#
500f8f9b |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Assume timekeeping is correctly handed over upon last offline idle call The timekeeping duty is handed over from the outgoing CPU on stop machine, then the oneshot tick is stopped right after. Therefore it's guaranteed that the current CPU isn't the timekeeper upon its last call to idle. Besides, calling tick_nohz_idle_stop_tick() while the dying CPU goes into idle suggests that the tick is going to be stopped while it is actually stopped already from the appropriate CPU hotplug state. Remove the confusing call and the obsolete case handling and convert it to a sanity check that verifies the above assumption. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-16-frederic@kernel.org
|
#
3f69d04e |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Shut down low-res tick from dying CPU The timekeeping duty is handed over from the outgoing CPU within stop machine. This works well if CONFIG_NO_HZ_COMMON=n or the tick is in high-res mode. However in low-res dynticks mode, the tick isn't cancelled until the clockevent is shut down, which can happen later. The tick may therefore fire again once IRQs are re-enabled on stop machine and until IRQs are disabled for good upon the last call to idle. That's so many opportunities for a timekeeper to go idle and the outgoing CPU to take over that duty. This is why tick_nohz_idle_stop_tick() is called one last time on idle if the CPU is seen offline: so that the timekeeping duty is handed over again in case the CPU has re-taken the duty. This means there are two timekeeping handovers on CPU down hotplug with different undocumented constraints and purposes: 1) A handover on stop machine for !dynticks || highres. All online CPUs are guaranteed to be non-idle and the timekeeping duty can be safely handed-over. The hrtimer tick is cancelled so it is guaranteed that in dynticks mode the outgoing CPU won't take again the duty. 2) A handover on last idle call for dynticks && lowres. Setting the duty to TICK_DO_TIMER_NONE makes sure that a CPU will take over the timekeeping. Prepare for consolidating the handover to a single place (the first one) with shutting down the low-res tick as well from tick_cancel_sched_timer() as well. This will simplify the handover and unify the tick cancellation between high-res and low-res. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-15-frederic@kernel.org
|
#
7988e5ae |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Split nohz and highres features from nohz_mode The nohz mode field tells about low resolution nohz mode or high resolution nohz mode but it doesn't tell about high resolution non-nohz mode. In order to retrieve the latter state, tick_cancel_sched_timer() must fiddle with struct hrtimer's internals to guess if the tick has been initialized in high resolution. Move instead the nohz mode field information into the tick flags and provide two new bits: one to know if the tick is in nohz mode and another one to know if the tick is in high resolution. The combination of those two flags provides all the needed informations to determine which of the three tick modes is running. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-14-frederic@kernel.org
|
#
a478ffb2 |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Move individual bit features to debuggable mask accesses The individual bitfields of struct tick_sched must be modified from IRQs disabled places, otherwise local modifications can race due to them sharing the same memory storage. The recent move of the "got_idle_tick" bitfield to its own storage shows that the use of these bitfields, as pretty as they look, can be as much error prone. In order to avoid future issues of the like and make sure that those bitfields are safely accessed, move those flags to an explicit mask along with a mutator function performing the basic IRQs disabled sanity check. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-13-frederic@kernel.org
|
#
d9b1865c |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Assume the tick can't be stopped in NOHZ_MODE_INACTIVE mode The full-nohz update function checks if the nohz mode is active before proceeding. It considers one exception though: if the tick is already stopped even though the nohz mode is inactive, it still moves on in order to update/restart the tick if needed. However in order for the tick to be stopped, the nohz_mode has to be either NOHZ_MODE_LOWRES or NOHZ_MODE_HIGHRES. Therefore it doesn't make sense to test if the tick is stopped before verifying NOHZ_MODE_INACTIVE mode. Remove the needless related condition. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-11-frederic@kernel.org
|
#
60313c21 |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick/sched: Don't clear ts::next_tick again in can_stop_idle_tick() The tick sched structure is already cleared from tick_cancel_sched_timer(), so there is no need to clear that field again. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-7-frederic@kernel.org
|
#
3650f49b |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick/sched: Rename tick_nohz_stop_sched_tick() to tick_nohz_full_stop_tick() tick_nohz_stop_sched_tick() is only about NOHZ_full and not about dynticks-idle. Reflect that in the function name to avoid confusion. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-6-frederic@kernel.org
|
#
27dc0809 |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Use IS_ENABLED() whenever possible Avoid ifdeferry if it can be converted to IS_ENABLED() whenever possible Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-5-frederic@kernel.org
|
#
3aedb7fc |
|
25-Feb-2024 |
Frederic Weisbecker <frederic@kernel.org> |
tick/sched: Remove useless oneshot ifdeffery tick-sched.c is only built when CONFIG_TICK_ONESHOT=y, which is selected only if CONFIG_NO_HZ_COMMON=y or CONFIG_HIGH_RES_TIMERS=y. Therefore the related ifdeferry in this file is needless and can be removed. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-4-frederic@kernel.org
|
#
37263ba0 |
|
25-Feb-2024 |
Peng Liu <liupeng17@lenovo.com> |
tick/nohz: Remove duplicate between lowres and highres handlers tick_nohz_lowres_handler() does the same work as tick_nohz_highres_handler() plus the clockevent device reprogramming, so make the former reuse the latter and rename it accordingly. Signed-off-by: Peng Liu <liupeng17@lenovo.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-3-frederic@kernel.org
|
#
ffb7e01c |
|
25-Feb-2024 |
Peng Liu <liupeng17@lenovo.com> |
tick/nohz: Remove duplicate between tick_nohz_switch_to_nohz() and tick_setup_sched_timer() The ts->sched_timer initialization work of tick_nohz_switch_to_nohz() is almost the same as that of tick_setup_sched_timer(), so adjust the latter to get it reused by tick_nohz_switch_to_nohz(). This also makes the low resolution mode sched_timer benefit from the tick skew boot option. Signed-off-by: Peng Liu <liupeng17@lenovo.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240225225508.11587-2-frederic@kernel.org
|
#
4c532939 |
|
21-Feb-2024 |
Richard Cochran (linutronix GmbH) <richardcochran@gmail.com> |
tick/sched: Split out jiffies update helper function The logic to get the time of the last jiffies update will be needed by the timer pull model as well. Move the code into a global function in anticipation of the new caller. No functional change. Signed-off-by: Richard Cochran (linutronix GmbH) <richardcochran@gmail.com> Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20240221090548.36600-17-anna-maria@linutronix.de
|
#
73129cf4 |
|
21-Feb-2024 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
timers: Optimization for timer_base_try_to_set_idle() When tick is stopped also the timer base is_idle flag is set. When reentering timer_base_try_to_set_idle() with the tick stopped, there is no need to check whether the timer base needs to be set idle again. When a timer was enqueued in the meantime, this is already handled by the tick_nohz_next_event() call which was executed before tick_nohz_stop_tick(). Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20240221090548.36600-5-anna-maria@linutronix.de
|
#
e2e1d724 |
|
21-Feb-2024 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
timers: Move marking timer bases idle into tick_nohz_stop_tick() The timer base is marked idle when get_next_timer_interrupt() is executed. But the decision whether the tick will be stopped and whether the system is able to go idle is done later. When the timer bases is marked idle and a new first timer is enqueued remote an IPI is raised. Even if it is not required because the tick is not stopped and the timer base is evaluated again at the next tick. To prevent this, the timer base is marked idle in tick_nohz_stop_tick() and get_next_timer_interrupt() is streamlined by only looking for the next timer interrupt. All other work is postponed to timer_base_try_to_set_idle() which is called by tick_nohz_stop_tick(). timer_base_try_to_set_idle() never resets timer_base::is_idle state. This is done when the tick is restarted via tick_nohz_restart_sched_tick(). With this, tick_sched::tick_stopped and timer_base::is_idle are always in sync. So there is no longer the need to execute timer_clear_idle() in tick_nohz_idle_retain_tick(). This was required before, as tick_nohz_next_event() set timer_base::is_idle even if the tick would not be stopped. So timer_clear_idle() is only executed, when timer base is idle. So the check whether timer base is idle, is now no longer required as well. While at it fix some nearby whitespace damage as well. Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20240221090548.36600-4-anna-maria@linutronix.de
|
#
f365d055 |
|
23-Jan-2024 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
tick/sched: Add function description for tick_nohz_next_event() The return value of tick_nohz_next_event() is not obvious at the first glance. Add a kernel-doc compatible function description which also covers return values. Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240123164702.55612-4-anna-maria@linutronix.de
|
#
9a574ea9 |
|
22-Jan-2024 |
Tim Chen <tim.c.chen@linux.intel.com> |
tick/sched: Preserve number of idle sleeps across CPU hotplug events Commit 71fee48f ("tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug") preserved total idle sleep time and iowait sleeptime across CPU hotplug events. Similar reasoning applies to the number of idle calls and idle sleeps to get the proper average of sleep time per idle invocation. Preserve those fields too. Fixes: 71fee48f ("tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug") Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240122233534.3094238-1-tim.c.chen@linux.intel.com
|
#
71fee48f |
|
15-Jan-2024 |
Heiko Carstens <hca@linux.ibm.com> |
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug When offlining and onlining CPUs the overall reported idle and iowait times as reported by /proc/stat jump backward and forward: cpu 132 0 176 225249 47 6 6 21 0 0 cpu0 80 0 115 112575 33 3 4 18 0 0 cpu1 52 0 60 112673 13 3 1 2 0 0 cpu 133 0 177 226681 47 6 6 21 0 0 cpu0 80 0 116 113387 33 3 4 18 0 0 cpu 133 0 178 114431 33 6 6 21 0 0 <---- jump backward cpu0 80 0 116 114247 33 3 4 18 0 0 cpu1 52 0 61 183 0 3 1 2 0 0 <---- idle + iowait start with 0 cpu 133 0 178 228956 47 6 6 21 0 0 <---- jump forward cpu0 81 0 117 114929 33 3 4 18 0 0 Reason for this is that get_idle_time() in fs/proc/stat.c has different sources for both values depending on if a CPU is online or offline: - if a CPU is online the values may be taken from its per cpu tick_cpu_sched structure - if a CPU is offline the values are taken from its per cpu cpustat structure The problem is that the per cpu tick_cpu_sched structure is set to zero on CPU offline. See tick_cancel_sched_timer() in kernel/time/tick-sched.c. Therefore when a CPU is brought offline and online afterwards both its idle and iowait sleeptime will be zero, causing a jump backward in total system idle and iowait sleeptime. In a similar way if a CPU is then brought offline again the total idle and iowait sleeptimes will jump forward. It looks like this behavior was introduced with commit 4b0c0f294f60 ("tick: Cleanup NOHZ per cpu data on cpu down"). This was only noticed now on s390, since we switched to generic idle time reporting with commit be76ea614460 ("s390/idle: remove arch_cpu_idle_time() and corresponding code"). Fix this by preserving the values of idle_sleeptime and iowait_sleeptime members of the per-cpu tick_sched structure on CPU hotplug. Fixes: 4b0c0f294f60 ("tick: Cleanup NOHZ per cpu data on cpu down") Reported-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20240115163555.1004144-1-hca@linux.ibm.com
|
#
cbf04a22 |
|
01-Dec-2023 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
tick-sched: Warn when next tick seems to be in the past When the next tick is in the past, the delta between basemono and the next tick gets negativ. But the next tick should never be in the past. The negative effect of a wrong next tick might be a stop of the tick and timers might expire late. To prevent expensive debugging when changing underlying code, add a WARN_ON_ONCE into this code path. To prevent complete misbehaviour, also reset next_tick to basemono in this case. Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20231201092654.34614-4-anna-maria@linutronix.de
|
#
31805067 |
|
01-Dec-2023 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
tick/sched: Cleanup confusing variables tick_nohz_stop_tick() contains the expires (u64 variable) and tick (ktime_t) variable. In the beginning the value of expires is written to tick. Afterwards none of the variables is changed. They are only used for checks. Drop the not required variable tick and use always expires instead. Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20231201092654.34614-3-anna-maria@linutronix.de
|
#
cb665db9 |
|
01-Dec-2023 |
Anna-Maria Behnsen <anna-maria@linutronix.de> |
tick-sched: Fix function names in comments When referencing functions in comments, it might be helpful to use full function names (including the prefix) to be able to find it when grepping. Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20231201092654.34614-2-anna-maria@linutronix.de
|
#
6c774377 |
|
28-Sep-2023 |
Ingo Molnar <mingo@kernel.org> |
tick/nohz: Update comments some more Inspired by recent enhancements to comments in kernel/time/tick-sched.c, go through the entire file and fix/unify its comments: - Fix over a dozen typos, spelling mistakes & cases of bad grammar. - Re-phrase sentences that I needed to read three times to understand. [ I used the following arbitrary rule-of-thumb: - if I had to read a comment twice, it was usually my fault, - if I had to read it a third time, it was the comment's fault. ] - Comma updates: - Add commas where needed - Remove commas where not needed - In cases where a comma is optional, choose one variant and try to standardize it over similar sentences in the file. - Standardize on standalone 'NOHZ' spelling in free-flowing comments: s/nohz/NOHZ s/no idle tick/NOHZ Still keep 'dynticks' as a popular synonym. - Standardize on referring to variable names within free-flowing comments with the "'var'" nomenclature, and function names as "function_name()". - Standardize on '64-bit' and '32-bit': s/32bit/32-bit s/64bit/64-bit - Standardize on 'IRQ work': s/irq work/IRQ work - A few other tidyups I probably missed to list. No change in functionality intended - other than one small change to a syslog output string. Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/ZRVCNeMcSQcXS36N@gmail.com
|
#
4f7f4409 |
|
11-Sep-2023 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Don't shutdown the lowres tick from itself In lowres dynticks mode, just like in highres dynticks mode, when there is no tick to program in the future, the tick eventually gets deactivated either: * From the idle loop if in idle mode. * From the IRQ exit if in full dynticks mode. Therefore there is no need to deactivate it from the tick itself. This just just brings more overhead in the idle tick path for no reason. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Link: https://lore.kernel.org/r/20230912104406.312185-4-frederic@kernel.org
|
#
822deeed |
|
11-Sep-2023 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Update obsolete comments Some comments are obsolete enough to assume that IRQ exit restarts the tick in idle or RCU is turned on at the same time as the tick, among other details. Update them and add more. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20230912104406.312185-3-frederic@kernel.org
|
#
dba428a6 |
|
11-Sep-2023 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Rename the tick handlers to more self-explanatory names The current names of the tick handlers don't tell much about what different between them. Use names that better reflect their role and resolution. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20230912104406.312185-2-frederic@kernel.org
|
#
96c1fa04 |
|
18-Aug-2023 |
Paul Gortmaker <paul.gortmaker@windriver.com> |
tick/rcu: Fix false positive "softirq work is pending" messages In commit 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") the new function report_idle_softirq() was created by breaking code out of the existing can_stop_idle_tick() for kernels v5.18 and newer. In doing so, the code essentially went from a one conditional: if (a && b && c) warn(); to a three conditional: if (!a) return; if (!b) return; if (!c) return; warn(); But that conversion got the condition for the RT specific local_bh_blocked() wrong. The original condition was: !local_bh_blocked() but the conversion failed to negate it so it ended up as: if (!local_bh_blocked()) return false; This issue lay dormant until another fixup for the same commit was added in commit a7e282c77785 ("tick/rcu: Fix bogus ratelimit condition"). This commit realized the ratelimit was essentially set to zero instead of ten, and hence *no* softirq pending messages would ever be issued. Once this commit was backported via linux-stable, both the v6.1 and v6.4 preempt-rt kernels started printing out 10 instances of this at boot: NOHZ tick-stop error: local softirq work is pending, handler #80!!! Remove the negation and return when local_bh_blocked() evaluates to true to bring the correct behaviour back. Fixes: 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by: Wen Yang <wenyang.linux@foxmail.com> Acked-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20230818200757.1808398-1-paul.gortmaker@windriver.com
