Searched hist:318148 (Results 1 - 4 of 4) sorted by relevance
| /freebsd-11-stable/sys/dev/isp/ | ||
| H A D | ispmbox.h | diff 318148 Wed May 10 19:10:37 MDT 2017 ken MFC r317740: Correct loop mode CRN resets to adhere to FCP-4 section 4.10 Prior to this change, the CRN (Command Reference Number) is reset on any firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which specifies that the CRN should only be reset in response to a LIP Reset (LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS actions as conditions for resetting the CRN for the associated initiator port. These violations manifest themselves when the HBA is removed from the loop, or a target device is removed (especially during an outstanding command) without power cycling. If the HBA and and the target device determine upon re-establishing the loop that no PLOGI or PRLI is required, and the target does not issue a LIPxy to the initiator, the CRN for the target will have been improperly reset by the isp driver. As a result, the target port will silently ignore all FCP commands issued during the device probe (which will time out) preventing the device from attaching. This change corrects thie CRN reset behavior in response to loop state changes, also introduces CRN resets for the above mentioned ELS actions as encountered through async PDB change events. This change also adds cleanup of outstanding commands in isp_loop_dead() that was previously missing. sys/dev/isp/isp.c Add the last login state to debug output when syncing the pdb sys/dev/isp/isp_freebsd.c Replace binary statement setting aborted ccb status in isp_watchdog() with the XS_SETERR macro used elsewhere In isp_loop_dead(), abort or complete pending commands as done in isp_watchdog() In isp_async(), segregate the ISPASYNC_LOOP_RESET action from ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP fallthroughs, and only reset the CRN in the RESET case. Also add checks to handle false LOOP RESET actions that do not have a proper associated LIP primitive, and log the primitive in the debug messages In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and only reset the CRN in the DEV_CHANGED action In isp_async(), when processing an ISPASYNC_CHANGE_PDB status, reset CRN(s) for the associated nphdl (or all ports) if the change reason is some form of ELS login/logout. Also remove assignment to fc since it is not used in the scope sys/dev/isp/ispmbox.h Add macro definition for the global N-Port handle, and correct a macro typo 'PDB24XX_AE_PRLI_DONJE' sys/dev/isp/ispvar.h Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for more legible code when determining if an AL_PD port matches the portid for a given struct fcparam* by value or by virtue of the AL_PD port being 0xFF Submitted by: Reid Linnemann Sponsored by: Spectra Logic |
| H A D | ispvar.h | diff 318148 Wed May 10 19:10:37 MDT 2017 ken MFC r317740: Correct loop mode CRN resets to adhere to FCP-4 section 4.10 Prior to this change, the CRN (Command Reference Number) is reset on any firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which specifies that the CRN should only be reset in response to a LIP Reset (LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS actions as conditions for resetting the CRN for the associated initiator port. These violations manifest themselves when the HBA is removed from the loop, or a target device is removed (especially during an outstanding command) without power cycling. If the HBA and and the target device determine upon re-establishing the loop that no PLOGI or PRLI is required, and the target does not issue a LIPxy to the initiator, the CRN for the target will have been improperly reset by the isp driver. As a result, the target port will silently ignore all FCP commands issued during the device probe (which will time out) preventing the device from attaching. This change corrects thie CRN reset behavior in response to loop state changes, also introduces CRN resets for the above mentioned ELS actions as encountered through async PDB change events. This change also adds cleanup of outstanding commands in isp_loop_dead() that was previously missing. sys/dev/isp/isp.c Add the last login state to debug output when syncing the pdb sys/dev/isp/isp_freebsd.c Replace binary statement setting aborted ccb status in isp_watchdog() with the XS_SETERR macro used elsewhere In isp_loop_dead(), abort or complete pending commands as done in isp_watchdog() In isp_async(), segregate the ISPASYNC_LOOP_RESET action from ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP fallthroughs, and only reset the CRN in the RESET case. Also add checks to handle false LOOP RESET actions that do not have a proper associated LIP primitive, and log the primitive in the debug messages In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and only reset the CRN in the DEV_CHANGED action In isp_async(), when processing an ISPASYNC_CHANGE_PDB status, reset CRN(s) for the associated nphdl (or all ports) if the change reason is some form of ELS login/logout. Also remove assignment to fc since it is not used in the scope sys/dev/isp/ispmbox.h Add macro definition for the global N-Port handle, and correct a macro typo 'PDB24XX_AE_PRLI_DONJE' sys/dev/isp/ispvar.h Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for more legible code when determining if an AL_PD port matches the portid for a given struct fcparam* by value or by virtue of the AL_PD port being 0xFF Submitted by: Reid Linnemann Sponsored by: Spectra Logic |
