1/* 2 * QNAP TS-409 Board Setup 3 * 4 * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> 5 * 6 * Copyright (C) 2008 Sylver Bruneau <sylver.bruneau@gmail.com> 7 * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com> 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License 11 * as published by the Free Software Foundation; either version 12 * 2 of the License, or (at your option) any later version. 13 */ 14 15#include <linux/kernel.h> 16#include <linux/init.h> 17#include <linux/platform_device.h> 18#include <linux/pci.h> 19#include <linux/irq.h> 20#include <linux/mtd/physmap.h> 21#include <linux/mv643xx_eth.h> 22#include <linux/leds.h> 23#include <linux/gpio_keys.h> 24#include <linux/input.h> 25#include <linux/i2c.h> 26#include <linux/serial_reg.h> 27#include <asm/mach-types.h> 28#include <asm/gpio.h> 29#include <asm/mach/arch.h> 30#include <asm/mach/pci.h> 31#include <mach/orion5x.h> 32#include "common.h" 33#include "mpp.h" 34#include "tsx09-common.h" 35 36/***************************************************************************** 37 * QNAP TS-409 Info 38 ****************************************************************************/ 39 40/* 41 * QNAP TS-409 hardware : 42 * - Marvell 88F5281-D0 43 * - Marvell 88SX7042 SATA controller (PCIe) 44 * - Marvell 88E1118 Gigabit Ethernet PHY 45 * - RTC S35390A (@0x30) on I2C bus 46 * - 8MB NOR flash 47 * - 256MB of DDR-2 RAM 48 */ 49 50/* 51 * 8MB NOR flash Device bus boot chip select 52 */ 53 54#define QNAP_TS409_NOR_BOOT_BASE 0xff800000 55#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M 56 57/**************************************************************************** 58 * 8MiB NOR flash. The struct mtd_partition is not in the same order as the 59 * partitions on the device because we want to keep compatability with 60 * existing QNAP firmware. 61 * 62 * Layout as used by QNAP: 63 * [2] 0x00000000-0x00200000 : "Kernel" 64 * [3] 0x00200000-0x00600000 : "RootFS1" 65 * [4] 0x00600000-0x00700000 : "RootFS2" 66 * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) 67 * [5] 0x00760000-0x00780000 : "U-Boot Config" 68 * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) 69 ***************************************************************************/ 70static struct mtd_partition qnap_ts409_partitions[] = { 71 { 72 .name = "U-Boot", 73 .size = 0x00080000, 74 .offset = 0x00780000, 75 .mask_flags = MTD_WRITEABLE, 76 }, { 77 .name = "Kernel", 78 .size = 0x00200000, 79 .offset = 0, 80 }, { 81 .name = "RootFS1", 82 .size = 0x00400000, 83 .offset = 0x00200000, 84 }, { 85 .name = "RootFS2", 86 .size = 0x00100000, 87 .offset = 0x00600000, 88 }, { 89 .name = "U-Boot Config", 90 .size = 0x00020000, 91 .offset = 0x00760000, 92 }, { 93 .name = "NAS Config", 94 .size = 0x00060000, 95 .offset = 0x00700000, 96 .mask_flags = MTD_WRITEABLE, 97 }, 98}; 99 100static struct physmap_flash_data qnap_ts409_nor_flash_data = { 101 .width = 1, 102 .parts = qnap_ts409_partitions, 103 .nr_parts = ARRAY_SIZE(qnap_ts409_partitions) 104}; 105 106static struct resource qnap_ts409_nor_flash_resource = { 107 .flags = IORESOURCE_MEM, 108 .start = QNAP_TS409_NOR_BOOT_BASE, 109 .end = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1, 110}; 111 112static struct platform_device qnap_ts409_nor_flash = { 113 .name = "physmap-flash", 114 .id = 0, 115 .dev = { .platform_data = &qnap_ts409_nor_flash_data, }, 116 .num_resources = 1, 117 .resource = &qnap_ts409_nor_flash_resource, 118}; 119 120/***************************************************************************** 121 * PCI 122 ****************************************************************************/ 123 124static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) 125{ 126 int irq; 127 128 /* 129 * Check for devices with hard-wired IRQs. 130 */ 131 irq = orion5x_pci_map_irq(dev, slot, pin); 132 if (irq != -1) 133 return irq; 134 135 /* 136 * PCI isn't used on the TS-409 137 */ 138 return -1; 139} 140 141static struct hw_pci qnap_ts409_pci __initdata = { 142 .nr_controllers = 2, 143 .swizzle = pci_std_swizzle, 144 .setup = orion5x_pci_sys_setup, 145 .scan = orion5x_pci_sys_scan_bus, 146 .map_irq = qnap_ts409_pci_map_irq, 147}; 148 149static int __init qnap_ts409_pci_init(void) 150{ 151 if (machine_is_ts409()) 152 pci_common_init(&qnap_ts409_pci); 153 154 return 0; 155} 156 157subsys_initcall(qnap_ts409_pci_init); 158 159/***************************************************************************** 160 * RTC S35390A on I2C bus 161 ****************************************************************************/ 162 163#define