|
#
a7e282c7 |
|
04-May-2023 |
Wen Yang <wenyang.linux@foxmail.com> |
tick/rcu: Fix bogus ratelimit condition The ratelimit logic in report_idle_softirq() is broken because the exit condition is always true: static int ratelimit; if (ratelimit < 10) return false; ---> always returns here ratelimit++; ---> no chance to run Make it check for >= 10 instead. Fixes: 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle") Signed-off-by: Wen Yang <wenyang.linux@foxmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/tencent_5AAA3EEAB42095C9B7740BE62FBF9A67E007@qq.com
|
#
13bb06f8 |
|
15-Jun-2023 |
Thomas Gleixner <tglx@linutronix.de> |
tick/common: Align tick period during sched_timer setup The tick period is aligned very early while the first clock_event_device is registered. At that point the system runs in periodic mode and switches later to one-shot mode if possible. The next wake-up event is programmed based on the aligned value (tick_next_period) but the delta value, that is used to program the clock_event_device, is computed based on ktime_get(). With the subtracted offset, the device fires earlier than the exact time frame. With a large enough offset the system programs the timer for the next wake-up and the remaining time left is too small to make any boot progress. The system hangs. Move the alignment later to the setup of tick_sched timer. At this point the system switches to oneshot mode and a high resolution clocksource is available. At this point it is safe to align tick_next_period because ktime_get() will now return accurate (not jiffies based) time. [bigeasy: Patch description + testing]. Fixes: e9523a0d81899 ("tick/common: Align tick period with the HZ tick.") Reported-by: Mathias Krause <minipli@grsecurity.net> Reported-by: "Bhatnagar, Rishabh" <risbhat@amazon.com> Suggested-by: Mathias Krause <minipli@grsecurity.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Richard W.M. Jones <rjones@redhat.com> Tested-by: Mathias Krause <minipli@grsecurity.net> Acked-by: SeongJae Park <sj@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/5a56290d-806e-b9a5-f37c-f21958b5a8c0@grsecurity.net Link: https://lore.kernel.org/12c6f9a3-d087-b824-0d05-0d18c9bc1bf3@amazon.com Link: https://lore.kernel.org/r/20230615091830.RxMV2xf_@linutronix.de
|
#
289dafed |
|
22-Feb-2023 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Remove middle-function __tick_nohz_idle_stop_tick() There is no need for the __tick_nohz_idle_stop_tick() function between tick_nohz_idle_stop_tick() and its implementation. Remove that unnecessary step. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20230222144649.624380-6-frederic@kernel.org
|
#
ead70b75 |
|
22-Feb-2023 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Add a comment about broken iowait counter update race The per-cpu iowait task counter is incremented locally upon sleeping. But since the task can be woken to (and by) another CPU, the counter may then be decremented remotely. This is the source of a race involving readers VS writer of idle/iowait sleeptime. The following scenario shows an example where a /proc/stat reader observes a pending sleep time as IO whereas that pending sleep time later eventually gets accounted as non-IO. CPU 0 CPU 1 CPU 2 ----- ----- ------ //io_schedule() TASK A current->in_iowait = 1 rq(0)->nr_iowait++ //switch to idle // READ /proc/stat // See nr_iowait_cpu(0) == 1 return ts->iowait_sleeptime + ktime_sub(ktime_get(), ts->idle_entrytime) //try_to_wake_up(TASK A) rq(0)->nr_iowait-- //idle exit // See nr_iowait_cpu(0) == 0 ts->idle_sleeptime += ktime_sub(ktime_get(), ts->idle_entrytime) As a result subsequent reads on /proc/stat may expose backward progress. This is unfortunately hardly fixable. Just add a comment about that condition. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20230222144649.624380-5-frederic@kernel.org
|
#
620a30fa |
|
22-Feb-2023 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Protect idle/iowait sleep time under seqcount Reading idle/IO sleep time (eg: from /proc/stat) can race with idle exit updates because the state machine handling the stats is not atomic and requires a coherent read batch. As a result reading the sleep time may report irrelevant or backward values. Fix this with protecting the simple state machine within a seqcount. This is expected to be cheap enough not to add measurable performance impact on the idle path. Note this only fixes reader VS writer condition partitially. A race remains that involves remote updates of the CPU iowait task counter. It can hardly be fixed. Reported-by: Yu Liao <liaoyu15@huawei.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20230222144649.624380-4-frederic@kernel.org
|
#
07b65a80 |
|
22-Feb-2023 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Only ever update sleeptime from idle exit The idle and IO sleeptime statistics appearing in /proc/stat can be currently updated from two sites: locally on idle exit and remotely by cpufreq. However there is no synchronization mechanism protecting concurrent updates. It is therefore possible to account the sleeptime twice, among all the other possible broken scenarios. To prevent from breaking the sleeptime accounting source, restrict the sleeptime updates to the local idle exit site. If there is a delta to add since the last update, IO/Idle sleep time readers will now only compute the delta without actually writing it back to the internal idle statistic fields. This fixes a writer VS writer race. Note there are still two known reader VS writer races to handle. A subsequent patch will fix one. Reported-by: Yu Liao <liaoyu15@huawei.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20230222144649.624380-3-frederic@kernel.org
|
#
db7b464d |
|
20-Dec-2022 |
Zqiang <qiang1.zhang@intel.com> |
rcu: Fix missing TICK_DEP_MASK_RCU_EXP dependency check This commit adds checks for the TICK_DEP_MASK_RCU_EXP bit, thus enabling RCU expedited grace periods to actually force-enable scheduling-clock interrupts on holdout CPUs. Fixes: df1e849ae455 ("rcu: Enable tick for nohz_full CPUs slow to provide expedited QS") Signed-off-by: Zqiang <qiang1.zhang@intel.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Anna-Maria Behnsen <anna-maria@linutronix.de> Acked-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
|
#
58d76682 |
|
24-Jan-2023 |
Joel Fernandes (Google) <joel@joelfernandes.org> |
tick/nohz: Fix cpu_is_hotpluggable() by checking with nohz subsystem For CONFIG_NO_HZ_FULL systems, the tick_do_timer_cpu cannot be offlined. However, cpu_is_hotpluggable() still returns true for those CPUs. This causes torture tests that do offlining to end up trying to offline this CPU causing test failures. Such failure happens on all architectures. Fix the repeated error messages thrown by this (even if the hotplug errors are harmless) by asking the opinion of the nohz subsystem on whether the CPU can be hotplugged. [ Apply Frederic Weisbecker feedback on refactoring tick_nohz_cpu_down(). ] For drivers/base/ portion: Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Frederic Weisbecker <frederic@kernel.org> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Zhouyi Zhou <zhouzhouyi@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: rcu <rcu@vger.kernel.org> Cc: stable@vger.kernel.org Fixes: 2987557f52b9 ("driver-core/cpu: Expose hotpluggability to the rest of the kernel") Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
|
#
2a0aafce |
|
08-Jun-2022 |
Frederic Weisbecker <frederic@kernel.org> |
context_tracking: Rename context_tracking_cpu_set() to ct_cpu_track_user() context_tracking_cpu_set() is called in order to tell a CPU to track user/kernel transitions. Since context tracking is going to expand in to also track transitions from/to idle/IRQ/NMIs, the scope of this function name becomes too broad and needs to be made more specific. Also shorten the prefix to align with the new namespace. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
|
#
23900951 |
|
26-Jun-2022 |
Masahiro Yamada <masahiroy@kernel.org> |
tick/nohz: unexport __init-annotated tick_nohz_full_setup() EXPORT_SYMBOL and __init is a bad combination because the .init.text section is freed up after the initialization. Hence, modules cannot use symbols annotated __init. The access to a freed symbol may end up with kernel panic. modpost used to detect it, but it had been broken for a decade. Commit 28438794aba4 ("modpost: fix section mismatch check for exported init/exit sections") fixed it so modpost started to warn it again, then this showed up: MODPOST vmlinux.symvers WARNING: modpost: vmlinux.o(___ksymtab_gpl+tick_nohz_full_setup+0x0): Section mismatch in reference from the variable __ksymtab_tick_nohz_full_setup to the function .init.text:tick_nohz_full_setup() The symbol tick_nohz_full_setup is exported and annotated __init Fix this by removing the __init annotation of tick_nohz_full_setup or drop the export. Drop the export because tick_nohz_full_setup() is only called from the built-in code in kernel/sched/isolation.c. Fixes: ae9e557b5be2 ("time: Export tick start/stop functions for rcutorture") Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
62c1256d |
|
22-Apr-2022 |
Nicholas Piggin <npiggin@gmail.com> |
timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick is stopped When tick_nohz_stop_tick() stops the tick and high resolution timers are disabled, then the clock event device is not put into ONESHOT_STOPPED mode. This can lead to spurious timer interrupts with some clock event device drivers that don't shut down entirely after firing. Eliminate these by putting the device into ONESHOT_STOPPED mode at points where it is not being reprogrammed. When there are no timers active, then tick_program_event() with KTIME_MAX can be used to stop the device. When there is a timer active, the device can be stopped at the next tick (any new timer added by timers will reprogram the tick). Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220422141446.915024-1-npiggin@gmail.com
|
#
9c95bc25 |
|
14-Feb-2022 |
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> |
tick/sched: Fix non-kernel-doc comment Fixes the following W=1 kernel build warning: kernel/time/tick-sched.c:1563: warning: This comment starts with '/**', but isn't a kernel-doc comment. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220214084739.63228-1-jiapeng.chong@linux.alibaba.com
|
#
40e97e42 |
|
06-Dec-2021 |
Paul Gortmaker <paul.gortmaker@windriver.com> |
tick/nohz: Use WARN_ON_ONCE() to prevent console saturation While running some testing on code that happened to allow the variable tick_nohz_full_running to get set but with no "possible" NOHZ cores to back up that setting, this warning triggered: if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE)) WARN_ON(tick_nohz_full_running); The console was overwhemled with an endless stream of one WARN per tick per core and there was no way to even see what was going on w/o using a serial console to capture it and then trace it back to this. Change it to WARN_ON_ONCE(). Fixes: 08ae95f4fd3b ("nohz_full: Allow the boot CPU to be nohz_full") Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211206145950.10927-3-paul.gortmaker@windriver.com
|
#
0345691b |
|
08-Feb-2022 |
Frederic Weisbecker <frederic@kernel.org> |
tick/rcu: Stop allowing RCU_SOFTIRQ in idle RCU_SOFTIRQ used to be special in that it could be raised on purpose within the idle path to prevent from stopping the tick. Some code still prevents from unnecessary warnings related to this specific behaviour while entering in dynticks-idle mode. However the nohz layout has changed quite a bit in ten years, and the removal of CONFIG_RCU_FAST_NO_HZ has been the final straw to this safe-conduct. Now the RCU_SOFTIRQ vector is expected to be raised from sane places. A remaining corner case is admitted though when the vector is invoked in fragile hotplug path. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Paul Menzel <pmenzel@molgen.mpg.de>
|
#
29845399 |
|
08-Feb-2022 |
Frederic Weisbecker <frederic@kernel.org> |
tick/rcu: Remove obsolete rcu_needs_cpu() parameters With the removal of CONFIG_RCU_FAST_NO_HZ, the parameters in rcu_needs_cpu() are not necessary anymore. Simply remove them. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Paul Menzel <pmenzel@molgen.mpg.de>
|
#
a1ff03cd |
|
01-Feb-2022 |
Frederic Weisbecker <frederic@kernel.org> |
tick: Detect and fix jiffies update stall On some rare cases, the timekeeper CPU may be delaying its jiffies update duty for a while. Known causes include: * The timekeeper is waiting on stop_machine in a MULTI_STOP_DISABLE_IRQ or MULTI_STOP_RUN state. Disabled interrupts prevent from timekeeping updates while waiting for the target CPU to complete its stop_machine() callback. * The timekeeper vcpu has VMEXIT'ed for a long while due to some overload on the host. Detect and fix these situations with emergency timekeeping catchups. Original-patch-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
53e87e3c |
|
26-Oct-2021 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Last resort update jiffies on nohz_full IRQ entry When at least one CPU runs in nohz_full mode, a dedicated timekeeper CPU is guaranteed to stay online and to never stop its tick. Meanwhile on some rare case, the dedicated timekeeper may be running with interrupts disabled for a while, such as in stop_machine. If jiffies stop being updated, a nohz_full CPU may end up endlessly programming the next tick in the past, taking the last jiffies update monotonic timestamp as a stale base, resulting in an tick storm. Here is a scenario where it matters: 0) CPU 0 is the timekeeper and CPU 1 a nohz_full CPU. 1) A stop machine callback is queued to execute somewhere. 2) CPU 0 reaches MULTI_STOP_DISABLE_IRQ while CPU 1 is still in MULTI_STOP_PREPARE. Hence CPU 0 can't do its timekeeping duty. CPU 1 can still take IRQs. 3) CPU 1 receives an IRQ which queues a timer callback one jiffy forward. 4) On IRQ exit, CPU 1 schedules the tick one jiffy forward, taking last_jiffies_update as a base. But last_jiffies_update hasn't been updated for 2 jiffies since the timekeeper has interrupts disabled. 5) clockevents_program_event(), which relies on ktime_get(), observes that the expiration is in the past and therefore programs the min delta event on the clock. 6) The tick fires immediately, goto 3) 7) Tick storm, the nohz_full CPU is drown and takes ages to reach MULTI_STOP_DISABLE_IRQ, which is the only way out of this situation. Solve this with unconditionally updating jiffies if the value is stale on nohz_full IRQ entry. IRQs and other disturbances are expected to be rare enough on nohz_full for the unconditional call to ktime_get() to actually matter. Reported-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Paul E. McKenney <paulmck@kernel.org> Link: https://lore.kernel.org/r/20211026141055.57358-2-frederic@kernel.org
|
#
0fdcccfa |
|
12-May-2021 |
Peter Zijlstra <peterz@infradead.org> |
tick/nohz: Call tick_nohz_task_switch() with interrupts disabled Call tick_nohz_task_switch() slightly earlier after the context switch to benefit from disabled IRQs. This way the function doesn't need to disable them once more. Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20210512232924.150322-10-frederic@kernel.org
|
#
a1dfb631 |
|
12-May-2021 |
Marcelo Tosatti <mtosatti@redhat.com> |
tick/nohz: Kick only _queued_ task whose tick dependency is updated When the tick dependency of a task is updated, we want it to aknowledge the new state and restart the tick if needed. If the task is not running, we don't need to kick it because it will observe the new dependency upon scheduling in. But if the task is running, we may need to send an IPI to it so that it gets notified. Unfortunately we don't have the means to check if a task is running in a race free way. Checking p->on_cpu in a synchronized way against p->tick_dep_mask would imply adding a full barrier between prepare_task_switch() and tick_nohz_task_switch(), which we want to avoid in this fast-path. Therefore we blindly fire an IPI to the task's CPU. Meanwhile we can check if the task is queued on the CPU rq because p->on_rq is always set to TASK_ON_RQ_QUEUED _before_ schedule() and its full barrier that precedes tick_nohz_task_switch(). And if the task is queued on a nohz_full CPU, it also has fair chances to be running as the isolation constraints prescribe running single tasks on full dynticks CPUs. So use this as a trick to check if we can spare an IPI toward a non-running task. NOTE: For the ordering to be correct, it is assumed that we never deactivate a task while it is running, the only exception being the task deactivating itself while scheduling out. Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-9-frederic@kernel.org
|
#
1e4ca26d |
|
12-May-2021 |
Marcelo Tosatti <mtosatti@redhat.com> |
tick/nohz: Change signal tick dependency to wake up CPUs of member tasks Rather than waking up all nohz_full CPUs on the system, only wake up the target CPUs of member threads of the signal. Reduces interruptions to nohz_full CPUs. Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-8-frederic@kernel.org
|
#
29721b85 |
|
12-May-2021 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Only wake up a single target cpu when kicking a task When adding a tick dependency to a task, its necessary to wake up the CPU where the task resides to reevaluate tick dependencies on that CPU. However the current code wakes up all nohz_full CPUs, which is unnecessary. Switch to waking up a single CPU, by using ordering of writes to task->cpu and task->tick_dep_mask. [ mingo: Minor readability edit. ] Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-7-frederic@kernel.org
|
#
96c9b903 |
|
12-May-2021 |
Yunfeng Ye <yeyunfeng@huawei.com> |
tick/nohz: Update idle_exittime on actual idle exit The idle_exittime field of tick_sched is used to record the time when the idle state was left. but currently the idle_exittime is updated in the function tick_nohz_restart_sched_tick(), which is not always in idle state when nohz_full is configured: tick_irq_exit tick_nohz_irq_exit tick_nohz_full_update_tick tick_nohz_restart_sched_tick ts->idle_exittime = now; It's thus overwritten by mistake on nohz_full tick restart. Move the update to the appropriate idle exit path instead. Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-5-frederic@kernel.org
