1 2menu "Passive cards" 3 4config ISDN_DRV_HISAX 5 tristate "HiSax SiemensChipSet driver support" 6 select CRC_CCITT 7 ---help--- 8 This is a driver supporting the Siemens chipset on various 9 ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles 10 S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many 11 compatibles). 12 13 HiSax is just the name of this driver, not the name of any hardware. 14 15 If you have a card with such a chipset, you should say Y here and 16 also to the configuration option of the driver for your particular 17 card, below. 18 19if ISDN_DRV_HISAX!=n 20 21comment "D-channel protocol features" 22 23config HISAX_EURO 24 bool "HiSax Support for EURO/DSS1" 25 help 26 Say Y or N according to the D-channel protocol which your local 27 telephone service company provides. 28 29 The call control protocol E-DSS1 is used in most European countries. 30 If unsure, say Y. 31 32config DE_AOC 33 bool "Support for german chargeinfo" 34 depends on HISAX_EURO 35 help 36 If you want that the HiSax hardware driver sends messages to the 37 upper level of the isdn code on each AOCD (Advice Of Charge, During 38 the call -- transmission of the fee information during a call) and 39 on each AOCE (Advice Of Charge, at the End of the call -- 40 transmission of fee information at the end of the call), say Y here. 41 This works only in Germany. 42 43config HISAX_NO_SENDCOMPLETE 44 bool "Disable sending complete" 45 depends on HISAX_EURO 46 help 47 If you have trouble with some ugly exchanges or you live in 48 Australia select this option. 49 50config HISAX_NO_LLC 51 bool "Disable sending low layer compatibility" 52 depends on HISAX_EURO 53 help 54 If you have trouble with some ugly exchanges try to select this 55 option. 56 57config HISAX_NO_KEYPAD 58 bool "Disable keypad protocol option" 59 depends on HISAX_EURO 60 help 61 If you like to send special dial strings including * or # without 62 using the keypad protocol, select this option. 63 64config HISAX_1TR6 65 bool "HiSax Support for german 1TR6" 66 help 67 Say Y or N according to the D-channel protocol which your local 68 telephone service company provides. 69 70 1TR6 is an old call control protocol which was used in Germany 71 before E-DSS1 was established. Nowadays, all new lines in Germany 72 use E-DSS1. 73 74config HISAX_NI1 75 bool "HiSax Support for US NI1" 76 help 77 Enable this if you like to use ISDN in US on a NI1 basic rate 78 interface. 79 80config HISAX_MAX_CARDS 81 int "Maximum number of cards supported by HiSax" 82 default "8" 83 help 84 This option allows you to specify the maximum number of cards which 85 the HiSax driver will be able to handle. 86 87comment "HiSax supported cards" 88 89config HISAX_16_0 90 bool "Teles 16.0/8.0" 91 depends on ISA 92 help 93 This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8 94 and many compatibles. 95 96 See <file:Documentation/isdn/README.HiSax> on how to configure it 97 using the different cards, a different D-channel protocol, or 98 non-standard IRQ/port/shmem settings. 99 100config HISAX_16_3 101 bool "Teles 16.3 or PNP or PCMCIA" 102 help 103 This enables HiSax support for the Teles ISDN-cards S0-16.3 the 104 Teles/Creatix PnP and the Teles PCMCIA. 105 106 See <file:Documentation/isdn/README.HiSax> on how to configure it 107 using the different cards, a different D-channel protocol, or 108 non-standard IRQ/port settings. 109 110config HISAX_TELESPCI 111 bool "Teles PCI" 112 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) 113 help 114 This enables HiSax support for the Teles PCI. 115 See <file:Documentation/isdn/README.HiSax> on how to configure it. 116 117config HISAX_S0BOX 118 bool "Teles S0Box" 119 help 120 This enables HiSax support for the Teles/Creatix parallel port 121 S0BOX. See <file:Documentation/isdn/README.HiSax> on how to 122 configure it. 123 124config HISAX_AVM_A1 125 bool "AVM A1 (Fritz)" 126 depends on ISA 127 help 128 This enables HiSax support for the AVM A1 (aka "Fritz"). 129 130 See <file:Documentation/isdn/README.HiSax> on how to configure it 131 using the different cards, a different D-channel protocol, or 132 non-standard IRQ/port settings. 133 134config HISAX_FRITZPCI 135 bool "AVM PnP/PCI (Fritz!PnP/PCI)" 136 depends on BROKEN || !PPC64 137 help 138 This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI". 139 See <file:Documentation/isdn/README.HiSax> on how to configure it. 140 141config HISAX_AVM_A1_PCMCIA 142 bool "AVM A1 PCMCIA (Fritz)" 143 help 144 This enables HiSax support for the AVM A1 "Fritz!PCMCIA"). 