IXGBE_ERROR_CAUTION, 272 "semaphore failed with %d", status); 273 return; 274 } 275 } 276 277 /* Reset the CS4227. */ 278 status = ixgbe_reset_cs4227(hw); 279 if (status != IXGBE_SUCCESS) { 280 ERROR_REPORT2(IXGBE_ERROR_INVALID_STATE, 281 "CS4227 reset failed: %d", status); 282 goto out; 283 } 284 285 /* Reset takes so long, temporarily release semaphore in case the 286 * other driver instance is waiting for the reset indication. 287 */ 288 ixgbe_write_cs4227(hw, IXGBE_CS4227_SCRATCH, 289 IXGBE_CS4227_RESET_PENDING); 290 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 291 msec_delay(10); 292 status = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask); 293 if (status != IXGBE_SUCCESS) { 294 ERROR_REPORT2(IXGBE_ERROR_CAUTION, 295 "semaphore failed with %d", status); 296 return; 297 } 298 299 /* Record completion for next time. */ 300 status = ixgbe_write_cs4227(hw, IXGBE_CS4227_SCRATCH, 301 IXGBE_CS4227_RESET_COMPLETE); 302 303out: 304 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 305 msec_delay(hw->eeprom.semaphore_delay); 306} 307 308/** 309 * ixgbe_setup_mux_ctl - Setup ESDP register for I2C mux control 310 * @hw: pointer to hardware structure 311 **/ 312static void ixgbe_setup_mux_ctl(struct ixgbe_hw *hw) 313{ 314 u32 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 315 316 if (hw->bus.lan_id) { 317 esdp &= ~(IXGBE_ESDP_SDP1_NATIVE | IXGBE_ESDP_SDP1); 318 esdp |= IXGBE_ESDP_SDP1_DIR; 319 } 320 esdp &= ~(IXGBE_ESDP_SDP0_NATIVE | IXGBE_ESDP_SDP0_DIR); 321 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 322 IXGBE_WRITE_FLUSH(hw); 323} 324 325/** 326 * ixgbe_identify_phy_x550em - Get PHY type based on device id 327 * @hw: pointer to hardware structure 328 * 329 * Returns error code 330 */ 331static s32 ixgbe_identify_phy_x550em(struct ixgbe_hw *hw) 332{ 333 switch (hw->device_id) { 334 case IXGBE_DEV_ID_X550EM_X_SFP: 335 /* set up for CS4227 usage */ 336 hw->phy.phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM; 337 ixgbe_setup_mux_ctl(hw); 338 ixgbe_check_cs4227(hw); 339 340 return ixgbe_identify_module_generic(hw); 341 break; 342 case IXGBE_DEV_ID_X550EM_X_KX4: 343 hw->phy.type = ixgbe_phy_x550em_kx4; 344 break; 345 case IXGBE_DEV_ID_X550EM_X_KR: 346 hw->phy.type = ixgbe_phy_x550em_kr; 347 break; 348 case IXGBE_DEV_ID_X550EM_X_1G_T: 349 case IXGBE_DEV_ID_X550EM_X_10G_T: 350 return ixgbe_identify_phy_generic(hw); 351 default: 352 break; 353 } 354 return IXGBE_SUCCESS; 355} 356 357static s32 ixgbe_read_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr, 358 u32 device_type, u16 *phy_data) 359{ 360 UNREFERENCED_4PARAMETER(*hw, reg_addr, device_type, *phy_data); 361 return IXGBE_NOT_IMPLEMENTED; 362} 363 364static s32 ixgbe_write_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr, 365 u32 device_type, u16 phy_data) 366{ 367 UNREFERENCED_4PARAMETER(*hw, reg_addr, device_type, phy_data); 368 return IXGBE_NOT_IMPLEMENTED; 369} 370 371/** 372* ixgbe_init_ops_X550EM - Inits func ptrs and MAC type 373* @hw: pointer to hardware structure 374* 375* Initialize the function pointers and for MAC type X550EM. 376* Does not touch the hardware. 377**/ 378s32 ixgbe_init_ops_X550EM(struct ixgbe_hw *hw) 379{ 380 struct ixgbe_mac_info *mac = &hw->mac; 381 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 382 struct ixgbe_phy_info *phy = &hw->phy; 383 s32 ret_val; 384 385 DEBUGFUNC("ixgbe_init_ops_X550EM"); 386 387 /* Similar to X550 so start there. */ 388 ret_val = ixgbe_init_ops_X550(hw); 389 390 /* Since this function eventually calls 391 * ixgbe_init_ops_540 by design, we are setting 392 * the pointers to NULL explicitly here to overwrite 393 * the values being set in the x540 function. 394 */ 395 396 /* FCOE not supported in x550EM */ 397 mac->ops.get_san_mac_addr = NULL; 398 mac->ops.set_san_mac_addr = NULL; 399 mac->ops.get_wwn_prefix = NULL; 400 mac->ops.get_fcoe_boot_status = NULL; 401 402 /* IPsec not supported in x550EM */ 403 mac->ops.disable_sec_rx_path = NULL; 404 mac->ops.enable_sec_rx_path = NULL; 405 406 /* AUTOC register is not present in x550EM. */ 407 mac->ops.prot_autoc_read = NULL; 408 mac->ops.prot_autoc_write = NULL; 409 410 /* X550EM bus type is internal*/ 411 hw->bus.type = ixgbe_bus_type_internal; 412 mac->ops.get_bus_info = ixgbe_get_bus_info_X550em; 413 414 if (hw->mac.type == ixgbe_mac_X550EM_x) { 415 mac->ops.read_iosf_sb_reg = ixgbe_read_iosf_sb_reg_x550; 416 mac->ops.write_iosf_sb_reg = ixgbe_write_iosf_sb_reg_x550; 417 } 418 419 mac->ops.get_media_type = ixgbe_get_media_type_X550em; 420 mac->ops.setup_sfp = ixgbe_setup_sfp_modules_X550em; 421 mac->ops.get_link_capabilities = ixgbe_get_link_capabilities_X550em; 422 mac->ops.reset_hw = ixgbe_reset_hw_X550em; 423 mac->ops.get_supported_physical_layer = 424 ixgbe_get_supported_physical_layer_X550em; 425 426 if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) 427 mac->ops.setup_fc = ixgbe_setup_fc_generic; 428 else 429 mac->ops.setup_fc = ixgbe_setup_fc_X550em; 430 431 mac->ops.acquire_swfw_sync = ixgbe_acquire_swfw_sync_X550em; 432 mac->ops.release_swfw_sync = ixgbe_release_swfw_sync_X550em; 433 434 if (hw->device_id != IXGBE_DEV_ID_X550EM_X_KR) 435 mac->ops.setup_eee = NULL; 436 437 /* PHY */ 438 phy->ops.init = ixgbe_init_phy_ops_X550em; 439 phy->ops.identify = ixgbe_identify_phy_x550em; 440 if (mac->ops.get_media_type(hw) != ixgbe_media_type_copper) 441 phy->ops.set_phy_power = NULL; 442 443 444 /* EEPROM */ 445 eeprom->ops.init_params = ixgbe_init_eeprom_params_X540; 446 eeprom->ops.read = ixgbe_read_ee_hostif_X550; 447 eeprom->ops.read_buffer = ixgbe_read_ee_hostif_buffer_X550; 448 eeprom->ops.write = ixgbe_write_ee_hostif_X550; 449 eeprom->ops.write_buffer = ixgbe_write_ee_hostif_buffer_X550; 450 eeprom->ops.update_checksum = ixgbe_update_eeprom_checksum_X550; 451 eeprom->ops.validate_checksum = ixgbe_validate_eeprom_checksum_X550; 452 eeprom->ops.calc_checksum = ixgbe_calc_eeprom_checksum_X550; 453 454 return ret_val; 455} 456 457/** 458 * ixgbe_dmac_config_X550 459 * @hw: pointer to hardware structure 460 * 461 * Configure DMA coalescing. If enabling dmac, dmac is activated. 462 * When disabling dmac, dmac enable dmac bit is cleared. 463 **/ 464s32 ixgbe_dmac_config_X550(struct ixgbe_hw *hw) 465{ 466 u32 reg, high_pri_tc; 467 468 DEBUGFUNC("ixgbe_dmac_config_X550"); 469 470 /* Disable DMA coalescing before configuring */ 471 reg = IXGBE_READ_REG(hw, IXGBE_DMACR); 472 reg &= ~IXGBE_DMACR_DMAC_EN; 473 IXGBE_WRITE_REG(hw, IXGBE_DMACR, reg); 474 475 /* Disable DMA Coalescing if the watchdog timer is 0 */ 476 if (!hw->mac.dmac_config.watchdog_timer) 477 goto out; 478 479 ixgbe_dmac_config_tcs_X550(hw); 480 481 /* Configure DMA Coalescing Control Register */ 482 reg = IXGBE_READ_REG(hw, IXGBE_DMACR); 483 484 /* Set the watchdog timer in units of 40.96 usec */ 485 reg &= ~IXGBE_DMACR_DMACWT_MASK; 486 reg |= (hw->mac.dmac_config.watchdog_timer * 100) / 4096; 487 488 reg &= ~IXGBE_DMACR_HIGH_PRI_TC_MASK; 489 /* If fcoe is enabled, set high priority traffic class */ 490 if (hw->mac.dmac_config.fcoe_en) { 491 high_pri_tc = 1 << hw->mac.dmac_config.fcoe_tc; 492 reg |= ((high_pri_tc << IXGBE_DMACR_HIGH_PRI_TC_SHIFT) & 493 IXGBE_DMACR_HIGH_PRI_TC_MASK); 494 } 495 reg |= IXGBE_DMACR_EN_MNG_IND; 496 497 /* Enable DMA coalescing after configuration */ 498 reg |= IXGBE_DMACR_DMAC_EN; 499 IXGBE_WRITE_REG(hw, IXGBE_DMACR, reg); 500 501out: 502 return IXGBE_SUCCESS; 503} 504 505/** 506 * ixgbe_dmac_config_tcs_X550 507 * @hw: pointer to hardware structure 508 * 509 * Configure DMA coalescing threshold per TC. The dmac enable bit must 510 * be cleared before configuring. 511 **/ 512s32 ixgbe_dmac_config_tcs_X550(struct ixgbe_hw *hw) 513{ 514 u32 tc, reg, pb_headroom, rx_pb_size, maxframe_size_kb; 515 516 DEBUGFUNC("ixgbe_dmac_config_tcs_X550"); 517 518 /* Configure DMA coalescing enabled */ 519 switch (hw->mac.dmac_config.link_speed) { 520 case IXGBE_LINK_SPEED_100_FULL: 521 pb_headroom = IXGBE_DMACRXT_100M; 522 break; 523 case IXGBE_LINK_SPEED_1GB_FULL: 524 pb_headroom = IXGBE_DMACRXT_1G; 525 break; 526 default: 527 pb_headroom = IXGBE_DMACRXT_10G; 528 break; 529 } 530 531 maxframe_size_kb = ((IXGBE_READ_REG(hw, IXGBE_MAXFRS) >> 532 IXGBE_MHADD_MFS_SHIFT) / 1024); 533 534 /* Set the per Rx packet buffer receive threshold */ 535 for (tc = 0; tc < IXGBE_DCB_MAX_TRAFFIC_CLASS; tc++) { 536 reg = IXGBE_READ_REG(hw, IXGBE_DMCTH(tc)); 537 reg &= ~IXGBE_DMCTH_DMACRXT_MASK; 538 539 if (tc < hw->mac.dmac_config.num_tcs) { 540 /* Get Rx PB size */ 541 rx_pb_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(tc)); 542 rx_pb_size = (rx_pb_size & IXGBE_RXPBSIZE_MASK) >> 543 IXGBE_RXPBSIZE_SHIFT; 544 545 /* Calculate receive buffer threshold in kilobytes */ 546 if (rx_pb_size > pb_headroom) 547 rx_pb_size = rx_pb_size - pb_headroom; 548 else 549 rx_pb_size = 0; 550 551 /* Minimum of MFS shall be set for DMCTH */ 552 reg |= (rx_pb_size > maxframe_size_kb) ? 553 rx_pb_size : maxframe_size_kb; 554 } 555 IXGBE_WRITE_REG(hw, IXGBE_DMCTH(tc), reg); 556 } 557 return IXGBE_SUCCESS; 558} 559 560/** 561 * ixgbe_dmac_update_tcs_X550 562 * @hw: pointer to hardware structure 563 * 564 * Disables dmac, updates per TC settings, and then enables dmac. 565 **/ 566s32 ixgbe_dmac_update_tcs_X550(struct ixgbe_hw *hw) 567{ 568 u32 reg; 569 570 DEBUGFUNC("ixgbe_dmac_update_tcs_X550"); 571 572 /* Disable DMA coalescing before configuring */ 573 reg = IXGBE_READ_REG(hw, IXGBE_DMACR); 574 reg &= ~IXGBE_DMACR_DMAC_EN; 575 IXGBE_WRITE_REG(hw, IXGBE_DMACR, reg); 576 577 ixgbe_dmac_config_tcs_X550(hw); 578 579 /* Enable DMA coalescing after configuration */ 580 reg = IXGBE_READ_REG(hw, IXGBE_DMACR); 581 reg |= IXGBE_DMACR_DMAC_EN; 582 IXGBE_WRITE_REG(hw, IXGBE_DMACR, reg); 583 584 return IXGBE_SUCCESS; 585} 586 587/** 588 * ixgbe_init_eeprom_params_X550 - Initialize EEPROM params 589 * @hw: pointer to hardware structure 590 * 591 * Initializes the EEPROM parameters ixgbe_eeprom_info within the 592 * ixgbe_hw struct in order to set up EEPROM access. 593 **/ 594s32 ixgbe_init_eeprom_params_X550(struct ixgbe_hw *hw) 595{ 596 struct ixgbe_eeprom_info *eeprom = &hw->eeprom; 597 u32 eec; 598 u16 eeprom_size; 599 600 DEBUGFUNC("ixgbe_init_eeprom_params_X550"); 601 602 if (eeprom->type == ixgbe_eeprom_uninitialized) { 603 eeprom->semaphore_delay = 10; 604 eeprom->type = ixgbe_flash; 605 606 eec = IXGBE_READ_REG(hw, IXGBE_EEC); 607 eeprom_size = (u16)((eec & IXGBE_EEC_SIZE) >> 608 IXGBE_EEC_SIZE_SHIFT); 609 eeprom->word_size = 1 << (eeprom_size + 610 IXGBE_EEPROM_WORD_SIZE_SHIFT); 611 612 DEBUGOUT2("Eeprom params: type = %d, size = %d\n", 613 eeprom->type, eeprom->word_size); 614 } 615 616 return IXGBE_SUCCESS; 617} 618 619/** 620 * ixgbe_setup_eee_X550 - Enable/disable EEE support 621 * @hw: pointer to the HW structure 622 * @enable_eee: boolean flag to enable EEE 623 * 624 * Enable/disable EEE based on enable_eee flag. 625 * Auto-negotiation must be started after BASE-T EEE bits in PHY register 7.3C 626 * are modified. 