|
#
3f624314 |
|
12-May-2021 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Remove superflous check for CONFIG_VIRT_CPU_ACCOUNTING_NATIVE The vtime_accounting_enabled_this_cpu() early check already makes what follows as dead code in the case of CONFIG_VIRT_CPU_ACCOUNTING_NATIVE. No need to keep the ifdeferry around. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-4-frederic@kernel.org
|
#
a5183862 |
|
12-May-2021 |
Yunfeng Ye <yeyunfeng@huawei.com> |
tick/nohz: Conditionally restart tick on idle exit In nohz_full mode, switching from idle to a task will unconditionally issue a tick restart. If the task is alone in the runqueue or is the highest priority, the tick will fire once then eventually stop. But that alone is still undesired noise. Therefore, only restart the tick on idle exit when it's strictly necessary. Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20210512232924.150322-3-frederic@kernel.org
|
#
f268c373 |
|
27-May-2021 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Only check for RCU deferred wakeup on user/guest entry when needed Checking for and processing RCU-nocb deferred wakeup upon user/guest entry is only relevant when nohz_full runs on the local CPU, otherwise the periodic tick should take care of it. Make sure we don't needlessly pollute these fast-paths as a -3% performance regression on a will-it-scale.per_process_ops has been reported so far. Fixes: 47b8ff194c1f (entry: Explicitly flush pending rcuog wakeup before last rescheduling point) Fixes: 4ae7dc97f726 (entry/kvm: Explicitly flush pending rcuog wakeup before last rescheduling point) Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20210527113441.465489-1-frederic@kernel.org
|
#
4c81cb7e |
|
29-Mar-2021 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
tick/nohz: Improve tick_nohz_get_next_hrtimer() kerneldoc Make the tick_nohz_get_next_hrtimer() kerneldoc comment state clearly that the function may return negative numbers. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
4bf07f65 |
|
22-Mar-2021 |
Ingo Molnar <mingo@kernel.org> |
timekeeping, clocksource: Fix various typos in comments Fix ~56 single-word typos in timekeeping & clocksource code comments. Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: linux-kernel@vger.kernel.org
|
#
47c218dc |
|
09-Mar-2021 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Prevent false positive softirq pending warnings on RT On RT a task which has soft interrupts disabled can block on a lock and schedule out to idle while soft interrupts are pending. This triggers the warning in the NOHZ idle code which complains about going idle with pending soft interrupts. But as the task is blocked soft interrupt processing is temporarily blocked as well which means that such a warning is a false positive. To prevent that check the per CPU state which indicates that a scheduled out task has soft interrupts disabled. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20210309085727.527563866@linutronix.de
|
#
ba8ea8e7 |
|
06-Dec-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Remove bogus boot "safety" check can_stop_idle_tick() checks whether the do_timer() duty has been taken over by a CPU on boot. That's silly because the boot CPU always takes over with the initial clockevent device. But even if no CPU would have installed a clockevent and taken over the duty then the question whether the tick on the current CPU can be stopped or not is moot. In that case the current CPU would have no clockevent either, so there would be nothing to keep ticking. Remove it. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20201206212002.725238293@linutronix.de
|
#
aa3b66f4 |
|
04-Dec-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Make jiffies update quick check more robust The quick check in tick_do_update_jiffies64() whether jiffies need to be updated is not really correct under all circumstances and on all architectures, especially not on 32bit systems. The quick check does: if (now < READ_ONCE(tick_next_period)) return; and the counterpart in the update is: WRITE_ONCE(tick_next_period, next_update_time); This has two problems: 1) On weakly ordered architectures there is no guarantee that the stores before the WRITE_ONCE() are visible which means that other CPUs can operate on a stale jiffies value. 2) On 32bit the store of tick_next_period which is an u64 is split into two 32bit stores. If the first 32bit store advances tick_next_period far out and the second 32bit store is delayed (virt, NMI ...) then jiffies will become stale until the second 32bit store happens. Address this by seperating the handling for 32bit and 64bit. On 64bit problem #1 is addressed by replacing READ_ONCE() / WRITE_ONCE() with smp_load_acquire() / smp_store_release(). On 32bit problem #2 is addressed by protecting the quick check with the jiffies sequence counter. The load and stores can be plain because the sequence count mechanics provides the required barriers already. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/87czzpc02w.fsf@nanos.tec.linutronix.de
|
#
7a9f50a0 |
|
15-Jun-2020 |
Peter Zijlstra <peterz@infradead.org> |
irq_work: Cleanup Get rid of the __call_single_node union and clean up the API a little to avoid external code relying on the structure layout as much. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
#
b9965449 |
|
17-Nov-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Get rid of tick_period The variable tick_period is initialized to NSEC_PER_TICK / HZ during boot and never updated again. If NSEC_PER_TICK is not an integer multiple of HZ this computation is less accurate than TICK_NSEC which has proper rounding in place. Aside of the inaccuracy there is no reason for having this variable at all. It's just a pointless indirection and all usage sites can just use the TICK_NSEC constant. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.766643526@linutronix.de
|
#
896b969e |
|
17-Nov-2020 |
Yunfeng Ye <yeyunfeng@huawei.com> |
tick/sched: Release seqcount before invoking calc_load_global() calc_load_global() does not need the sequence count protection. [ tglx: Split it up properly and added comments ] Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.660902274@linutronix.de
|
#
7a35bf2a |
|
17-Nov-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Optimize tick_do_update_jiffies64() further Now that it's clear that there is always one tick to account, simplify the calculations some more. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.565663056@linutronix.de
|
#
94ad2e3c |
|
17-Nov-2020 |
Yunfeng Ye <yeyunfeng@huawei.com> |
tick/sched: Reduce seqcount held scope in tick_do_update_jiffies64() If jiffies are up to date already (caller lost the race against another CPU) there is no point to change the sequence count. Doing that just forces other CPUs into the seqcount retry loop in tick_nohz_next_event() for nothing. Just bail out early. [ tglx: Rewrote most of it ] Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.462195901@linutronix.de
|
#
372acbba |
|
17-Nov-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Use tick_next_period for lockless quick check No point in doing calculations. tick_next_period = last_jiffies_update + tick_period Just check whether now is before tick_next_period to figure out whether jiffies need an update. Add a comment why the intentional data race in the quick check is safe or not so safe in a 32bit corner case and why we don't worry about it. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.337366695@linutronix.de
|
#
c398960c |
|
17-Nov-2020 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Document protections for tick related data The protection rules for tick_next_period and last_jiffies_update are blury at best. Clarify this. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20201117132006.197713794@linutronix.de
|
#
bca37119 |
|
26-Jun-2020 |
Paul E. McKenney <paulmck@kernel.org> |
tick-sched: Clarify "NOHZ: local_softirq_pending" warning Currently, can_stop_idle_tick() prints "NOHZ: local_softirq_pending HH" (where "HH" is the hexadecimal softirq vector number) when one or more non-RCU softirq handlers are still enabled when checking to stop the scheduler-tick interrupt. This message is not as enlightening as one might hope, so this commit changes it to "NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #HH". Reported-by: Andy Lutomirski <luto@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
#
3c8920e2 |
|
14-May-2020 |
Frederic Weisbecker <frederic@kernel.org> |
tick/nohz: Narrow down noise while setting current task's tick dependency Setting a tick dependency on any task, including the case where a task sets that dependency on itself, triggers an IPI to all CPUs. That is of course suboptimal but it had previously not been an issue because it was only used by POSIX CPU timers on nohz_full, which apparently never occurs in latency-sensitive workloads in production. (Or users of such systems are suffering in silence on the one hand or venting their ire on the wrong people on the other.) But RCU now sets a task tick dependency on the current task in order to fix stall issues that can occur during RCU callback processing. Thus, RCU callback processing triggers frequent system-wide IPIs from nohz_full CPUs. This is quite counter-productive, after all, avoiding IPIs is what nohz_full is supposed to be all about. This commit therefore optimizes tasks' self-setting of a task tick dependency by using tick_nohz_full_kick() to avoid the system-wide IPI. Instead, only the execution of the one task is disturbed, which is acceptable given that this disturbance is well down into the noise compared to the degree to which the RCU callback processing itself disturbs execution. Fixes: 6a949b7af82d (rcu: Force on tick when invoking lots of callbacks) Reported-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: stable@kernel.org Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
#
49915ac3 |
|
20-Mar-2020 |
Sebastian Andrzej Siewior <bigeasy@linutronix.de> |
lockdep: Annotate irq_work Mark irq_work items with IRQ_WORK_HARD_IRQ which should be invoked in hardirq context even on PREEMPT_RT. IRQ_WORK without this flag will be invoked in softirq context on PREEMPT_RT. Set ->irq_config to 1 for the IRQ_WORK items which are invoked in softirq context so lockdep knows that these can safely acquire a spinlock_t. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20200321113242.643576700@linutronix.de
|
#
e5d4d175 |
|
20-Mar-2020 |
Thomas Gleixner <tglx@linutronix.de> |
timekeeping: Split jiffies seqlock seqlock consists of a sequence counter and a spinlock_t which is used to serialize the writers. spinlock_t is substituted by a "sleeping" spinlock on PREEMPT_RT enabled kernels which breaks the usage in the timekeeping code as the writers are executed in hard interrupt and therefore non-preemptible context even on PREEMPT_RT. The spinlock in seqlock cannot be unconditionally replaced by a raw_spinlock_t as many seqlock users have nesting spinlock sections or other code which is not suitable to run in truly atomic context on RT. Instead of providing a raw_seqlock API for a single use case, open code the seqlock for the jiffies use case and implement it with a raw_spinlock_t and a sequence counter. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20200321113242.120587764@linutronix.de
|
#
de95a991 |
|
04-Dec-2019 |
Eric Dumazet <edumazet@google.com> |
tick/sched: Annotate lockless access to last_jiffies_update syzbot (KCSAN) reported a data-race in tick_do_update_jiffies64(): BUG: KCSAN: data-race in tick_do_update_jiffies64 / tick_do_update_jiffies64 write to 0xffffffff8603d008 of 8 bytes by interrupt on cpu 1: tick_do_update_jiffies64+0x100/0x250 kernel/time/tick-sched.c:73 tick_sched_do_timer+0xd4/0xe0 kernel/time/tick-sched.c:138 tick_sched_timer+0x43/0xe0 kernel/time/tick-sched.c:1292 __run_hrtimer kernel/time/hrtimer.c:1514 [inline] __hrtimer_run_queues+0x274/0x5f0 kernel/time/hrtimer.c:1576 hrtimer_interrupt+0x22a/0x480 kernel/time/hrtimer.c:1638 local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1110 [inline] smp_apic_timer_interrupt+0xdc/0x280 arch/x86/kernel/apic/apic.c:1135 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830 arch_local_irq_restore arch/x86/include/asm/paravirt.h:756 [inline] kcsan_setup_watchpoint+0x1d4/0x460 kernel/kcsan/core.c:436 check_access kernel/kcsan/core.c:466 [inline] __tsan_read1 kernel/kcsan/core.c:593 [inline] __tsan_read1+0xc2/0x100 kernel/kcsan/core.c:593 kallsyms_expand_symbol.constprop.0+0x70/0x160 kernel/kallsyms.c:79 kallsyms_lookup_name+0x7f/0x120 kernel/kallsyms.c:170 insert_report_filterlist kernel/kcsan/debugfs.c:155 [inline] debugfs_write+0x14b/0x2d0 kernel/kcsan/debugfs.c:256 full_proxy_write+0xbd/0x100 fs/debugfs/file.c:225 __vfs_write+0x67/0xc0 fs/read_write.c:494 vfs_write fs/read_write.c:558 [inline] vfs_write+0x18a/0x390 fs/read_write.c:542 ksys_write+0xd5/0x1b0 fs/read_write.c:611 __do_sys_write fs/read_write.c:623 [inline] __se_sys_write fs/read_write.c:620 [inline] __x64_sys_write+0x4c/0x60 fs/read_write.c:620 do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x44/0xa9 read to 0xffffffff8603d008 of 8 bytes by task 0 on cpu 0: tick_do_update_jiffies64+0x2b/0x250 kernel/time/tick-sched.c:62 tick_nohz_update_jiffies kernel/time/tick-sched.c:505 [inline] tick_nohz_irq_enter kernel/time/tick-sched.c:1257 [inline] tick_irq_enter+0x139/0x1c0 kernel/time/tick-sched.c:1274 irq_enter+0x4f/0x60 kernel/softirq.c:354 entering_irq arch/x86/include/asm/apic.h:517 [inline] entering_ack_irq arch/x86/include/asm/apic.h:523 [inline] smp_apic_timer_interrupt+0x55/0x280 arch/x86/kernel/apic/apic.c:1133 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830 native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:60 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:571 default_idle_call+0x1e/0x40 kernel/sched/idle.c:94 cpuidle_idle_call kernel/sched/idle.c:154 [inline] do_idle+0x1af/0x280 kernel/sched/idle.c:263 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:355 rest_init+0xec/0xf6 init/main.c:452 arch_call_rest_init+0x17/0x37 start_kernel+0x838/0x85e init/main.c:786 x86_64_start_reservations+0x29/0x2b arch/x86/kernel/head64.c:490 x86_64_start_kernel+0x72/0x76 arch/x86/kernel/head64.c:471 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc7+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Use READ_ONCE() and WRITE_ONCE() to annotate this expected race. Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20191205045619.204946-1-edumazet@google.com
|
#
e44fcb4b |
|
15-Oct-2019 |
Frederic Weisbecker <frederic@kernel.org> |
sched/vtime: Rename vtime_accounting_cpu_enabled() to vtime_accounting_enabled_this_cpu() Standardize the naming on top of the vtime_accounting_enabled_*() base. Also make it clear we are checking the vtime state of the *current* CPU with this function. We'll need to add an API to check that state on remote CPUs as well, so we must disambiguate the naming. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rjw@rjwysocki.net> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Wanpeng Li <wanpengli@tencent.com> Cc: Yauheni Kaliuta <yauheni.kaliuta@redhat.com> Link: https://lkml.kernel.org/r/20191016025700.31277-9-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
ae9e557b |
|
09-Aug-2019 |
Paul E. McKenney <paulmck@kernel.org> |
time: Export tick start/stop functions for rcutorture It turns out that rcutorture needs to ensure that the scheduling-clock interrupt is enabled in CONFIG_NO_HZ_FULL kernels before starting on CPU-bound in-kernel processing. This commit therefore exports tick_nohz_dep_set_task(), tick_nohz_dep_clear_task(), and tick_nohz_full_setup() to GPL kernel modules. Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
#
01b4c399 |
|
24-Jul-2019 |
Frederic Weisbecker <frederic@kernel.org> |
nohz: Add TICK_DEP_BIT_RCU If a nohz_full CPU is looping in the kernel, the scheduling-clock tick might nevertheless remain disabled. In !PREEMPT kernels, this can prevent RCU's attempts to enlist the aid of that CPU's executions of cond_resched(), which can in turn result in an arbitrarily delayed grace period and thus an OOM. RCU therefore needs a way to enable a holdout nohz_full CPU's scheduler-clock interrupt. This commit therefore provides a new TICK_DEP_BIT_RCU value which RCU can pass to tick_dep_set_cpu() and friends to force on the scheduler-clock interrupt for a specified CPU or task. In some cases, rcutorture needs to turn on the scheduler-clock tick, so this commit also exports the relevant symbols to GPL-licensed modules. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
#
71fed982 |
|
23-Aug-2019 |
Sebastian Andrzej Siewior <bigeasy@linutronix.de> |
tick: Mark sched_timer to expire in hard interrupt context sched_timer must be initialized with the _HARD mode suffix to ensure expiry in hard interrupt context on RT. The previous conversion to HARD expiry mode missed on one instance in tick_nohz_switch_to_nohz(). Fix it up. Fixes: 902a9f9c50905 ("tick: Mark tick related hrtimers to expiry in hard interrupt context") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20190823113845.12125-3-bigeasy@linutronix.de
|
#
902a9f9c |
|
26-Jul-2019 |
Sebastian Andrzej Siewior <bigeasy@linutronix.de> |
tick: Mark tick related hrtimers to expiry in hard interrupt context The tick related hrtimers, which drive the scheduler tick and hrtimer based broadcasting are required to expire in hard interrupt context for obvious reasons. Mark them so PREEMPT_RT kernels wont move them to soft interrupt expiry. Make the horribly formatted RCU_NONIDLE bracket maze readable while at it. No functional change, [ tglx: Split out from larger combo patch. Add changelog ] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20190726185753.459144407@linutronix.de
|
#
5e83eafb |
|
27-May-2019 |
Dietmar Eggemann <dietmar.eggemann@arm.com> |
sched/fair: Remove the rq->cpu_load[] update code With LB_BIAS disabled, there is no need to update the rq->cpu_load[idx] any more. Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rik van Riel <riel@surriel.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Morten Rasmussen <morten.rasmussen@arm.com> Cc: Patrick Bellasi <patrick.bellasi@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Perret <quentin.perret@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Valentin Schneider <valentin.schneider@arm.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20190527062116.11512-2-dietmar.eggemann@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
