Searched hist:127887 (Results 1 - 4 of 4) sorted by relevance
| /freebsd-11-stable/sys/compat/ndis/ | ||
| H A D | ndis_var.h | diff 127887 Mon Apr 05 06:26:52 MDT 2004 wpaul - The MiniportReset() function can return NDIS_STATUS_PENDING, in which case we should wait for the resetdone handler to be called before returning. - When providing resources via ndis_query_resources(), uses the computed rsclen when using bcopy() to copy out the resource data rather than the caller-supplied buffer length. - Avoid using ndis_reset_nic() in if_ndis.c unless we really need to reset the NIC because of a problem. - Allow interrupts to be fielded during ndis_attach(), at least as far as allowing ndis_isr() and ndis_intrhand() to run. - Use ndis_80211_rates_ex when probing for supported rates. Technically, this isn't supposed to work since, although Microsoft added the extended rate structure with the NDIS 5.1 update, the spec still says that the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of this, it appears some drivers use it anyway. - When adding in our guessed rates, check to see if they already exist so that we avoid any duplicates. - Add a printf() to ndis_open_file() that alerts the user when a driver attempts to open a file under /compat/ndis. With these changes, I can get the driver for the SMC 2802W 54g PCI card to load and run. This board uses a Prism54G chip. Note that in order for this driver to work, you must place the supplied smc2802w.arm firmware image under /compat/ndis. (The firmware is not resident on the device.) Note that this should also allow the 3Com 3CRWE154G72 card to work as well; as far as I can tell, these cards also use a Prism54G chip. |
| H A D | subr_ndis.c | diff 127887 Mon Apr 05 06:26:52 MDT 2004 wpaul - The MiniportReset() function can return NDIS_STATUS_PENDING, in which case we should wait for the resetdone handler to be called before returning. - When providing resources via ndis_query_resources(), uses the computed rsclen when using bcopy() to copy out the resource data rather than the caller-supplied buffer length. - Avoid using ndis_reset_nic() in if_ndis.c unless we really need to reset the NIC because of a problem. - Allow interrupts to be fielded during ndis_attach(), at least as far as allowing ndis_isr() and ndis_intrhand() to run. - Use ndis_80211_rates_ex when probing for supported rates. Technically, this isn't supposed to work since, although Microsoft added the extended rate structure with the NDIS 5.1 update, the spec still says that the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of this, it appears some drivers use it anyway. - When adding in our guessed rates, check to see if they already exist so that we avoid any duplicates. - Add a printf() to ndis_open_file() that alerts the user when a driver attempts to open a file under /compat/ndis. With these changes, I can get the driver for the SMC 2802W 54g PCI card to load and run. This board uses a Prism54G chip. Note that in order for this driver to work, you must place the supplied smc2802w.arm firmware image under /compat/ndis. (The firmware is not resident on the device.) Note that this should also allow the 3Com 3CRWE154G72 card to work as well; as far as I can tell, these cards also use a Prism54G chip. |
| H A D | kern_ndis.c | diff 127887 Mon Apr 05 06:26:52 MDT 2004 wpaul - The MiniportReset() function can return NDIS_STATUS_PENDING, in which case we should wait for the resetdone handler to be called before returning. - When providing resources via ndis_query_resources(), uses the computed rsclen when using bcopy() to copy out the resource data rather than the caller-supplied buffer length. - Avoid using ndis_reset_nic() in if_ndis.c unless we really need to reset the NIC because of a problem. - Allow interrupts to be fielded during ndis_attach(), at least as far as allowing ndis_isr() and ndis_intrhand() to run. - Use ndis_80211_rates_ex when probing for supported rates. Technically, this isn't supposed to work since, although Microsoft added the extended rate structure with the NDIS 5.1 update, the spec still says that the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of this, it appears some drivers use it anyway. - When adding in our guessed rates, check to see if they already exist so that we avoid any duplicates. - Add a printf() to ndis_open_file() that alerts the user when a driver attempts to open a file under /compat/ndis. With these changes, I can get the driver for the SMC 2802W 54g PCI card to load and run. This board uses a Prism54G chip. Note that in order for this driver to work, you must place the supplied smc2802w.arm firmware image under /compat/ndis. (The firmware is not resident on the device.) Note that this should also allow the 3Com 3CRWE154G72 card to work as well; as far as I can tell, these cards also use a Prism54G chip. |
| /freebsd-11-stable/sys/dev/if_ndis/ | ||
| H A D | if_ndis.c | diff 127887 Mon Apr 05 06:26:52 MDT 2004 wpaul - The MiniportReset() function can return NDIS_STATUS_PENDING, in which case we should wait for the resetdone handler to be called before returning. - When providing resources via ndis_query_resources(), uses the computed rsclen when using bcopy() to copy out the resource data rather than the caller-supplied buffer length. - Avoid using ndis_reset_nic() in if_ndis.c unless we really need to reset the NIC because of a problem. - Allow interrupts to be fielded during ndis_attach(), at least as far as allowing ndis_isr() and ndis_intrhand() to run. - Use ndis_80211_rates_ex when probing for supported rates. Technically, this isn't supposed to work since, although Microsoft added the extended rate structure with the NDIS 5.1 update, the spec still says that the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of this, it appears some drivers use it anyway. - When adding in our guessed rates, check to see if they already exist so that we avoid any duplicates. - Add a printf() to ndis_open_file() that alerts the user when a driver attempts to open a file under /compat/ndis. With these changes, I can get the driver for the SMC 2802W 54g PCI card to load and run. This board uses a Prism54G chip. Note that in order for this driver to work, you must place the supplied smc2802w.arm firmware image under /compat/ndis. (The firmware is not resident on the device.) Note that this should also allow the 3Com 3CRWE154G72 card to work as well; as far as I can tell, these cards also use a Prism54G chip. |
Completed in 187 milliseconds