627 * 628 **/ 629s32 ixgbe_setup_eee_X550(struct ixgbe_hw *hw, bool enable_eee) 630{ 631 u32 eeer; 632 u16 autoneg_eee_reg; 633 u32 link_reg; 634 s32 status; 635 u32 fuse; 636 637 DEBUGFUNC("ixgbe_setup_eee_X550"); 638 639 eeer = IXGBE_READ_REG(hw, IXGBE_EEER); 640 /* Enable or disable EEE per flag */ 641 if (enable_eee) { 642 eeer |= (IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN); 643 644 if (hw->mac.type == ixgbe_mac_X550) { 645 /* Advertise EEE capability */ 646 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, 647 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_eee_reg); 648 649 autoneg_eee_reg |= (IXGBE_AUTO_NEG_10GBASE_EEE_ADVT | 650 IXGBE_AUTO_NEG_1000BASE_EEE_ADVT | 651 IXGBE_AUTO_NEG_100BASE_EEE_ADVT); 652 653 hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, 654 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_eee_reg); 655 } else if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) { 656 /* Not supported on first revision. */ 657 fuse = IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0)); 658 if (!(fuse & IXGBE_FUSES0_REV1)) 659 return IXGBE_SUCCESS; 660 661 status = ixgbe_read_iosf_sb_reg_x550(hw, 662 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 663 IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); 664 if (status != IXGBE_SUCCESS) 665 return status; 666 667 link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR | 668 IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX; 669 670 /* Don't advertise FEC capability when EEE enabled. */ 671 link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC; 672 673 status = ixgbe_write_iosf_sb_reg_x550(hw, 674 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 675 IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); 676 if (status != IXGBE_SUCCESS) 677 return status; 678 } 679 } else { 680 eeer &= ~(IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN); 681 682 if (hw->mac.type == ixgbe_mac_X550) { 683 /* Disable advertised EEE capability */ 684 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, 685 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_eee_reg); 686 687 autoneg_eee_reg &= ~(IXGBE_AUTO_NEG_10GBASE_EEE_ADVT | 688 IXGBE_AUTO_NEG_1000BASE_EEE_ADVT | 689 IXGBE_AUTO_NEG_100BASE_EEE_ADVT); 690 691 hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, 692 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_eee_reg); 693 } else if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) { 694 status = ixgbe_read_iosf_sb_reg_x550(hw, 695 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 696 IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); 697 if (status != IXGBE_SUCCESS) 698 return status; 699 700 link_reg &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR | 701 IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX); 702 703 /* Advertise FEC capability when EEE is disabled. */ 704 link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC; 705 706 status = ixgbe_write_iosf_sb_reg_x550(hw, 707 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 708 IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); 709 if (status != IXGBE_SUCCESS) 710 return status; 711 } 712 } 713 IXGBE_WRITE_REG(hw, IXGBE_EEER, eeer); 714 715 return IXGBE_SUCCESS; 716} 717 718/** 719 * ixgbe_set_source_address_pruning_X550 - Enable/Disbale source address pruning 720 * @hw: pointer to hardware structure 721 * @enable: enable or disable source address pruning 722 * @pool: Rx pool to set source address pruning for 723 **/ 724void ixgbe_set_source_address_pruning_X550(struct ixgbe_hw *hw, bool enable, 725 unsigned int pool) 726{ 727 u64 pfflp; 728 729 /* max rx pool is 63 */ 730 if (pool > 63) 731 return; 732 733 pfflp = (u64)IXGBE_READ_REG(hw, IXGBE_PFFLPL); 734 pfflp |= (u64)IXGBE_READ_REG(hw, IXGBE_PFFLPH) << 32; 735 736 if (enable) 737 pfflp |= (1ULL << pool); 738 else 739 pfflp &= ~(1ULL << pool); 740 741 IXGBE_WRITE_REG(hw, IXGBE_PFFLPL, (u32)pfflp); 742 IXGBE_WRITE_REG(hw, IXGBE_PFFLPH, (u32)(pfflp >> 32)); 743} 744 745/** 746 * ixgbe_set_ethertype_anti_spoofing_X550 - Enable/Disable Ethertype anti-spoofing 747 * @hw: pointer to hardware structure 748 * @enable: enable or disable switch for Ethertype anti-spoofing 749 * @vf: Virtual Function pool - VF Pool to set for Ethertype anti-spoofing 750 * 751 **/ 752void ixgbe_set_ethertype_anti_spoofing_X550(struct ixgbe_hw *hw, 753 bool enable, int vf) 754{ 755 int vf_target_reg = vf >> 3; 756 int vf_target_shift = vf % 8 + IXGBE_SPOOF_ETHERTYPEAS_SHIFT; 757 u32 pfvfspoof; 758 759 DEBUGFUNC("ixgbe_set_ethertype_anti_spoofing_X550"); 760 761 pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg)); 762 if (enable) 763 pfvfspoof |= (1 << vf_target_shift); 764 else 765 pfvfspoof &= ~(1 << vf_target_shift); 766 767 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof); 768} 769 770/** 771 * ixgbe_iosf_wait - Wait for IOSF command completion 772 * @hw: pointer to hardware structure 773 * @ctrl: pointer to location to receive final IOSF control value 774 * 775 * Returns failing status on timeout 776 * 777 * Note: ctrl can be NULL if the IOSF control register value is not needed 778 **/ 779static s32 ixgbe_iosf_wait(struct ixgbe_hw *hw, u32 *ctrl) 780{ 781 u32 i, command = 0; 782 783 /* Check every 10 usec to see if the address cycle completed. 784 * The SB IOSF BUSY bit will clear when the operation is 785 * complete 786 */ 787 for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { 788 command = IXGBE_READ_REG(hw, IXGBE_SB_IOSF_INDIRECT_CTRL); 789 if ((command & IXGBE_SB_IOSF_CTRL_BUSY) == 0) 790 break; 791 usec_delay(10); 792 } 793 if (ctrl) 794 *ctrl = command; 795 if (i == IXGBE_MDIO_COMMAND_TIMEOUT) { 796 ERROR_REPORT1(IXGBE_ERROR_POLLING, "Wait timed out\n"); 797 return IXGBE_ERR_PHY; 798 } 799 800 return IXGBE_SUCCESS; 801} 802 803/** 804 * ixgbe_write_iosf_sb_reg_x550 - Writes a value to specified register of the IOSF 805 * device 806 * @hw: pointer to hardware structure 807 * @reg_addr: 32 bit PHY register to write 808 * @device_type: 3 bit device type 809 * @data: Data to write to the register 810 **/ 811s32 ixgbe_write_iosf_sb_reg_x550(struct ixgbe_hw *hw, u32 reg_addr, 812 u32 device_type, u32 data) 813{ 814 u32 gssr = IXGBE_GSSR_PHY1_SM | IXGBE_GSSR_PHY0_SM; 815 u32 command, error; 816 s32 ret; 817 818 ret = ixgbe_acquire_swfw_semaphore(hw, gssr); 819 if (ret != IXGBE_SUCCESS) 820 return ret; 821 822 ret = ixgbe_iosf_wait(hw, NULL); 823 if (ret != IXGBE_SUCCESS) 824 goto out; 825 826 command = ((reg_addr << IXGBE_SB_IOSF_CTRL_ADDR_SHIFT) | 827 (device_type << IXGBE_SB_IOSF_CTRL_TARGET_SELECT_SHIFT)); 828 829 /* Write IOSF control register */ 830 IXGBE_WRITE_REG(hw, IXGBE_SB_IOSF_INDIRECT_CTRL, command); 831 832 /* Write IOSF data register */ 833 IXGBE_WRITE_REG(hw, IXGBE_SB_IOSF_INDIRECT_DATA, data); 834 835 ret = ixgbe_iosf_wait(hw, &command); 836 837 if ((command & IXGBE_SB_IOSF_CTRL_RESP_STAT_MASK) != 0) { 838 error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >> 839 IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT; 840 ERROR_REPORT2(IXGBE_ERROR_POLLING, 841 "Failed to write, error %x\n", error); 842 ret = IXGBE_ERR_PHY; 843 } 844 845out: 846 ixgbe_release_swfw_semaphore(hw, gssr); 847 return ret; 848} 849 850/** 851 * ixgbe_read_iosf_sb_reg_x550 - Writes a value to specified register of the IOSF 852 * device 853 * @hw: pointer to hardware structure 854 * @reg_addr: 32 bit PHY register to write 855 * @device_type: 3 bit device type 856 * @phy_data: Pointer to read data from the register 857 **/ 858s32 ixgbe_read_iosf_sb_reg_x550(struct ixgbe_hw *hw, u32 reg_addr, 859 u32 device_type, u32 *data) 860{ 861 u32 gssr = IXGBE_GSSR_PHY1_SM | IXGBE_GSSR_PHY0_SM; 862 u32 command, error; 863 s32 ret; 864 865 ret = ixgbe_acquire_swfw_semaphore(hw, gssr); 866 if (ret != IXGBE_SUCCESS) 867 return ret; 868 869 ret = ixgbe_iosf_wait(hw, NULL); 870 if (ret != IXGBE_SUCCESS) 871 goto out; 872 873 command = ((reg_addr << IXGBE_SB_IOSF_CTRL_ADDR_SHIFT) | 874 (device_type << IXGBE_SB_IOSF_CTRL_TARGET_SELECT_SHIFT)); 875 876 /* Write IOSF control register */ 877 IXGBE_WRITE_REG(hw, IXGBE_SB_IOSF_INDIRECT_CTRL, command); 878 879 ret = ixgbe_iosf_wait(hw, &command); 880 881 if ((command & IXGBE_SB_IOSF_CTRL_RESP_STAT_MASK) != 0) { 882 error = (command & IXGBE_SB_IOSF_CTRL_CMPL_ERR_MASK) >> 883 IXGBE_SB_IOSF_CTRL_CMPL_ERR_SHIFT; 884 ERROR_REPORT2(IXGBE_ERROR_POLLING, 885 "Failed to read, error %x\n", error); 886 ret = IXGBE_ERR_PHY; 887 } 888 889 if (ret == IXGBE_SUCCESS) 890 *data = IXGBE_READ_REG(hw, IXGBE_SB_IOSF_INDIRECT_DATA); 891 892out: 893 ixgbe_release_swfw_semaphore(hw, gssr); 894 return ret; 895} 896 897/** 898 * ixgbe_disable_mdd_X550 899 * @hw: pointer to hardware structure 900 * 901 * Disable malicious driver detection 902 **/ 903void ixgbe_disable_mdd_X550(struct ixgbe_hw *hw) 904{ 905 u32 reg; 906 907 DEBUGFUNC("ixgbe_disable_mdd_X550"); 908 909 /* Disable MDD for TX DMA and interrupt */ 910 reg = IXGBE_READ_REG(hw, IXGBE_DMATXCTL); 911 reg &= ~(IXGBE_DMATXCTL_MDP_EN | IXGBE_DMATXCTL_MBINTEN); 912 IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, reg); 913 914 /* Disable MDD for RX and interrupt */ 915 reg = IXGBE_READ_REG(hw, IXGBE_RDRXCTL); 916 reg &= ~(IXGBE_RDRXCTL_MDP_EN | IXGBE_RDRXCTL_MBINTEN); 917 IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, reg); 918} 919 920/** 921 * ixgbe_enable_mdd_X550 922 * @hw: pointer to hardware structure 923 * 924 * Enable malicious driver detection 925 **/ 926void ixgbe_enable_mdd_X550(struct ixgbe_hw *hw) 927{ 928 u32 reg; 929 930 DEBUGFUNC("ixgbe_enable_mdd_X550"); 931 932 /* Enable MDD for TX DMA and interrupt */ 933 reg = IXGBE_READ_REG(hw, IXGBE_DMATXCTL); 934 reg |= (IXGBE_DMATXCTL_MDP_EN | IXGBE_DMATXCTL_MBINTEN); 935 IXGBE_WRITE_REG(hw, IXGBE_DMATXCTL, reg); 936 937 /* Enable MDD for RX and interrupt */ 938 reg = IXGBE_READ_REG(hw, IXGBE_RDRXCTL); 939 reg |= (IXGBE_RDRXCTL_MDP_EN | IXGBE_RDRXCTL_MBINTEN); 940 IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, reg); 941} 942 943/** 944 * ixgbe_restore_mdd_vf_X550 945 * @hw: pointer to hardware structure 946 * @vf: vf index 947 * 948 * Restore VF that was disabled during malicious driver detection event 949 **/ 950void ixgbe_restore_mdd_vf_X550(struct ixgbe_hw *hw, u32 vf) 951{ 952 u32 idx, reg, num_qs, start_q, bitmask; 953 954 DEBUGFUNC("ixgbe_restore_mdd_vf_X550"); 955 956 /* Map VF to queues */ 957 reg = IXGBE_READ_REG(hw, IXGBE_MRQC); 958 switch (reg & IXGBE_MRQC_MRQE_MASK) { 959 case IXGBE_MRQC_VMDQRT8TCEN: 960 num_qs = 8; /* 16 VFs / pools */ 961 bitmask = 0x000000FF; 962 break; 963 case IXGBE_MRQC_VMDQRSS32EN: 964 case IXGBE_MRQC_VMDQRT4TCEN: 965 num_qs = 4; /* 32 VFs / pools */ 966 bitmask = 0x0000000F; 967 break; 968 default: /* 64 VFs / pools */ 969 num_qs = 2; 970 bitmask = 0x00000003; 971 break; 972 } 973 start_q = vf * num_qs; 974 975 /* Release vf's queues by clearing WQBR_TX and WQBR_RX (RW1C) */ 976 idx = start_q / 32; 977 reg = 0; 978 reg |= (bitmask << (start_q % 32)); 979 IXGBE_WRITE_REG(hw, IXGBE_WQBR_TX(idx), reg); 980 IXGBE_WRITE_REG(hw, IXGBE_WQBR_RX(idx), reg); 981} 982 983/** 984 * ixgbe_mdd_event_X550 985 * @hw: pointer to hardware structure 986 * @vf_bitmap: vf bitmap of malicious vfs 987 * 988 * Handle malicious driver detection event. 