08ae95f4 |
|
10-Apr-2019 |
Nicholas Piggin <npiggin@gmail.com> |
nohz_full: Allow the boot CPU to be nohz_full Allow the boot CPU/CPU0 to be nohz_full. Have the boot CPU take the do_timer duty during boot until a housekeeping CPU can take over. This is supported when CONFIG_PM_SLEEP_SMP is not configured, or when it is configured and the arch allows suspend on non-zero CPUs. nohz_full has been trialed at a large supercomputer site and found to significantly reduce jitter. In order to deploy it in production, they need CPU0 to be nohz_full because their job control system requires the application CPUs to start from 0, and the housekeeping CPUs are placed higher. An equivalent job scheduling that uses CPU0 for housekeeping could be achieved by modifying their system, but it is preferable if nohz_full can support their environment without modification. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lkml.kernel.org/r/20190411033448.20842-6-npiggin@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
6f9b83ac |
|
27-Mar-2019 |
Ulf Hansson <ulf.hansson@linaro.org> |
cpuidle: Export the next timer expiration for CPUs To be able to predict the sleep duration for a CPU entering idle, it is essential to know the expiration time of the next timer. Both the teo and the menu cpuidle governors already use this information for CPU idle state selection. Moving forward, a similar prediction needs to be made for a group of idle CPUs rather than for a single one and the following changes implement a new genpd governor for that purpose. In order to support that feature, add a new function called tick_nohz_get_next_hrtimer() that will return the next hrtimer expiration time of a given CPU to be invoked after deciding whether or not to stop the scheduler tick on that CPU. Make the cpuidle core call tick_nohz_get_next_hrtimer() right before invoking the ->enter() callback provided by the cpuidle driver for the given state and store its return value in the per-CPU struct cpuidle_device, so as to make it available to code outside of cpuidle. Note that at the point when cpuidle calls tick_nohz_get_next_hrtimer(), the governor's ->select() callback has already returned and indicated whether or not the tick should be stopped, so in fact the value returned by tick_nohz_get_next_hrtimer() always is the next hrtimer expiration time for the given CPU, possibly including the tick (if it hasn't been stopped). Co-developed-by: Lina Iyer <lina.iyer@linaro.org> Co-developed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> [ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
e1e41b6c |
|
18-Mar-2019 |
Rasmus Villemoes <linux@rasmusvillemoes.dk> |
timekeeping: Consistently use unsigned int for seqcount snapshot The timekeeping code uses a random mix of "unsigned long" and "unsigned int" for the seqcount snapshots (ratio 14:12). Since the seqlock.h API is entirely based on unsigned int, use that throughout. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190318195557.20773-1-linux@rasmusvillemoes.dk
|
#
f49c174b |
|
31-Oct-2018 |
Thomas Gleixner <tglx@linutronix.de> |
hrtimers/tick/clockevents: Remove sloppy license references "For licencing details see kernel-base/COPYING" and similar license references have no value over the SPDX identifier. Remove them. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182252.963632760@linutronix.de
|
#
35728b82 |
|
31-Oct-2018 |
Thomas Gleixner <tglx@linutronix.de> |
time: Add SPDX license identifiers Update the time(r) core files files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Philippe Ombredanne, Kate Stewart and myself. The data has been created with two independent license scanners and manual inspection. The following files do not contain any direct license information and have been omitted from the big initial SPDX changes: timeconst.bc: The .bc files were not touched time.c, timer.c, timekeeping.c: Licence was deduced from EXPORT_SYMBOL_GPL As those files do not contain direct license references they fall under the project license, i.e. GPL V2 only. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Link: https://lkml.kernel.org/r/20181031182252.879109557@linutronix.de
|
#
58c5fc2b |
|
31-Oct-2018 |
Thomas Gleixner <tglx@linutronix.de> |
time: Remove useless filenames in top level comments Remove the pointless filenames in the top level comments. They have no value at all and just occupy space. While at it tidy up some of the comments and remove a stale one. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182252.794898238@linutronix.de
|
#
d59e0ba1 |
|
09-Oct-2018 |
Peng Hao <peng.hao2@zte.com.cn> |
tick/sched : Remove redundant cpu_online() check can_stop_idle_tick() checks cpu_online() twice. The first check leaves the function when the CPU is not online, so the second check it redundant. Remove it. Signed-off-by: Peng Hao <peng.hao2@zte.com.cn> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: fweisbec@gmail.com Link: https://lkml.kernel.org/r/1539099815-2943-1-git-send-email-penghao122@sina.com.cn
|
#
80d20d35 |
|
31-Jul-2018 |
Anna-Maria Gleixner <anna-maria@linutronix.de> |
nohz: Fix local_timer_softirq_pending() local_timer_softirq_pending() checks whether the timer softirq is pending with: local_softirq_pending() & TIMER_SOFTIRQ. This is wrong because TIMER_SOFTIRQ is the softirq number and not a bitmask. So the test checks for the wrong bit. Use BIT(TIMER_SOFTIRQ) instead. Fixes: 5d62c183f9e9 ("nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()") Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com> Acked-by: Frederic Weisbecker <frederic@kernel.org> Cc: bigeasy@linutronix.de Cc: peterz@infradead.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180731161358.29472-1-anna-maria@linutronix.de
|
#
a3ed0e43 |
|
25-Apr-2018 |
Thomas Gleixner <tglx@linutronix.de> |
Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME Revert commits 92af4dcb4e1c ("tracing: Unify the "boot" and "mono" tracing clocks") 127bfa5f4342 ("hrtimer: Unify MONOTONIC and BOOTTIME clock behavior") 7250a4047aa6 ("posix-timers: Unify MONOTONIC and BOOTTIME clock behavior") d6c7270e913d ("timekeeping: Remove boot time specific code") f2d6fdbfd238 ("Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior") d6ed449afdb3 ("timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock") 72199320d49d ("timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock") As stated in the pull request for the unification of CLOCK_MONOTONIC and CLOCK_BOOTTIME, it was clear that we might have to revert the change. As reported by several folks systemd and other applications rely on the documented behaviour of CLOCK_MONOTONIC on Linux and break with the above changes. After resume daemons time out and other timeout related issues are observed. Rafael compiled this list: * systemd kills daemons on resume, after >WatchdogSec seconds of suspending (Genki Sky). [Verified that that's because systemd uses CLOCK_MONOTONIC and expects it to not include the suspend time.] * systemd-journald misbehaves after resume: systemd-journald[7266]: File /var/log/journal/016627c3c4784cd4812d4b7e96a34226/system.journal corrupted or uncleanly shut down, renaming and replacing. (Mike Galbraith). * NetworkManager reports "networking disabled" and networking is broken after resume 50% of the time (Pavel). [May be because of systemd.] * MATE desktop dims the display and starts the screensaver right after system resume (Pavel). * Full system hang during resume (me). [May be due to systemd or NM or both.] That happens on debian and open suse systems. It's sad, that these problems were neither catched in -next nor by those folks who expressed interest in this change. Reported-by: Rafael J. Wysocki <rjw@rjwysocki.net> Reported-by: Genki Sky <sky@genki.is>, Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kevin Easton <kevin@guarana.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Salyzyn <salyzyn@android.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org>
|
#
1f71addd |
|
24-Apr-2018 |
Thomas Gleixner <tglx@linutronix.de> |
tick/sched: Do not mess with an enqueued hrtimer Kaike reported that in tests rdma hrtimers occasionaly stopped working. He did great debugging, which provided enough context to decode the problem. CPU 3 CPU 2 idle start sched_timer expires = 712171000000 queue->next = sched_timer start rdmavt timer. expires = 712172915662 lock(baseof(CPU3)) tick_nohz_stop_tick() tick = 716767000000 timerqueue_add(tmr) hrtimer_set_expires(sched_timer, tick); sched_timer->expires = 716767000000 <---- FAIL if (tmr->expires < queue->next->expires) hrtimer_start(sched_timer) queue->next = tmr; lock(baseof(CPU3)) unlock(baseof(CPU3)) timerqueue_remove() timerqueue_add() ts->sched_timer is queued and queue->next is pointing to it, but then ts->sched_timer.expires is modified. This not only corrupts the ordering of the timerqueue RB tree, it also makes CPU2 see the new expiry time of timerqueue->next->expires when checking whether timerqueue->next needs to be updated. So CPU2 sees that the rdma timer is earlier than timerqueue->next and sets the rdma timer as new next. Depending on whether it had also seen the new time at RB tree enqueue, it might have queued the rdma timer at the wrong place and then after removing the sched_timer the RB tree is completely hosed. The problem was introduced with a commit which tried to solve inconsistency between the hrtimer in the tick_sched data and the underlying hardware clockevent. It split out hrtimer_set_expires() to store the new tick time in both the NOHZ and the NOHZ + HIGHRES case, but missed the fact that in the NOHZ + HIGHRES case the hrtimer might still be queued. Use hrtimer_start(timer, tick...) for the NOHZ + HIGHRES case which sets timer->expires after canceling the timer and move the hrtimer_set_expires() invocation into the NOHZ only code path which is not affected as it merily uses the hrtimer as next event storage so code pathes can be shared with the NOHZ + HIGHRES case. Fixes: d4af6d933ccf ("nohz: Fix spurious warning when hrtimer and clockevent get out of sync") Reported-by: "Wan Kaike" <kaike.wan@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Frederic Weisbecker <frederic@kernel.org> Cc: "Marciniszyn Mike" <mike.marciniszyn@intel.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: linux-rdma@vger.kernel.org Cc: "Dalessandro Dennis" <dennis.dalessandro@intel.com> Cc: "Fleck John" <john.fleck@intel.com> Cc: stable@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: "Weiny Ira" <ira.weiny@intel.com> Cc: "linux-rdma@vger.kernel.org" Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1804241637390.1679@nanos.tec.linutronix.de Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1804242119210.1597@nanos.tec.linutronix.de
|
#
bbe9a70a |
|
09-Apr-2018 |
Arnd Bergmann <arnd@arndb.de> |
tick-sched: avoid a maybe-uninitialized warning The use of bitfields seems to confuse gcc, leading to a false-positive warning in all compiler versions: kernel/time/tick-sched.c: In function 'tick_nohz_idle_exit': kernel/time/tick-sched.c:538:2: error: 'now' may be used uninitialized in this function [-Werror=maybe-uninitialized] This introduces a temporary variable to track the flags so gcc doesn't have to evaluate twice, eliminating the code path that leads to the warning. Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=85301 Fixes: 1cae544d42d2 ("nohz: Gather tick_sched booleans under a common flag field") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
ff7de620 |
|
06-Apr-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
nohz: Avoid duplication of code related to got_idle_tick Move the code setting ts->got_idle_tick into tick_sched_do_timer() to avoid code duplication. No intentional changes in functionality. Suggested-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
#
2bc629a6 |
|
05-Apr-2018 |
Frederic Weisbecker <frederic@kernel.org> |
nohz: Gather tick_sched booleans under a common flag field Optimize the space and leave plenty of room for further flags. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> [ rjw: Do not use __this_cpu_read() to access tick_stopped and add got_idle_tick to avoid overloading inidle ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
296bb1e5 |
|
05-Apr-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
cpuidle: menu: Refine idle state selection for running tick If the tick isn't stopped, the target residency of the state selected by the menu governor may be greater than the actual time to the next tick and that means lost energy. To avoid that, make tick_nohz_get_sleep_length() return the current time to the next event (before stopping the tick) in addition to the estimated one via an extra pointer argument and make menu_select() use that value to refine the state selection when necessary. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
#
554c8aa8 |
|
03-Apr-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
sched: idle: Select idle state before stopping the tick In order to address the issue with short idle duration predictions by the idle governor after the scheduler tick has been stopped, reorder the code in cpuidle_idle_call() so that the governor idle state selection runs before tick_nohz_idle_go_idle() and use the "nohz" hint returned by cpuidle_select() to decide whether or not to stop the tick. This isn't straightforward, because menu_select() invokes tick_nohz_get_sleep_length() to get the time to the next timer event and the number returned by the latter comes from __tick_nohz_idle_stop_tick(). Fortunately, however, it is possible to compute that number without actually stopping the tick and with the help of the existing code. Namely, tick_nohz_get_sleep_length() can be made call tick_nohz_next_event(), introduced earlier, to get the time to the next non-highres timer event. If that happens, tick_nohz_next_event() need not be called by __tick_nohz_idle_stop_tick() again. If it turns out that the scheduler tick cannot be stopped going forward or the next timer event is too close for the tick to be stopped, tick_nohz_get_sleep_length() can simply return the time to the next event currently programmed into the corresponding clock event device. In addition to knowing the return value of tick_nohz_next_event(), however, tick_nohz_get_sleep_length() needs to know the time to the next highres timer event, but with the scheduler tick timer excluded, which can be computed with the help of hrtimer_get_next_event(). That minimum of that number and the tick_nohz_next_event() return value is the total time to the next timer event with the assumption that the tick will be stopped. It can be returned to the idle governor which can use it for predicting idle duration (under the assumption that the tick will be stopped) and deciding whether or not it makes sense to stop the tick before putting the CPU into the selected idle state. With the above, the sleep_length field in struct tick_sched is not necessary any more, so drop it. Link: https://bugzilla.kernel.org/show_bug.cgi?id=199227 Reported-by: Doug Smythies <dsmythies@telus.net> Reported-by: Thomas Ilsche <thomas.ilsche@tu-dresden.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
#
23a8d888 |
|
05-Apr-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
time: tick-sched: Split tick_nohz_stop_sched_tick() In order to address the issue with short idle duration predictions by the idle governor after the scheduler tick has been stopped, split tick_nohz_stop_sched_tick() into two separate routines, one computing the time to the next timer event and the other simply stopping the tick when the time to the next timer event is known. Prepare these two routines to be called separately, as one of them will be called by the idle governor in the cpuidle_select() code path after subsequent changes. Update the former callers of tick_nohz_stop_sched_tick() to use the new routines, tick_nohz_next_event() and tick_nohz_stop_tick(), instead of it and move the updates of the sleep_length field in struct tick_sched into __tick_nohz_idle_stop_tick() as it doesn't need to be updated anywhere else. There should be no intentional visible changes in functionality resulting from this change. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
|
#
45f1ff59 |
|
22-Mar-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
cpuidle: Return nohz hint from cpuidle_select() Add a new pointer argument to cpuidle_select() and to the ->select cpuidle governor callback to allow a boolean value indicating whether or not the tick should be stopped before entering the selected state to be returned from there. Make the ladder governor ignore that pointer (to preserve its current behavior) and make the menu governor return 'false" through it if: (1) the idle exit latency is constrained at 0, or (2) the selected state is a polling one, or (3) the expected idle period duration is within the tick period range. In addition to that, the correction factor computations in the menu governor need to take the possibility that the tick may not be stopped into account to avoid artificially small correction factor values. To that end, add a mechanism to record tick wakeups, as suggested by Peter Zijlstra, and use it to modify the menu_update() behavior when tick wakeup occurs. Namely, if the CPU is woken up by the tick and the return value of tick_nohz_get_sleep_length() is not within the tick boundary, the predicted idle duration is likely too short, so make menu_update() try to compensate for that by updating the governor statistics as though the CPU was idle for a long time. Since the value returned through the new argument pointer of cpuidle_select() is not used by its caller yet, this change by itself is not expected to alter the functionality of the code. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
#
2aaf709a |
|
15-Mar-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
