1/* 2 * linux/include/asm-arm/arch-l7200/serial_l7200.h 3 * 4 * Copyright (c) 2000 Steven Hill (sjhill@cotw.com) 5 * 6 * Changelog: 7 * 05-09-2000 SJH Created 8 */ 9#ifndef __ASM_ARCH_SERIAL_L7200_H 10#define __ASM_ARCH_SERIAL_L7200_H 11 12#include <asm/arch/memory.h> 13 14/* 15 * This assumes you have a 3.6864 MHz clock for your UART. 16 */ 17#define BASE_BAUD 3686400 18 19/* 20 * UART base register addresses 21 */ 22#define UART1_BASE (IO_BASE + 0x00044000) 23#define UART2_BASE (IO_BASE + 0x00045000) 24 25/* 26 * UART register offsets 27 */ 28#define UARTDR 0x00 /* Tx/Rx data */ 29#define RXSTAT 0x04 /* Rx status */ 30#define H_UBRLCR 0x08 /* mode register high */ 31#define M_UBRLCR 0x0C /* mode reg mid (MSB of buad)*/ 32#define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/ 33#define UARTCON 0x14 /* control register */ 34#define UARTFLG 0x18 /* flag register */ 35#define UARTINTSTAT 0x1C /* FIFO IRQ status register */ 36#define UARTINTMASK 0x20 /* FIFO IRQ mask register */ 37 38/* 39 * UART baud rate register values 40 */ 41#define BR_110 0x827 42#define BR_1200 0x06e 43#define BR_2400 0x05f 44#define BR_4800 0x02f 45#define BR_9600 0x017 46#define BR_14400 0x00f 47#define BR_19200 0x00b 48#define BR_38400 0x005 49#define BR_57600 0x003 50#define BR_76800 0x002 51#define BR_115200 0x001 52 53/* 54 * Receiver status register (RXSTAT) mask values 55 */ 56#define RXSTAT_NO_ERR 0x00 /* No error */ 57#define RXSTAT_FRM_ERR 0x01 /* Framing error */ 58#define RXSTAT_PAR_ERR 0x02 /* Parity error */ 59#define RXSTAT_OVR_ERR 0x04 /* Overrun error */ 60 61/* 62 * High byte of UART bit rate and line control register (H_UBRLCR) values 63 */ 64#define UBRLCR_BRK 0x01 /* generate break on tx */ 65#define UBRLCR_PEN 0x02 /* enable parity */ 66#define UBRLCR_PDIS 0x00 /* disable parity */ 67#define UBRLCR_EVEN 0x04 /* 1= even parity,0 = odd parity */ 68#define UBRLCR_STP2 0x08 /* transmit 2 stop bits */ 69#define UBRLCR_FIFO 0x10 /* enable FIFO */ 70#define UBRLCR_LEN5 0x60 /* word length5 */ 71#define UBRLCR_LEN6 0x40 /* word length6 */ 72#define UBRLCR_LEN7 0x20 /* word length7 */ 73#define UBRLCR_LEN8 0x00 /* word length8 */ 74 75/* 76 * UART control register (UARTCON) values 77 */ 78#define UARTCON_UARTEN 0x01 /* Enable UART */ 79#define UARTCON_DMAONERR 0x08 /* Mask RxDmaRq when errors occur */ 80 81/* 82 * UART flag register (UARTFLG) mask values 83 */ 84#define UARTFLG_UTXFF 0x20 /* Transmit FIFO full */ 85#define UARTFLG_URXFE 0x10 /* Receiver FIFO empty */ 86#define UARTFLG_UBUSY 0x08 /* Transmitter busy */ 87#define UARTFLG_DCD 0x04 /* Data carrier detect */ 88#define UARTFLG_DSR 0x02 /* Data set ready */ 89#define UARTFLG_CTS 0x01 /* Clear to send */ 90 91/* 92 * UART interrupt status/clear registers (UARTINTSTAT/CLR) values 93 */ 94#define UART_TXINT 0x01 /* TX interrupt */ 95#define UART_RXINT 0x02 /* RX interrupt */ 96#define UART_RXERRINT 0x04 /* RX error interrupt */ 97#define UART_MSINT 0x08 /* Modem Status interrupt */ 98#define UART_UDINT 0x10 /* UART Disabled interrupt */ 99#define UART_ALLIRQS 0x1f /* All interrupts */ 100 101#endif 102