1/* sunzilog.c: Zilog serial driver for Sparc systems. 2 * 3 * Driver for Zilog serial chips found on Sun workstations and 4 * servers. This driver could actually be made more generic. 5 * 6 * This is based on the old drivers/sbus/char/zs.c code. A lot 7 * of code has been simply moved over directly from there but 8 * much has been rewritten. Credits therefore go out to Eddie 9 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their 10 * work there. 11 * 12 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net) 13 */ 14 15#include <linux/module.h> 16#include <linux/kernel.h> 17#include <linux/errno.h> 18#include <linux/delay.h> 19#include <linux/tty.h> 20#include <linux/tty_flip.h> 21#include <linux/major.h> 22#include <linux/string.h> 23#include <linux/ptrace.h> 24#include <linux/ioport.h> 25#include <linux/slab.h> 26#include <linux/circ_buf.h> 27#include <linux/serial.h> 28#include <linux/sysrq.h> 29#include <linux/console.h> 30#include <linux/spinlock.h> 31#ifdef CONFIG_SERIO 32#include <linux/serio.h> 33#endif 34#include <linux/init.h> 35#include <linux/of_device.h> 36 37#include <asm/io.h> 38#include <asm/irq.h> 39#include <asm/prom.h> 40 41#if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 42#define SUPPORT_SYSRQ 43#endif 44 45#include <linux/serial_core.h> 46 47#include "suncore.h" 48#include "sunzilog.h" 49 50/* On 32-bit sparcs we need to delay after register accesses 51 * to accommodate sun4 systems, but we do not need to flush writes. 52 * On 64-bit sparc we only need to flush single writes to ensure 53 * completion. 54 */ 55#ifndef CONFIG_SPARC64 56#define ZSDELAY() udelay(5) 57#define ZSDELAY_LONG() udelay(20) 58#define ZS_WSYNC(channel) do { } while (0) 59#else 60#define ZSDELAY() 61#define ZSDELAY_LONG() 62#define ZS_WSYNC(__channel) \ 63 readb(&((__channel)->control)) 64#endif 65 66#define ZS_CLOCK 4915200 /* Zilog input clock rate. */ 67#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */ 68 69/* 70 * We wrap our port structure around the generic uart_port. 71 */ 72struct uart_sunzilog_port { 73 struct uart_port port; 74 75 /* IRQ servicing chain. */ 76 struct uart_sunzilog_port *next; 77 78 /* Current values of Zilog write registers. */ 79 unsigned char curregs[NUM_ZSREGS]; 80 81 unsigned int flags; 82#define SUNZILOG_FLAG_CONS_KEYB 0x00000001 83#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002 84#define SUNZILOG_FLAG_IS_CONS 0x00000004 85#define SUNZILOG_FLAG_IS_KGDB 0x00000008 86#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010 87#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020 88#define SUNZILOG_FLAG_REGS_HELD 0x00000040 89#define SUNZILOG_FLAG_TX_STOPPED 0x00000080 90#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100 91#define SUNZILOG_FLAG_ESCC 0x00000200 92#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400 93 94 unsigned int cflag; 95 96 unsigned char parity_mask; 97 unsigned char prev_status; 98 99#ifdef CONFIG_SERIO 100 struct serio serio; 101 int serio_open; 102#endif 103}; 104 105static void sunzilog_putchar(struct uart_port *port, int ch); 106 107#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase)) 108#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT)) 109 110#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB) 111#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE) 112#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS) 113#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB) 114#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS) 115#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A) 116#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD) 117#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED) 118#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE) 119 120/* Reading and writing Zilog8530 registers. The delays are to make this 121 * driver work on the Sun4 which needs a settling delay after each chip 122 * register access, other machines handle this in hardware via auxiliary 123 * flip-flops which implement the settle time we do in software. 124 * 125 * The port lock must be held and local IRQs must be disabled 126 * when {read,write}_zsreg is invoked. 127 */ 128static unsigned char read_zsreg(struct zilog_channel __iomem *channel, 129 unsigned char reg) 130{ 131 unsigned char retval; 132 133 writeb(reg, &channel->control); 134 ZSDELAY(); 135 retval = readb(&channel->control); 136 ZSDELAY(); 137 138 return retval; 139} 140 141static void write_zsreg(struct zilog_channel __iomem *channel, 142 unsigned char reg, unsigned char value) 143{ 144 writeb(reg, &channel->control); 145 ZSDELAY(); 146 writeb(value, &channel->control); 147 ZSDELAY(); 148} 149 150static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel) 151{ 152 int i; 153 154 for (i = 0; i < 32; i++) { 155 unsigned char regval; 156 157 regval = readb(&channel->control); 158 ZSDELAY(); 159 if (regval & Rx_CH_AV) 160 break; 161 162 regval = read_zsreg(channel, R1); 163 readb(&channel->data); 164 ZSDELAY(); 165 166 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) { 167 writeb(ERR_RES, &channel->control); 168 ZSDELAY(); 169 ZS_WSYNC(channel); 170 } 171 } 172} 173 174/* This function must only be called when the TX is not busy. The UART 175 * port lock must be held and local interrupts disabled. 