sched: idle: Do not stop the tick upfront in the idle loop Push the decision whether or not to stop the tick somewhat deeper into the idle loop. Stopping the tick upfront leads to unpleasant outcomes in case the idle governor doesn't agree with the nohz code on the duration of the upcoming idle period. Specifically, if the tick has been stopped and the idle governor predicts short idle, the situation is bad regardless of whether or not the prediction is accurate. If it is accurate, the tick has been stopped unnecessarily which means excessive overhead. If it is not accurate, the CPU is likely to spend too much time in the (shallow, because short idle has been predicted) idle state selected by the governor [1]. As the first step towards addressing this problem, change the code to make the tick stopping decision inside of the loop in do_idle(). In particular, do not stop the tick in the cpu_idle_poll() code path. Also don't do that in tick_nohz_irq_exit() which doesn't really have enough information on whether or not to stop the tick. Link: https://marc.info/?l=linux-pm&m=150116085925208&w=2 # [1] Link: https://tu-dresden.de/zih/forschung/ressourcen/dateien/projekte/haec/powernightmares.pdf Suggested-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
#
0e776768 |
|
05-Apr-2018 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
time: tick-sched: Reorganize idle tick management code Prepare the scheduler tick code for reworking the idle loop to avoid stopping the tick in some cases. The idea is to split the nohz idle entry call to decouple the idle time stats accounting and preparatory work from the actual tick stop code, in order to later be able to delay the tick stop once we reach more power-knowledgeable callers. Move away the tick_nohz_start_idle() invocation from __tick_nohz_idle_enter(), rename the latter to __tick_nohz_idle_stop_tick() and define tick_nohz_idle_stop_tick() as a wrapper around it for calling it from the outside. Make tick_nohz_idle_enter() only call tick_nohz_start_idle() instead of calling the entire __tick_nohz_idle_enter(), add another wrapper disabling and enabling interrupts around tick_nohz_idle_stop_tick() and make the current callers of tick_nohz_idle_enter() call it too to retain their current functionality. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
|
#
d6ed449a |
|
01-Mar-2018 |
Thomas Gleixner <tglx@linutronix.de> |
timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock The MONOTONIC clock is not fast forwarded by the time spent in suspend on resume. This is only done for the BOOTTIME clock. The reason why the MONOTONIC clock is not forwarded is historical: the original Linux implementation was using jiffies as a base for the MONOTONIC clock and jiffies have never been advanced after resume. At some point when timekeeping was unified in the core code, the MONONOTIC clock was advanced after resume which also advanced jiffies causing interesting side effects. As a consequence the the MONOTONIC clock forwarding was disabled again and the BOOTTIME clock was introduced, which allows to read time since boot. Back then it was not possible to completely distangle the MONOTONIC clock and jiffies because there were still interfaces which exposed the MONOTONIC clock behaviour based on the timer wheel and therefore jiffies. As of today none of the MONOTONIC clock facilities depends on jiffies anymore so the forwarding can be done seperately. This is achieved by forwarding the variables which are used for the jiffies update after resume before the tick is restarted, In timekeeping resume, the change is rather simple. Instead of updating the offset between the MONOTONIC clock and the REALTIME/BOOTTIME clocks, advance the time keeper base for the MONOTONIC and the MONOTONIC_RAW clocks by the time spent in suspend. The MONOTONIC clock is now the same as the BOOTTIME clock and the offset between the REALTIME and the MONOTONIC clocks is the same as before suspend. There might be side effects in applications, which rely on the (unfortunately) well documented behaviour of the MONOTONIC clock, but the downsides of the existing behaviour are probably worse. There is one obvious issue. Up to now it was possible to retrieve the time spent in suspend by observing the delta between the MONOTONIC clock and the BOOTTIME clock. This is not longer available, but the previously introduced mechanism to read the active non-suspended monotonic time can mitigate that in a detectable fashion. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Kevin Easton <kevin@guarana.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Salyzyn <salyzyn@android.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20180301165150.062975504@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
00357f5e |
|
21-Dec-2017 |
Peter Zijlstra <peterz@infradead.org> |
sched/nohz: Clean up nohz enter/exit The primary observation is that nohz enter/exit is always from the current CPU, therefore NOHZ_TICK_STOPPED does not in fact need to be an atomic. Secondary is that we appear to have 2 nearly identical hooks in the nohz enter code, set_cpu_sd_state_idle() and nohz_balance_enter_idle(). Fold the whole set_cpu_sd_state thing into nohz_balance_{enter,exit}_idle. Removes an atomic op from both enter and exit paths. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
dcdedb24 |
|
20-Feb-2018 |
Frederic Weisbecker <frederic@kernel.org> |
sched/nohz: Remove the 1 Hz tick code Now that the 1Hz tick is offloaded to workqueues, we can safely remove the residual code that used to handle it locally. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1519186649-3242-7-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
22ab8bc0 |
|
20-Feb-2018 |
Frederic Weisbecker <frederic@kernel.org> |
nohz: Allow to check if remote CPU tick is stopped This check is racy but provides a good heuristic to determine whether a CPU may need a remote tick or not. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1519186649-3242-4-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
a3642983 |
|
20-Feb-2018 |
Frederic Weisbecker <frederic@kernel.org> |
nohz: Convert tick_nohz_tick_stopped() to bool It makes this function more self-explanatory about what it does and how to use it. Reported-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1519186649-3242-3-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
a7c8655b |
|
30-Nov-2017 |
Paul E. McKenney <paulmck@kernel.org> |
sched/isolation: Eliminate NO_HZ_FULL_ALL Commit 6f1982fedd59 ("sched/isolation: Handle the nohz_full= parameter") broke CONFIG_NO_HZ_FULL_ALL=y kernels. This breakage is due to the code under CONFIG_NO_HZ_FULL_ALL failing to invoke the shiny new housekeeping functions. This means that rcutorture scenario TREE04 now emits RCU CPU stall warnings due to the RCU grace-period kthreads not being awakened at a time of their choosing, or perhaps even not at all: [ 27.731422] rcu_bh kthread starved for 21001 jiffies! g18446744073709551369 c18446744073709551368 f0x0 RCU_GP_WAIT_FQS(3) ->state=0x402 ->cpu=3 [ 27.731423] rcu_bh I14936 9 2 0x80080000 [ 27.731435] Call Trace: [ 27.731440] __schedule+0x31a/0x6d0 [ 27.731442] schedule+0x31/0x80 [ 27.731446] schedule_timeout+0x15a/0x320 [ 27.731453] ? call_timer_fn+0x130/0x130 [ 27.731457] rcu_gp_kthread+0x66c/0xea0 [ 27.731458] ? rcu_gp_kthread+0x66c/0xea0 Because no one has complained about CONFIG_NO_HZ_FULL_ALL=y being broken, I hypothesize that no one is in fact using it, other than rcutorture. This commit therefore eliminates CONFIG_NO_HZ_FULL_ALL and updates rcutorture's config files to instead use the nohz_full= kernel parameter to put the desired CPUs into nohz_full mode. Fixes: 6f1982fedd59 ("sched/isolation: Handle the nohz_full= parameter") Reported-by: kernel test robot <xiaolong.ye@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Jonathan Corbet <corbet@lwn.net>
|
#
ae67bada |
|
14-Jan-2018 |
Thomas Gleixner <tglx@linutronix.de> |
hrtimer: Optimize the hrtimer code by using static keys for migration_enable/nohz_active The hrtimer_cpu_base::migration_enable and ::nohz_active fields were originally introduced to avoid accessing global variables for these decisions. Still that results in a (cache hot) load and conditional branch, which can be avoided by using static keys. Implement it with static keys and optimize for the most critical case of high performance networking which tends to disable the timer migration functionality. No change in functionality. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: keescook@chromium.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1801142327490.2371@nanos Link: https://lkml.kernel.org/r/20171221104205.7269-2-anna-maria@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
5d62c183 |
|
22-Dec-2017 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick() The conditions in irq_exit() to invoke tick_nohz_irq_exit() which subsequently invokes tick_nohz_stop_sched_tick() are: if ((idle_cpu(cpu) && !need_resched()) || tick_nohz_full_cpu(cpu)) If need_resched() is not set, but a timer softirq is pending then this is an indication that the softirq code punted and delegated the execution to softirqd. need_resched() is not true because the current interrupted task takes precedence over softirqd. Invoking tick_nohz_irq_exit() in this case can cause an endless loop of timer interrupts because the timer wheel contains an expired timer, but softirqs are not yet executed. So it returns an immediate expiry request, which causes the timer to fire immediately again. Lather, rinse and repeat.... Prevent that by adding a check for a pending timer soft interrupt to the conditions in tick_nohz_stop_sched_tick() which avoid calling get_next_timer_interrupt(). That keeps the tick sched timer on the tick and prevents a repetitive programming of an already expired timer. Reported-by: Sebastian Siewior <bigeasy@linutronix.d> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul McKenney <paulmck@linux.vnet.ibm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272156050.2431@nanos
|
#
466a2b42 |
|
20-Dec-2017 |
Joel Fernandes <joelaf@google.com> |
cpufreq: schedutil: Use idle_calls counter of the remote CPU Since the recent remote cpufreq callback work, its possible that a cpufreq update is triggered from a remote CPU. For single policies however, the current code uses the local CPU when trying to determine if the remote sg_cpu entered idle or is busy. This is incorrect. To remedy this, compare with the nohz tick idle_calls counter of the remote CPU. Fixes: 674e75411fc2 (sched: cpufreq: Allow remote cpufreq callbacks) Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Joel Fernandes <joelaf@google.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
ebf3adba |
|
06-Nov-2017 |
Frederic Weisbecker <frederic@kernel.org> |
timers/nohz: Use lockdep to assert IRQs are disabled/enabled Use lockdep to check that IRQs are enabled or disabled as expected. This way the sanity check only shows overhead when concurrency correctness debug code is enabled. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: David S . Miller <davem@davemloft.net> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tejun Heo <tj@kernel.org> Link: http://lkml.kernel.org/r/1509980490-4285-5-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
6f1982fe |
|
26-Oct-2017 |
Frederic Weisbecker <frederic@kernel.org> |
sched/isolation: Handle the nohz_full= parameter We want to centralize the isolation management, done by the housekeeping subsystem. Therefore we need to handle the nohz_full= parameter from there. Since nohz_full= so far has involved unbound timers, watchdog, RCU and tilegx NAPI isolation, we keep that default behaviour. nohz_full= will be deprecated in the future. We want to control the isolation features from the isolcpus= parameter. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1509072159-31808-10-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
78634061 |
|
26-Oct-2017 |
Frederic Weisbecker <frederic@kernel.org> |
sched/isolation: Move housekeeping related code to its own file The housekeeping code is currently tied to the NOHZ code. As we are planning to make housekeeping independent from it, start with moving the relevant code to its own file. Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Link: http://lkml.kernel.org/r/1509072159-31808-2-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
62cb1188 |
|
29-Aug-2017 |
Peter Zijlstra <peterz@infradead.org> |
sched/idle: Move quiet_vmstate() into the NOHZ code quiet_vmstat() is an expensive function that only makes sense when we go into NOHZ. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: aubrey.li@linux.intel.com Cc: cl@linux.com Cc: fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
a0db971e |
|
18-Jun-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Move idle balancer registration to the idle path The idle load balancing registration path assumes that we only stop the tick when the CPU is idle, ignoring the nohz full case. As a result, a nohz full CPU that is running a task may be chosen to perform idle load balancing. Lets make sure that only CPUs in dynticks idle mode can be picked as idle load balancers. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1497838322-10913-3-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
3c85d6db |
|
18-Jun-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched/loadavg: Generalize "_idle" naming to "_nohz" The loadavg naming code still assumes that nohz == idle whereas its code is actually handling well both nohz idle and nohz full. So lets fix the naming according to what the code actually does, to unconfuse the reader. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1497838322-10913-2-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
d4af6d93 |
|
12-Jun-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Fix spurious warning when hrtimer and clockevent get out of sync The sanity check ensuring that the tick expiry cache (ts->next_tick) is actually in sync with the hardware clock (dev->next_event) makes the wrong assumption that the clock can't be programmed later than the hrtimer deadline. In fact the clock hardware can be programmed later on some conditions such as: * The hrtimer deadline is already in the past. * The hrtimer deadline is earlier than the minimum delay supported by the hardware. Such conditions can be met when we program the tick, for example if the last jiffies update hasn't been seen by the current CPU yet, we may program the hrtimer to a deadline that is earlier than ktime_get() because last_jiffies_update is our timestamp base to compute the next tick. As a result, we can randomly observe such warning: WARNING: CPU: 5 PID: 0 at kernel/time/tick-sched.c:794 tick_nohz_stop_sched_tick kernel/time/tick-sched.c:791 [inline] Call Trace: tick_nohz_irq_exit tick_irq_exit irq_exit exiting_irq smp_call_function_interrupt smp_call_function_single_interrupt call_function_single_interrupt Therefore, let's rather make sure that the tick expiry cache is sync'ed with the tick hrtimer deadline, against which it is not supposed to drift away. The clock hardware instead has its own will and can't be used as a reliable comparison point. Reported-and-tested-by: Sasha Levin <alexander.levin@verizon.com> Reported-and-tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: James Hartsock <hartsjc@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tim Wright <tim@binbash.co.uk> Link: http://lkml.kernel.org/r/1497326654-14122-1-git-send-email-fweisbec@gmail.com [ Minor readability edit. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
f99973e1 |
|
01-Jun-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Fix buggy tick delay on IRQ storms When the tick is stopped and we reach the dynticks evaluation code on IRQ exit, we perform a soft tick restart if we observe an expired timer from there. It means we program the nearest possible tick but we stay in dynticks mode (ts->tick_stopped = 1) because we may need to stop the tick again after that expired timer is handled. Now this solution works most of the time but if we suffer an IRQ storm and those interrupts trigger faster than the hardware clockevents min delay, our tick won't fire until that IRQ storm is finished. Here is the problem: on IRQ exit we reprog the timer to at least NOW() + min_clockevents_delay. Another IRQ fires before the tick so we reschedule again to NOW() + min_clockevents_delay, etc... The tick is eternally rescheduled min_clockevents_delay ahead. A solution is to simply remove this soft tick restart. After all the normal dynticks evaluation path can handle 0 delay just fine. And by doing that we benefit from the optimization branch which avoids clock reprogramming if the clockevents deadline hasn't changed since the last reprog. This fixes our issue because we don't do repetitive clock reprog that always add hardware min delay. As a side effect it should even optimize the 0 delay path in general. Reported-and-tested-by: Octavian Purdila <octavian.purdila@nxp.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1496328429-13317-1-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
7c259045 |
|
15-May-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Reset next_tick cache even when the timer has no regs Handle tick interrupts whose regs are NULL, out of general paranoia. It happens when hrtimer_interrupt() is called from non-interrupt contexts, such as hotplug CPU down events. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
411fe24e |
|
21-Apr-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Fix collision between tick and other hrtimers, again This restores commit: 24b91e360ef5: ("nohz: Fix collision between tick and other hrtimers") ... which got reverted by commit: 558e8e27e73f: ('Revert "nohz: Fix collision between tick and other hrtimers"') ... due to a regression where CPUs spuriously stopped ticking. The bug happened when a tick fired too early past its expected expiration: on IRQ exit the tick was scheduled again to the same deadline but skipped reprogramming because ts->next_tick still kept in cache the deadline. This has been fixed now with resetting ts->next_tick from the tick itself. Extra care has also been taken to prevent from obsolete values throughout CPU hotplug operations. When the tick is stopped and an interrupt occurs afterward, we check on that interrupt exit if the next tick needs to be rescheduled. If it doesn't need any update, we don't want to do anything. In order to check if the tick needs an update, we compare it against the clockevent device deadline. Now that's a problem because the clockevent device is at a lower level than the tick itself if it is implemented on top of hrtimer. Every hrtimer share this clockevent device. So comparing the next tick deadline against the clockevent device deadline is wrong because the device may be programmed for another hrtimer whose deadline collides with the tick. As a result we may end up not reprogramming the tick accidentally. In a worst case scenario under full dynticks mode, the tick stops firing as it is supposed to every 1hz, leaving /proc/stat stalled: Task in a full dynticks CPU ---------------------------- * hrtimer A is queued 2 seconds ahead * the tick is stopped, scheduled 1 second ahead * tick fires 1 second later * on tick exit, nohz schedules the tick 1 second ahead but sees the clockevent device is already programmed to that deadline, fooled by hrtimer A, the tick isn't rescheduled. * hrtimer A is cancelled before its deadline * tick never fires again until an interrupt happens... In order to fix this, store the next tick deadline to the tick_sched local structure and reuse that value later to check whether we need to reprogram the clock after an interrupt. On the other hand, ts->sleep_length still wants to know about the next clock event and not just the tick, so we want to improve the related comment to avoid confusion. Reported-and-tested-by: Tim Wright <tim@binbash.co.uk> Reported-and-tested-by: Pavel Machek <pavel@ucw.cz> Reported-by: James Hartsock <hartsjc@redhat.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1492783255-5051-2-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