| H A D | isp_freebsd.c | diff 318148 Wed May 10 19:10:37 MDT 2017 ken MFC r317740: Correct loop mode CRN resets to adhere to FCP-4 section 4.10 Prior to this change, the CRN (Command Reference Number) is reset on any firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which specifies that the CRN should only be reset in response to a LIP Reset (LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS actions as conditions for resetting the CRN for the associated initiator port. These violations manifest themselves when the HBA is removed from the loop, or a target device is removed (especially during an outstanding command) without power cycling. If the HBA and and the target device determine upon re-establishing the loop that no PLOGI or PRLI is required, and the target does not issue a LIPxy to the initiator, the CRN for the target will have been improperly reset by the isp driver. As a result, the target port will silently ignore all FCP commands issued during the device probe (which will time out) preventing the device from attaching. This change corrects thie CRN reset behavior in response to loop state changes, also introduces CRN resets for the above mentioned ELS actions as encountered through async PDB change events. This change also adds cleanup of outstanding commands in isp_loop_dead() that was previously missing. sys/dev/isp/isp.c Add the last login state to debug output when syncing the pdb sys/dev/isp/isp_freebsd.c Replace binary statement setting aborted ccb status in isp_watchdog() with the XS_SETERR macro used elsewhere In isp_loop_dead(), abort or complete pending commands as done in isp_watchdog() In isp_async(), segregate the ISPASYNC_LOOP_RESET action from ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP fallthroughs, and only reset the CRN in the RESET case. Also add checks to handle false LOOP RESET actions that do not have a proper associated LIP primitive, and log the primitive in the debug messages In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and only reset the CRN in the DEV_CHANGED action In isp_async(), when processing an ISPASYNC_CHANGE_PDB status, reset CRN(s) for the associated nphdl (or all ports) if the change reason is some form of ELS login/logout. Also remove assignment to fc since it is not used in the scope sys/dev/isp/ispmbox.h Add macro definition for the global N-Port handle, and correct a macro typo 'PDB24XX_AE_PRLI_DONJE' sys/dev/isp/ispvar.h Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for more legible code when determining if an AL_PD port matches the portid for a given struct fcparam* by value or by virtue of the AL_PD port being 0xFF Submitted by: Reid Linnemann Sponsored by: Spectra Logic |
| H A D | isp.c | diff 318148 Wed May 10 19:10:37 MDT 2017 ken MFC r317740: Correct loop mode CRN resets to adhere to FCP-4 section 4.10 Prior to this change, the CRN (Command Reference Number) is reset on any firmware LIP, LOOP DOWN, or LOOP RESET event in violation of FCP-4 which specifies that the CRN should only be reset in response to a LIP Reset (LIPyx) primitive. FCP-4 also indicates PLOGI/LOGO and PRLI/PRLO ELS actions as conditions for resetting the CRN for the associated initiator port. These violations manifest themselves when the HBA is removed from the loop, or a target device is removed (especially during an outstanding command) without power cycling. If the HBA and and the target device determine upon re-establishing the loop that no PLOGI or PRLI is required, and the target does not issue a LIPxy to the initiator, the CRN for the target will have been improperly reset by the isp driver. As a result, the target port will silently ignore all FCP commands issued during the device probe (which will time out) preventing the device from attaching. This change corrects thie CRN reset behavior in response to loop state changes, also introduces CRN resets for the above mentioned ELS actions as encountered through async PDB change events. This change also adds cleanup of outstanding commands in isp_loop_dead() that was previously missing. sys/dev/isp/isp.c Add the last login state to debug output when syncing the pdb sys/dev/isp/isp_freebsd.c Replace binary statement setting aborted ccb status in isp_watchdog() with the XS_SETERR macro used elsewhere In isp_loop_dead(), abort or complete pending commands as done in isp_watchdog() In isp_async(), segregate the ISPASYNC_LOOP_RESET action from ISPASYNC_LIP, ISPASYNC_LOOP_DOWN, and ISPASYNC_LOOP_UP fallthroughs, and only reset the CRN in the RESET case. Also add checks to handle false LOOP RESET actions that do not have a proper associated LIP primitive, and log the primitive in the debug messages In isp_async(), remove the goto from ISP_ASYNC_DEV_STAYED, and only reset the CRN in the DEV_CHANGED action In isp_async(), when processing an ISPASYNC_CHANGE_PDB status, reset CRN(s) for the associated nphdl (or all ports) if the change reason is some form of ELS login/logout. Also remove assignment to fc since it is not used in the scope sys/dev/isp/ispmbox.h Add macro definition for the global N-Port handle, and correct a macro typo 'PDB24XX_AE_PRLI_DONJE' sys/dev/isp/ispvar.h Add macros FCP_AL_DA_ALL, FCP_AL_PA, and FCP_IS_DEST_ALPD for more legible code when determining if an AL_PD port matches the portid for a given struct fcparam* by value or by virtue of the AL_PD port being 0xFF Submitted by: Reid Linnemann Sponsored by: Spectra Logic |
Completed in 185 milliseconds