176 */ 177static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs) 178{ 179 int i; 180 int escc; 181 unsigned char r15; 182 183 /* Let pending transmits finish. */ 184 for (i = 0; i < 1000; i++) { 185 unsigned char stat = read_zsreg(channel, R1); 186 if (stat & ALL_SNT) 187 break; 188 udelay(100); 189 } 190 191 writeb(ERR_RES, &channel->control); 192 ZSDELAY(); 193 ZS_WSYNC(channel); 194 195 sunzilog_clear_fifo(channel); 196 197 /* Disable all interrupts. */ 198 write_zsreg(channel, R1, 199 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); 200 201 /* Set parity, sync config, stop bits, and clock divisor. */ 202 write_zsreg(channel, R4, regs[R4]); 203 204 /* Set misc. TX/RX control bits. */ 205 write_zsreg(channel, R10, regs[R10]); 206 207 /* Set TX/RX controls sans the enable bits. */ 208 write_zsreg(channel, R3, regs[R3] & ~RxENAB); 209 write_zsreg(channel, R5, regs[R5] & ~TxENAB); 210 211 /* Synchronous mode config. */ 212 write_zsreg(channel, R6, regs[R6]); 213 write_zsreg(channel, R7, regs[R7]); 214 215 /* Don't mess with the interrupt vector (R2, unused by us) and 216 * master interrupt control (R9). We make sure this is setup 217 * properly at probe time then never touch it again. 218 */ 219 220 /* Disable baud generator. */ 221 write_zsreg(channel, R14, regs[R14] & ~BRENAB); 222 223 /* Clock mode control. */ 224 write_zsreg(channel, R11, regs[R11]); 225 226 /* Lower and upper byte of baud rate generator divisor. */ 227 write_zsreg(channel, R12, regs[R12]); 228 write_zsreg(channel, R13, regs[R13]); 229 230 /* Now rewrite R14, with BRENAB (if set). */ 231 write_zsreg(channel, R14, regs[R14]); 232 233 /* External status interrupt control. */ 234 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN); 235 236 /* ESCC Extension Register */ 237 r15 = read_zsreg(channel, R15); 238 if (r15 & 0x01) { 239 write_zsreg(channel, R7, regs[R7p]); 240 241 /* External status interrupt and FIFO control. */ 242 write_zsreg(channel, R15, regs[R15] & ~WR7pEN); 243 escc = 1; 244 } else { 245 /* Clear FIFO bit case it is an issue */ 246 regs[R15] &= ~FIFOEN; 247 escc = 0; 248 } 249 250 /* Reset external status interrupts. */ 251 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */ 252 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */ 253 254 /* Rewrite R3/R5, this time without enables masked. */ 255 write_zsreg(channel, R3, regs[R3]); 256 write_zsreg(channel, R5, regs[R5]); 257 258 /* Rewrite R1, this time without IRQ enabled masked. */ 259 write_zsreg(channel, R1, regs[R1]); 260 261 return escc; 262} 263 264/* Reprogram the Zilog channel HW registers with the copies found in the 265 * software state struct. If the transmitter is busy, we defer this update 266 * until the next TX complete interrupt. Else, we do it right now. 267 * 268 * The UART port lock must be held and local interrupts disabled. 269 */ 270static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up, 271 struct zilog_channel __iomem *channel) 272{ 273 if (!ZS_REGS_HELD(up)) { 274 if (ZS_TX_ACTIVE(up)) { 275 up->flags |= SUNZILOG_FLAG_REGS_HELD; 276 } else { 277 __load_zsregs(channel, up->curregs); 278 } 279 } 280} 281 282static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up) 283{ 284 unsigned int cur_cflag = up->cflag; 285 int brg, new_baud; 286 287 up->cflag &= ~CBAUD; 288 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); 289 290 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 291 up->curregs[R12] = (brg & 0xff); 292 up->curregs[R13] = (brg >> 8) & 0xff; 293 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port)); 294} 295 296static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up, 297 unsigned char ch, int is_break) 298{ 299 if (ZS_IS_KEYB(up)) { 300 /* Stop-A is handled by drivers/char/keyboard.c now. */ 301#ifdef CONFIG_SERIO 302 if (up->serio_open) 303 serio_interrupt(&up->serio, ch, 0); 304#endif 305 } else if (ZS_IS_MOUSE(up)) { 306 int ret = suncore_mouse_baud_detection(ch, is_break); 307 308 switch (ret) { 309 case 2: 310 sunzilog_change_mouse_baud(up); 311 /* fallthru */ 312 case 1: 313 break; 314 315 case 0: 316#ifdef CONFIG_SERIO 317 if (up->serio_open) 318 serio_interrupt(&up->serio, ch, 0); 319#endif 320 break; 321 }; 322 } 323} 324 325static struct tty_struct * 326sunzilog_receive_chars(struct uart_sunzilog_port *up, 327 struct zilog_channel __iomem *channel) 328{ 329 struct tty_struct *tty; 330 unsigned char ch, r1, flag; 331 332 tty = NULL; 333 if (up->port.state != NULL && /* Unopened serial console */ 334 up->port.state->port.tty != NULL) /* Keyboard || mouse */ 335 tty = up->port.state->port.tty; 336 337 for (;;) { 338 339 r1 = read_zsreg(channel, R1); 340 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 341 writeb(ERR_RES, &channel->control); 342 ZSDELAY(); 343 ZS_WSYNC(channel); 344 } 345 346 ch = readb(&channel->control); 347 ZSDELAY(); 348 349 /* This funny hack depends upon BRK_ABRT not interfering 350 * with the other bits we care about in R1. 351 */ 352 if (ch & BRK_ABRT) 353 r1 |= BRK_ABRT; 354 355 if (!(ch & Rx_CH_AV)) 356 break; 357 358 ch = readb(&channel->data); 359 ZSDELAY(); 360 361 ch &= up->parity_mask; 362 363 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) { 364 sunzilog_kbdms_receive_chars(up, ch, 0); 365 continue; 366 } 367 368 if (tty == NULL) { 369 uart_handle_sysrq_char(&up->port, ch); 370 continue; 371 } 372 373 /* A real serial line, record the character and status. */ 374 flag = TTY_NORMAL; 375 up->port.icount.rx++; 376 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) { 377 if (r1 & BRK_ABRT) { 378 r1 &= ~(PAR_ERR | CRC_ERR); 379 up->port.icount.brk++; 380 if (uart_handle_break(&up->port)) 381 continue; 382 } 383 else if (r1 & PAR_ERR) 384 up->port.icount.parity++; 385 else if (r1 & CRC_ERR) 386 up->port.icount.frame++; 387 if (r1 & Rx_OVR) 388 up->port.icount.overrun++; 389 r1 &= up->port.read_status_mask; 390 if (r1 & BRK_ABRT) 391 flag = TTY_BREAK; 392 else if (r1 & PAR_ERR) 393 flag = TTY_PARITY; 394 else if (r1 & CRC_ERR) 395 flag = TTY_FRAME; 396 } 397 if (uart_handle_sysrq_char(&up->port, ch)) 398 continue; 399 400 if (up->port.ignore_status_mask == 0xff || 401 (r1 & up->port.ignore_status_mask) == 0) { 402 tty_insert_flip_char(tty, ch, flag); 403 } 404 if (r1 & Rx_OVR) 405 tty_insert_flip_char(tty, 0, TTY_OVERRUN); 406 } 407 408 return tty; 409} 410 411static void sunzilog_status_handle(struct uart_sunzilog_port *up, 412 struct zilog_channel __iomem *channel) 413{ 414 unsigned char status; 415 416 status = readb(&channel->control); 417 ZSDELAY(); 418 419 writeb(RES_EXT_INT, &channel->control); 420 ZSDELAY(); 421 ZS_WSYNC(channel); 422 423 if (status & BRK_ABRT) { 424 if (ZS_IS_MOUSE(up)) 425 sunzilog_kbdms_receive_chars(up, 0, 1); 426 if (ZS_IS_CONS(up)) { 427 /* Wait for BREAK to deassert to avoid potentially 428 * confusing the PROM. 429 */ 430 while (1) { 431 status = readb(&channel->control); 432 ZSDELAY(); 433 if (!