ce6cf9a1 |
|
11-May-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Add hrtimer sanity check Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
ac1e843f |
|
20-Apr-2017 |
Peter Zijlstra <peterz@infradead.org> |
sched/clock: Remove unused argument to sched_clock_idle_wakeup_event() The argument to sched_clock_idle_wakeup_event() has not been used in a long time. Remove it. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
b7eaf1aa |
|
21-Mar-2017 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
cpufreq: schedutil: Avoid reducing frequency of busy CPUs prematurely The way the schedutil governor uses the PELT metric causes it to underestimate the CPU utilization in some cases. That can be easily demonstrated by running kernel compilation on a Sandy Bridge Intel processor, running turbostat in parallel with it and looking at the values written to the MSR_IA32_PERF_CTL register. Namely, the expected result would be that when all CPUs were 100% busy, all of them would be requested to run in the maximum P-state, but observation shows that this clearly isn't the case. The CPUs run in the maximum P-state for a while and then are requested to run slower and go back to the maximum P-state after a while again. That causes the actual frequency of the processor to visibly oscillate below the sustainable maximum in a jittery fashion which clearly is not desirable. That has been attributed to CPU utilization metric updates on task migration that cause the total utilization value for the CPU to be reduced by the utilization of the migrated task. If that happens, the schedutil governor may see a CPU utilization reduction and will attempt to reduce the CPU frequency accordingly right away. That may be premature, though, for example if the system is generally busy and there are other runnable tasks waiting to be run on that CPU already. This is unlikely to be an issue on systems where cpufreq policies are shared between multiple CPUs, because in those cases the policy utilization is computed as the maximum of the CPU utilization values over the whole policy and if that turns out to be low, reducing the frequency for the policy most likely is a good idea anyway. On systems with one CPU per policy, however, it may affect performance adversely and even lead to increased energy consumption in some cases. On those systems it may be addressed by taking another utilization metric into consideration, like whether or not the CPU whose frequency is about to be reduced has been idle recently, because if that's not the case, the CPU is likely to be busy in the near future and its frequency should not be reduced. To that end, use the counter of idle calls in the timekeeping code. Namely, make the schedutil governor look at that counter for the current CPU every time before its frequency is about to be reduced. If the counter has not changed since the previous iteration of the governor computations for that CPU, the CPU has been busy for all that time and its frequency should not be decreased, so if the new frequency would be lower than the one set previously, the governor will skip the frequency update. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Joel Fernandes <joelaf@google.com>
|
#
370c9135 |
|
08-Feb-2017 |
Ingo Molnar <mingo@kernel.org> |
sched/headers: Prepare for new header dependencies before moving code to <linux/sched/nohz.h> We are going to split <linux/sched/nohz.h> out of <linux/sched.h>, which will have to be picked up from other headers and a couple of .c files. Create a trivial placeholder <linux/sched/nohz.h> file that just maps to <linux/sched.h> to make this patch obviously correct and bisectable. Include the new header in the files that are going to need it. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
03441a34 |
|
08-Feb-2017 |
Ingo Molnar <mingo@kernel.org> |
sched/headers: Prepare for new header dependencies before moving code to <linux/sched/stat.h> We are going to split <linux/sched/stat.h> out of <linux/sched.h>, which will have to be picked up from other headers and a couple of .c files. Create a trivial placeholder <linux/sched/stat.h> file that just maps to <linux/sched.h> to make this patch obviously correct and bisectable. Include the new header in the files that are going to need it. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
38b8d208 |
|
08-Feb-2017 |
Ingo Molnar <mingo@kernel.org> |
sched/headers: Prepare for new header dependencies before moving code to <linux/sched/nmi.h> We are going to move softlockup APIs out of <linux/sched.h>, which will have to be picked up from other headers and a couple of .c files. <linux/nmi.h> already includes <linux/sched.h>. Include the <linux/nmi.h> header in the files that are going to need it. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
3f07c014 |
|
08-Feb-2017 |
Ingo Molnar <mingo@kernel.org> |
sched/headers: Prepare for new header dependencies before moving code to <linux/sched/signal.h> We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which will have to be picked up from other headers and a couple of .c files. Create a trivial placeholder <linux/sched/signal.h> file that just maps to <linux/sched.h> to make this patch obviously correct and bisectable. Include the new header in the files that are going to need it. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
e6017571 |
|
01-Feb-2017 |
Ingo Molnar <mingo@kernel.org> |
sched/headers: Prepare for new header dependencies before moving code to <linux/sched/clock.h> We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which will have to be picked up from other headers and .c files. Create a trivial placeholder <linux/sched/clock.h> file that just maps to <linux/sched.h> to make this patch obviously correct and bisectable. Include the new header in the files that are going to need it. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
558e8e27 |
|
16-Feb-2017 |
Linus Torvalds <torvalds@linux-foundation.org> |
Revert "nohz: Fix collision between tick and other hrtimers" This reverts commit 24b91e360ef521a2808771633d76ebc68bd5604b and commit 7bdb59f1ad47 ("tick/nohz: Fix possible missing clock reprog after tick soft restart") that depends on it, Pavel reports that it causes occasional boot hangs for him that seem to depend on just how the machine was booted. In particular, his machine hangs at around the PCI fixups of the EHCI USB host controller, but only hangs from cold boot, not from a warm boot. Thomas Gleixner suspecs it's a CPU hotplug interaction, particularly since Pavel also saw suspend/resume issues that seem to be related. We're reverting for now while trying to figure out the root cause. Reported-bisected-and-tested-by: Pavel Machek <pavel@ucw.cz> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org # reverted commits were marked for stable Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
7bdb59f1 |
|
07-Feb-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
tick/nohz: Fix possible missing clock reprog after tick soft restart ts->next_tick keeps track of the next tick deadline in order to optimize clock programmation on irq exit and avoid redundant clock device writes. Now if ts->next_tick missed an update, we may spuriously miss a clock reprog later as the nohz code is fooled by an obsolete next_tick value. This is what happens here on a specific path: when we observe an expired timer from the nohz update code on irq exit, we perform a soft tick restart which simply fires the closest possible tick without actually exiting the nohz mode and restoring a periodic state. But we forget to update ts->next_tick accordingly. As a result, after the next tick resulting from such soft tick restart, the nohz code sees a stale value on ts->next_tick which doesn't match the clock deadline that just expired. If that obsolete ts->next_tick value happens to collide with the actual next tick deadline to be scheduled, we may spuriously bypass the clock reprogramming. In the worst case, the tick may never fire again. Fix this with a ts->next_tick reset on soft tick restart. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Reviewed: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1486485894-29173-1-git-send-email-fweisbec@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
24b91e36 |
|
04-Jan-2017 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Fix collision between tick and other hrtimers When the tick is stopped and an interrupt occurs afterward, we check on that interrupt exit if the next tick needs to be rescheduled. If it doesn't need any update, we don't want to do anything. In order to check if the tick needs an update, we compare it against the clockevent device deadline. Now that's a problem because the clockevent device is at a lower level than the tick itself if it is implemented on top of hrtimer. Every hrtimer share this clockevent device. So comparing the next tick deadline against the clockevent device deadline is wrong because the device may be programmed for another hrtimer whose deadline collides with the tick. As a result we may end up not reprogramming the tick accidentally. In a worst case scenario under full dynticks mode, the tick stops firing as it is supposed to every 1hz, leaving /proc/stat stalled: Task in a full dynticks CPU ---------------------------- * hrtimer A is queued 2 seconds ahead * the tick is stopped, scheduled 1 second ahead * tick fires 1 second later * on tick exit, nohz schedules the tick 1 second ahead but sees the clockevent device is already programmed to that deadline, fooled by hrtimer A, the tick isn't rescheduled. * hrtimer A is cancelled before its deadline * tick never fires again until an interrupt happens... In order to fix this, store the next tick deadline to the tick_sched local structure and reuse that value later to check whether we need to reprogram the clock after an interrupt. On the other hand, ts->sleep_length still wants to know about the next clock event and not just the tick, so we want to improve the related comment to avoid confusion. Reported-by: James Hartsock <hartsjc@redhat.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Rik van Riel <riel@redhat.com> Link: http://lkml.kernel.org/r/1483539124-5693-1-git-send-email-fweisbec@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
2456e855 |
|
25-Dec-2016 |
Thomas Gleixner <tglx@linutronix.de> |
ktime: Get rid of the union ktime is a union because the initial implementation stored the time in scalar nanoseconds on 64 bit machine and in a endianess optimized timespec variant for 32bit machines. The Y2038 cleanup removed the timespec variant and switched everything to scalar nanoseconds. The union remained, but become completely pointless. Get rid of the union and just keep ktime_t as simple typedef of type s64. The conversion was done with coccinelle and some manual mopping up. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
|
#
31eff243 |
|
17-Nov-2016 |
Sebastian Andrzej Siewior <bigeasy@linutronix.de> |
sched/nohz: Convert to hotplug state machine Install the callbacks via the state machine. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: rt@linuxtronix.de Link: http://lkml.kernel.org/r/20161117183541.8588-14-bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
57ccdf44 |
|
07-Sep-2016 |
Wanpeng Li <wanpeng.li@hotmail.com> |
tick/nohz: Prevent stopping the tick on an offline CPU can_stop_full_tick() has no check for offline cpus. So it allows to stop the tick on an offline cpu from the interrupt return path, which is wrong and subsequently makes irq_work_needs_cpu() warn about being called for an offline cpu. Commit f7ea0fd639c2c4 ("tick: Don't invoke tick_nohz_stop_sched_tick() if the cpu is offline") added prevention for can_stop_idle_tick(), but forgot to do the same in can_stop_full_tick(). Add it. [ tglx: Massaged changelog ] Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Link: http://lkml.kernel.org/r/1473245473-4463-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
08d07259 |
|
02-Sep-2016 |
Wanpeng Li <wanpeng.li@hotmail.com> |
tick/nohz: Fix softlockup on scheduler stalls in kvm guest tick_nohz_start_idle() is prevented to be called if the idle tick can't be stopped since commit 1f3b0f8243cb934 ("tick/nohz: Optimize nohz idle enter"). As a result, after suspend/resume the host machine, full dynticks kvm guest will softlockup: NMI watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [swapper/0:0] Call Trace: default_idle+0x31/0x1a0 arch_cpu_idle+0xf/0x20 default_idle_call+0x2a/0x50 cpu_startup_entry+0x39b/0x4d0 rest_init+0x138/0x140 ? rest_init+0x5/0x140 start_kernel+0x4c1/0x4ce ? set_init_arg+0x55/0x55 ? early_idt_handler_array+0x120/0x120 x86_64_start_reservations+0x24/0x26 x86_64_start_kernel+0x142/0x14f In addition, cat /proc/stat | grep cpu in guest or host: cpu 398 16 5049 15754 5490 0 1 46 0 0 cpu0 206 5 450 0 0 0 1 14 0 0 cpu1 81 0 3937 3149 1514 0 0 9 0 0 cpu2 45 6 332 6052 2243 0 0 11 0 0 cpu3 65 2 328 6552 1732 0 0 11 0 0 The idle and iowait states are weird 0 for cpu0(housekeeping). The bug is present in both guest and host kernels, and they both have cpu0's idle and iowait states issue, however, host kernel's suspend/resume path etc will touch watchdog to avoid the softlockup. - The watchdog will not be touched in tick_nohz_stop_idle path (need be touched since the scheduler stall is expected) if idle_active flags are not detected. - The idle and iowait states will not be accounted when exit idle loop (resched or interrupt) if idle start time and idle_active flags are not set. This patch fixes it by reverting commit 1f3b0f8243cb934 since can't stop idle tick doesn't mean can't be idle. Fixes: 1f3b0f8243cb934 ("tick/nohz: Optimize nohz idle enter") Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Sanjeev Yadav<sanjeev.yadav@spreadtrum.com> Cc: Gaurav Jindal<gaurav.jindal@spreadtrum.com> Cc: stable@vger.kernel.org Cc: kvm@vger.kernel.org Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: http://lkml.kernel.org/r/1472798303-4154-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
1f3b0f82 |
|
13-Jul-2016 |
Gaurav Jindal <Gaurav.Jindal@spreadtrum.com> |
tick/nohz: Optimize nohz idle enter tick_nohz_start_idle is called before checking whether the idle tick can be stopped. If the tick cannot be stopped, calling tick_nohz_start_idle() is pointless and just wasting CPU cycles. Only invoke tick_nohz_start_idle() when can_stop_idle_tick() returns true. A short one minute observation of the effect on ARM64 shows a reduction of calls by 1.5% thus optimizing the idle entry sequence. [tglx: Massaged changelog ] Co-developed-by: Sanjeev Yadav<sanjeev.yadav@spreadtrum.com> Signed-off-by: Gaurav Jindal<gaurav.jindal@spreadtrum.com> Link: http://lkml.kernel.org/r/20160714120416.GB21099@gaurav.jindal@spreadtrum.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
a683f390 |
|
04-Jul-2016 |
Thomas Gleixner <tglx@linutronix.de> |
timers: Forward the wheel clock whenever possible The wheel clock is stale when a CPU goes into a long idle sleep. This has the side effect that timers which are queued end up in the outer wheel levels. That results in coarser granularity. To solve this, we keep track of the idle state and forward the wheel clock whenever possible. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Chris Mason <clm@fb.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: George Spelvin <linux@sciencehorizons.net> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Len Brown <lenb@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160704094342.512039360@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
ff006732 |
|
04-Jul-2016 |
Thomas Gleixner <tglx@linutronix.de> |
timers/nohz: Remove pointless tick_nohz_kick_tick() function This was a failed attempt to optimize the timer expiry in idle, which was disabled and never revisited. Remove the cruft. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Chris Mason <clm@fb.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: George Spelvin <linux@sciencehorizons.net> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Len Brown <lenb@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160704094342.431073782@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
0de7611a |
|
30-Jun-2016 |
Ingo Molnar <mingo@kernel.org> |
timers/nohz: Capitalize 'CPU' consistently While reviewing another patch I noticed that kernel/time/tick-sched.c had a charmingly (confusingly, annoyingly) rich set of variants for spelling 'CPU': cpu cpus CPU CPUs per CPU per-CPU per cpu ... sometimes these were mixed even within the same comment block! Compress these variants down to a single consistent set of: CPU CPUs per-CPU Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
6168f8ed |
|
28-Jun-2016 |
Wei Jiangang <weijg.fnst@cn.fujitsu.com> |
timers/nohz: Fix several typos Signed-off-by: Wei Jiangang <weijg.fnst@cn.fujitsu.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: fenghua.yu@intel.com Link: http://lkml.kernel.org/r/1467175910-2966-2-git-send-email-weijg.fnst@cn.fujitsu.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
a1cc5bcf |
|
21-Apr-2016 |
Peter Zijlstra <peterz@infradead.org> |