989 **/ 990void ixgbe_mdd_event_X550(struct ixgbe_hw *hw, u32 *vf_bitmap) 991{ 992 u32 wqbr; 993 u32 i, j, reg, q, shift, vf, idx; 994 995 DEBUGFUNC("ixgbe_mdd_event_X550"); 996 997 /* figure out pool size for mapping to vf's */ 998 reg = IXGBE_READ_REG(hw, IXGBE_MRQC); 999 switch (reg & IXGBE_MRQC_MRQE_MASK) { 1000 case IXGBE_MRQC_VMDQRT8TCEN: 1001 shift = 3; /* 16 VFs / pools */ 1002 break; 1003 case IXGBE_MRQC_VMDQRSS32EN: 1004 case IXGBE_MRQC_VMDQRT4TCEN: 1005 shift = 2; /* 32 VFs / pools */ 1006 break; 1007 default: 1008 shift = 1; /* 64 VFs / pools */ 1009 break; 1010 } 1011 1012 /* Read WQBR_TX and WQBR_RX and check for malicious queues */ 1013 for (i = 0; i < 4; i++) { 1014 wqbr = IXGBE_READ_REG(hw, IXGBE_WQBR_TX(i)); 1015 wqbr |= IXGBE_READ_REG(hw, IXGBE_WQBR_RX(i)); 1016 1017 if (!wqbr) 1018 continue; 1019 1020 /* Get malicious queue */ 1021 for (j = 0; j < 32 && wqbr; j++) { 1022 1023 if (!(wqbr & (1 << j))) 1024 continue; 1025 1026 /* Get queue from bitmask */ 1027 q = j + (i * 32); 1028 1029 /* Map queue to vf */ 1030 vf = (q >> shift); 1031 1032 /* Set vf bit in vf_bitmap */ 1033 idx = vf / 32; 1034 vf_bitmap[idx] |= (1 << (vf % 32)); 1035 wqbr &= ~(1 << j); 1036 } 1037 } 1038} 1039 1040/** 1041 * ixgbe_get_media_type_X550em - Get media type 1042 * @hw: pointer to hardware structure 1043 * 1044 * Returns the media type (fiber, copper, backplane) 1045 */ 1046enum ixgbe_media_type ixgbe_get_media_type_X550em(struct ixgbe_hw *hw) 1047{ 1048 enum ixgbe_media_type media_type; 1049 1050 DEBUGFUNC("ixgbe_get_media_type_X550em"); 1051 1052 /* Detect if there is a copper PHY attached. */ 1053 switch (hw->device_id) { 1054 case IXGBE_DEV_ID_X550EM_X_KR: 1055 case IXGBE_DEV_ID_X550EM_X_KX4: 1056 media_type = ixgbe_media_type_backplane; 1057 break; 1058 case IXGBE_DEV_ID_X550EM_X_SFP: 1059 media_type = ixgbe_media_type_fiber; 1060 break; 1061 case IXGBE_DEV_ID_X550EM_X_1G_T: 1062 case IXGBE_DEV_ID_X550EM_X_10G_T: 1063 media_type = ixgbe_media_type_copper; 1064 break; 1065 default: 1066 media_type = ixgbe_media_type_unknown; 1067 break; 1068 } 1069 return media_type; 1070} 1071 1072/** 1073 * ixgbe_supported_sfp_modules_X550em - Check if SFP module type is supported 1074 * @hw: pointer to hardware structure 1075 * @linear: TRUE if SFP module is linear 1076 */ 1077static s32 ixgbe_supported_sfp_modules_X550em(struct ixgbe_hw *hw, bool *linear) 1078{ 1079 DEBUGFUNC("ixgbe_supported_sfp_modules_X550em"); 1080 1081 switch (hw->phy.sfp_type) { 1082 case ixgbe_sfp_type_not_present: 1083 return IXGBE_ERR_SFP_NOT_PRESENT; 1084 case ixgbe_sfp_type_da_cu_core0: 1085 case ixgbe_sfp_type_da_cu_core1: 1086 *linear = TRUE; 1087 break; 1088 case ixgbe_sfp_type_srlr_core0: 1089 case ixgbe_sfp_type_srlr_core1: 1090 case ixgbe_sfp_type_da_act_lmt_core0: 1091 case ixgbe_sfp_type_da_act_lmt_core1: 1092 case ixgbe_sfp_type_1g_sx_core0: 1093 case ixgbe_sfp_type_1g_sx_core1: 1094 case ixgbe_sfp_type_1g_lx_core0: 1095 case ixgbe_sfp_type_1g_lx_core1: 1096 *linear = FALSE; 1097 break; 1098 case ixgbe_sfp_type_unknown: 1099 case ixgbe_sfp_type_1g_cu_core0: 1100 case ixgbe_sfp_type_1g_cu_core1: 1101 default: 1102 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1103 } 1104 1105 return IXGBE_SUCCESS; 1106} 1107 1108/** 1109 * ixgbe_identify_sfp_module_X550em - Identifies SFP modules 1110 * @hw: pointer to hardware structure 1111 * 1112 * Searches for and identifies the SFP module and assigns appropriate PHY type. 1113 **/ 1114s32 ixgbe_identify_sfp_module_X550em(struct ixgbe_hw *hw) 1115{ 1116 s32 status; 1117 bool linear; 1118 1119 DEBUGFUNC("ixgbe_identify_sfp_module_X550em"); 1120 1121 status = ixgbe_identify_module_generic(hw); 1122 1123 if (status != IXGBE_SUCCESS) 1124 return status; 1125 1126 /* Check if SFP module is supported */ 1127 status = ixgbe_supported_sfp_modules_X550em(hw, &linear); 1128 1129 return status; 1130} 1131 1132/** 1133 * ixgbe_setup_sfp_modules_X550em - Setup MAC link ops 1134 * @hw: pointer to hardware structure 1135 */ 1136s32 ixgbe_setup_sfp_modules_X550em(struct ixgbe_hw *hw) 1137{ 1138 s32 status; 1139 bool linear; 1140 1141 DEBUGFUNC("ixgbe_setup_sfp_modules_X550em"); 1142 1143 /* Check if SFP module is supported */ 1144 status = ixgbe_supported_sfp_modules_X550em(hw, &linear); 1145 1146 if (status != IXGBE_SUCCESS) 1147 return status; 1148 1149 ixgbe_init_mac_link_ops_X550em(hw); 1150 hw->phy.ops.reset = NULL; 1151 1152 return IXGBE_SUCCESS; 1153} 1154 1155/** 1156 * ixgbe_init_mac_link_ops_X550em - init mac link function pointers 1157 * @hw: pointer to hardware structure 1158 */ 1159void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw) 1160{ 1161 struct ixgbe_mac_info *mac = &hw->mac; 1162 1163 DEBUGFUNC("ixgbe_init_mac_link_ops_X550em"); 1164 1165 switch (hw->mac.ops.get_media_type(hw)) { 1166 case ixgbe_media_type_fiber: 1167 /* CS4227 does not support autoneg, so disable the laser control 1168 * functions for SFP+ fiber 1169 */ 1170 mac->ops.disable_tx_laser = NULL; 1171 mac->ops.enable_tx_laser = NULL; 1172 mac->ops.flap_tx_laser = NULL; 1173 mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber; 1174 mac->ops.setup_mac_link = ixgbe_setup_mac_link_sfp_x550em; 1175 mac->ops.set_rate_select_speed = 1176 ixgbe_set_soft_rate_select_speed; 1177 break; 1178 case ixgbe_media_type_copper: 1179 mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em; 1180 mac->ops.check_link = ixgbe_check_link_t_X550em; 1181 break; 1182 default: 1183 break; 1184 } 1185} 1186 1187/** 1188 * ixgbe_get_link_capabilities_x550em - Determines link capabilities 1189 * @hw: pointer to hardware structure 1190 * @speed: pointer to link speed 1191 * @autoneg: TRUE when autoneg or autotry is enabled 1192 */ 1193s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw, 1194 ixgbe_link_speed *speed, 1195 bool *autoneg) 1196{ 1197 DEBUGFUNC("ixgbe_get_link_capabilities_X550em"); 1198 1199 /* SFP */ 1200 if (hw->phy.media_type == ixgbe_media_type_fiber) { 1201 1202 /* CS4227 SFP must not enable auto-negotiation */ 1203 *autoneg = FALSE; 1204 1205 /* Check if 1G SFP module. */ 1206 if (hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 || 1207 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1 1208 || hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 || 1209 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1) { 1210 *speed = IXGBE_LINK_SPEED_1GB_FULL; 1211 return IXGBE_SUCCESS; 1212 } 1213 1214 /* Link capabilities are based on SFP */ 1215 if (hw->phy.multispeed_fiber) 1216 *speed = IXGBE_LINK_SPEED_10GB_FULL | 1217 IXGBE_LINK_SPEED_1GB_FULL; 1218 else 1219 *speed = IXGBE_LINK_SPEED_10GB_FULL; 1220 } else { 1221 *speed = IXGBE_LINK_SPEED_10GB_FULL | 1222 IXGBE_LINK_SPEED_1GB_FULL; 1223 *autoneg = TRUE; 1224 } 1225 1226 return IXGBE_SUCCESS; 1227} 1228 1229/** 1230 * ixgbe_get_lasi_ext_t_x550em - Determime external Base T PHY interrupt cause 1231 * @hw: pointer to hardware structure 1232 * @lsc: pointer to boolean flag which indicates whether external Base T 1233 * PHY interrupt is lsc 1234 * 1235 * Determime if external Base T PHY interrupt cause is high temperature 1236 * failure alarm or link status change. 1237 * 1238 * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature 1239 * failure alarm, else return PHY access status. 1240 */ 1241static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc) 1242{ 1243 u32 status; 1244 u16 reg; 1245 1246 *lsc = FALSE; 1247 1248 /* Vendor alarm triggered */ 1249 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG, 1250 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1251 ®); 1252 1253 if (status != IXGBE_SUCCESS || 1254 !(reg & IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN)) 1255 return status; 1256 1257 /* Vendor Auto-Neg alarm triggered or Global alarm 1 triggered */ 1258 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_FLAG, 1259 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1260 ®); 1261 1262 if (status != IXGBE_SUCCESS || 1263 !(reg & (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN | 1264 IXGBE_MDIO_GLOBAL_ALARM_1_INT))) 1265 return status; 1266 1267 /* Global alarm triggered */ 1268 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_ALARM_1, 1269 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1270 ®); 1271 1272 if (status != IXGBE_SUCCESS) 1273 return status; 1274 1275 /* If high temperature failure, then return over temp error and exit */ 1276 if (reg & IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL) { 1277 /* power down the PHY in case the PHY FW didn't already */ 1278 ixgbe_set_copper_phy_power(hw, FALSE); 1279 return IXGBE_ERR_OVERTEMP; 1280 } else if (reg & IXGBE_MDIO_GLOBAL_ALM_1_DEV_FAULT) { 1281 /* device fault alarm triggered */ 1282 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_FAULT_MSG, 1283 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1284 ®); 1285 1286 if (status != IXGBE_SUCCESS) 1287 return status; 1288 1289 /* if device fault was due to high temp alarm handle and exit */ 1290 if (reg == IXGBE_MDIO_GLOBAL_FAULT_MSG_HI_TMP) { 1291 /* power down the PHY in case the PHY FW didn't */ 1292 ixgbe_set_copper_phy_power(hw, FALSE); 1293 return IXGBE_ERR_OVERTEMP; 1294 } 1295 } 1296 1297 /* Vendor alarm 2 triggered */ 1298 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG, 1299 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®); 1300 1301 if (status != IXGBE_SUCCESS || 1302 !(reg & IXGBE_MDIO_GLOBAL_STD_ALM2_INT)) 1303 return status; 1304 1305 /* link connect/disconnect event occurred */ 1306 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM2, 1307 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®); 1308 1309 if (status != IXGBE_SUCCESS) 1310 return status; 1311 1312 /* Indicate LSC */ 1313 if (reg & IXGBE_MDIO_AUTO_NEG_VEN_LSC) 1314 *lsc = TRUE; 1315 1316 return IXGBE_SUCCESS; 1317} 1318 1319/** 1320 * ixgbe_enable_lasi_ext_t_x550em - Enable external Base T PHY interrupts 1321 * @hw: pointer to hardware structure 1322 * 1323 * Enable link status change and temperature failure alarm for the external 1324 * Base T PHY 1325 * 1326 * Returns PHY access status 1327 */ 1328static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw) 1329{ 1330 u32 status; 1331 u16 reg; 1332 bool lsc; 1333 1334 /* Clear interrupt flags */ 1335 status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc); 1336 1337 /* Enable link status change alarm */ 1338 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, 1339 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®); 1340 1341 if (status != IXGBE_SUCCESS) 1342 return status; 1343 1344 reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN; 1345 1346 status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, 1347 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg); 1348 1349 if (status != IXGBE_SUCCESS) 1350 return status; 1351 1352 /* Enables high temperature failure alarm */ 1353 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK, 1354 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1355 ®); 1356 1357 if (status != IXGBE_SUCCESS) 1358 return status; 1359 1360 reg |= IXGBE_MDIO_GLOBAL_INT_HI_TEMP_EN; 1361 1362 status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK, 1363 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1364 reg); 1365 1366 if (status != IXGBE_SUCCESS) 1367 return status; 1368 1369 /* Enable vendor Auto-Neg alarm and Global Interrupt Mask 1 alarm */ 1370 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK, 1371 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1372 ®); 1373 1374 if (status != IXGBE_SUCCESS) 1375 return status; 1376 1377 reg |= (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN | 1378 IXGBE_MDIO_GLOBAL_ALARM_1_INT); 1379 1380 status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK, 1381 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1382 reg); 1383 1384 if (status != IXGBE_SUCCESS) 1385 return status; 1386 1387 /* Enable chip-wide vendor alarm */ 1388 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK, 1389 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1390 ®); 1391 1392 if (status != IXGBE_SUCCESS) 1393 return status; 1394 1395 reg |= IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN; 1396 1397 status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK, 1398 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1399 reg); 1400 1401 return status; 1402} 1403 1404/** 1405 * ixgbe_setup_kr_speed_x550em - Configure the KR PHY for link speed. 