(status & BRK_ABRT)) 434 break; 435 } 436 sun_do_break(); 437 return; 438 } 439 } 440 441 if (ZS_WANTS_MODEM_STATUS(up)) { 442 if (status & SYNC) 443 up->port.icount.dsr++; 444 445 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. 446 * But it does not tell us which bit has changed, we have to keep 447 * track of this ourselves. 448 */ 449 if ((status ^ up->prev_status) ^ DCD) 450 uart_handle_dcd_change(&up->port, 451 (status & DCD)); 452 if ((status ^ up->prev_status) ^ CTS) 453 uart_handle_cts_change(&up->port, 454 (status & CTS)); 455 456 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 457 } 458 459 up->prev_status = status; 460} 461 462static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, 463 struct zilog_channel __iomem *channel) 464{ 465 struct circ_buf *xmit; 466 467 if (ZS_IS_CONS(up)) { 468 unsigned char status = readb(&channel->control); 469 ZSDELAY(); 470 471 /* TX still busy? Just wait for the next TX done interrupt. 472 * 473 * It can occur because of how we do serial console writes. It would 474 * be nice to transmit console writes just like we normally would for 475 * a TTY line. (ie. buffered and TX interrupt driven). That is not 476 * easy because console writes cannot sleep. One solution might be 477 * to poll on enough port->xmit space becomming free. -DaveM 478 */ 479 if (!(status & Tx_BUF_EMP)) 480 return; 481 } 482 483 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE; 484 485 if (ZS_REGS_HELD(up)) { 486 __load_zsregs(channel, up->curregs); 487 up->flags &= ~SUNZILOG_FLAG_REGS_HELD; 488 } 489 490 if (ZS_TX_STOPPED(up)) { 491 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 492 goto ack_tx_int; 493 } 494 495 if (up->port.x_char) { 496 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 497 writeb(up->port.x_char, &channel->data); 498 ZSDELAY(); 499 ZS_WSYNC(channel); 500 501 up->port.icount.tx++; 502 up->port.x_char = 0; 503 return; 504 } 505 506 if (up->port.state == NULL) 507 goto ack_tx_int; 508 xmit = &up->port.state->xmit; 509 if (uart_circ_empty(xmit)) 510 goto ack_tx_int; 511 512 if (uart_tx_stopped(&up->port)) 513 goto ack_tx_int; 514 515 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 516 writeb(xmit->buf[xmit->tail], &channel->data); 517 ZSDELAY(); 518 ZS_WSYNC(channel); 519 520 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 521 up->port.icount.tx++; 522 523 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 524 uart_write_wakeup(&up->port); 525 526 return; 527 528ack_tx_int: 529 writeb(RES_Tx_P, &channel->control); 530 ZSDELAY(); 531 ZS_WSYNC(channel); 532} 533 534static irqreturn_t sunzilog_interrupt(int irq, void *dev_id) 535{ 536 struct uart_sunzilog_port *up = dev_id; 537 538 while (up) { 539 struct zilog_channel __iomem *channel 540 = ZILOG_CHANNEL_FROM_PORT(&up->port); 541 struct tty_struct *tty; 542 unsigned char r3; 543 544 spin_lock(&up->port.lock); 545 r3 = read_zsreg(channel, R3); 546 547 /* Channel A */ 548 tty = NULL; 549 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { 550 writeb(RES_H_IUS, &channel->control); 551 ZSDELAY(); 552 ZS_WSYNC(channel); 553 554 if (r3 & CHARxIP) 555 tty = sunzilog_receive_chars(up, channel); 556 if (r3 & CHAEXT) 557 sunzilog_status_handle(up, channel); 558 if (r3 & CHATxIP) 559 sunzilog_transmit_chars(up, channel); 560 } 561 spin_unlock(&up->port.lock); 562 563 if (tty) 564 tty_flip_buffer_push(tty); 565 566 /* Channel B */ 567 up = up->next; 568 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 569 570 spin_lock(&up->port.lock); 571 tty = NULL; 572 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { 573 writeb(RES_H_IUS, &channel->control); 574 ZSDELAY(); 575 ZS_WSYNC(channel); 576 577 if (r3 & CHBRxIP) 578 tty = sunzilog_receive_chars(up, channel); 579 if (r3 & CHBEXT) 580 sunzilog_status_handle(up, channel); 581 if (r3 & CHBTxIP) 582 sunzilog_transmit_chars(up, channel); 583 } 584 spin_unlock(&up->port.lock); 585 586 if (tty) 587 tty_flip_buffer_push(tty); 588 589 up = up->next; 590 } 591 592 return IRQ_HANDLED; 593} 594 595/* A convenient way to quickly get R0 status. The caller must _not_ hold the 596 * port lock, it is acquired here. 597 */ 598static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port) 599{ 600 struct zilog_channel __iomem *channel; 601 unsigned char status; 602 603 channel = ZILOG_CHANNEL_FROM_PORT(port); 604 status = readb(&channel->control); 605 ZSDELAY(); 606 607 return status; 608} 609 610/* The port lock is not held. */ 611static unsigned int sunzilog_tx_empty(struct uart_port *port) 612{ 613 unsigned long flags; 614 unsigned char status; 615 unsigned int ret; 616 617 spin_lock_irqsave(&port->lock, flags); 618 619 status = sunzilog_read_channel_status(port); 620 621 spin_unlock_irqrestore(&port->lock, flags); 622 623 if (status & Tx_BUF_EMP) 624 ret = TIOCSER_TEMT; 625 else 626 ret = 0; 627 628 return ret; 629} 630 631/* The port lock is held and interrupts are disabled. */ 632static unsigned int sunzilog_get_mctrl(struct uart_port *port) 633{ 634 unsigned char status; 635 unsigned int ret; 636 637 status = sunzilog_read_channel_status(port); 