ELF(844 (444lllll8\xxxQtd/lib/ld-uClibc.so.0   ?`FlLSx\dk 8P s~̅؅ ,abort__deregister_frame_info__register_frame_infolibc.so.0strcpyioctlstdoutstrerrorstrtoulsocketfprintfstrcasecmp__uClibc_mainstderrfwrite__errno_locationexitatoistrlenopenclose_edata__bss_start__bss_start____bss_end____end___endTX\`dh l p tx| -L-Ə ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌƏ ʌ|Ə ʌtƏ ʌlƏ ʌd  --- 0Čć<@-,00S 0S 0 h@-40S ,,(0S0S3/ht6 0@@V%0O- Mp`P`0X0 P@ 0XP0 0  @0vX` ЍE-DM0@PS 0 p           @,aPP `nP ?Wb Wp p^[$\P[_ 4P;0PV 6P[ x1P| h,P X'P_ ,"P0 0P<3@  2` P P P PW$` $pTP\2~ h0 0PNDЍ0 0P1@0 0 0P1@0 0 0P`1@p0 0 0P1@(0 0@u 0{0 u0+ 0x|x0/ 0ptX0 ]l80 p0`c\0|̔l|ؔ@ē,̒P -LUsage: add [interface-name] [vlan_id] rem [vlan-name] set_flag [interface-name] [flag-num] [0 | 1] set_egress_map [vlan-name] [skb_priority] [vlan_qos] set_ingress_map [vlan-name] [skb_priority] [vlan_qos] set_name_type [name-type] * The [interface-name] is the name of the ethernet card that hosts the VLAN you are talking about. * The vlan_id is the identifier (0-4095) of the VLAN you are operating on. * skb_priority is the priority in the socket buffer (sk_buff). * vlan_qos is the 3 bit priority in the VLAN header * name-type: VLAN_PLUS_VID (vlan0005), VLAN_PLUS_VID_NO_PAD (vlan5), DEV_PLUS_VID (eth0.0005), DEV_PLUS_VID_NO_PAD (eth0.5) * bind-type: PER_DEVICE # Allows vlan 5 on eth0 and eth1 to be unique. PER_KERNEL # Forces vlan 5 to be unique across all devices. * FLAGS: 1 REORDER_HDR When this is set, the VLAN device will move the ethernet header around to make it look exactly like a real ethernet device. This may help programs such as DHCPd which read the raw ethernet packet and make assumptions about the location of bytes. If you don't need it, don't turn it on, because there will be at least a small performance degradation. Default is OFF. Expecting argc to be 3-5, inclusive. Was: %d set_name_typeVLAN_PLUS_VIDVLAN_PLUS_VID_NO_PADDEV_PLUS_VIDDEV_PLUS_VID_NO_PADInvalid name type. ERROR: if_name must be 15 characters or less. /proc/net/vlan/configWARNING: Could not open /proc/net/vlan/config. Maybe you need to load the 8021q module, or maybe you are not using PROCFS?? FATAL: Couldn't open a socket..go figure! addERROR: trying to add VLAN #%u to IF -:%s:- error: %s remERROR: trying to remove VLAN -:%s:- error: %s set_egress_mapERROR: trying to set egress map on device -:%s:- error: %s set_ingress_mapERROR: trying to set ingress map on device -:%s:- error: %s set_flagERROR: trying to set flag on device -:%s:- error: %s ERROR: trying to set name type for VLAN subsystem, error: %s Unknown command -:%s:- t5 < Člpȁ  HxLLLLLLLLLLLLLLLLLLGCC: (GNU) 3.3.2 20031005 (Debian prerelease)GCC: (Buildroot 2012.02) 4.5.3A*aeabi 7-A A ,.shstrtab.interp.hash.dynsym.dynstr.rel.dyn.rel.plt.init.text.fini.rodata.eh_frame.init_array.fini_array.jcr.dynamic.got.data.bss.comment.ARM.attributes  ȁ!) 2 ;<<6LLA88GČ M2Ԍ Uhh_llkppwtt|xxHHT$0Mp+