1406 * @hw: pointer to hardware structure 1407 * @speed: link speed 1408 * 1409 * Configures the integrated KR PHY. 1410 **/ 1411static s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *hw, 1412 ixgbe_link_speed speed) 1413{ 1414 s32 status; 1415 u32 reg_val; 1416 1417 status = ixgbe_read_iosf_sb_reg_x550(hw, 1418 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1419 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1420 if (status) 1421 return status; 1422 1423 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE; 1424 reg_val &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR | 1425 IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX); 1426 1427 /* Advertise 10G support. */ 1428 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 1429 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KR; 1430 1431 /* Advertise 1G support. */ 1432 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 1433 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX; 1434 1435 /* Restart auto-negotiation. */ 1436 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART; 1437 status = ixgbe_write_iosf_sb_reg_x550(hw, 1438 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1439 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1440 1441 return status; 1442} 1443 1444/** 1445 * ixgbe_init_phy_ops_X550em - PHY/SFP specific init 1446 * @hw: pointer to hardware structure 1447 * 1448 * Initialize any function pointers that were not able to be 1449 * set during init_shared_code because the PHY/SFP type was 1450 * not known. Perform the SFP init if necessary. 1451 */ 1452s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) 1453{ 1454 struct ixgbe_phy_info *phy = &hw->phy; 1455 ixgbe_link_speed speed; 1456 s32 ret_val; 1457 1458 DEBUGFUNC("ixgbe_init_phy_ops_X550em"); 1459 1460 hw->mac.ops.set_lan_id(hw); 1461 1462 if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) { 1463 phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM; 1464 ixgbe_setup_mux_ctl(hw); 1465 1466 /* Save NW management interface connected on board. This is used 1467 * to determine internal PHY mode. 1468 */ 1469 phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL); 1470 if (phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE) { 1471 speed = IXGBE_LINK_SPEED_10GB_FULL | 1472 IXGBE_LINK_SPEED_1GB_FULL; 1473 } 1474 phy->ops.identify_sfp = ixgbe_identify_sfp_module_X550em; 1475 } 1476 1477 /* Identify the PHY or SFP module */ 1478 ret_val = phy->ops.identify(hw); 1479 if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED) 1480 return ret_val; 1481 1482 /* Setup function pointers based on detected hardware */ 1483 ixgbe_init_mac_link_ops_X550em(hw); 1484 if (phy->sfp_type != ixgbe_sfp_type_unknown) 1485 phy->ops.reset = NULL; 1486 1487 /* Set functions pointers based on phy type */ 1488 switch (hw->phy.type) { 1489 case ixgbe_phy_x550em_kx4: 1490 phy->ops.setup_link = NULL; 1491 phy->ops.read_reg = ixgbe_read_phy_reg_x550em; 1492 phy->ops.write_reg = ixgbe_write_phy_reg_x550em; 1493 break; 1494 case ixgbe_phy_x550em_kr: 1495 phy->ops.setup_link = ixgbe_setup_kr_x550em; 1496 phy->ops.read_reg = ixgbe_read_phy_reg_x550em; 1497 phy->ops.write_reg = ixgbe_write_phy_reg_x550em; 1498 break; 1499 case ixgbe_phy_x550em_ext_t: 1500 /* Save NW management interface connected on board. This is used 1501 * to determine internal PHY mode 1502 */ 1503 phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL); 1504 1505 /* If internal link mode is XFI, then setup iXFI internal link, 1506 * else setup KR now. 1507 */ 1508 if (!(phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { 1509 phy->ops.setup_internal_link = 1510 ixgbe_setup_internal_phy_t_x550em; 1511 } else { 1512 speed = IXGBE_LINK_SPEED_10GB_FULL | 1513 IXGBE_LINK_SPEED_1GB_FULL; 1514 ret_val = ixgbe_setup_kr_speed_x550em(hw, speed); 1515 } 1516 1517 /* setup SW LPLU only for first revision */ 1518 if (!(IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw, 1519 IXGBE_FUSES0_GROUP(0)))) 1520 phy->ops.enter_lplu = ixgbe_enter_lplu_t_x550em; 1521 1522 phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em; 1523 phy->ops.reset = ixgbe_reset_phy_t_X550em; 1524 break; 1525 default: 1526 break; 1527 } 1528 return ret_val; 1529} 1530 1531/** 1532 * ixgbe_reset_hw_X550em - Perform hardware reset 1533 * @hw: pointer to hardware structure 1534 * 1535 * Resets the hardware by resetting the transmit and receive units, masks 1536 * and clears all interrupts, perform a PHY reset, and perform a link (MAC) 1537 * reset. 1538 */ 1539s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw) 1540{ 1541 ixgbe_link_speed link_speed; 1542 s32 status; 1543 u32 ctrl = 0; 1544 u32 i; 1545 u32 hlreg0; 1546 bool link_up = FALSE; 1547 1548 DEBUGFUNC("ixgbe_reset_hw_X550em"); 1549 1550 /* Call adapter stop to disable Tx/Rx and clear interrupts */ 1551 status = hw->mac.ops.stop_adapter(hw); 1552 if (status != IXGBE_SUCCESS) 1553 return status; 1554 1555 /* flush pending Tx transactions */ 1556 ixgbe_clear_tx_pending(hw); 1557 1558 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_10G_T) { 1559 /* Config MDIO clock speed before the first MDIO PHY access */ 1560 hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0); 1561 hlreg0 &= ~IXGBE_HLREG0_MDCSPD; 1562 IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); 1563 } 1564 1565 /* PHY ops must be identified and initialized prior to reset */ 1566 status = hw->phy.ops.init(hw); 1567 1568 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) 1569 return status; 1570 1571 /* start the external PHY */ 1572 if (hw->phy.type == ixgbe_phy_x550em_ext_t) { 1573 status = ixgbe_init_ext_t_x550em(hw); 1574 if (status) 1575 return status; 1576 } 1577 1578 /* Setup SFP module if there is one present. */ 1579 if (hw->phy.sfp_setup_needed) { 1580 status = hw->mac.ops.setup_sfp(hw); 1581 hw->phy.sfp_setup_needed = FALSE; 1582 } 1583 1584 if (status == IXGBE_ERR_SFP_NOT_SUPPORTED) 1585 return status; 1586 1587 /* Reset PHY */ 1588 if (!hw->phy.reset_disable && hw->phy.ops.reset) 1589 hw->phy.ops.reset(hw); 1590 1591mac_reset_top: 1592 /* Issue global reset to the MAC. Needs to be SW reset if link is up. 1593 * If link reset is used when link is up, it might reset the PHY when 1594 * mng is using it. If link is down or the flag to force full link 1595 * reset is set, then perform link reset. 1596 */ 1597 ctrl = IXGBE_CTRL_LNK_RST; 1598 if (!hw->force_full_reset) { 1599 hw->mac.ops.check_link(hw, &link_speed, &link_up, FALSE); 1600 if (link_up) 1601 ctrl = IXGBE_CTRL_RST; 1602 } 1603 1604 ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL); 1605 IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl); 1606 IXGBE_WRITE_FLUSH(hw); 1607 1608 /* Poll for reset bit to self-clear meaning reset is complete */ 1609 for (i = 0; i < 10; i++) { 1610 usec_delay(1); 1611 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); 1612 if (!(ctrl & IXGBE_CTRL_RST_MASK)) 1613 break; 1614 } 1615 1616 if (ctrl & IXGBE_CTRL_RST_MASK) { 1617 status = IXGBE_ERR_RESET_FAILED; 1618 DEBUGOUT("Reset polling failed to complete.\n"); 1619 } 1620 1621 msec_delay(50); 1622 1623 /* Double resets are required for recovery from certain error 1624 * conditions. Between resets, it is necessary to stall to 1625 * allow time for any pending HW events to complete. 1626 */ 1627 if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) { 1628 hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; 1629 goto mac_reset_top; 1630 } 1631 1632 /* Store the permanent mac address */ 1633 hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); 1634 1635 /* Store MAC address from RAR0, clear receive address registers, and 1636 * clear the multicast table. Also reset num_rar_entries to 128, 1637 * since we modify this value when programming the SAN MAC address. 1638 */ 1639 hw->mac.num_rar_entries = 128; 1640 hw->mac.ops.init_rx_addrs(hw); 1641 1642 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP) 1643 ixgbe_setup_mux_ctl(hw); 1644 1645 return status; 1646} 1647 1648/** 1649 * ixgbe_init_ext_t_x550em - Start (unstall) the external Base T PHY. 1650 * @hw: pointer to hardware structure 1651 */ 1652s32 ixgbe_init_ext_t_x550em(struct ixgbe_hw *hw) 1653{ 1654 u32 status; 1655 u16 reg; 1656 1657 status = hw->phy.ops.read_reg(hw, 1658 IXGBE_MDIO_TX_VENDOR_ALARMS_3, 1659 IXGBE_MDIO_PMA_PMD_DEV_TYPE, 1660 ®); 1661 1662 if (status != IXGBE_SUCCESS) 1663 return status; 1664 1665 /* If PHY FW reset completed bit is set then this is the first 1666 * SW instance after a power on so the PHY FW must be un-stalled. 1667 */ 1668 if (reg & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) { 1669 status = hw->phy.ops.read_reg(hw, 1670 IXGBE_MDIO_GLOBAL_RES_PR_10, 1671 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1672 ®); 1673 1674 if (status != IXGBE_SUCCESS) 1675 return status; 1676 1677 reg &= ~IXGBE_MDIO_POWER_UP_STALL; 1678 1679 status = hw->phy.ops.write_reg(hw, 1680 IXGBE_MDIO_GLOBAL_RES_PR_10, 1681 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, 1682 reg); 1683 1684 if (status != IXGBE_SUCCESS) 1685 return status; 1686 } 1687 1688 return status; 1689} 1690 1691/** 1692 * ixgbe_setup_kr_x550em - Configure the KR PHY. 1693 * @hw: pointer to hardware structure 1694 * 1695 * Configures the integrated KR PHY. 1696 **/ 1697s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw) 1698{ 1699 return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised); 1700} 1701 1702/** 1703 * ixgbe_setup_mac_link_sfp_x550em - Setup internal/external the PHY for SFP 1704 * @hw: pointer to hardware structure 1705 * 1706 * Configure the external PHY and the integrated KR PHY for SFP support. 1707 **/ 1708s32 ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw, 1709 ixgbe_link_speed speed, 1710 bool autoneg_wait_to_complete) 1711{ 1712 s32 ret_val; 1713 u16 reg_slice, reg_val; 1714 bool setup_linear = FALSE; 1715 UNREFERENCED_1PARAMETER(autoneg_wait_to_complete); 1716 1717 /* Check if SFP module is supported and linear */ 1718 ret_val = ixgbe_supported_sfp_modules_X550em(hw, &setup_linear); 1719 1720 /* If no SFP module present, then return success. Return success since 1721 * there is no reason to configure CS4227 and SFP not present error is 1722 * not excepted in the setup MAC link flow. 1723 */ 1724 if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT) 1725 return IXGBE_SUCCESS; 1726 1727 if (ret_val != IXGBE_SUCCESS) 1728 return ret_val; 1729 1730 if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { 1731 /* Configure CS4227 LINE side to 10G SR. */ 1732 reg_slice = IXGBE_CS4227_LINE_SPARE22_MSB + 1733 (hw->bus.lan_id << 12); 1734 reg_val = IXGBE_CS4227_SPEED_10G; 1735 ret_val = ixgbe_write_i2c_combined(hw, IXGBE_CS4227, reg_slice, 1736 reg_val); 1737 1738 reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + 1739 (hw->bus.lan_id << 12); 1740 reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; 1741 ret_val = ixgbe_write_i2c_combined(hw, IXGBE_CS4227, reg_slice, 1742 reg_val); 1743 1744 /* Configure CS4227 for HOST connection rate then type. */ 1745 reg_slice = IXGBE_CS4227_HOST_SPARE22_MSB + 1746 (hw->bus.lan_id << 12); 1747 reg_val = (speed & IXGBE_LINK_SPEED_10GB_FULL) ? 