638 639 ret = 0; 640 if (status & DCD) 641 ret |= TIOCM_CAR; 642 if (status & SYNC) 643 ret |= TIOCM_DSR; 644 if (status & CTS) 645 ret |= TIOCM_CTS; 646 647 return ret; 648} 649 650/* The port lock is held and interrupts are disabled. */ 651static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl) 652{ 653 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 654 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 655 unsigned char set_bits, clear_bits; 656 657 set_bits = clear_bits = 0; 658 659 if (mctrl & TIOCM_RTS) 660 set_bits |= RTS; 661 else 662 clear_bits |= RTS; 663 if (mctrl & TIOCM_DTR) 664 set_bits |= DTR; 665 else 666 clear_bits |= DTR; 667 668 /* NOTE: Not subject to 'transmitter active' rule. */ 669 up->curregs[R5] |= set_bits; 670 up->curregs[R5] &= ~clear_bits; 671 write_zsreg(channel, R5, up->curregs[R5]); 672} 673 674/* The port lock is held and interrupts are disabled. */ 675static void sunzilog_stop_tx(struct uart_port *port) 676{ 677 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 678 679 up->flags |= SUNZILOG_FLAG_TX_STOPPED; 680} 681 682/* The port lock is held and interrupts are disabled. */ 683static void sunzilog_start_tx(struct uart_port *port) 684{ 685 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 686 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 687 unsigned char status; 688 689 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 690 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 691 692 status = readb(&channel->control); 693 ZSDELAY(); 694 695 /* TX busy? Just wait for the TX done interrupt. */ 696 if (!(status & Tx_BUF_EMP)) 697 return; 698 699 /* Send the first character to jump-start the TX done 700 * IRQ sending engine. 701 */ 702 if (port->x_char) { 703 writeb(port->x_char, &channel->data); 704 ZSDELAY(); 705 ZS_WSYNC(channel); 706 707 port->icount.tx++; 708 port->x_char = 0; 709 } else { 710 struct circ_buf *xmit = &port->state->xmit; 711 712 writeb(xmit->buf[xmit->tail], &channel->data); 713 ZSDELAY(); 714 ZS_WSYNC(channel); 715 716 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 717 port->icount.tx++; 718 719 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 720 uart_write_wakeup(&up->port); 721 } 722} 723 724/* The port lock is held. */ 725static void sunzilog_stop_rx(struct uart_port *port) 726{ 727 struct uart_sunzilog_port *up = UART_ZILOG(port); 728 struct zilog_channel __iomem *channel; 729 730 if (ZS_IS_CONS(up)) 731 return; 732 733 channel = ZILOG_CHANNEL_FROM_PORT(port); 734 735 /* Disable all RX interrupts. */ 736 up->curregs[R1] &= ~RxINT_MASK; 737 sunzilog_maybe_update_regs(up, channel); 738} 739 740/* The port lock is held. */ 741static void sunzilog_enable_ms(struct uart_port *port) 742{ 743 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 744 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 745 unsigned char new_reg; 746 747 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE); 748 if (new_reg != up->curregs[R15]) { 749 up->curregs[R15] = new_reg; 750 751 /* NOTE: Not subject to 'transmitter active' rule. */ 752 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN); 753 } 754} 755 756/* The port lock is not held. */ 757static void sunzilog_break_ctl(struct uart_port *port, int break_state) 758{ 759 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 760 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 761 unsigned char set_bits, clear_bits, new_reg; 762 unsigned long flags; 763 764 set_bits = clear_bits = 0; 765 766 if (break_state) 767 set_bits |= SND_BRK; 768 else 769 clear_bits |= SND_BRK; 770 771 spin_lock_irqsave(&port->lock, flags); 772 773 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits; 774 if (new_reg != up->curregs[R5]) { 775 up->curregs[R5] = new_reg; 776 777 /* NOTE: Not subject to 'transmitter active' rule. */ 778 write_zsreg(channel, R5, up->curregs[R5]); 779 } 780 781 spin_unlock_irqrestore(&port->lock, flags); 782} 783 784static void __sunzilog_startup(struct uart_sunzilog_port *up) 785{ 786 struct zilog_channel __iomem *channel; 787 788 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 789 up->prev_status = readb(&channel->control); 790 791 /* Enable receiver and transmitter. */ 792 up->curregs[R3] |= RxENAB; 793 up->curregs[R5] |= TxENAB; 794 795 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 796 sunzilog_maybe_update_regs(up, channel); 797} 798 799static int sunzilog_startup(struct uart_port *port) 800{ 801 struct uart_sunzilog_port *up = UART_ZILOG(port); 802 unsigned long flags; 803 804 if (ZS_IS_CONS(up)) 805 return 0; 806 807 spin_lock_irqsave(&port->lock, flags); 808 __sunzilog_startup(up); 809 spin_unlock_irqrestore(&port->lock, flags); 810 return 0; 811} 812 813/* 814 * The test for ZS_IS_CONS is explained by the following e-mail: 815 ***** 816 * From: Russell King <rmk@arm.linux.org.uk> 817 * Date: Sun, 8 Dec 2002 10:18:38 +0000 818 * 819 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote: 820 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument, 821 * > and I noticed that something is not right with reference 822 * > counting in this case. It seems that when the console 823 * > is open by kernel initially, this is not accounted 824 * > as an open, and uart_startup is not called. 825 * 826 * That is correct. We are unable to call uart_startup when the serial 827 * console is initialised because it may need to allocate memory (as 828 * request_irq does) and the memory allocators may not have been 829 * initialised. 830 * 831 * 1. initialise the port into a state where it can send characters in the 832 * console write method. 