145 See <file:Documentation/isdn/README.HiSax> on how to configure it. 146 147config HISAX_ELSA 148 bool "Elsa cards" 149 help 150 This enables HiSax support for the Elsa Mircolink ISA cards, for the 151 Elsa Quickstep series cards and Elsa PCMCIA. 152 153 See <file:Documentation/isdn/README.HiSax> on how to configure it 154 using the different cards, a different D-channel protocol, or 155 non-standard IRQ/port settings. 156 157config HISAX_IX1MICROR2 158 bool "ITK ix1-micro Revision 2" 159 depends on ISA 160 help 161 This enables HiSax support for the ITK ix1-micro Revision 2 card. 162 163 See <file:Documentation/isdn/README.HiSax> on how to configure it 164 using the different cards, a different D-channel protocol, or 165 non-standard IRQ/port settings. 166 167config HISAX_DIEHLDIVA 168 bool "Eicon.Diehl Diva cards" 169 help 170 This enables HiSax support for the Eicon.Diehl Diva none PRO 171 versions passive ISDN cards. 172 173 See <file:Documentation/isdn/README.HiSax> on how to configure it 174 using the different cards, a different D-channel protocol, or 175 non-standard IRQ/port settings. 176 177config HISAX_ASUSCOM 178 bool "ASUSCOM ISA cards" 179 depends on ISA 180 help 181 This enables HiSax support for the AsusCom and their OEM versions 182 passive ISDN ISA cards. 183 184 See <file:Documentation/isdn/README.HiSax> on how to configure it 185 using the different cards, a different D-channel protocol, or 186 non-standard IRQ/port settings. 187 188config HISAX_TELEINT 189 bool "TELEINT cards" 190 depends on ISA 191 help 192 This enables HiSax support for the TELEINT SA1 semiactiv ISDN card. 193 194 See <file:Documentation/isdn/README.HiSax> on how to configure it 195 using the different cards, a different D-channel protocol, or 196 non-standard IRQ/port settings. 197 198config HISAX_HFCS 199 bool "HFC-S based cards" 200 depends on ISA 201 help 202 This enables HiSax support for the HFC-S 2BDS0 based cards, like 203 teles 16.3c. 204 205 See <file:Documentation/isdn/README.HiSax> on how to configure it 206 using the different cards, a different D-channel protocol, or 207 non-standard IRQ/port settings. 208 209config HISAX_SEDLBAUER 210 bool "Sedlbauer cards" 211 help 212 This enables HiSax support for the Sedlbauer passive ISDN cards. 213 214 See <file:Documentation/isdn/README.HiSax> on how to configure it 215 using the different cards, a different D-channel protocol, or 216 non-standard IRQ/port settings. 217 218config HISAX_SPORTSTER 219 bool "USR Sportster internal TA" 220 depends on ISA 221 help 222 This enables HiSax support for the USR Sportster internal TA card. 223 224 See <file:Documentation/isdn/README.HiSax> on how to configure it 225 using a different D-channel protocol, or non-standard IRQ/port 226 settings. 227 228config HISAX_MIC 229 bool "MIC card" 230 depends on ISA 231 help 232 This enables HiSax support for the ITH MIC card. 233 234 See <file:Documentation/isdn/README.HiSax> on how to configure it 235 using a different D-channel protocol, or non-standard IRQ/port 236 settings. 237 238config HISAX_NETJET 239 bool "NETjet card" 240 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) 241 help 242 This enables HiSax support for the NetJet from Traverse 243 Technologies. 244 245 See <file:Documentation/isdn/README.HiSax> on how to configure it 246 using a different D-channel protocol, or non-standard IRQ/port 247 settings. 248 249config HISAX_NETJET_U 250 bool "NETspider U card" 251 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) 252 help 253 This enables HiSax support for the Netspider U interface ISDN card 254 from Traverse Technologies. 255 See <file:Documentation/isdn/README.HiSax> on how to configure it 256 using a different D-channel protocol, or non-standard IRQ/port 257 settings. 258 259config HISAX_NICCY 260 bool "Niccy PnP/PCI card" 261 help 262 This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI. 263 264 See <file:Documentation/isdn/README.HiSax> on how to configure it 265 using a different D-channel protocol, or non-standard IRQ/port 266 settings. 267 268config HISAX_ISURF 269 bool "Siemens I-Surf card" 270 depends on ISA 271 help 272 This enables HiSax support for the Siemens I-Talk/I-Surf card with 273 ISAR chip. 274 See <file:Documentation/isdn/README.HiSax> on how to configure it 275 using a different D-channel protocol, or non-standard IRQ/port 276 settings. 