| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-omap2/ |
| H A D | board-rx51-peripherals.c | 505 gpio_request(gpio + 6, "backlight_pwm");
507 gpio_request(gpio + 7, "speaker_en");
859 ret = gpio_request(RX51_WL1251_POWER_GPIO, "wl1251 power");
867 ret = gpio_request(RX51_WL1251_IRQ_GPIO, "wl1251 irq");
|
| H A D | board-ldp.c | 207 if (gpio_request(ts_gpio, "ads7846 irq") < 0) {
268 if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-orion5x/ |
| H A D | edmini_v2-setup.c | 238 if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
|
| H A D | mss2-setup.c | 250 if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
|
| H A D | ts409-setup.c | 297 if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) {
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-pxa/ |
| H A D | gumstix.c | 155 err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
|
| H A D | zylonite_pxa300.c | 200 gpio_request(gpio, "LCD_ID_PINS");
|
| H A D | poodle.c | 237 err = gpio_request(POODLE_GPIO_SD_PWR, "SD_PWR");
241 err = gpio_request(POODLE_GPIO_SD_PWR1, "SD_PWR1");
|
| H A D | stargate2.c | 693 err = gpio_request(SG2_SD_POWER_ENABLE, "SG2_sd_power_enable");
700 err = gpio_request(SG2_GPIO_nSD_DETECT, "SG2_sd_detect");
799 err = gpio_request(SG2_BT_RESET, "SG2_BT_RESET");
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-s3c2412/ |
| H A D | mach-smdk2413.c | 136 WARN_ON(gpio_request(S3C2410_GPF(2), "udc pull"));
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-u300/include/mach/ |
| H A D | gpio.h | 262 extern int gpio_request(unsigned gpio, const char *label);
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-u300/ |
| H A D | mmc.c | 116 ret = gpio_request(U300_GPIO_PIN_MMC_CD, "MMC card detection");
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/plat-mxc/ |
| H A D | 3ds_debugboard.c | 179 gpio_request(MXC_IRQ_TO_GPIO(p_irq), "expio_pirq");
|
| H A D | iomux-v1.c | 181 ret = gpio_request(gpio, label);
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/drivers/usb/otg/ |
| H A D | gpio_vbus.c | 243 err = gpio_request(gpio, "vbus_detect");
262 err = gpio_request(gpio, "udc_pullup");
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/drivers/spi/ |
| H A D | spi_gpio.c | 234 status = gpio_request(cs, dev_name(&spi->dev));
262 value = gpio_request(pin, label);
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/sound/soc/blackfin/ |
| H A D | bf5xx-ac97.c | 218 gpio_request(gpio, "bf5xx-ac97");
325 if (gpio_request(CONFIG_SND_BF5XX_RESET_GPIO_NUM, "SND_AD198x RESET")) {
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/sound/soc/omap/ |
| H A D | n810.c | 394 BUG_ON((gpio_request(N810_HEADSET_AMP_GPIO, "hs_amp") < 0) ||
395 (gpio_request(N810_SPEAKER_AMP_GPIO, "spk_amp") < 0));
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/sound/soc/s3c24xx/ |
| H A D | neo1973_gta02_wm8753.c | 458 ret = gpio_request(GTA02_GPIO_HP_IN, "GTA02_HP_IN");
470 ret = gpio_request(GTA02_GPIO_AMP_SHUT, "GTA02_AMP_SHUT");
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-imx/ |
| H A D | mach-pca100.c | 414 gpio_request(OTG_PHY_CS_GPIO, "usb-otg-cs");
416 gpio_request(USBH2_PHY_CS_GPIO, "usb-host2-cs");
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-omap1/ |
| H A D | board-h2.c | 314 if (gpio_request(0, "SMC91x irq") < 0) {
383 if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
|
| H A D | board-h3.c | 367 if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
403 if (gpio_request(40, "SMC91x irq") < 0) {
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-s3c2410/ |
| H A D | mach-n30.c | 559 WARN_ON(gpio_request(S3C2410_GPG(4), "mmc power"));
600 WARN_ON(gpio_request(S3C2410_GPB(3), "udc pup"));
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/arch/arm/mach-ep93xx/ |
| H A D | core.c | 601 err = gpio_request(EP93XX_GPIO_LINE_EGPIO14,
721 err = gpio_request(EP93XX_GPIO_LINE_C(i), dev_name(&pdev->dev));
724 err = gpio_request(EP93XX_GPIO_LINE_D(i), dev_name(&pdev->dev));
|
| /netgear-R7000-V1.0.7.12_1.2.5/components/opensource/linux/linux-2.6.36/drivers/staging/dream/ |
| H A D | gpio_matrix.c | 327 err = gpio_request(mi->output_gpios[i], "gpio_kp_out");
329 pr_err("gpiomatrix: gpio_request failed for "
345 err = gpio_request(mi->input_gpios[i], "gpio_kp_in");
347 pr_err("gpiomatrix: gpio_request failed for "
|