833 * 834 * 2. don't do the actual hardware shutdown in your shutdown() method (but 835 * do the normal software shutdown - ie, free irqs etc) 836 ***** 837 */ 838static void sunzilog_shutdown(struct uart_port *port) 839{ 840 struct uart_sunzilog_port *up = UART_ZILOG(port); 841 struct zilog_channel __iomem *channel; 842 unsigned long flags; 843 844 if (ZS_IS_CONS(up)) 845 return; 846 847 spin_lock_irqsave(&port->lock, flags); 848 849 channel = ZILOG_CHANNEL_FROM_PORT(port); 850 851 /* Disable receiver and transmitter. */ 852 up->curregs[R3] &= ~RxENAB; 853 up->curregs[R5] &= ~TxENAB; 854 855 /* Disable all interrupts and BRK assertion. */ 856 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); 857 up->curregs[R5] &= ~SND_BRK; 858 sunzilog_maybe_update_regs(up, channel); 859 860 spin_unlock_irqrestore(&port->lock, flags); 861} 862 863/* Shared by TTY driver and serial console setup. The port lock is held 864 * and local interrupts are disabled. 865 */ 866static void 867sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag, 868 unsigned int iflag, int brg) 869{ 870 871 up->curregs[R10] = NRZ; 872 up->curregs[R11] = TCBR | RCBR; 873 874 /* Program BAUD and clock source. */ 875 up->curregs[R4] &= ~XCLK_MASK; 876 up->curregs[R4] |= X16CLK; 877 up->curregs[R12] = brg & 0xff; 878 up->curregs[R13] = (brg >> 8) & 0xff; 879 up->curregs[R14] = BRSRC | BRENAB; 880 881 /* Character size, stop bits, and parity. */ 882 up->curregs[R3] &= ~RxN_MASK; 883 up->curregs[R5] &= ~TxN_MASK; 884 switch (cflag & CSIZE) { 885 case CS5: 886 up->curregs[R3] |= Rx5; 887 up->curregs[R5] |= Tx5; 888 up->parity_mask = 0x1f; 889 break; 890 case CS6: 891 up->curregs[R3] |= Rx6; 892 up->curregs[R5] |= Tx6; 893 up->parity_mask = 0x3f; 894 break; 895 case CS7: 896 up->curregs[R3] |= Rx7; 897 up->curregs[R5] |= Tx7; 898 up->parity_mask = 0x7f; 899 break; 900 case CS8: 901 default: 902 up->curregs[R3] |= Rx8; 903 up->curregs[R5] |= Tx8; 904 up->parity_mask = 0xff; 905 break; 906 }; 907 up->curregs[R4] &= ~0x0c; 908 if (cflag & CSTOPB) 909 up->curregs[R4] |= SB2; 910 else 911 up->curregs[R4] |= SB1; 912 if (cflag & PARENB) 913 up->curregs[R4] |= PAR_ENAB; 914 else 915 up->curregs[R4] &= ~PAR_ENAB; 916 if (!(cflag & PARODD)) 917 up->curregs[R4] |= PAR_EVEN; 918 else 919 up->curregs[R4] &= ~PAR_EVEN; 920 921 up->port.read_status_mask = Rx_OVR; 922 if (iflag & INPCK) 923 up->port.read_status_mask |= CRC_ERR | PAR_ERR; 924 if (iflag & (BRKINT | PARMRK)) 925 up->port.read_status_mask |= BRK_ABRT; 926 927 up->port.ignore_status_mask = 0; 928 if (iflag & IGNPAR) 929 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR; 930 if (iflag & IGNBRK) { 931 up->port.ignore_status_mask |= BRK_ABRT; 932 if (iflag & IGNPAR) 933 up->port.ignore_status_mask |= Rx_OVR; 934 } 935 936 if ((cflag & CREAD) == 0) 937 up->port.ignore_status_mask = 0xff; 938} 939 940/* The port lock is not held. */ 941static void 942sunzilog_set_termios(struct uart_port *port, struct ktermios *termios, 943 struct ktermios *old) 944{ 945 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 946 unsigned long flags; 947 int baud, brg; 948 949 baud = uart_get_baud_rate(port, termios, old, 1200, 76800); 950 951 spin_lock_irqsave(&up->port.lock, flags); 952 953 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 954 955 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg); 956 957 if (UART_ENABLE_MS(&up->port, termios->c_cflag)) 958 up->flags |= SUNZILOG_FLAG_MODEM_STATUS; 959 else 960 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS; 961 962 up->cflag = termios->c_cflag; 963 964 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port)); 965 966 uart_update_timeout(port, termios->c_cflag, baud); 967 968 spin_unlock_irqrestore(&up->port.lock, flags); 969} 970 971static const char *sunzilog_type(struct uart_port *port) 972{ 973 struct uart_sunzilog_port *up = UART_ZILOG(port); 974 975 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs"; 976} 977 978/* We do not request/release mappings of the registers here, this 979 * happens at early serial probe time. 980 */ 981static void sunzilog_release_port(struct uart_port *port) 982{ 983} 984 985static int sunzilog_request_port(struct uart_port *port) 986{ 987 return 0; 988} 989 990/* These do not need to do anything interesting either. */ 991static void sunzilog_config_port(struct uart_port *port, int flags) 992{ 993} 994 995/* We do not support letting the user mess with the divisor, IRQ, etc. */ 996static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser) 997{ 998 return -EINVAL; 999} 1000 1001#ifdef CONFIG_CONSOLE_POLL 1002static int sunzilog_get_poll_char(struct uart_port *port) 1003{ 1004 unsigned char ch, r1; 1005 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port; 1006 struct zilog_channel __iomem *channel 1007 = ZILOG_CHANNEL_FROM_PORT(&up->port); 1008 1009 1010 r1 = read_zsreg(channel, R1); 1011 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 1012 writeb(ERR_RES, &channel->control); 1013 ZSDELAY(); 1014 ZS_WSYNC(channel); 1015 } 1016 1017 ch = readb(&channel->control); 1018 ZSDELAY(); 1019 1020 /* This funny hack depends upon BRK_ABRT not interfering 1021 * with the other bits we care about in R1. 1022 */ 1023 if (ch & BRK_ABRT) 1024 r1 |= BRK_ABRT; 1025 1026 if (!