277 278config HISAX_HSTSAPHIR 279 bool "HST Saphir card" 280 depends on ISA 281 help 282 This enables HiSax support for the HST Saphir card. 283 284 See <file:Documentation/isdn/README.HiSax> on how to configure it 285 using a different D-channel protocol, or non-standard IRQ/port 286 settings. 287 288config HISAX_BKM_A4T 289 bool "Telekom A4T card" 290 depends on PCI 291 help 292 This enables HiSax support for the Telekom A4T card. 293 294 See <file:Documentation/isdn/README.HiSax> on how to configure it 295 using a different D-channel protocol, or non-standard IRQ/port 296 settings. 297 298config HISAX_SCT_QUADRO 299 bool "Scitel Quadro card" 300 depends on PCI 301 help 302 This enables HiSax support for the Scitel Quadro card. 303 304 See <file:Documentation/isdn/README.HiSax> on how to configure it 305 using a different D-channel protocol, or non-standard IRQ/port 306 settings. 307 308config HISAX_GAZEL 309 bool "Gazel cards" 310 help 311 This enables HiSax support for the Gazel cards. 312 313 See <file:Documentation/isdn/README.HiSax> on how to configure it 314 using a different D-channel protocol, or non-standard IRQ/port 315 settings. 316 317config HISAX_HFC_PCI 318 bool "HFC PCI-Bus cards" 319 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) 320 help 321 This enables HiSax support for the HFC-S PCI 2BDS0 based cards. 322 323 For more information see under 324 <file:Documentation/isdn/README.hfc-pci>. 325 326config HISAX_W6692 327 bool "Winbond W6692 based cards" 328 depends on PCI 329 help 330 This enables HiSax support for Winbond W6692 based PCI ISDN cards. 331 332 See <file:Documentation/isdn/README.HiSax> on how to configure it 333 using a different D-channel protocol, or non-standard IRQ/port 334 settings. 335 336config HISAX_HFC_SX 337 bool "HFC-S+, HFC-SP, HFC-PCMCIA cards" 338 help 339 This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA 340 cards. This code is not finished yet. 341 342config HISAX_ENTERNOW_PCI 343 bool "Formula-n enter:now PCI card" 344 depends on HISAX_NETJET && PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV)) 345 help 346 This enables HiSax support for the Formula-n enter:now PCI 347 ISDN card. 348 349endif 350 351if ISDN_DRV_HISAX 352 353config HISAX_DEBUG 354 bool "HiSax debugging" 355 help 356 This enables debugging code in the new-style HiSax drivers, i.e. 357 the ST5481 USB driver currently. 358 If in doubt, say yes. 359 360comment "HiSax PCMCIA card service modules" 361 362config HISAX_SEDLBAUER_CS 363 tristate "Sedlbauer PCMCIA cards" 364 depends on PCMCIA && HISAX_SEDLBAUER 365 help 366 This enables the PCMCIA client driver for the Sedlbauer Speed Star 367 and Speed Star II cards. 368 369config HISAX_ELSA_CS 370 tristate "ELSA PCMCIA MicroLink cards" 371 depends on PCMCIA && HISAX_ELSA 372 help 373 This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink 374 card. 375 376config HISAX_AVM_A1_CS 377 tristate "AVM A1 PCMCIA cards" 378 depends on PCMCIA && ISDN_DRV_HISAX 379 help 380 This enables the PCMCIA client driver for the AVM A1 / Fritz!Card 381 PCMCIA cards. 382 383config HISAX_TELES_CS 384 tristate "TELES PCMCIA cards" 385 depends on PCMCIA && HISAX_16_3 386 help 387 This enables the PCMCIA client driver for the Teles PCMCIA cards. 388 389comment "HiSax sub driver modules" 390 391config HISAX_ST5481 392 tristate "ST5481 USB ISDN modem (EXPERIMENTAL)" 393 depends on USB && EXPERIMENTAL 394 select ISDN_HDLC 395 select CRC_CCITT 396 select BITREVERSE 397 help 398 This enables the driver for ST5481 based USB ISDN adapters, 399 e.g. the BeWan Gazel 128 USB 400 401config HISAX_HFCUSB 402 tristate "HFC USB based ISDN modems (EXPERIMENTAL)" 403 depends on USB && EXPERIMENTAL 404 help 405 This enables the driver for HFC USB based ISDN modems. 406 407config HISAX_HFC4S8S 408 tristate "HFC-4S/8S based ISDN cards (EXPERIMENTAL)" 409 depends on EXPERIMENTAL 410 help 411 This enables the driver for HFC-4S/8S based ISDN cards. 412 413config HISAX_FRITZ_PCIPNP 414 tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)" 415 depends on PCI && EXPERIMENTAL 416 help 417 This enables the driver for the AVM Fritz!Card PCI, 418 Fritz!Card PCI v2 and Fritz!Card PnP. 419 (the latter also needs you to select "ISA Plug and Play support" 420 from the menu "Plug and Play configuration") 421 422config HISAX_AVM_A1_PCMCIA 423 bool 424 depends on HISAX_AVM_A1_CS 425 default y 426 427endif 428 429endmenu 430 431