Searched hist:192923 (Results 1 - 9 of 9) sorted by relevance

/freebsd-10.0-release/share/man/man4/
H A Dmulticast.4diff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A DMakefilediff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
/freebsd-10.0-release/usr.sbin/ifmcstat/
H A Difmcstat.8diff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A Difmcstat.cdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
/freebsd-10.0-release/sys/netinet6/
H A Din6_mcast.cdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A Din6.hdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A Dmld6.cdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A Dicmp6.cdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.
H A Dip6_input.cdiff 192923 Wed May 27 17:11:05 MDT 2009 bms Merge final round of MLD changes from p4:
ip6_input.c, in6.h:
* Add netinet6-specific mbuf flag M_RTALERT_MLD, shadowing M_PROTO6.
* Always set this flag if HBH Router Alert option is present for MLD,
even when not forwarding.

icmp6.c:
* In icmp6_input(), spell m->m_pkthdr.rcvif as ifp to be consistent.
* Use scope ID for verifying input. Do not apply SSM filters here, no inpcb.
* Check for M_RTALERT_MLD when validating MLD traffic, as we can't see
IPv6 hop options outside of ip6_input().

in6_mcast.c:
* Use KAME scope/zone ID in in6_multi.
* Update net.inet6.ip6.mcast.filters implementation to use scope IDs
for comparisons.
* Fix scope ID treatment in multicast socket option processing.
Scope IDs passed in from userland will be ignored as other less
ambiguous APIs exist for specifying the link.
* Tighten userland input checks in IPv6 SSM delta and full-state ops.
* Source filter embedded scope IDs need to be revisited, for now
just clear them and ignore them on input.
* Adapt KAME behaviour of looking up the scope ID in the default zone
for multicast leaves, when the interface is ambiguous.

mld6.c:
* Tighten origin checks on MLD traffic as per RFC3810 Section 6.2:
* ip6_src MAY be the unspecified address for MLDv1 reports.
* ip6_src MAY have link-local address scope for MLDv1 reports,
MLDv1 queries, and MLDv2 queries.
* Perform address field validation *before* accepting queries.
* Use KAME scope/zone ID in query/report processing.
* Break const correctness for mld_v1_input_report(), mld_v1_input_query()
as we temporarily modify the input mbuf chain.
* Clear the scope ID before handoff to userland MLD daemon.
* Fix MLDv1 old querier present timer processing.
With the protocol defaults, hosts should revert to MLDv2 after 260s.
* Add net.inet6.mld.v1enable sysctl, default to on.

ifmcstat.c:
* Use sysctl by default; -K requests kvm(3) if so compiled.

mld.4:
* Connect man page to build.

Tested using PCS.

Completed in 268 milliseconds