(ch & Rx_CH_AV)) 1027 return NO_POLL_CHAR; 1028 1029 ch = readb(&channel->data); 1030 ZSDELAY(); 1031 1032 ch &= up->parity_mask; 1033 return ch; 1034} 1035 1036static void sunzilog_put_poll_char(struct uart_port *port, 1037 unsigned char ch) 1038{ 1039 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *)port; 1040 1041 sunzilog_putchar(&up->port, ch); 1042} 1043#endif /* CONFIG_CONSOLE_POLL */ 1044 1045static struct uart_ops sunzilog_pops = { 1046 .tx_empty = sunzilog_tx_empty, 1047 .set_mctrl = sunzilog_set_mctrl, 1048 .get_mctrl = sunzilog_get_mctrl, 1049 .stop_tx = sunzilog_stop_tx, 1050 .start_tx = sunzilog_start_tx, 1051 .stop_rx = sunzilog_stop_rx, 1052 .enable_ms = sunzilog_enable_ms, 1053 .break_ctl = sunzilog_break_ctl, 1054 .startup = sunzilog_startup, 1055 .shutdown = sunzilog_shutdown, 1056 .set_termios = sunzilog_set_termios, 1057 .type = sunzilog_type, 1058 .release_port = sunzilog_release_port, 1059 .request_port = sunzilog_request_port, 1060 .config_port = sunzilog_config_port, 1061 .verify_port = sunzilog_verify_port, 1062#ifdef CONFIG_CONSOLE_POLL 1063 .poll_get_char = sunzilog_get_poll_char, 1064 .poll_put_char = sunzilog_put_poll_char, 1065#endif 1066}; 1067 1068static int uart_chip_count; 1069static struct uart_sunzilog_port *sunzilog_port_table; 1070static struct zilog_layout __iomem **sunzilog_chip_regs; 1071 1072static struct uart_sunzilog_port *sunzilog_irq_chain; 1073 1074static struct uart_driver sunzilog_reg = { 1075 .owner = THIS_MODULE, 1076 .driver_name = "sunzilog", 1077 .dev_name = "ttyS", 1078 .major = TTY_MAJOR, 1079}; 1080 1081static int __init sunzilog_alloc_tables(int num_sunzilog) 1082{ 1083 struct uart_sunzilog_port *up; 1084 unsigned long size; 1085 int num_channels = num_sunzilog * 2; 1086 int i; 1087 1088 size = num_channels * sizeof(struct uart_sunzilog_port); 1089 sunzilog_port_table = kzalloc(size, GFP_KERNEL); 1090 if (!sunzilog_port_table) 1091 return -ENOMEM; 1092 1093 for (i = 0; i < num_channels; i++) { 1094 up = &sunzilog_port_table[i]; 1095 1096 spin_lock_init(&up->port.lock); 1097 1098 if (i == 0) 1099 sunzilog_irq_chain = up; 1100 1101 if (i < num_channels - 1) 1102 up->next = up + 1; 1103 else 1104 up->next = NULL; 1105 } 1106 1107 size = num_sunzilog * sizeof(struct zilog_layout __iomem *); 1108 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL); 1109 if (!sunzilog_chip_regs) { 1110 kfree(sunzilog_port_table); 1111 sunzilog_irq_chain = NULL; 1112 return -ENOMEM; 1113 } 1114 1115 return 0; 1116} 1117 1118static void sunzilog_free_tables(void) 1119{ 1120 kfree(sunzilog_port_table); 1121 sunzilog_irq_chain = NULL; 1122 kfree(sunzilog_chip_regs); 1123} 1124 1125#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */ 1126 1127static void sunzilog_putchar(struct uart_port *port, int ch) 1128{ 1129 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 1130 int loops = ZS_PUT_CHAR_MAX_DELAY; 1131 1132 /* This is a timed polling loop so do not switch the explicit 1133 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM 1134 */ 1135 do { 1136 unsigned char val = readb(&channel->control); 1137 if (val & Tx_BUF_EMP) { 1138 ZSDELAY(); 1139 break; 1140 } 1141 udelay(5); 1142 } while (--loops); 1143 1144 writeb(ch, &channel->data); 1145 ZSDELAY(); 1146 ZS_WSYNC(channel); 1147} 1148 1149#ifdef CONFIG_SERIO 1150 1151static DEFINE_SPINLOCK(sunzilog_serio_lock); 1152 1153static int sunzilog_serio_write(struct serio *serio, unsigned char ch) 1154{ 1155 struct uart_sunzilog_port *up = serio->port_data; 1156 unsigned long flags; 1157 1158 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1159 1160 sunzilog_putchar(&up->port, ch); 1161 1162 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1163 1164 return 0; 1165} 1166 1167static int sunzilog_serio_open(struct serio *serio) 1168{ 1169 struct uart_sunzilog_port *up = serio->port_data; 1170 unsigned long flags; 1171 int ret; 1172 1173 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1174 if (!up->serio_open) { 1175 up->serio_open = 1; 1176 ret = 0; 1177 } else 1178 ret = -EBUSY; 1179 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1180 1181 return ret; 1182} 1183 1184static void sunzilog_serio_close(struct serio *serio) 1185{ 1186 struct uart_sunzilog_port *up = serio->port_data; 1187 unsigned long flags; 1188 1189 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1190 up->serio_open = 0; 1191 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1192} 1193 1194#endif /* CONFIG_SERIO */ 1195 1196#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE 1197static void 1198sunzilog_console_write(struct console *con, const char *s, unsigned int count) 1199{ 1200 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1201 unsigned long flags; 1202 int locked = 1; 1203 1204 local_irq_save(flags); 1205 if (up->port.sysrq) { 1206 locked = 0; 1207 } else if (oops_in_progress) { 1208 locked = spin_trylock(&up->port.lock); 1209 } else 1210 spin_lock(&up->port.lock); 1211 1212 uart_console_write(&up->port, s, count, sunzilog_putchar); 1213 udelay(2); 1214 1215 if (locked) 1216 spin_unlock(&up->port.lock); 1217 local_irq_restore(flags); 1218} 1219 1220static int __init sunzilog_console_setup(struct console *con, char *options) 1221{ 1222 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1223 unsigned long flags; 1224 int baud, brg; 1225 1226 if (up->port.type != PORT_SUNZILOG) 1227 return -1; 1228 1229 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n", 1230 (sunzilog_reg.minor - 64) + con->index, con->index); 1231 1232 /* Get firmware console settings. */ 1233 sunserial_console_termios(con, up->port.dev->of_node); 1234 1235 /* Firmware console speed is limited to 150-->38400 baud so 1236 * this hackish cflag thing is OK. 1237 */ 1238 switch (con->cflag & CBAUD) { 1239 case B150: baud = 150; break; 1240 case B300: baud = 300; break; 1241 case B600: baud = 600; break; 1242 case B1200: baud = 1200; break; 1243 case B2400: baud = 2400; break; 1244 case B4800: baud = 4800; break; 1245 default: case B9600: baud = 9600; break; 1246 case B19200: baud = 19200; break; 1247 case B38400: baud = 38400; break; 1248 }; 1249 1250 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1251 1252 spin_lock_irqsave(&up->port.lock, flags); 1253 1254 up->curregs[R15] |= BRKIE; 1255 sunzilog_convert_to_zs(up, con->cflag, 0, brg); 1256 1257 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1258 __sunzilog_startup(up); 1259 1260 spin_unlock_irqrestore(&up->port.lock, flags); 1261 1262 return 0; 1263} 1264 1265static struct console sunzilog_console_ops = { 1266 .name = "ttyS", 1267 .write = sunzilog_console_write, 1268 .device = uart_console_device, 1269 .setup = sunzilog_console_setup, 1270 .flags = CON_PRINTBUFFER, 1271 .index = -1, 1272 .data = &sunzilog_reg, 1273}; 1274 1275static inline struct console *SUNZILOG_CONSOLE(void) 1276{ 1277 return &sunzilog_console_ops; 1278} 1279 1280#else 1281#define SUNZILOG_CONSOLE() (NULL) 1282#endif 1283 1284static void __devinit sunzilog_init_kbdms(struct uart_sunzilog_port *up) 1285{ 1286 int baud, brg; 1287 1288 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1289 up->cflag = B1200 | CS8 | CLOCAL | CREAD; 1290 baud = 1200; 1291 } else { 1292 up->cflag = B4800 | CS8 | CLOCAL | CREAD; 1293 baud = 4800; 1294 } 1295 1296 up->curregs[R15] |= BRKIE; 1297 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1298 sunzilog_convert_to_zs(up, up->cflag, 0, brg); 1299 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1300 __sunzilog_startup(up); 1301} 1302 1303#ifdef CONFIG_SERIO 1304static void __devinit sunzilog_register_serio(struct uart_sunzilog_port *up) 1305{ 1306 struct serio *serio = &up->serio; 1307 1308 serio->port_data = up; 1309 1310 serio->id.type = SERIO_RS232; 1311 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1312 serio->id.proto = SERIO_SUNKBD; 1313 strlcpy(serio->name, "zskbd", sizeof(serio->name)); 1314 } else { 1315 serio->id.proto = SERIO_SUN; 1316 serio->id.extra = 1; 1317 strlcpy(serio->name, "zsms", sizeof(serio->name)); 1318 } 1319 strlcpy(serio->phys, 1320 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ? 1321 "zs/serio0" : "zs/serio1"), 1322 sizeof(serio->phys)); 1323 1324 serio->write = sunzilog_serio_write; 1325 serio->open = sunzilog_serio_open; 1326 serio->close = sunzilog_serio_close; 1327 serio->dev.parent = up->port.dev; 1328 1329 serio_register_port(serio); 1330} 1331#endif 1332 1333static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up) 1334{ 1335 struct zilog_channel __iomem *channel; 1336 unsigned long flags; 1337 int baud, brg; 1338 1339 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1340 1341 spin_lock_irqsave(&up->port.lock, flags); 1342 if (ZS_IS_CHANNEL_A(up)) { 1343 write_zsreg(channel, R9, FHWRES); 1344 ZSDELAY_LONG(); 1345 (void) read_zsreg(channel, R0); 1346 } 1347 1348 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1349 SUNZILOG_FLAG_CONS_MOUSE)) { 1350 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1351 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1352 up->curregs[R3] = RxENAB | Rx8; 1353 up->curregs[R5] = TxENAB | Tx8; 1354 up->curregs[R6] = 0x00; /* SDLC Address */ 1355 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1356 up->curregs[R9] = NV; 1357 up->curregs[R7p] = 0x00; 1358 sunzilog_init_kbdms(up); 1359 /* Only enable interrupts if an ISR handler available */ 1360 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1361 up->curregs[R9] |= MIE; 1362 write_zsreg(channel, R9, up->curregs[R9]); 1363 } else { 1364 /* Normal serial TTY. */ 1365 up->parity_mask = 0xff; 1366 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1367 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1368 up->curregs[R3] = RxENAB | Rx8; 1369 up->curregs[R5] = TxENAB | Tx8; 1370 up->curregs[R6] = 0x00; /* SDLC Address */ 1371 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1372 up->curregs[R9] = NV; 1373 up->curregs[R10] = NRZ; 1374 up->curregs[R11] = TCBR | RCBR; 1375 baud = 9600; 1376 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1377 up->curregs[R12] = (brg & 0xff); 1378 up->curregs[R13] = (brg >> 8) & 0xff; 1379 up->curregs[R14] = BRSRC | BRENAB; 1380 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */ 1381 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL; 1382 if (__load_zsregs(channel, up->curregs)) { 1383 up->flags |= SUNZILOG_FLAG_ESCC; 1384 } 1385 /* Only enable interrupts if an ISR handler available */ 1386 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1387 up->curregs[R9] |= MIE; 1388 write_zsreg(channel, R9, up->curregs[R9]); 1389 } 1390 1391 spin_unlock_irqrestore(&up->port.lock, flags); 1392 1393#ifdef CONFIG_SERIO 1394 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1395 SUNZILOG_FLAG_CONS_MOUSE)) 1396 sunzilog_register_serio(up); 1397#endif 1398} 1399 1400static int zilog_irq = -1; 1401 1402static int __devinit zs_probe(struct platform_device *op, const struct of_device_id *match) 1403{ 1404 static int kbm_inst, uart_inst; 1405 int inst; 1406 struct uart_sunzilog_port *up; 1407 struct zilog_layout __iomem *rp; 1408 int keyboard_mouse = 0; 1409 int err; 1410 1411 if (of_find_property(op->dev.of_node, "keyboard", NULL)) 1412 keyboard_mouse = 1; 1413 1414 /* uarts must come before keyboards/mice */ 1415 if (keyboard_mouse) 1416 inst = uart_chip_count + kbm_inst; 1417 else 1418 inst = uart_inst; 1419 1420 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0, 1421 sizeof(struct zilog_layout), 1422 "zs"); 1423 if (!sunzilog_chip_regs[inst]) 1424 return -ENOMEM; 1425 1426 rp = sunzilog_chip_regs[inst]; 1427 1428 if (zilog_irq == -1) 1429 zilog_irq = op->archdata.irqs[0]; 1430 1431 up = &sunzilog_port_table[inst * 2]; 1432 1433 /* Channel A */ 1434 up[0].port.mapbase = op->resource[0].start + 0x00; 1435 up[0].port.membase = (void __iomem *) &rp->channelA; 1436 up[0].port.iotype = UPIO_MEM; 1437 up[0].port.irq = op->archdata.irqs[0]; 1438 up[0].port.uartclk = ZS_CLOCK; 1439 up[0].port.fifosize = 1; 1440 up[0].port.ops = &sunzilog_pops; 1441 up[0].port.type = PORT_SUNZILOG; 1442 up[0].port.flags = 0; 1443 up[0].port.line = (inst * 2) + 0; 1444 up[0].port.dev = &op->dev; 1445 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A; 