| /linux-master/drivers/net/ethernet/ti/ |
| H A D | netcp_sgmii.c | 133 pr_err("serdes PLL not locked\n");
|
| H A D | netcp_xgbepcsr.c | 226 pr_err("XGBE serdes not locked: time out.\n");
371 pr_err("XGBE: unknown current_state[%d] %d\n",
|
| /linux-master/drivers/net/wireless/ath/ |
| H A D | main.c | 55 pr_err("skbuff alloc of size %u failed\n", len);
|
| /linux-master/drivers/net/wireless/broadcom/brcm80211/brcmfmac/ |
| H A D | tracepoint.c | 27 pr_err("%s: %pV", func, &vaf);
|
| /linux-master/drivers/net/wireless/quantenna/qtnfmac/ |
| H A D | shm_ipc.c | 30 pr_err("wrong rx packet size: %zu\n", size);
155 pr_err("TX ACK timeout\n");
|
| H A D | trans.c | 57 pr_err("response timeout\n");
90 pr_err("unexpected response\n");
95 pr_err("seq num mismatch\n");
161 pr_err("invalid bus pointer\n");
|
| /linux-master/drivers/net/wireless/st/cw1200/ |
| H A D | hwio.c | 38 pr_err("buffer is not aligned.\n");
136 pr_err("error :[%d]\n", ret);
163 pr_err("error :[%d]\n", ret);
178 pr_err("Can't read more than 0xfff words.\n");
186 pr_err("Can't write address register.\n");
193 pr_err("Can't read config register.\n");
201 pr_err("Can't write prefetch bit.\n");
209 pr_err("Can't check prefetch bit.\n");
219 pr_err("Prefetch bit is not cleared.\n");
226 pr_err("Ca
[all...] |
| /linux-master/drivers/net/wireless/ti/wlcore/ |
| H A D | debug.h | 51 pr_err(DRIVER_PREFIX "ERROR " fmt "\n", ##arg)
|
| /linux-master/drivers/of/ |
| H A D | fdt_address.c | 177 pr_err("warning: device tree node '%s' has no address.\n",
191 pr_err("Bad cell count for %s\n",
218 pr_err("Bad cell count for %s\n",
|
| H A D | pdt.c | 59 pr_err("%s: pkg2path failed; assigning %s\n", __func__, buf);
|
| /linux-master/drivers/pinctrl/samsung/ |
| H A D | pinctrl-exynos-arm.c | 68 pr_err("%s: failed to find clock controller DT node\n",
76 pr_err("%s: failed to map clock registers\n", __func__);
|
| /linux-master/drivers/platform/x86/ |
| H A D | toshiba-wmi.c | 43 pr_err("Bad event status 0x%x\n", status);
121 pr_err("Failed to setup input device\n");
|
| /linux-master/drivers/pps/clients/ |
| H A D | pps-ktimer.c | 70 pr_err("cannot register PPS source\n");
|
| /linux-master/drivers/pps/ |
| H A D | kapi.c | 73 pr_err("%s: unsupported default parameters\n",
79 pr_err("%s: unspecified time format\n",
110 pr_err("%s: unable to create char device\n",
123 pr_err("%s: unable to register source\n", info->name);
|
| /linux-master/drivers/scsi/ibmvscsi_tgt/ |
| H A D | libsrp.c | 175 pr_err("fail to map %p %d\n", iue,
222 pr_err("Can't get dma memory %u\n",
233 pr_err("Error copying indirect table %d\n", err);
237 pr_err("This command uses external indirect buffer\n");
246 pr_err("fail to map %p %d\n", iue,
285 pr_err("client error. Invalid data_out_format %x\n", fmt);
331 pr_err("Unknown format %d %x\n", dir, format);
365 pr_err("invalid data format %x\n", fmt);
|
| /linux-master/drivers/scsi/qedi/ |
| H A D | qedi_dbg.c | 23 pr_err("[%s]:[%s:%d]:%d: %pV", dev_name(&qedi->pdev->dev),
26 pr_err("[0000:00:00.0]:[%s:%d]: %pV", func, line, &vaf);
116 pr_err("Unable to create sysfs %s attr, err(%d).\n",
|
| /linux-master/drivers/sh/intc/ |
| H A D | virq.c | 227 pr_err("no more free IRQs, bailing..\n");
|
| /linux-master/drivers/slimbus/ |
| H A D | sched.c | 53 pr_err("Previous clock pause did not finish");
|
| /linux-master/drivers/soc/renesas/ |
| H A D | r9a06g032-smp.c | 59 pr_err("CPU#1: missing device tree node\n");
82 pr_err("CPU#1: invalid cpu-release-addr property\n");
|
| /linux-master/drivers/soc/tegra/fuse/ |
| H A D | speedo-tegra114.c | 58 pr_err("Tegra Unknown SKU %d\n", sku);
|
| H A D | speedo-tegra30.c | 143 pr_err("Tegra Unknown pkg %d\n", package_id);
160 pr_err("Tegra Unknown pkg %d\n", package_id);
177 pr_err("Tegra Unknown pkg %d\n", package_id);
214 pr_err("Tegra Unknown pkg %d\n", package_id);
|
| /linux-master/drivers/ssb/ |
| H A D | driver_chipcommon_sflash.c | 122 pr_err("Unsupported ST serial flash (id: 0x%X, id2: 0x%X)\n",
137 pr_err("Unsupported Atmel serial flash (id: 0x%X)\n",
144 pr_err("Unsupported flash type\n");
|
| H A D | ssb_private.h | 206 pr_err("Serial flash not supported\n");
|
| /linux-master/drivers/staging/olpc_dcon/ |
| H A D | olpc_dcon_xo_1.c | 50 pr_err("failed to request %s GPIO: %d\n", pin[i].name,
97 pr_err("failed to request DCON's irq\n");
|
| H A D | olpc_dcon_xo_1_5.c | 103 pr_err("failed to request %s GPIO: %d\n", pin[i].name,
123 pr_err("DCON (IRQ%d) allocation failed\n", irq);
|