1748 IXGBE_CS4227_SPEED_10G : IXGBE_CS4227_SPEED_1G; 1749 ret_val = ixgbe_write_i2c_combined(hw, IXGBE_CS4227, reg_slice, 1750 reg_val); 1751 1752 reg_slice = IXGBE_CS4227_HOST_SPARE24_LSB + 1753 (hw->bus.lan_id << 12); 1754 if (setup_linear) 1755 reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1; 1756 else 1757 reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; 1758 ret_val = ixgbe_write_i2c_combined(hw, IXGBE_CS4227, reg_slice, 1759 reg_val); 1760 1761 /* Setup XFI internal link. */ 1762 ret_val = ixgbe_setup_ixfi_x550em(hw, &speed); 1763 } else { 1764 /* Configure internal PHY for KR/KX. */ 1765 ixgbe_setup_kr_speed_x550em(hw, speed); 1766 1767 /* Configure CS4227 LINE side to proper mode. */ 1768 reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + 1769 (hw->bus.lan_id << 12); 1770 if (setup_linear) 1771 reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1; 1772 else 1773 reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; 1774 ret_val = ixgbe_write_i2c_combined(hw, IXGBE_CS4227, reg_slice, 1775 reg_val); 1776 } 1777 return ret_val; 1778} 1779 1780/** 1781 * ixgbe_setup_ixfi_x550em - Configure the KR PHY for iXFI mode. 1782 * @hw: pointer to hardware structure 1783 * @speed: the link speed to force 1784 * 1785 * Configures the integrated KR PHY to use iXFI mode. Used to connect an 1786 * internal and external PHY at a specific speed, without autonegotiation. 1787 **/ 1788static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed) 1789{ 1790 s32 status; 1791 u32 reg_val; 1792 1793 /* Disable AN and force speed to 10G Serial. */ 1794 status = ixgbe_read_iosf_sb_reg_x550(hw, 1795 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1796 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1797 if (status != IXGBE_SUCCESS) 1798 return status; 1799 1800 reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE; 1801 reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK; 1802 1803 /* Select forced link speed for internal PHY. */ 1804 switch (*speed) { 1805 case IXGBE_LINK_SPEED_10GB_FULL: 1806 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G; 1807 break; 1808 case IXGBE_LINK_SPEED_1GB_FULL: 1809 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G; 1810 break; 1811 default: 1812 /* Other link speeds are not supported by internal KR PHY. */ 1813 return IXGBE_ERR_LINK_SETUP; 1814 } 1815 1816 status = ixgbe_write_iosf_sb_reg_x550(hw, 1817 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1818 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1819 if (status != IXGBE_SUCCESS) 1820 return status; 1821 1822 /* Disable training protocol FSM. */ 1823 status = ixgbe_read_iosf_sb_reg_x550(hw, 1824 IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), 1825 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1826 if (status != IXGBE_SUCCESS) 1827 return status; 1828 reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_CONV_WO_PROTOCOL; 1829 status = ixgbe_write_iosf_sb_reg_x550(hw, 1830 IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), 1831 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1832 if (status != IXGBE_SUCCESS) 1833 return status; 1834 1835 /* Disable Flex from training TXFFE. */ 1836 status = ixgbe_read_iosf_sb_reg_x550(hw, 1837 IXGBE_KRM_DSP_TXFFE_STATE_4(hw->bus.lan_id), 1838 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1839 if (status != IXGBE_SUCCESS) 1840 return status; 1841 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_C0_EN; 1842 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CP1_CN1_EN; 1843 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CO_ADAPT_EN; 1844 status = ixgbe_write_iosf_sb_reg_x550(hw, 1845 IXGBE_KRM_DSP_TXFFE_STATE_4(hw->bus.lan_id), 1846 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1847 if (status != IXGBE_SUCCESS) 1848 return status; 1849 status = ixgbe_read_iosf_sb_reg_x550(hw, 1850 IXGBE_KRM_DSP_TXFFE_STATE_5(hw->bus.lan_id), 1851 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1852 if (status != IXGBE_SUCCESS) 1853 return status; 1854 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_C0_EN; 1855 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CP1_CN1_EN; 1856 reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CO_ADAPT_EN; 1857 status = ixgbe_write_iosf_sb_reg_x550(hw, 1858 IXGBE_KRM_DSP_TXFFE_STATE_5(hw->bus.lan_id), 1859 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1860 if (status != IXGBE_SUCCESS) 1861 return status; 1862 1863 /* Enable override for coefficients. */ 1864 status = ixgbe_read_iosf_sb_reg_x550(hw, 1865 IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id), 1866 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1867 if (status != IXGBE_SUCCESS) 1868 return status; 1869 reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_OVRRD_EN; 1870 reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CZERO_EN; 1871 reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CPLUS1_OVRRD_EN; 1872 reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CMINUS1_OVRRD_EN; 1873 status = ixgbe_write_iosf_sb_reg_x550(hw, 1874 IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id), 1875 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1876 if (status != IXGBE_SUCCESS) 1877 return status; 1878 1879 /* Toggle port SW reset by AN reset. */ 1880 status = ixgbe_read_iosf_sb_reg_x550(hw, 1881 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1882 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 1883 if (status != IXGBE_SUCCESS) 1884 return status; 1885 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART; 1886 status = ixgbe_write_iosf_sb_reg_x550(hw, 1887 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 1888 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 1889 1890 return status; 1891} 1892 1893/** 1894 * ixgbe_ext_phy_t_x550em_get_link - Get ext phy link status 1895 * @hw: address of hardware structure 1896 * @link_up: address of boolean to indicate link status 1897 * 1898 * Returns error code if unable to get link status. 1899 */ 1900static s32 ixgbe_ext_phy_t_x550em_get_link(struct ixgbe_hw *hw, bool *link_up) 1901{ 1902 u32 ret; 1903 u16 autoneg_status; 1904 1905 *link_up = FALSE; 1906 1907 /* read this twice back to back to indicate current status */ 1908 ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, 1909 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 1910 &autoneg_status); 1911 if (ret != IXGBE_SUCCESS) 1912 return ret; 1913 1914 ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, 1915 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 1916 &autoneg_status); 1917 if (ret != IXGBE_SUCCESS) 1918 return ret; 1919 1920 *link_up = !!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS); 1921 1922 return IXGBE_SUCCESS; 1923} 1924 1925/** 1926 * ixgbe_setup_internal_phy_t_x550em - Configure KR PHY to X557 link 1927 * @hw: point to hardware structure 1928 * 1929 * Configures the link between the integrated KR PHY and the external X557 PHY 1930 * The driver will call this function when it gets a link status change 1931 * interrupt from the X557 PHY. This function configures the link speed 1932 * between the PHYs to match the link speed of the BASE-T link. 1933 * 1934 * A return of a non-zero value indicates an error, and the base driver should 1935 * not report link up. 1936 */ 1937s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw) 1938{ 1939 ixgbe_link_speed force_speed; 1940 bool link_up; 1941 u32 status; 1942 u16 speed; 1943 1944 if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) 1945 return IXGBE_ERR_CONFIG; 1946 1947 /* If link is not up, then there is no setup necessary so return */ 1948 status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up); 1949 if (status != IXGBE_SUCCESS) 1950 return status; 1951 1952 if (!link_up) 1953 return IXGBE_SUCCESS; 1954 1955 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT, 1956 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 1957 &speed); 1958 if (status != IXGBE_SUCCESS) 1959 return status; 1960 1961 /* If link is not still up, then no setup is necessary so return */ 1962 status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up); 1963 if (status != IXGBE_SUCCESS) 1964 return status; 1965 if (!link_up) 1966 return IXGBE_SUCCESS; 1967 1968 /* clear everything but the speed and duplex bits */ 1969 speed &= IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK; 1970 1971 switch (speed) { 1972 case IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_FULL: 1973 force_speed = IXGBE_LINK_SPEED_10GB_FULL; 1974 break; 1975 case IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB_FULL: 1976 force_speed = IXGBE_LINK_SPEED_1GB_FULL; 1977 break; 1978 default: 1979 /* Internal PHY does not support anything else */ 1980 return IXGBE_ERR_INVALID_LINK_SETTINGS; 1981 } 1982 1983 return ixgbe_setup_ixfi_x550em(hw, &force_speed); 1984} 1985 1986/** 1987 * ixgbe_setup_phy_loopback_x550em - Configure the KR PHY for loopback. 1988 * @hw: pointer to hardware structure 1989 * 1990 * Configures the integrated KR PHY to use internal loopback mode. 1991 **/ 1992s32 ixgbe_setup_phy_loopback_x550em(struct ixgbe_hw *hw) 1993{ 1994 s32 status; 1995 u32 reg_val; 1996 1997 /* Disable AN and force speed to 10G Serial. */ 1998 status = ixgbe_read_iosf_sb_reg_x550(hw, 1999 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 2000 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 2001 if (status != IXGBE_SUCCESS) 2002 return status; 2003 reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE; 2004 reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK; 2005 reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G; 2006 status = ixgbe_write_iosf_sb_reg_x550(hw, 2007 IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), 2008 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 2009 if (status != IXGBE_SUCCESS) 2010 return status; 2011 2012 /* Set near-end loopback clocks. */ 2013 status = ixgbe_read_iosf_sb_reg_x550(hw, 2014 IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), 2015 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 2016 if (status != IXGBE_SUCCESS) 2017 return status; 2018 reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_32B; 2019 reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_KRPCS; 2020 status = ixgbe_write_iosf_sb_reg_x550(hw, 2021 IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), 2022 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 2023 if (status != IXGBE_SUCCESS) 2024 return status; 2025 2026 /* Set loopback enable. */ 2027 status = ixgbe_read_iosf_sb_reg_x550(hw, 2028 IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), 2029 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 2030 if (status != IXGBE_SUCCESS) 2031 return status; 2032 reg_val |= IXGBE_KRM_PMD_DFX_BURNIN_TX_RX_KR_LB_MASK; 2033 status = ixgbe_write_iosf_sb_reg_x550(hw, 2034 IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), 2035 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 2036 if (status != IXGBE_SUCCESS) 2037 return status; 2038 2039 /* Training bypass. */ 2040 status = ixgbe_read_iosf_sb_reg_x550(hw, 2041 IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), 2042 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 2043 if (status != IXGBE_SUCCESS) 2044 return status; 2045 reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_PROTOCOL_BYPASS; 2046 status = ixgbe_write_iosf_sb_reg_x550(hw, 2047 IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), 2048 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 2049 2050 return status; 2051} 2052 2053/** 2054 * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command 2055 * assuming that the semaphore is already obtained. 