1446 if (keyboard_mouse) 1447 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB; 1448 sunzilog_init_hw(&up[0]); 1449 1450 /* Channel B */ 1451 up[1].port.mapbase = op->resource[0].start + 0x04; 1452 up[1].port.membase = (void __iomem *) &rp->channelB; 1453 up[1].port.iotype = UPIO_MEM; 1454 up[1].port.irq = op->archdata.irqs[0]; 1455 up[1].port.uartclk = ZS_CLOCK; 1456 up[1].port.fifosize = 1; 1457 up[1].port.ops = &sunzilog_pops; 1458 up[1].port.type = PORT_SUNZILOG; 1459 up[1].port.flags = 0; 1460 up[1].port.line = (inst * 2) + 1; 1461 up[1].port.dev = &op->dev; 1462 up[1].flags |= 0; 1463 if (keyboard_mouse) 1464 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE; 1465 sunzilog_init_hw(&up[1]); 1466 1467 if (!keyboard_mouse) { 1468 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1469 &sunzilog_reg, up[0].port.line, 1470 false)) 1471 up->flags |= SUNZILOG_FLAG_IS_CONS; 1472 err = uart_add_one_port(&sunzilog_reg, &up[0].port); 1473 if (err) { 1474 of_iounmap(&op->resource[0], 1475 rp, sizeof(struct zilog_layout)); 1476 return err; 1477 } 1478 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1479 &sunzilog_reg, up[1].port.line, 1480 false)) 1481 up->flags |= SUNZILOG_FLAG_IS_CONS; 1482 err = uart_add_one_port(&sunzilog_reg, &up[1].port); 1483 if (err) { 1484 uart_remove_one_port(&sunzilog_reg, &up[0].port); 1485 of_iounmap(&op->resource[0], 1486 rp, sizeof(struct zilog_layout)); 1487 return err; 1488 } 1489 uart_inst++; 1490 } else { 1491 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) " 1492 "is a %s\n", 1493 dev_name(&op->dev), 1494 (unsigned long long) up[0].port.mapbase, 1495 op->archdata.irqs[0], sunzilog_type(&up[0].port)); 1496 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) " 1497 "is a %s\n", 1498 dev_name(&op->dev), 1499 (unsigned long long) up[1].port.mapbase, 1500 op->archdata.irqs[0], sunzilog_type(&up[1].port)); 1501 kbm_inst++; 1502 } 1503 1504 dev_set_drvdata(&op->dev, &up[0]); 1505 1506 return 0; 1507} 1508 1509static void __devexit zs_remove_one(struct uart_sunzilog_port *up) 1510{ 1511 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) { 1512#ifdef CONFIG_SERIO 1513 serio_unregister_port(&up->serio); 1514#endif 1515 } else 1516 uart_remove_one_port(&sunzilog_reg, &up->port); 1517} 1518 1519static int __devexit zs_remove(struct platform_device *op) 1520{ 1521 struct uart_sunzilog_port *up = dev_get_drvdata(&op->dev); 1522 struct zilog_layout __iomem *regs; 1523 1524 zs_remove_one(&up[0]); 1525 zs_remove_one(&up[1]); 1526 1527 regs = sunzilog_chip_regs[up[0].port.line / 2]; 1528 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout)); 1529 1530 dev_set_drvdata(&op->dev, NULL); 1531 1532 return 0; 1533} 1534 1535static const struct of_device_id zs_match[] = { 1536 { 1537 .name = "zs", 1538 }, 1539 {}, 1540}; 1541MODULE_DEVICE_TABLE(of, zs_match); 1542 1543static struct of_platform_driver zs_driver = { 1544 .driver = { 1545 .name = "zs", 1546 .owner = THIS_MODULE, 1547 .of_match_table = zs_match, 1548 }, 1549 .probe = zs_probe, 1550 .remove = __devexit_p(zs_remove), 1551}; 1552 1553static int __init sunzilog_init(void) 1554{ 1555 struct device_node *dp; 1556 int err; 1557 int num_keybms = 0; 1558 int num_sunzilog = 0; 1559 1560 for_each_node_by_name(dp, "zs") { 1561 num_sunzilog++; 1562 if (of_find_property(dp, "keyboard", NULL)) 1563 num_keybms++; 1564 } 1565 1566 if (num_sunzilog) { 1567 err = sunzilog_alloc_tables(num_sunzilog); 1568 if (err) 1569 goto out; 1570 1571 uart_chip_count = num_sunzilog - num_keybms; 1572 1573 err = sunserial_register_minors(&sunzilog_reg, 1574 uart_chip_count * 2); 1575 if (err) 1576 goto out_free_tables; 1577 } 1578 1579 err = of_register_platform_driver(&zs_driver); 1580 if (err) 1581 goto out_unregister_uart; 1582 1583 if (zilog_irq != -1) { 1584 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1585 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED, 1586 "zs", sunzilog_irq_chain); 1587 if (err) 1588 goto out_unregister_driver; 1589 1590 /* Enable Interrupts */ 1591 while (up) { 1592 struct zilog_channel __iomem *channel; 1593 1594 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */ 1595 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1596 up->flags |= SUNZILOG_FLAG_ISR_HANDLER; 1597 up->curregs[R9] |= MIE; 1598 write_zsreg(channel, R9, up->curregs[R9]); 1599 up = up->next; 1600 } 1601 } 1602 1603out: 1604 return err; 1605 1606out_unregister_driver: 1607 of_unregister_platform_driver(&zs_driver); 1608 1609out_unregister_uart: 1610 if (num_sunzilog) { 1611 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog); 1612 sunzilog_reg.cons = NULL; 1613 } 1614 1615out_free_tables: 1616 sunzilog_free_tables(); 1617 goto out; 1618} 1619 1620static void __exit sunzilog_exit(void) 1621{ 1622 of_unregister_platform_driver(&zs_driver); 1623 1624 if (zilog_irq != -1) { 1625 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1626 1627 /* Disable Interrupts */ 1628 while (up) { 1629 struct zilog_channel __iomem *channel; 1630 1631 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */ 1632 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1633 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER; 1634 up->curregs[R9] &= ~MIE; 1635 write_zsreg(channel, R9, up->curregs[R9]); 1636 up = up->next; 1637 } 1638 1639 free_irq(zilog_irq, sunzilog_irq_chain); 1640 zilog_irq = -1; 1641 } 1642 1643 if (sunzilog_reg.nr) { 1644 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr); 1645 sunzilog_free_tables(); 1646 } 1647} 1648 1649module_init(sunzilog_init); 1650module_exit(sunzilog_exit); 1651 1652MODULE_AUTHOR("David S. Miller"); 1653MODULE_DESCRIPTION("Sun Zilog serial port driver"); 1654MODULE_VERSION("2.0"); 1655MODULE_LICENSE("GPL"); 1656