locking/atomics: Flip atomic_fetch_or() arguments All the atomic operations have their arguments the wrong way around; make atomic_fetch_or() consistent and flip them. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
1f41906a |
|
13-Apr-2016 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched/fair: Correctly handle nohz ticks CPU load accounting Ticks can happen while the CPU is in dynticks-idle or dynticks-singletask mode. In fact "nohz" or "dynticks" only mean that we exit the periodic mode and we try to minimize the ticks as much as possible. The nohz subsystem uses a confusing terminology with the internal state "ts->tick_stopped" which is also available through its public interface with tick_nohz_tick_stopped(). This is a misnomer as the tick is instead reduced with the best effort rather than stopped. In the best case the tick can indeed be actually stopped but there is no guarantee about that. If a timer needs to fire one second later, a tick will fire while the CPU is in nohz mode and this is a very common scenario. Now this confusion happens to be a problem with CPU load updates: cpu_load_update_active() doesn't handle nohz ticks correctly because it assumes that ticks are completely stopped in nohz mode and that cpu_load_update_active() can't be called in dynticks mode. When that happens, the whole previous tickless load is ignored and the function just records the load for the current tick, ignoring potentially long idle periods behind. In order to solve this, we could account the current load for the previous nohz time but there is a risk that we account the load of a task that got freshly enqueued for the whole nohz period. So instead, lets record the dynticks load on nohz frame entry so we know what to record in case of nohz ticks, then use this record to account the tickless load on nohz ticks and nohz frame end. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Byungchul Park <byungchul.park@lge.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1460555812-25375-3-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
cee1afce |
|
13-Apr-2016 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched/fair: Gather CPU load functions under a more conventional namespace The CPU load update related functions have a weak naming convention currently, starting with update_cpu_load_*() which isn't ideal as "update" is a very generic concept. Since two of these functions are public already (and a third is to come) that's enough to introduce a more conventional naming scheme. So let's do the following rename instead: update_cpu_load_*() -> cpu_load_update_*() Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Byungchul Park <byungchul.park@lge.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1460555812-25375-2-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
f009a7a7 |
|
24-Mar-2016 |
Frederic Weisbecker <fweisbec@gmail.com> |
timers/nohz: Convert tick dependency mask to atomic_t The tick dependency mask was intially unsigned long because this is the type on which clear_bit() operates on and fetch_or() accepts it. But now that we have atomic_fetch_or(), we can instead use atomic_andnot() to clear the bit. This consolidates the type of our tick dependency mask, reduce its size on structures and benefit from possible architecture optimizations on atomic_t operations. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1458830281-4255-3-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
a395d6a7 |
|
22-Mar-2016 |
Joe Perches <joe@perches.com> |
kernel/...: convert pr_warning to pr_warn Use the more common logging method with the eventual goal of removing pr_warning altogether. Miscellanea: - Realign arguments - Coalesce formats - Add missing space between a few coalesced formats Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [kernel/power/suspend.c] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
4cc7ecb7 |
|
17-Mar-2016 |
Kees Cook <keescook@chromium.org> |
param: convert some "on"/"off" users to strtobool This changes several users of manual "on"/"off" parsing to use strtobool. Some side-effects: - these uses will now parse y/n/1/0 meaningfully too - the early_param uses will now bubble up parse errors Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Amitkumar Karwar <akarwar@marvell.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Joe Perches <joe@perches.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Nishant Sarmukadam <nishants@marvell.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Steve French <sfrench@samba.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
4f49b90a |
|
22-Jul-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched-clock: Migrate to use new tick dependency mask model Instead of checking sched_clock_stable from the nohz subsystem to verify its tick dependency, migrate it to the new mask in order to include it to the all-in-one check. Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
b7878300 |
|
17-Jul-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
posix-cpu-timers: Migrate to use new tick dependency mask model Instead of providing asynchronous checks for the nohz subsystem to verify posix cpu timers tick dependency, migrate the latter to the new mask. In order to keep track of the running timers and expose the tick dependency accordingly, we must probe the timers queuing and dequeuing on threads and process lists. Unfortunately it implies both task and signal level dependencies. We should be able to further optimize this and merge all that on the task level dependency, at the cost of a bit of complexity and may be overhead. Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
76d92ac3 |
|
17-Jul-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched: Migrate sched to use new tick dependency mask model Instead of providing asynchronous checks for the nohz subsystem to verify sched tick dependency, migrate sched to the new mask. Everytime a task is enqueued or dequeued, we evaluate the state of the tick dependency on top of the policy of the tasks in the runqueue, by order of priority: SCHED_DEADLINE: Need the tick in order to periodically check for runtime SCHED_FIFO : Don't need the tick (no round-robin) SCHED_RR : Need the tick if more than 1 task of the same priority for round robin (simplified with checking if more than one SCHED_RR task no matter what priority). SCHED_NORMAL : Need the tick if more than 1 task for round-robin. We could optimize that further with one flag per sched policy on the tick dependency mask and perform only the checks relevant to the policy concerned by an enqueue/dequeue operation. Since the checks aren't based on the current task anymore, we could get rid of the task switch hook but it's still needed for posix cpu timers. Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
555e0c1e |
|
16-Jul-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
perf: Migrate perf to use new tick dependency mask model Instead of providing asynchronous checks for the nohz subsystem to verify perf event tick dependency, migrate perf to the new mask. Perf needs the tick for two situations: 1) Freq events. We could set the tick dependency when those are installed on a CPU context. But setting a global dependency on top of the global freq events accounting is much easier. If people want that to be optimized, we can still refine that on the per-CPU tick dependency level. This patch dooesn't change the current behaviour anyway. 2) Throttled events: this is a per-cpu dependency. Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
e6e6cc22 |
|
10-Dec-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Use enum code for tick stop failure tracing message It makes nohz tracing more lightweight, standard and easier to parse. Examples: user_loop-2904 [007] d..1 517.701126: tick_stop: success=1 dependency=NONE user_loop-2904 [007] dn.1 518.021181: tick_stop: success=0 dependency=SCHED posix_timers-6142 [007] d..1 1739.027400: tick_stop: success=0 dependency=POSIX_TIMER user_loop-5463 [007] dN.1 1185.931939: tick_stop: success=0 dependency=PERF_EVENTS Suggested-by: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
d027d45d |
|
07-Jun-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: New tick dependency mask The tick dependency is evaluated on every IRQ and context switch. This consists is a batch of checks which determine whether it is safe to stop the tick or not. These checks are often split in many details: posix cpu timers, scheduler, sched clock, perf events.... each of which are made of smaller details: posix cpu timer involves checking process wide timers then thread wide timers. Perf involves checking freq events then more per cpu details. Checking these informations asynchronously every time we update the full dynticks state bring avoidable overhead and a messy layout. Let's introduce instead tick dependency masks: one for system wide dependency (unstable sched clock, freq based perf events), one for CPU wide dependency (sched, throttling perf events), and task/signal level dependencies (posix cpu timers). The subsystems are responsible for setting and clearing their dependency through a set of APIs that will take care of concurrent dependency mask modifications and kick targets to restart the relevant CPU tick whenever needed. This new dependency engine stays beside the old one until all subsystems having a tick dependency are converted to it. Suggested-by: Thomas Gleixner <tglx@linutronix.de> Suggested-by: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
8537bb95 |
|
07-Dec-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Implement wide kick on top of irq work It simplifies it and allows wide kick to be performed, even when IRQs are disabled, without an asynchronous level in the middle. This comes at a cost of some more overhead on features like perf and posix cpu timers slow-paths, which is probably not much important for nohz full users. Requested-by: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
1ca8ec53 |
|
27-Jan-2016 |
Wanpeng Li <kernellwp@gmail.com> |
tick/nohz: Set the correct expiry when switching to nohz/lowres mode commit 0ff53d096422 sets the next tick interrupt to the last jiffies update, i.e. in the past, because the forward operation is invoked before the set operation. There is no resulting damage (yet), but we get an extra pointless tick interrupt. Revert the order so we get the next tick interrupt in the future. Fixes: commit 0ff53d096422 "tick: sched: Force tick interrupt and get rid of softirq magic" Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1453893967-3458-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
7809998a |
|
25-Jan-2016 |
Arnd Bergmann <arnd@arndb.de> |
tick/sched: Hide unused oneshot timer code A couple of functions in kernel/time/tick-sched.c are only relevant for oneshot timer mode, i.e. when hires-timers or nohz mode are enabled. If both are disabled, we get gcc warnings about them: kernel/time/tick-sched.c:98:16: warning: 'tick_init_jiffy_update' defined but not used [-Wunused-function] static ktime_t tick_init_jiffy_update(void) ^ kernel/time/tick-sched.c:112:13: warning: 'tick_sched_do_timer' defined but not used [-Wunused-function] static void tick_sched_do_timer(ktime_t now) ^ kernel/time/tick-sched.c:134:13: warning: 'tick_sched_handle' defined but not used [-Wunused-function] static void tick_sched_handle(struct tick_sched *ts, struct pt_regs *regs) ^ This encloses the whole set of functions in an appropriate ifdef to avoid the warning and to make it clearer when they are used. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1453736525-1959191-1-git-send-email-arnd@arndb.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
46373a15 |
|
11-Jan-2016 |
Jean Delvare <jdelvare@suse.de> |
time: nohz: Expose tick_nohz_enabled The cpuidle subsystem needs it. Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
03e0d461 |
|
08-Dec-2015 |
Tejun Heo <tj@kernel.org> |
watchdog: introduce touch_softlockup_watchdog_sched() touch_softlockup_watchdog() is used to tell watchdog that scheduler stall is expected. One group of usage is from paths where the task may not be able to yield for a long time such as performing slow PIO to finicky device and coming out of suspend. The other is to account for scheduler and timer going idle. For scheduler softlockup detection, there's no reason to distinguish the two cases; however, workqueue lockup detector is planned and it can use the same signals from the former group while the latter would spuriously prevent detection. This patch introduces a new function touch_softlockup_watchdog_sched() and convert the latter group to call it instead. For now, it just calls touch_softlockup_watchdog() and there's no functional difference. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Ulrich Obergfell <uobergfe@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org>
|
#
55dbdcfa |
|
19-Nov-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched/cputime: Rename vtime_accounting_enabled() to vtime_accounting_cpu_enabled() vtime_accounting_enabled() checks if vtime is running on the current CPU and is as such a misnomer. Lets rename it to a function that reflect its locality. We are going to need the current name for a function that tells if vtime runs at all on some CPU. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1447948054-28668-6-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
82bbe34b |
|
19-Nov-2015 |
Peter Zijlstra <peterz@infradead.org> |
nohz: Clarify magic in tick_nohz_stop_sched_tick() While going through the nohz code I got stumped by some of it. This patch adds a few comments clarifying the code; based on discussion with Thomas. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Link: http://lkml.kernel.org/r/20151119162106.GO3816@twins.programming.kicks-ass.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
525705d1 |
|
09-Nov-2015 |
Byungchul Park <byungchul.park@lge.com> |
sched/fair: Consider missed ticks in NOHZ_FULL in update_cpu_load_nohz() Usually the tick can be stopped for an idle CPU in NOHZ. However in NOHZ_FULL mode, a non-idle CPU's tick can also be stopped. However, update_cpu_load_nohz() does not consider the case a non-idle CPU's tick has been stopped at all. This patch makes the update_cpu_load_nohz() know if the calling path comes from NOHZ_FULL or idle NOHZ. Signed-off-by: Byungchul Park <byungchul.park@lge.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1447115762-19734-3-git-send-email-byungchul.park@lge.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
7c8bb6cb |
|
01-Sep-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Assert existing housekeepers when nohz full enabled The code ensures that when nohz full is running, at least the boot CPU serves as a housekeeper and it can't be later offlined. Let's assert this assumption to make sure that we have CPUs to handle unbound jobs like workqueues and timers while nohz full CPUs run undisturbed. Also improve the comments on housekeeper offlining prevention. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Vatika Harlalka <vatikaharlalka@gmail.com> Link: http://lkml.kernel.org/r/1441119060-2230-3-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
de734f89 |
|
11-Jun-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Remove useless argument on tick_nohz_task_switch() Leftover from early code. Cc: Christoph Lameter <cl@linux.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
59d2c7ca |
|
29-May-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Move tick_nohz_restart_sched_tick() above its users Fix the function declaration/definition dance. Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Christoph Lameter <cl@linux.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
73738a95 |
|
27-May-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Restart nohz full tick from irq exit Restart the tick when necessary from the irq exit path. It makes nohz full more flexible, simplify the related IPIs and doesn't bring significant overhead on irq exit. In a longer term view, it will allow us to piggyback the nohz kick on the scheduler IPI in the future instead of sending a dedicated IPI that often doubles the scheduler IPI on task wakeup. This will require more changes though including careful review of resched_curr() callers to include nohz full needs. Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Christoph Lameter <cl@linux.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
59449359 |
|
27-May-2015 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Remove idle task special case On nohz full early days, idle dynticks and full dynticks weren't well integrated and we couldn't risk full dynticks calls on idle without risking messing up tick idle statistics. This is why we prevented such thing to happen. Nowadays full dynticks and idle dynticks are better integrated and interact without known issue. So lets remove that. Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Christoph Lameter <cl@linux.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
683be13a |
|
26-May-2015 |
Thomas Gleixner <tglx@linutronix.de> |
timer: Minimize nohz off overhead If nohz is disabled on the kernel command line the [hr]timer code still calls wake_up_nohz_cpu() and tick_nohz_full_cpu(), a pretty pointless exercise. Cache nohz_active in [hr]timer per cpu bases and avoid the overhead. Before: 48.10% hog [.] main 15.25% [kernel] [k] _raw_spin_lock_irqsave 9.76% [kernel] [k] _raw_spin_unlock_irqrestore 6.50% [kernel] [k] mod_timer 6.44% [kernel] [k] lock_timer_base.isra.38 3.87% [kernel] [k] detach_if_pending 3.80% [kernel] [k] del_timer 2.67% [kernel] [k] internal_add_timer 1.33% [kernel] [k] __internal_add_timer 0.73% [kernel] [k] timerfn 0.54% [kernel] [k] wake_up_nohz_cpu After: 48.73% hog [.] main 15.36% [kernel] [k] _raw_spin_lock_irqsave 9.77% [kernel] [k] _raw_spin_unlock_irqrestore 6.61% [kernel] [k] lock_timer_base.isra.38 6.42% [kernel] [k] mod_timer 3.90% [kernel] [k] detach_if_pending 3.76% [kernel] [k] del_timer 2.41% [kernel] [k] internal_add_timer 1.39% [kernel] [k] __internal_add_timer 0.76% [kernel] [k] timerfn We probably should have a cached value for nohz full in the per cpu bases as well to avoid the cpumask check. The base cache line is hot already, the cpumask not necessarily. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul McKenney <paulmck@linux.vnet.ibm.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Joonwoo Park <joonwoop@codeaurora.org> Cc: Wenbo Wang <wenbo.wang@memblaze.com> Link: http://lkml.kernel.org/r/20150526224512.207378134@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