2056 * @hw: pointer to hardware structure 2057 * @offset: offset of word in the EEPROM to read 2058 * @data: word read from the EEPROM 2059 * 2060 * Reads a 16 bit word from the EEPROM using the hostif. 2061 **/ 2062s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset, 2063 u16 *data) 2064{ 2065 s32 status; 2066 struct ixgbe_hic_read_shadow_ram buffer; 2067 2068 DEBUGFUNC("ixgbe_read_ee_hostif_data_X550"); 2069 buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD; 2070 buffer.hdr.req.buf_lenh = 0; 2071 buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN; 2072 buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM; 2073 2074 /* convert offset from words to bytes */ 2075 buffer.address = IXGBE_CPU_TO_BE32(offset * 2); 2076 /* one word */ 2077 buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16)); 2078 2079 status = ixgbe_host_interface_command(hw, (u32 *)&buffer, 2080 sizeof(buffer), 2081 IXGBE_HI_COMMAND_TIMEOUT, FALSE); 2082 2083 if (status) 2084 return status; 2085 2086 *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, 2087 FW_NVM_DATA_OFFSET); 2088 2089 return 0; 2090} 2091 2092/** 2093 * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command 2094 * @hw: pointer to hardware structure 2095 * @offset: offset of word in the EEPROM to read 2096 * @data: word read from the EEPROM 2097 * 2098 * Reads a 16 bit word from the EEPROM using the hostif. 2099 **/ 2100s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, 2101 u16 *data) 2102{ 2103 s32 status = IXGBE_SUCCESS; 2104 2105 DEBUGFUNC("ixgbe_read_ee_hostif_X550"); 2106 2107 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) == 2108 IXGBE_SUCCESS) { 2109 status = ixgbe_read_ee_hostif_data_X550(hw, offset, data); 2110 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2111 } else { 2112 status = IXGBE_ERR_SWFW_SYNC; 2113 } 2114 2115 return status; 2116} 2117 2118/** 2119 * ixgbe_read_ee_hostif_buffer_X550- Read EEPROM word(s) using hostif 2120 * @hw: pointer to hardware structure 2121 * @offset: offset of word in the EEPROM to read 2122 * @words: number of words 2123 * @data: word(s) read from the EEPROM 2124 * 2125 * Reads a 16 bit word(s) from the EEPROM using the hostif. 2126 **/ 2127s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, 2128 u16 offset, u16 words, u16 *data) 2129{ 2130 struct ixgbe_hic_read_shadow_ram buffer; 2131 u32 current_word = 0; 2132 u16 words_to_read; 2133 s32 status; 2134 u32 i; 2135 2136 DEBUGFUNC("ixgbe_read_ee_hostif_buffer_X550"); 2137 2138 /* Take semaphore for the entire operation. */ 2139 status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2140 if (status) { 2141 DEBUGOUT("EEPROM read buffer - semaphore failed\n"); 2142 return status; 2143 } 2144 while (words) { 2145 if (words > FW_MAX_READ_BUFFER_SIZE / 2) 2146 words_to_read = FW_MAX_READ_BUFFER_SIZE / 2; 2147 else 2148 words_to_read = words; 2149 2150 buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD; 2151 buffer.hdr.req.buf_lenh = 0; 2152 buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN; 2153 buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM; 2154 2155 /* convert offset from words to bytes */ 2156 buffer.address = IXGBE_CPU_TO_BE32((offset + current_word) * 2); 2157 buffer.length = IXGBE_CPU_TO_BE16(words_to_read * 2); 2158 2159 status = ixgbe_host_interface_command(hw, (u32 *)&buffer, 2160 sizeof(buffer), 2161 IXGBE_HI_COMMAND_TIMEOUT, 2162 FALSE); 2163 2164 if (status) { 2165 DEBUGOUT("Host interface command failed\n"); 2166 goto out; 2167 } 2168 2169 for (i = 0; i < words_to_read; i++) { 2170 u32 reg = IXGBE_FLEX_MNG + (FW_NVM_DATA_OFFSET << 2) + 2171 2 * i; 2172 u32 value = IXGBE_READ_REG(hw, reg); 2173 2174 data[current_word] = (u16)(value & 0xffff); 2175 current_word++; 2176 i++; 2177 if (i < words_to_read) { 2178 value >>= 16; 2179 data[current_word] = (u16)(value & 0xffff); 2180 current_word++; 2181 } 2182 } 2183 words -= words_to_read; 2184 } 2185 2186out: 2187 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2188 return status; 2189} 2190 2191/** 2192 * ixgbe_write_ee_hostif_X550 - Write EEPROM word using hostif 2193 * @hw: pointer to hardware structure 2194 * @offset: offset of word in the EEPROM to write 2195 * @data: word write to the EEPROM 2196 * 2197 * Write a 16 bit word to the EEPROM using the hostif. 2198 **/ 2199s32 ixgbe_write_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset, 2200 u16 data) 2201{ 2202 s32 status; 2203 struct ixgbe_hic_write_shadow_ram buffer; 2204 2205 DEBUGFUNC("ixgbe_write_ee_hostif_data_X550"); 2206 2207 buffer.hdr.req.cmd = FW_WRITE_SHADOW_RAM_CMD; 2208 buffer.hdr.req.buf_lenh = 0; 2209 buffer.hdr.req.buf_lenl = FW_WRITE_SHADOW_RAM_LEN; 2210 buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM; 2211 2212 /* one word */ 2213 buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16)); 2214 buffer.data = data; 2215 buffer.address = IXGBE_CPU_TO_BE32(offset * 2); 2216 2217 status = ixgbe_host_interface_command(hw, (u32 *)&buffer, 2218 sizeof(buffer), 2219 IXGBE_HI_COMMAND_TIMEOUT, FALSE); 2220 2221 return status; 2222} 2223 2224/** 2225 * ixgbe_write_ee_hostif_X550 - Write EEPROM word using hostif 2226 * @hw: pointer to hardware structure 2227 * @offset: offset of word in the EEPROM to write 2228 * @data: word write to the EEPROM 2229 * 2230 * Write a 16 bit word to the EEPROM using the hostif. 2231 **/ 2232s32 ixgbe_write_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, 2233 u16 data) 2234{ 2235 s32 status = IXGBE_SUCCESS; 2236 2237 DEBUGFUNC("ixgbe_write_ee_hostif_X550"); 2238 2239 if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) == 2240 IXGBE_SUCCESS) { 2241 status = ixgbe_write_ee_hostif_data_X550(hw, offset, data); 2242 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2243 } else { 2244 DEBUGOUT("write ee hostif failed to get semaphore"); 2245 status = IXGBE_ERR_SWFW_SYNC; 2246 } 2247 2248 return status; 2249} 2250 2251/** 2252 * ixgbe_write_ee_hostif_buffer_X550 - Write EEPROM word(s) using hostif 2253 * @hw: pointer to hardware structure 2254 * @offset: offset of word in the EEPROM to write 2255 * @words: number of words 2256 * @data: word(s) write to the EEPROM 2257 * 2258 * Write a 16 bit word(s) to the EEPROM using the hostif. 2259 **/ 2260s32 ixgbe_write_ee_hostif_buffer_X550(struct ixgbe_hw *hw, 2261 u16 offset, u16 words, u16 *data) 2262{ 2263 s32 status = IXGBE_SUCCESS; 2264 u32 i = 0; 2265 2266 DEBUGFUNC("ixgbe_write_ee_hostif_buffer_X550"); 2267 2268 /* Take semaphore for the entire operation. */ 2269 status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2270 if (status != IXGBE_SUCCESS) { 2271 DEBUGOUT("EEPROM write buffer - semaphore failed\n"); 2272 goto out; 2273 } 2274 2275 for (i = 0; i < words; i++) { 2276 status = ixgbe_write_ee_hostif_data_X550(hw, offset + i, 2277 data[i]); 2278 2279 if (status != IXGBE_SUCCESS) { 2280 DEBUGOUT("Eeprom buffered write failed\n"); 2281 break; 2282 } 2283 } 2284 2285 hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); 2286out: 2287 2288 return status; 2289} 2290 2291/** 2292 * ixgbe_checksum_ptr_x550 - Checksum one pointer region 2293 * @hw: pointer to hardware structure 2294 * @ptr: pointer offset in eeprom 2295 * @size: size of section pointed by ptr, if 0 first word will be used as size 2296 * @csum: address of checksum to update 2297 * 2298 * Returns error status for any failure 2299 */ 2300static s32 ixgbe_checksum_ptr_x550(struct ixgbe_hw *hw, u16 ptr, 2301 u16 size, u16 *csum, u16 *buffer, 2302 u32 buffer_size) 2303{ 2304 u16 buf[256]; 2305 s32 status; 2306 u16 length, bufsz, i, start; 2307 u16 *local_buffer; 2308 2309 bufsz = sizeof(buf) / sizeof(buf[0]); 2310 2311 /* Read a chunk at the pointer location */ 2312 if (!buffer) { 2313 status = ixgbe_read_ee_hostif_buffer_X550(hw, ptr, bufsz, buf); 2314 if (status) { 2315 DEBUGOUT("Failed to read EEPROM image\n"); 2316 return status; 2317 } 2318 local_buffer = buf; 2319 } else { 2320 if (buffer_size < ptr) 2321 return IXGBE_ERR_PARAM; 2322 local_buffer = &buffer[ptr]; 2323 } 2324 2325 if (size) { 2326 start = 0; 2327 length = size; 2328 } else { 2329 start = 1; 2330 length = local_buffer[0]; 2331 2332 /* Skip pointer section if length is invalid. */ 2333 if (length == 0xFFFF || length == 0 || 2334 (ptr + length) >= hw->eeprom.word_size) 2335 return IXGBE_SUCCESS; 2336 } 2337 2338 if (buffer && ((u32)start + (u32)length > buffer_size)) 2339 return IXGBE_ERR_PARAM; 2340 2341 for (i = start; length; i++, length--) { 2342 if (i == bufsz && !buffer) { 2343 ptr += bufsz; 2344 i = 0; 2345 if (length < bufsz) 2346 bufsz = length; 2347 2348 /* Read a chunk at the pointer location */ 2349 status = ixgbe_read_ee_hostif_buffer_X550(hw, ptr, 2350 bufsz, buf); 2351 if (status) { 2352 DEBUGOUT("Failed to read EEPROM image\n"); 2353 return status; 2354 } 2355 } 2356 *csum += local_buffer[i]; 2357 } 2358 return IXGBE_SUCCESS; 2359} 2360 2361/** 2362 * ixgbe_calc_checksum_X550 - Calculates and returns the checksum 2363 * @hw: pointer to hardware structure 2364 * @buffer: pointer to buffer containing calculated checksum 2365 * @buffer_size: size of buffer 2366 * 2367 * Returns a negative error code on error, or the 16-bit checksum 2368 **/ 2369s32 ixgbe_calc_checksum_X550(struct ixgbe_hw *hw, u16 *buffer, u32 buffer_size) 2370{ 2371 u16 eeprom_ptrs[IXGBE_EEPROM_LAST_WORD + 1]; 2372 u16 *local_buffer; 2373 s32 status; 2374 u16 checksum = 0; 2375 u16 pointer, i, size; 2376 2377 DEBUGFUNC("ixgbe_calc_eeprom_checksum_X550"); 2378 2379 hw->eeprom.ops.init_params(hw); 2380 2381 if (!buffer) { 2382 /* Read pointer area */ 2383 status = ixgbe_read_ee_hostif_buffer_X550(hw, 0, 2384 IXGBE_EEPROM_LAST_WORD + 1, 2385 eeprom_ptrs); 2386 if (status) { 2387 DEBUGOUT("Failed to read EEPROM image\n"); 2388 return status; 2389 } 2390 local_buffer = eeprom_ptrs; 2391 } else { 2392 if (buffer_size < IXGBE_EEPROM_LAST_WORD) 2393 return IXGBE_ERR_PARAM; 2394 local_buffer = buffer; 2395 } 2396 2397 /* 2398 * For X550 hardware include 0x0-0x41 in the checksum, skip the 2399 * checksum word itself 2400 */ 2401 for (i = 0; i <= IXGBE_EEPROM_LAST_WORD; i++) 2402 if (i != IXGBE_EEPROM_CHECKSUM) 2403 checksum += local_buffer[i]; 2404 2405 /* 2406 * Include all data from pointers 0x3, 0x6-0xE. This excludes the 2407 * FW, PHY module, and PCIe Expansion/Option ROM pointers. 