TS409_RTC_GPIO 10 164 165static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { 166 I2C_BOARD_INFO("s35390a", 0x30), 167}; 168 169/***************************************************************************** 170 * LEDs attached to GPIO 171 ****************************************************************************/ 172 173static struct gpio_led ts409_led_pins[] = { 174 { 175 .name = "ts409:red:sata1", 176 .gpio = 4, 177 .active_low = 1, 178 }, { 179 .name = "ts409:red:sata2", 180 .gpio = 5, 181 .active_low = 1, 182 }, { 183 .name = "ts409:red:sata3", 184 .gpio = 6, 185 .active_low = 1, 186 }, { 187 .name = "ts409:red:sata4", 188 .gpio = 7, 189 .active_low = 1, 190 }, 191}; 192 193static struct gpio_led_platform_data ts409_led_data = { 194 .leds = ts409_led_pins, 195 .num_leds = ARRAY_SIZE(ts409_led_pins), 196}; 197 198static struct platform_device ts409_leds = { 199 .name = "leds-gpio", 200 .id = -1, 201 .dev = { 202 .platform_data = &ts409_led_data, 203 }, 204}; 205 206/**************************************************************************** 207 * GPIO Attached Keys 208 * Power button is attached to the PIC microcontroller 209 ****************************************************************************/ 210 211#define QNAP_TS409_GPIO_KEY_RESET 14 212#define QNAP_TS409_GPIO_KEY_MEDIA 15 213 214static struct gpio_keys_button qnap_ts409_buttons[] = { 215 { 216 .code = KEY_RESTART, 217 .gpio = QNAP_TS409_GPIO_KEY_RESET, 218 .desc = "Reset Button", 219 .active_low = 1, 220 }, { 221 .code = KEY_COPY, 222 .gpio = QNAP_TS409_GPIO_KEY_MEDIA, 223 .desc = "USB Copy Button", 224 .active_low = 1, 225 }, 226}; 227 228static struct gpio_keys_platform_data qnap_ts409_button_data = { 229 .buttons = qnap_ts409_buttons, 230 .nbuttons = ARRAY_SIZE(qnap_ts409_buttons), 231}; 232 233static struct platform_device qnap_ts409_button_device = { 234 .name = "gpio-keys", 235 .id = -1, 236 .num_resources = 0, 237 .dev = { 238 .platform_data = &qnap_ts409_button_data, 239 }, 240}; 241 242/***************************************************************************** 243 * General Setup 244 ****************************************************************************/ 245static struct orion5x_mpp_mode ts409_mpp_modes[] __initdata = { 246 { 0, MPP_UNUSED }, 247 { 1, MPP_UNUSED }, 248 { 2, MPP_UNUSED }, 249 { 3, MPP_UNUSED }, 250 { 4, MPP_GPIO }, /* HDD 1 status */ 251 { 5, MPP_GPIO }, /* HDD 2 status */ 252 { 6, MPP_GPIO }, /* HDD 3 status */ 253 { 7, MPP_GPIO }, /* HDD 4 status */ 254 { 8, MPP_UNUSED }, 255 { 9, MPP_UNUSED }, 256 { 10, MPP_GPIO }, /* RTC int */ 257 { 11, MPP_UNUSED }, 258 { 12, MPP_UNUSED }, 259 { 13, MPP_UNUSED }, 260 { 14, MPP_GPIO }, /* SW_RST */ 261 { 15, MPP_GPIO }, /* USB copy button */ 262 { 16, MPP_UART }, /* UART1 RXD */ 263 { 17, MPP_UART }, /* UART1 TXD */ 264 { 18, MPP_UNUSED }, 265 { 19, MPP_UNUSED }, 266 { -1 }, 267}; 268 269static void __init qnap_ts409_init(void) 270{ 271 /* 272 * Setup basic Orion functions. Need to be called early. 273 */ 274 orion5x_init(); 275 276 orion5x_mpp_conf(ts409_mpp_modes); 277 278 /* 279 * Configure peripherals. 280 */ 281 orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE, 282 QNAP_TS409_NOR_BOOT_SIZE); 283 platform_device_register(&qnap_ts409_nor_flash); 284 285 orion5x_ehci0_init(); 286 qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + 287 qnap_ts409_partitions[5].offset, 288 qnap_ts409_partitions[5].size); 289 orion5x_eth_init(&qnap_tsx09_eth_data); 290 orion5x_i2c_init(); 291 orion5x_uart0_init(); 292 orion5x_uart1_init(); 293 294 platform_device_register(&qnap_ts409_button_device); 295 296 /* Get RTC IRQ and register the chip */ 297 if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) { 298 if (gpio_direction_input(TS409_RTC_GPIO) == 0) 299 qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO); 300 else 301 gpio_free(TS409_RTC_GPIO); 302 } 303 if (qnap_ts409_i2c_rtc.irq == 0) 304 pr_warning("qnap_ts409_init: failed to get RTC IRQ\n"); 305 i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); 306 platform_device_register(&ts409_leds); 307 308 /* register tsx09 specific power-off method */ 309 pm_power_off = qnap_tsx09_power_off; 310} 311 312MACHINE_START(TS409, "QNAP TS-409") 313 /* Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com> */ 314 .phys_io = ORION5X_REGS_PHYS_BASE, 315 .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, 316 .boot_params = 0x00000100, 317 .init_machine = qnap_ts409_init, 318 .map_io = orion5x_map_io, 319 .init_irq = orion5x_init_irq, 320 .timer = &orion5x_timer, 321 .fixup = tag_fixup_mem32, 322MACHINE_END 323