Lines Matching refs:ELINK_DEBUG_P2
1035 ELINK_DEBUG_P2(sc, "Duplex mismatch %x vs. %x\n",
1044 ELINK_DEBUG_P2(sc, "Flow control mismatch %x vs. %x\n",
1053 ELINK_DEBUG_P2(sc, "Link speed mismatch %x vs. %x\n",
1064 ELINK_DEBUG_P2(sc, "Speed Cap mismatch %x vs. %x\n",
1077 ELINK_DEBUG_P2(sc, "Flow Ctrl AN mismatch %x vs. %x\n",
1090 ELINK_DEBUG_P2(sc, "EEE mismatch %x vs. %x\n", params->eee_mode,
1127 ELINK_DEBUG_P2(sc, "Setting EPIO pin %d to %d\n", epio_pin, en);
2224 ELINK_DEBUG_P2(sc, "Changing emac_mode from 0x%x to 0x%x\n",
3308 ELINK_DEBUG_P2(sc, "init_crd 0x%x crd 0x%x\n", init_crd, crd);
3317 ELINK_DEBUG_P2(sc, "BUG! init_crd 0x%x != crd 0x%x\n",
3351 ELINK_DEBUG_P2(sc, "PBF updated to speed %d credit %d\n",
5338 ELINK_DEBUG_P2(sc, "Begin Warpcore init, link_speed %d, "
5495 ELINK_DEBUG_P2(sc, "Setting Warpcore loopback type %x, speed %d\n",
5828 ELINK_DEBUG_P2(sc, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n",
6450 ELINK_DEBUG_P2(sc, " in elink_get_link_speed_duplex vars->link_status = %x, vars->duplex = %x\n",
6452 ELINK_DEBUG_P2(sc, " phy_link_up %x line_speed %d\n",
6565 ELINK_DEBUG_P2(sc, "PCS RX link status = 0x%x-->0x%x\n",
6587 ELINK_DEBUG_P2(sc,"an_link = %x, link_up = %x\n", an_link,
6608 ELINK_DEBUG_P2(sc, "pd = %x, link_status = %x\n",
6633 ELINK_DEBUG_P2(sc, "val = %x, link_status = %x\n",
6644 ELINK_DEBUG_P2(sc, "val = %x, link_status = %x\n",
6657 ELINK_DEBUG_P2(sc, "lane %d gp_speed 0x%x\n", lane, gp_speed);
6898 ELINK_DEBUG_P2(sc, "control reg 0x%x (after %d ms)\n", ctrl, cnt);
6945 ELINK_DEBUG_P2(sc, " 10G %x, XGXS_LINK %x\n",
7175 ELINK_DEBUG_P2(sc, "elink_set_led: port %x, mode %d\n", port, mode);
7176 ELINK_DEBUG_P2(sc, "speed 0x%x, hw_led_mode 0x%x\n",
7718 ELINK_DEBUG_P2(sc, " 10G %x, XGXS_LINK %x\n",
7848 ELINK_DEBUG_P2(sc, "vars : turn_to_run_wc_rt = %x, rsrv2 = %x\n",
7872 ELINK_DEBUG_P2(sc, "Internal link speed %d is"
8086 ELINK_DEBUG_P2(sc,
8112 ELINK_DEBUG_P2(sc,
8412 ELINK_DEBUG_P2(sc, "807x Autoneg Restart: Advertise 1G=%x, 10G=%x\n",
8437 ELINK_DEBUG_P2(sc, "807x PCS status 0x%x->0x%x\n", val2, val1);
8831 ELINK_DEBUG_P2(sc, "Setting SFP+ module power to %d using pin cfg %d\n",
9478 ELINK_DEBUG_P2(sc, "Setting Fault LED to %d using pin cfg %d\n",
9758 ELINK_DEBUG_P2(sc, "8706/8726 LASI status 0x%x--> 0x%x\n", val1, val2);
9837 ELINK_DEBUG_P2(sc, "Setting RX Equalizer to BCM8706"
10049 ELINK_DEBUG_P2(sc,
10247 ELINK_DEBUG_P2(sc, "Setting TX_CTRL1 0x%x, TX_CTRL2 0x%x\n",
11267 ELINK_DEBUG_P2(sc, "Multi_phy config = 0x%x, Media control = 0x%x\n",
11415 ELINK_DEBUG_P2(sc,
12158 ELINK_DEBUG_P2(sc,
12321 ELINK_DEBUG_P2(sc, "10G-base-T LASI status 0x%x->0x%x\n",
12327 ELINK_DEBUG_P2(sc, "10G-base-T PMA status 0x%x->0x%x\n",
12337 ELINK_DEBUG_P2(sc, "SFX7101 AN status 0x%x->Master=%x\n",
12992 ELINK_DEBUG_P2(sc,"phy->rx_preemphasis = %x, phy->tx_preemphasis = %x\n",
13282 ELINK_DEBUG_P2(sc, " addr=0x%x, mdio_ctl=0x%x\n",
13353 ELINK_DEBUG_P2(sc, "Default config phy idx %x, req_duplex config %x\n",
13961 ELINK_DEBUG_P2(sc, "(1) req_speed %d, req_flowctrl %d\n",
13963 ELINK_DEBUG_P2(sc, "(2) req_speed %d, req_flowctrl %d\n",
13992 ELINK_DEBUG_P2(sc, " params : lfa_base = %x, link_attr = %x\n",
14947 ELINK_DEBUG_P2(sc, "BP=0x%x, NP=0x%x\n", base_page,
14956 ELINK_DEBUG_P2(sc, "BP=0x%x, NP=0x%x\n", base_page, next_page);