2408 */ 2409 for (i = IXGBE_PCIE_ANALOG_PTR_X550; i < IXGBE_FW_PTR; i++) { 2410 if (i == IXGBE_PHY_PTR || i == IXGBE_OPTION_ROM_PTR) 2411 continue; 2412 2413 pointer = local_buffer[i]; 2414 2415 /* Skip pointer section if the pointer is invalid. */ 2416 if (pointer == 0xFFFF || pointer == 0 || 2417 pointer >= hw->eeprom.word_size) 2418 continue; 2419 2420 switch (i) { 2421 case IXGBE_PCIE_GENERAL_PTR: 2422 size = IXGBE_IXGBE_PCIE_GENERAL_SIZE; 2423 break; 2424 case IXGBE_PCIE_CONFIG0_PTR: 2425 case IXGBE_PCIE_CONFIG1_PTR: 2426 size = IXGBE_PCIE_CONFIG_SIZE; 2427 break; 2428 default: 2429 size = 0; 2430 break; 2431 } 2432 2433 status = ixgbe_checksum_ptr_x550(hw, pointer, size, &checksum, 2434 buffer, buffer_size); 2435 if (status) 2436 return status; 2437 } 2438 2439 checksum = (u16)IXGBE_EEPROM_SUM - checksum; 2440 2441 return (s32)checksum; 2442} 2443 2444/** 2445 * ixgbe_calc_eeprom_checksum_X550 - Calculates and returns the checksum 2446 * @hw: pointer to hardware structure 2447 * 2448 * Returns a negative error code on error, or the 16-bit checksum 2449 **/ 2450s32 ixgbe_calc_eeprom_checksum_X550(struct ixgbe_hw *hw) 2451{ 2452 return ixgbe_calc_checksum_X550(hw, NULL, 0); 2453} 2454 2455/** 2456 * ixgbe_validate_eeprom_checksum_X550 - Validate EEPROM checksum 2457 * @hw: pointer to hardware structure 2458 * @checksum_val: calculated checksum 2459 * 2460 * Performs checksum calculation and validates the EEPROM checksum. If the 2461 * caller does not need checksum_val, the value can be NULL. 2462 **/ 2463s32 ixgbe_validate_eeprom_checksum_X550(struct ixgbe_hw *hw, u16 *checksum_val) 2464{ 2465 s32 status; 2466 u16 checksum; 2467 u16 read_checksum = 0; 2468 2469 DEBUGFUNC("ixgbe_validate_eeprom_checksum_X550"); 2470 2471 /* Read the first word from the EEPROM. If this times out or fails, do 2472 * not continue or we could be in for a very long wait while every 2473 * EEPROM read fails 2474 */ 2475 status = hw->eeprom.ops.read(hw, 0, &checksum); 2476 if (status) { 2477 DEBUGOUT("EEPROM read failed\n"); 2478 return status; 2479 } 2480 2481 status = hw->eeprom.ops.calc_checksum(hw); 2482 if (status < 0) 2483 return status; 2484 2485 checksum = (u16)(status & 0xffff); 2486 2487 status = ixgbe_read_ee_hostif_X550(hw, IXGBE_EEPROM_CHECKSUM, 2488 &read_checksum); 2489 if (status) 2490 return status; 2491 2492 /* Verify read checksum from EEPROM is the same as 2493 * calculated checksum 2494 */ 2495 if (read_checksum != checksum) { 2496 status = IXGBE_ERR_EEPROM_CHECKSUM; 2497 ERROR_REPORT1(IXGBE_ERROR_INVALID_STATE, 2498 "Invalid EEPROM checksum"); 2499 } 2500 2501 /* If the user cares, return the calculated checksum */ 2502 if (checksum_val) 2503 *checksum_val = checksum; 2504 2505 return status; 2506} 2507 2508/** 2509 * ixgbe_update_eeprom_checksum_X550 - Updates the EEPROM checksum and flash 2510 * @hw: pointer to hardware structure 2511 * 2512 * After writing EEPROM to shadow RAM using EEWR register, software calculates 2513 * checksum and updates the EEPROM and instructs the hardware to update 2514 * the flash. 2515 **/ 2516s32 ixgbe_update_eeprom_checksum_X550(struct ixgbe_hw *hw) 2517{ 2518 s32 status; 2519 u16 checksum = 0; 2520 2521 DEBUGFUNC("ixgbe_update_eeprom_checksum_X550"); 2522 2523 /* Read the first word from the EEPROM. If this times out or fails, do 2524 * not continue or we could be in for a very long wait while every 2525 * EEPROM read fails 2526 */ 2527 status = ixgbe_read_ee_hostif_X550(hw, 0, &checksum); 2528 if (status) { 2529 DEBUGOUT("EEPROM read failed\n"); 2530 return status; 2531 } 2532 2533 status = ixgbe_calc_eeprom_checksum_X550(hw); 2534 if (status < 0) 2535 return status; 2536 2537 checksum = (u16)(status & 0xffff); 2538 2539 status = ixgbe_write_ee_hostif_X550(hw, IXGBE_EEPROM_CHECKSUM, 2540 checksum); 2541 if (status) 2542 return status; 2543 2544 status = ixgbe_update_flash_X550(hw); 2545 2546 return status; 2547} 2548 2549/** 2550 * ixgbe_update_flash_X550 - Instruct HW to copy EEPROM to Flash device 2551 * @hw: pointer to hardware structure 2552 * 2553 * Issue a shadow RAM dump to FW to copy EEPROM from shadow RAM to the flash. 2554 **/ 2555s32 ixgbe_update_flash_X550(struct ixgbe_hw *hw) 2556{ 2557 s32 status = IXGBE_SUCCESS; 2558 union ixgbe_hic_hdr2 buffer; 2559 2560 DEBUGFUNC("ixgbe_update_flash_X550"); 2561 2562 buffer.req.cmd = FW_SHADOW_RAM_DUMP_CMD; 2563 buffer.req.buf_lenh = 0; 2564 buffer.req.buf_lenl = FW_SHADOW_RAM_DUMP_LEN; 2565 buffer.req.checksum = FW_DEFAULT_CHECKSUM; 2566 2567 status = ixgbe_host_interface_command(hw, (u32 *)&buffer, 2568 sizeof(buffer), 2569 IXGBE_HI_COMMAND_TIMEOUT, FALSE); 2570 2571 return status; 2572} 2573 2574/** 2575 * ixgbe_get_supported_physical_layer_X550em - Returns physical layer type 2576 * @hw: pointer to hardware structure 2577 * 2578 * Determines physical layer capabilities of the current configuration. 2579 **/ 2580u32 ixgbe_get_supported_physical_layer_X550em(struct ixgbe_hw *hw) 2581{ 2582 u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; 2583 u16 ext_ability = 0; 2584 2585 DEBUGFUNC("ixgbe_get_supported_physical_layer_X550em"); 2586 2587 hw->phy.ops.identify(hw); 2588 2589 switch (hw->phy.type) { 2590 case ixgbe_phy_x550em_kr: 2591 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR | 2592 IXGBE_PHYSICAL_LAYER_1000BASE_KX; 2593 break; 2594 case ixgbe_phy_x550em_kx4: 2595 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4 | 2596 IXGBE_PHYSICAL_LAYER_1000BASE_KX; 2597 break; 2598 case ixgbe_phy_x550em_ext_t: 2599 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY, 2600 IXGBE_MDIO_PMA_PMD_DEV_TYPE, 2601 &ext_ability); 2602 if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY) 2603 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T; 2604 if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY) 2605 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; 2606 break; 2607 default: 2608 break; 2609 } 2610 2611 if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) 2612 physical_layer = ixgbe_get_supported_phy_sfp_layer_generic(hw); 2613 2614 return physical_layer; 2615} 2616 2617/** 2618 * ixgbe_get_bus_info_x550em - Set PCI bus info 2619 * @hw: pointer to hardware structure 2620 * 2621 * Sets bus link width and speed to unknown because X550em is 2622 * not a PCI device. 2623 **/ 2624s32 ixgbe_get_bus_info_X550em(struct ixgbe_hw *hw) 2625{ 2626 2627 DEBUGFUNC("ixgbe_get_bus_info_x550em"); 2628 2629 hw->bus.width = ixgbe_bus_width_unknown; 2630 hw->bus.speed = ixgbe_bus_speed_unknown; 2631 2632 hw->mac.ops.set_lan_id(hw); 2633 2634 return IXGBE_SUCCESS; 2635} 2636 2637/** 2638 * ixgbe_disable_rx_x550 - Disable RX unit 2639 * 2640 * Enables the Rx DMA unit for x550 2641 **/ 2642void ixgbe_disable_rx_x550(struct ixgbe_hw *hw) 2643{ 2644 u32 rxctrl, pfdtxgswc; 2645 s32 status; 2646 struct ixgbe_hic_disable_rxen fw_cmd; 2647 2648 DEBUGFUNC("ixgbe_enable_rx_dma_x550"); 2649 2650 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 2651 if (rxctrl & IXGBE_RXCTRL_RXEN) { 2652 pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC); 2653 if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) { 2654 pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN; 2655 IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc); 2656 hw->mac.set_lben = TRUE; 2657 } else { 2658 hw->mac.set_lben = FALSE; 2659 } 2660 2661 fw_cmd.hdr.cmd = FW_DISABLE_RXEN_CMD; 2662 fw_cmd.hdr.buf_len = FW_DISABLE_RXEN_LEN; 2663 fw_cmd.hdr.checksum = FW_DEFAULT_CHECKSUM; 2664 fw_cmd.port_number = (u8)hw->bus.lan_id; 2665 2666 status = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd, 2667 sizeof(struct ixgbe_hic_disable_rxen), 2668 IXGBE_HI_COMMAND_TIMEOUT, TRUE); 2669 2670 /* If we fail - disable RX using register write */ 2671 if (status) { 2672 rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL); 2673 if (rxctrl & IXGBE_RXCTRL_RXEN) { 2674 rxctrl &= ~IXGBE_RXCTRL_RXEN; 2675 IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl); 2676 } 2677 } 2678 } 2679} 2680 2681/** 2682 * ixgbe_enter_lplu_x550em - Transition to low power states 2683 * @hw: pointer to hardware structure 2684 * 2685 * Configures Low Power Link Up on transition to low power states 2686 * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the 2687 * X557 PHY immediately prior to entering LPLU. 2688 **/ 2689s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw) 2690{ 2691 u16 an_10g_cntl_reg, autoneg_reg, speed; 2692 s32 status; 2693 ixgbe_link_speed lcd_speed; 2694 u32 save_autoneg; 2695 bool link_up; 2696 2697 /* SW LPLU not required on later HW revisions. */ 2698 if (IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))) 2699 return IXGBE_SUCCESS; 2700 2701 /* If blocked by MNG FW, then don't restart AN */ 2702 if (ixgbe_check_reset_blocked(hw)) 2703 return IXGBE_SUCCESS; 2704 2705 status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up); 2706 if (status != IXGBE_SUCCESS) 2707 return status; 2708 2709 status = ixgbe_read_eeprom(hw, NVM_INIT_CTRL_3, &hw->eeprom.ctrl_word_3); 2710 2711 if (status != IXGBE_SUCCESS) 2712 return status; 2713 2714 /* If link is down, LPLU disabled in NVM, WoL disabled, or manageability 2715 * disabled, then force link down by entering low power mode. 2716 */ 2717 if (!link_up || !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) || 2718 !(hw->wol_enabled || ixgbe_mng_present(hw))) 2719 return ixgbe_set_copper_phy_power(hw, FALSE); 2720 2721 /* Determine LCD */ 2722 status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed); 2723 2724 if (status != IXGBE_SUCCESS) 2725 return status; 2726 2727 /* If no valid LCD link speed, then force link down and exit. */ 2728 if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN) 2729 return ixgbe_set_copper_phy_power(hw, FALSE); 2730 2731 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT, 2732 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2733 &speed); 2734 2735 if (status != IXGBE_SUCCESS) 2736 return status; 2737 2738 /* If no link now, speed is invalid so take link down */ 2739 status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up); 2740 if (status != IXGBE_SUCCESS) 2741 return ixgbe_set_copper_phy_power(hw, FALSE); 2742 2743 /* clear everything but the speed bits */ 2744 speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK; 2745 2746 /* If current speed is already LCD, then exit. */ 2747 if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) && 2748 (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) || 2749 ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) && 2750 (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL))) 2751 return status; 2752 2753 /* Clear AN completed indication */ 2754 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM, 2755 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2756 &autoneg_reg); 2757 2758 if (status != IXGBE_SUCCESS) 2759 return status; 2760 2761 status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG, 2762 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2763 &an_10g_cntl_reg); 2764 2765 if (status != IXGBE_SUCCESS) 2766 return status; 2767 2768 status = hw->phy.ops.read_reg(hw, 2769 IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG, 2770 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2771 &autoneg_reg); 2772 2773 if (status != IXGBE_SUCCESS) 2774 return status; 2775 2776 save_autoneg = hw->phy.autoneg_advertised; 2777 2778 /* Setup link at least common link speed */ 2779 status = hw->mac.ops.setup_link(hw, lcd_speed, FALSE); 2780 2781 /* restore autoneg from before setting lplu speed */ 2782 hw->phy.autoneg_advertised = save_autoneg; 2783 2784 return status; 2785} 2786 2787/** 2788 * ixgbe_get_lcd_x550em - Determine lowest common denominator 2789 * @hw: pointer to hardware structure 2790 * @lcd_speed: pointer to lowest common link speed 2791 * 2792 * Determine lowest common link speed with link partner. 