cam/scsi/scsi_all.c

625 scsi_op_desc(uint16_t opcode, struct scsi_inquiry_data *inq_data)
661 		 * If this is true, we have a vendor specific opcode that
664 		if ((opcode > 0xBF) || ((opcode > 0x5F) && (opcode < 0x80)))
689 		for (i = 0;i < num_ops[j] && table[j][i].opcode <= opcode; i++){
690 			if ((table[j][i].opcode == opcode)
707 scsi_op_desc(uint16_t opcode, struct scsi_inquiry_data *inq_data)
3608 	 * The top 3 bits of an opcode are the group code.  The next 5 bits
3630 			/* in this case, just print out the opcode */
7649 	scsi_cmd->opcode = TEST_UNIT_READY;
7673 	scsi_cmd->opcode = REQUEST_SENSE;
7699 	scsi_cmd->opcode = INQUIRY;
7751 		scsi_cmd->opcode = MODE_SENSE_6;
7766 		scsi_cmd->opcode = MODE_SENSE_10;
7820 		scsi_cmd->opcode = MODE_SELECT_6;
7836 		scsi_cmd->opcode = MODE_SELECT_10;
7869 	scsi_cmd->opcode = LOG_SENSE;
7903 	scsi_cmd->opcode = LOG_SELECT;
7948 	scsi_cmd->opcode = PREVENT_ALLOW;
7975 	scsi_cmd->opcode = READ_CAPACITY;
7999 	scsi_cmd->opcode = SERVICE_ACTION_IN;
8030 	scsi_cmd->opcode = REPORT_LUNS;
8056 	scsi_cmd->opcode = MAINTENANCE_IN;
8082 	scsi_cmd->opcode = MAINTENANCE_IN;
8107 	scsi_cmd->opcode = MAINTENANCE_OUT;
8146 	scsi_cmd->opcode = MAINTENANCE_OUT;
8178 	scsi_cmd->opcode = SYNCHRONIZE_CACHE;
8212 		scsi_cmd->opcode = read ? READ_6 : WRITE_6;
8231 		scsi_cmd->opcode = read ? READ_10 : WRITE_10;
8254 		scsi_cmd->opcode = read ? READ_12 : WRITE_12;
8276 		scsi_cmd->opcode = read ? READ_16 : WRITE_16;
8315 		scsi_cmd->opcode = WRITE_SAME_10;
8336 		scsi_cmd->opcode = WRITE_SAME_16;
8608 		cdb->opcode = ATA_PASS_12;
8626 		cdb->opcode = ATA_PASS_16;
8658 		cdb->opcode = VARIABLE_LEN_CDB;
8709 	ata_cmd->opcode = ATA_PASS_16;
8751 	scsi_cmd->opcode = UNMAP;
8781 	scsi_cmd->opcode = RECEIVE_DIAGNOSTIC;
8812 	scsi_cmd->opcode = SEND_DIAGNOSTIC;
8853 	scsi_cmd->opcode = SERVICE_ACTION_IN;
8881 	scsi_cmd->opcode = SERVICE_ACTION_IN;
8908 	scsi_cmd->opcode = SERVICE_ACTION_IN;
8935 	scsi_cmd->opcode = READ_BUFFER;
8965 	scsi_cmd->opcode = WRITE_BUFFER;
8994 	scsi_cmd->opcode = START_STOP_UNIT;
9031 	scsi_cmd->opcode = READ_ATTRIBUTE;
9066 	scsi_cmd->opcode = WRITE_ATTRIBUTE;
9098 	scsi_cmd->opcode = PERSISTENT_RES_IN;
9126 	scsi_cmd->opcode = PERSISTENT_RES_OUT;
9156 	scsi_cmd->opcode = SECURITY_PROTOCOL_IN;
9189 	scsi_cmd->opcode = SECURITY_PROTOCOL_OUT;
9222 	scsi_cmd->opcode = MAINTENANCE_IN;