2793 **/ 2794s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *lcd_speed) 2795{ 2796 u16 an_lp_status; 2797 s32 status; 2798 u16 word = hw->eeprom.ctrl_word_3; 2799 2800 *lcd_speed = IXGBE_LINK_SPEED_UNKNOWN; 2801 2802 status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS, 2803 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 2804 &an_lp_status); 2805 2806 if (status != IXGBE_SUCCESS) 2807 return status; 2808 2809 /* If link partner advertised 1G, return 1G */ 2810 if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) { 2811 *lcd_speed = IXGBE_LINK_SPEED_1GB_FULL; 2812 return status; 2813 } 2814 2815 /* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */ 2816 if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) || 2817 (word & NVM_INIT_CTRL_3_D10GMP_PORT0)) 2818 return status; 2819 2820 /* Link partner not capable of lower speeds, return 10G */ 2821 *lcd_speed = IXGBE_LINK_SPEED_10GB_FULL; 2822 return status; 2823} 2824 2825/** 2826 * ixgbe_setup_fc_X550em - Set up flow control 2827 * @hw: pointer to hardware structure 2828 * 2829 * Called at init time to set up flow control. 2830 **/ 2831s32 ixgbe_setup_fc_X550em(struct ixgbe_hw *hw) 2832{ 2833 s32 ret_val = IXGBE_SUCCESS; 2834 u32 pause, asm_dir, reg_val; 2835 2836 DEBUGFUNC("ixgbe_setup_fc_X550em"); 2837 2838 /* Validate the requested mode */ 2839 if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { 2840 ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, 2841 "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); 2842 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 2843 goto out; 2844 } 2845 2846 /* 10gig parts do not have a word in the EEPROM to determine the 2847 * default flow control setting, so we explicitly set it to full. 2848 */ 2849 if (hw->fc.requested_mode == ixgbe_fc_default) 2850 hw->fc.requested_mode = ixgbe_fc_full; 2851 2852 /* Determine PAUSE and ASM_DIR bits. */ 2853 switch (hw->fc.requested_mode) { 2854 case ixgbe_fc_none: 2855 pause = 0; 2856 asm_dir = 0; 2857 break; 2858 case ixgbe_fc_tx_pause: 2859 pause = 0; 2860 asm_dir = 1; 2861 break; 2862 case ixgbe_fc_rx_pause: 2863 /* Rx Flow control is enabled and Tx Flow control is 2864 * disabled by software override. Since there really 2865 * isn't a way to advertise that we are capable of RX 2866 * Pause ONLY, we will advertise that we support both 2867 * symmetric and asymmetric Rx PAUSE, as such we fall 2868 * through to the fc_full statement. Later, we will 2869 * disable the adapter's ability to send PAUSE frames. 2870 */ 2871 case ixgbe_fc_full: 2872 pause = 1; 2873 asm_dir = 1; 2874 break; 2875 default: 2876 ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, 2877 "Flow control param set incorrectly\n"); 2878 ret_val = IXGBE_ERR_CONFIG; 2879 goto out; 2880 } 2881 2882 if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) { 2883 ret_val = ixgbe_read_iosf_sb_reg_x550(hw, 2884 IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), 2885 IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); 2886 if (ret_val != IXGBE_SUCCESS) 2887 goto out; 2888 reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE | 2889 IXGBE_KRM_AN_CNTL_1_ASM_PAUSE); 2890 if (pause) 2891 reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE; 2892 if (asm_dir) 2893 reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE; 2894 ret_val = ixgbe_write_iosf_sb_reg_x550(hw, 2895 IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), 2896 IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); 2897 2898 /* This device does not fully support AN. */ 2899 hw->fc.disable_fc_autoneg = TRUE; 2900 } 2901 2902out: 2903 return ret_val; 2904} 2905 2906/** 2907 * ixgbe_set_mux - Set mux for port 1 access with CS4227 2908 * @hw: pointer to hardware structure 2909 * @state: set mux if 1, clear if 0 2910 */ 2911static void ixgbe_set_mux(struct ixgbe_hw *hw, u8 state) 2912{ 2913 u32 esdp; 2914 2915 if (!hw->bus.lan_id) 2916 return; 2917 esdp = IXGBE_READ_REG(hw, IXGBE_ESDP); 2918 if (state) 2919 esdp |= IXGBE_ESDP_SDP1; 2920 else 2921 esdp &= ~IXGBE_ESDP_SDP1; 2922 IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp); 2923 IXGBE_WRITE_FLUSH(hw); 2924} 2925 2926/** 2927 * ixgbe_acquire_swfw_sync_X550em - Acquire SWFW semaphore 2928 * @hw: pointer to hardware structure 2929 * @mask: Mask to specify which semaphore to acquire 2930 * 2931 * Acquires the SWFW semaphore and sets the I2C MUX 2932 **/ 2933s32 ixgbe_acquire_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask) 2934{ 2935 s32 status; 2936 2937 DEBUGFUNC("ixgbe_acquire_swfw_sync_X550em"); 2938 2939 status = ixgbe_acquire_swfw_sync_X540(hw, mask); 2940 if (status) 2941 return status; 2942 2943 if (mask & IXGBE_GSSR_I2C_MASK) 2944 ixgbe_set_mux(hw, 1); 2945 2946 return IXGBE_SUCCESS; 2947} 2948 2949/** 2950 * ixgbe_release_swfw_sync_X550em - Release SWFW semaphore 2951 * @hw: pointer to hardware structure 2952 * @mask: Mask to specify which semaphore to release 2953 * 2954 * Releases the SWFW semaphore and sets the I2C MUX 2955 **/ 2956void ixgbe_release_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask) 2957{ 2958 DEBUGFUNC("ixgbe_release_swfw_sync_X550em"); 2959 2960 if (mask & IXGBE_GSSR_I2C_MASK) 2961 ixgbe_set_mux(hw, 0); 2962 2963 ixgbe_release_swfw_sync_X540(hw, mask); 2964} 2965 2966/** 2967 * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt 2968 * @hw: pointer to hardware structure 2969 * 2970 * Handle external Base T PHY interrupt. If high temperature 2971 * failure alarm then return error, else if link status change 2972 * then setup internal/external PHY link 2973 * 2974 * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature 2975 * failure alarm, else return PHY access status. 2976 */ 2977s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw) 2978{ 2979 bool lsc; 2980 u32 status; 2981 2982 status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc); 2983 2984 if (status != IXGBE_SUCCESS) 2985 return status; 2986 2987 if (lsc) 2988 return ixgbe_setup_internal_phy(hw); 2989 2990 return IXGBE_SUCCESS; 2991} 2992 2993/** 2994 * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed 2995 * @hw: pointer to hardware structure 2996 * @speed: new link speed 2997 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 2998 * 2999 * Setup internal/external PHY link speed based on link speed, then set 3000 * external PHY auto advertised link speed. 3001 * 3002 * Returns error status for any failure 3003 **/ 3004s32 ixgbe_setup_mac_link_t_X550em(struct ixgbe_hw *hw, 3005 ixgbe_link_speed speed, 3006 bool autoneg_wait_to_complete) 3007{ 3008 s32 status; 3009 ixgbe_link_speed force_speed; 3010 3011 DEBUGFUNC("ixgbe_setup_mac_link_t_X550em"); 3012 3013 /* Setup internal/external PHY link speed to iXFI (10G), unless 3014 * only 1G is auto advertised then setup KX link. 3015 */ 3016 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 3017 force_speed = IXGBE_LINK_SPEED_10GB_FULL; 3018 else 3019 force_speed = IXGBE_LINK_SPEED_1GB_FULL; 3020 3021 /* If internal link mode is XFI, then setup XFI internal link. */ 3022 if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { 3023 status = ixgbe_setup_ixfi_x550em(hw, &force_speed); 3024 3025 if (status != IXGBE_SUCCESS) 3026 return status; 3027 } 3028 3029 return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait_to_complete); 3030} 3031 3032/** 3033 * ixgbe_check_link_t_X550em - Determine link and speed status 3034 * @hw: pointer to hardware structure 3035 * @speed: pointer to link speed 3036 * @link_up: TRUE when link is up 3037 * @link_up_wait_to_complete: bool used to wait for link up or not 3038 * 3039 * Check that both the MAC and X557 external PHY have link. 3040 **/ 3041s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed, 3042 bool *link_up, bool link_up_wait_to_complete) 3043{ 3044 u32 status; 3045 u16 autoneg_status; 3046 3047 if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) 3048 return IXGBE_ERR_CONFIG; 3049 3050 status = ixgbe_check_mac_link_generic(hw, speed, link_up, 3051 link_up_wait_to_complete); 3052 3053 /* If check link fails or MAC link is not up, then return */ 3054 if (status != IXGBE_SUCCESS || !(*link_up)) 3055 return status; 3056 3057 /* MAC link is up, so check external PHY link. 3058 * Read this twice back to back to indicate current status. 3059 */ 3060 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, 3061 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 3062 &autoneg_status); 3063 3064 if (status != IXGBE_SUCCESS) 3065 return status; 3066 3067 status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, 3068 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, 3069 &autoneg_status); 3070 3071 if (status != IXGBE_SUCCESS) 3072 return status; 3073 3074 /* If external PHY link is not up, then indicate link not up */ 3075 if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS)) 3076 *link_up = FALSE; 3077 3078 return IXGBE_SUCCESS; 3079} 3080 3081/** 3082 * ixgbe_reset_phy_t_X550em - Performs X557 PHY reset and enables LASI 3083 * @hw: pointer to hardware structure 3084 **/ 3085s32 ixgbe_reset_phy_t_X550em(struct ixgbe_hw *hw) 3086{ 3087 s32 status; 3088 3089 status = ixgbe_reset_phy_generic(hw); 3090 3091 if (status != IXGBE_SUCCESS) 3092 return status; 3093 3094 /* Configure Link Status Alarm and Temperature Threshold interrupts */ 3095 return ixgbe_enable_lasi_ext_t_x550em(hw); 3096} 3097 3098/** 3099 * ixgbe_led_on_t_X550em - Turns on the software controllable LEDs. 3100 * @hw: pointer to hardware structure 3101 * @led_idx: led number to turn on 3102 **/ 3103s32 ixgbe_led_on_t_X550em(struct ixgbe_hw *hw, u32 led_idx) 3104{ 3105 u16 phy_data; 3106 3107 DEBUGFUNC("ixgbe_led_on_t_X550em"); 3108 3109 if (led_idx >= IXGBE_X557_MAX_LED_INDEX) 3110 return IXGBE_ERR_PARAM; 3111 3112 /* To turn on the LED, set mode to ON. */ 3113 ixgbe_read_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, 3114 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, &phy_data); 3115 phy_data |= IXGBE_X557_LED_MANUAL_SET_MASK; 3116 ixgbe_write_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, 3117 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, phy_data); 3118 3119 return IXGBE_SUCCESS; 3120} 3121 3122/** 3123 * ixgbe_led_off_t_X550em - Turns off the software controllable LEDs. 3124 * @hw: pointer to hardware structure 3125 * @led_idx: led number to turn off 3126 **/ 3127s32 ixgbe_led_off_t_X550em(struct ixgbe_hw *hw, u32 led_idx) 3128{ 3129 u16 phy_data; 3130 3131 DEBUGFUNC("ixgbe_led_off_t_X550em"); 3132 3133 if (led_idx >= IXGBE_X557_MAX_LED_INDEX) 3134 return IXGBE_ERR_PARAM; 3135 3136 /* To turn on the LED, set mode to ON. */ 3137 ixgbe_read_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, 3138 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, &phy_data); 3139 phy_data &= ~IXGBE_X557_LED_MANUAL_SET_MASK; 3140 ixgbe_write_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx, 3141 IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, phy_data); 3142 3143 return IXGBE_SUCCESS; 3144} 3145 3146