bc7a34b8 |
|
26-May-2015 |
Thomas Gleixner <tglx@linutronix.de> |
timer: Reduce timer migration overhead if disabled Eric reported that the timer_migration sysctl is not really nice performance wise as it needs to check at every timer insertion whether the feature is enabled or not. Further the check does not live in the timer code, so we have an extra function call which checks an extra cache line to figure out that it is disabled. We can do better and store that information in the per cpu (hr)timer bases. I pondered to use a static key, but that's a nightmare to update from the nohz code and the timer base cache line is hot anyway when we select a timer base. The old logic enabled the timer migration unconditionally if CONFIG_NO_HZ was set even if nohz was disabled on the kernel command line. With this modification, we start off with migration disabled. The user visible sysctl is still set to enabled. If the kernel switches to NOHZ migration is enabled, if the user did not disable it via the sysctl prior to the switch. If nohz=off is on the kernel command line, migration stays disabled no matter what. Before: 47.76% hog [.] main 14.84% [kernel] [k] _raw_spin_lock_irqsave 9.55% [kernel] [k] _raw_spin_unlock_irqrestore 6.71% [kernel] [k] mod_timer 6.24% [kernel] [k] lock_timer_base.isra.38 3.76% [kernel] [k] detach_if_pending 3.71% [kernel] [k] del_timer 2.50% [kernel] [k] internal_add_timer 1.51% [kernel] [k] get_nohz_timer_target 1.28% [kernel] [k] __internal_add_timer 0.78% [kernel] [k] timerfn 0.48% [kernel] [k] wake_up_nohz_cpu After: 48.10% hog [.] main 15.25% [kernel] [k] _raw_spin_lock_irqsave 9.76% [kernel] [k] _raw_spin_unlock_irqrestore 6.50% [kernel] [k] mod_timer 6.44% [kernel] [k] lock_timer_base.isra.38 3.87% [kernel] [k] detach_if_pending 3.80% [kernel] [k] del_timer 2.67% [kernel] [k] internal_add_timer 1.33% [kernel] [k] __internal_add_timer 0.73% [kernel] [k] timerfn 0.54% [kernel] [k] wake_up_nohz_cpu Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul McKenney <paulmck@linux.vnet.ibm.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Joonwoo Park <joonwoop@codeaurora.org> Cc: Wenbo Wang <wenbo.wang@memblaze.com> Link: http://lkml.kernel.org/r/20150526224512.127050787@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
6b442bc8 |
|
07-May-2015 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: Fix !HIGH_RES_TIMERS hang Simon Horman reported this crash on a system with high-res timers disabled but nohz enabled: > ------------[ cut here ]------------ > kernel BUG at kernel/irq_work.c:135! BUG_ON(!irqs_disabled()); So something enabled interrupts in the periodic tick handling machinery, and that code path indeed has a local_irq_disable()/enable pair in tick_nohz_switch_to_nohz() which causes havoc. Fix it. This patch also fixes a +nohz -hrtimers hang reported by Ingo Molnar. Reported-by: Simon Horman <horms@verge.net.au> Reported-by: Ingo Molnar <mingo@kernel.org> Tested-by: Simon Horman <horms@verge.net.au> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: LAK <linux-arm-kernel@lists.infradead.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1505071425520.4225@nanos Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
c1ad348b |
|
14-Apr-2015 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Nohz: Rework next timer evaluation The evaluation of the next timer in the nohz code is based on jiffies while all the tick internals are nano seconds based. We have also to convert hrtimer nanoseconds to jiffies in the !highres case. That's just wrong and introduces interesting corner cases. Turn it around and convert the next timer wheel timer expiry and the rcu event to clock monotonic and base all calculations on nanoseconds. That identifies the case where no timer is pending clearly with an absolute expiry value of KTIME_MAX. Makes the code more readable and gets rid of the jiffies magic in the nohz code. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Link: http://lkml.kernel.org/r/20150414203502.184198593@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
157d29e1 |
|
14-Apr-2015 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Sched: Restructure code Get rid of one indentation level. Preparatory patch for a major rework. No functional change. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Link: http://lkml.kernel.org/r/20150414203502.101563235@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
0ff53d09 |
|
14-Apr-2015 |
Thomas Gleixner <tglx@linutronix.de> |
tick: sched: Force tick interrupt and get rid of softirq magic We already got rid of the hrtimer reprogramming loops and hoops as hrtimer now enforces an interrupt if the enqueued time is in the past. Do the same for the nohz non highres mode. That gets rid of the need to raise the softirq which only serves the purpose of getting the machine out of the inner idle loop. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Link: http://lkml.kernel.org/r/20150414203502.023464878@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
afc08b15 |
|
14-Apr-2015 |
Thomas Gleixner <tglx@linutronix.de> |
tick: sched: Remove hrtimer_active() checks hrtimer_start() enforces a timer interrupt if the timer is already expired. Get rid of the checks and the forward loop. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Link: http://lkml.kernel.org/r/20150414203501.943658239@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
c1797baf |
|
25-Mar-2015 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Move core only declarations and functions to core No point to expose everything to the world. People just believe such functions can be abused for whatever purposes. Sigh. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> [ Rebased on top of 4.0-rc5 ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Nicolas Pitre <nico@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/28017337.VbCUc39Gme@vostro.rjw.lan [ Merged to latest timers/core ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
ffda22c1 |
|
13-Feb-2015 |
Tejun Heo <tj@kernel.org> |
time: use %*pb[l] to print bitmaps including cpumasks and nodemasks printk and friends can now format bitmaps using '%*pb[l]'. cpumask and nodemask also provide cpumask_pr_args() and nodemask_pr_args() respectively which can be used to generate the two printf arguments necessary to format the specified cpu/nodemask. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
a5fd9733 |
|
18-Dec-2014 |
Thomas Gleixner <tglx@linutronix.de> |
tick/powerclamp: Remove tick_nohz_idle abuse commit 4dbd27711cd9 "tick: export nohz tick idle symbols for module use" was merged via the thermal tree without an explicit ack from the relevant maintainers. The exports are abused by the intel powerclamp driver which implements a fake idle state from a sched FIFO task. This causes all kinds of wreckage in the NOHZ core code which rightfully assumes that tick_nohz_idle_enter/exit() are only called from the idle task itself. Recent changes in the NOHZ core lead to a failure of the powerclamp driver and now people try to hack completely broken and backwards workarounds into the NOHZ core code. This is completely unacceptable and just papers over the real problem. There are way more subtle issues lurking around the corner. The real solution is to fix the powerclamp driver by rewriting it with a sane concept, but that's beyond the scope of this. So the only solution for now is to remove the calls into the core NOHZ code from the powerclamp trainwreck along with the exports. Fixes: d6d71ee4a14a "PM: Introduce Intel PowerClamp Driver" Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Pan Jacob jun <jacob.jun.pan@intel.com> Cc: LKP <lkp@01.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Zhang Rui <rui.zhang@intel.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1412181110110.17382@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
aa6da514 |
|
21-Oct-2014 |
Paul E. McKenney <paulmck@kernel.org> |
rcu: Remove "cpu" argument to rcu_needs_cpu() The "cpu" argument to rcu_needs_cpu() is always the current CPU, so drop it. This in turn allows the "cpu" argument to rcu_cpu_has_callbacks() to be removed, which allows the uses of "cpu" in both functions to be replaced with a this_cpu_ptr(). Again, the anticipated cross-CPU uses of these functions has been replaced by NO_HZ_FULL. Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
|
#
56e4dea8 |
|
27-Oct-2014 |
Christoph Lameter <cl@linux.com> |
percpu: Convert remaining __get_cpu_var uses in 3.18-rcX During the 3.18 merge period additional __get_cpu_var uses were added. The patch converts these to this_cpu_ptr(). Signed-off-by: Christoph Lameter <cl@linux.com> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Tejun Heo <tj@kernel.org>
|
#
fe0f4976 |
|
30-Sep-2014 |
Martin Schwidefsky <schwidefsky@de.ibm.com> |
s390/nohz: use a per-cpu flag for arch_needs_cpu Move the nohz_delay bit from the s390_idle data structure to the per-cpu flags. Clear the nohz delay flag in __cpu_disable and remove the cpu hotplug notifier that used to do this. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
#
9b01f5bf |
|
17-Aug-2014 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: nohz full depends on irq work self IPI support The nohz full functionality depends on IRQ work to trigger its own interrupts. As it's used to restart the tick, we can't rely on the tick fallback for irq work callbacks, ie: we can't use the tick to restart the tick itself. Lets reject the full dynticks initialization if that arch support isn't available. As a side effect, this makes sure that nohz kick is never called from the tick. That otherwise would result in illegal hrtimer self-cancellation and lockup. Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
4327b15f |
|
17-Aug-2014 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Consolidate nohz full init code The supports for CONFIG_NO_HZ_FULL_ALL=y and the nohz_full= kernel parameter both have their own way to do the same thing: allocate full dynticks cpumasks, fill them and initialize some state variables. Lets consolidate that all in the same place. While at it, convert some regular printk message to warnings when fundamental allocations fail. Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
40bea039 |
|
13-Aug-2014 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Restore NMI safe local irq work for local nohz kick The local nohz kick is currently used by perf which needs it to be NMI-safe. Recent commit though (7d1311b93e58ed55f3a31cc8f94c4b8fe988a2b9) changed its implementation to fire the local kick using the remote kick API. It was convenient to make the code more generic but the remote kick isn't NMI-safe. As a result: WARNING: CPU: 3 PID: 18062 at kernel/irq_work.c:72 irq_work_queue_on+0x11e/0x140() CPU: 3 PID: 18062 Comm: trinity-subchil Not tainted 3.16.0+ #34 0000000000000009 00000000903774d1 ffff880244e06c00 ffffffff9a7f1e37 0000000000000000 ffff880244e06c38 ffffffff9a0791dd ffff880244fce180 0000000000000003 ffff880244e06d58 ffff880244e06ef8 0000000000000000 Call Trace: <NMI> [<ffffffff9a7f1e37>] dump_stack+0x4e/0x7a [<ffffffff9a0791dd>] warn_slowpath_common+0x7d/0xa0 [<ffffffff9a07930a>] warn_slowpath_null+0x1a/0x20 [<ffffffff9a17ca1e>] irq_work_queue_on+0x11e/0x140 [<ffffffff9a10a2c7>] tick_nohz_full_kick_cpu+0x57/0x90 [<ffffffff9a186cd5>] __perf_event_overflow+0x275/0x350 [<ffffffff9a184f80>] ? perf_event_task_disable+0xa0/0xa0 [<ffffffff9a01a4cf>] ? x86_perf_event_set_period+0xbf/0x150 [<ffffffff9a187934>] perf_event_overflow+0x14/0x20 [<ffffffff9a020386>] intel_pmu_handle_irq+0x206/0x410 [<ffffffff9a0b54d3>] ? arch_vtime_task_switch+0x63/0x130 [<ffffffff9a01937b>] perf_event_nmi_handler+0x2b/0x50 [<ffffffff9a007b72>] nmi_handle+0xd2/0x390 [<ffffffff9a007aa5>] ? nmi_handle+0x5/0x390 [<ffffffff9a0d131b>] ? lock_release+0xab/0x330 [<ffffffff9a008062>] default_do_nmi+0x72/0x1c0 [<ffffffff9a0c925f>] ? cpuacct_account_field+0xcf/0x200 [<ffffffff9a008268>] do_nmi+0xb8/0x100 Lets fix this by restoring the use of local irq work for the nohz local kick. Reported-by: Catalin Iacob <iacobcatalin@gmail.com> Reported-and-tested-by: Dave Jones <davej@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
4a32fea9 |
|
16-Aug-2014 |
Christoph Lameter <cl@linux.com> |
scheduler: Replace __get_cpu_var with this_cpu_ptr Convert all uses of __get_cpu_var for address calculation to use this_cpu_ptr instead. [Uses of __get_cpu_var with cpumask_var_t are no longer handled by this patch] Cc: Peter Zijlstra <peterz@infradead.org> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Christoph Lameter <cl@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org>
|
#
22127e93 |
|
16-Aug-2014 |
Christoph Lameter <cl@linux.com> |
time: Replace __get_cpu_var uses Convert uses of __get_cpu_var for creating a address from a percpu offset to this_cpu_ptr. The two cases where get_cpu_var is used to actually access a percpu variable are changed to use this_cpu_read/raw_cpu_read. Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Christoph Lameter <cl@linux.com> Signed-off-by: Tejun Heo <tj@kernel.org>
|
#
2a16fc93 |
|
12-Jun-2014 |
Viresh Kumar <viresh.kumar@linaro.org> |
nohz: Avoid tick's double reprogramming in highres mode In highres mode, the tick reschedules itself unconditionally to the next jiffies. However while this clock reprogramming is relevant when the tick is in periodic mode, it's not that interesting when we run in dynticks mode because irq exit is likely going to overwrite the next tick to some randomly deferred future. So lets just get rid of this tick self rescheduling in dynticks mode. This way we can avoid some clockevents double write in favourable scenarios like when we stop the tick completely in idle while no other hrtimer is pending. Suggested-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
b5e995e6 |
|
12-Jun-2014 |
Viresh Kumar <viresh.kumar@linaro.org> |
nohz: Fix spurious periodic tick behaviour in low-res dynticks mode When we reach the end of the tick handler, we unconditionally reschedule the next tick to the next jiffy. Then on irq exit, the nohz code overrides that setting if needed and defers the next tick as far away in the future as possible. Now in the best dynticks case, when we actually don't need any tick in the future (ie: expires == KTIME_MAX), low-res and high-res behave differently. What we want in this case is to cancel the next tick programmed by the previous one. That's what we do in high-res mode. OTOH we lack a low-res mode equivalent of hrtimer_cancel() so we simply don't do anything in this case and the next tick remains scheduled to jiffies + 1. As a result, in low-res mode, when the dynticks code determines that no tick is needed in the future, we can recursively get a spurious tick every jiffy because then the next tick is always reprogrammed from the tick handler and is never cancelled. And this can happen indefinetly until some subsystem actually needs a precise tick in the future and only then we eventually overwrite the previous tick handler setting to defer the next tick. We are fixing this by introducing the ONESHOT_STOPPED mode which will let us pause a clockevent when no further interrupt is needed. Meanwhile we can't expect all drivers to support this new mode. So lets reduce much of the symptoms by skipping the nohz-blind tick rescheduling from the tick-handler when the CPU is in dynticks mode. That tick rescheduling wrongly assumed periodicity and the low-res dynticks code can't cancel such decision. This breaks the recursive (and thus the worst) part of the problem. In the worst case now, we'll get only one extra tick due to uncancelled tick scheduled before we entered dynticks mode. This also removes a needless clockevent write on idle ticks. Since those clock write are usually considered to be slow, it's a general win. Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
c0f489d2 |
|
04-Jun-2014 |
Paul E. McKenney <paulmck@kernel.org> |
rcu: Bind grace-period kthreads to non-NO_HZ_FULL CPUs Binding the grace-period kthreads to the timekeeping CPU resulted in significant performance decreases for some workloads. For more detail, see: https://lkml.org/lkml/2014/6/3/395 for benchmark numbers https://lkml.org/lkml/2014/6/4/218 for CPU statistics It turns out that it is necessary to bind the grace-period kthreads to the timekeeping CPU only when all but CPU 0 is a nohz_full CPU on the one hand or if CONFIG_NO_HZ_FULL_SYSIDLE=y on the other. In other cases, it suffices to bind the grace-period kthreads to the set of non-nohz_full CPUs. This commit therefore creates a tick_nohz_not_full_mask that is the complement of tick_nohz_full_mask, and then binds the grace-period kthread to the set of CPUs indicated by this new mask, which covers the CONFIG_NO_HZ_FULL_SYSIDLE=n case. The CONFIG_NO_HZ_FULL_SYSIDLE=y case still binds the grace-period kthreads to the timekeeping CPU. This commit also includes the tick_nohz_full_enabled() check suggested by Frederic Weisbecker. Reported-by: Jet Chen <jet.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [ paulmck: Created housekeeping_affine() and housekeeping_mask per fweisbec feedback. ]
|
#
3d36aebc |
|
04-Jun-2014 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Support nohz full remote kick Remotely kicking a full nohz CPU in order to make it re-evaluate its next tick is currently implemented using the scheduler IPI. However this bloats a scheduler fast path with an off-topic feature. The scheduler tick was abused here for its cool "callable anywhere/anytime" properties. But now that the irq work subsystem can queue remote callbacks, it's a perfect fit to safely queue IPIs when interrupts are disabled without worrying about concurrent callers. So lets implement remote kick on top of irq work. This is going to be used when a new event requires the next tick to be recalculated: more than 1 task competing on the CPU, timer armed, ... Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
27630532 |
|
14-Apr-2014 |
Viresh Kumar <viresh.kumar@linaro.org> |
tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz() Since commit d689fe222 (NOHZ: Check for nohz active instead of nohz enabled) the tick_nohz_switch_to_nohz() function returns because it checks for the tick_nohz_active flag. This can't be set, because the function itself sets it. Undo the change in tick_nohz_switch_to_nohz(). Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: linaro-kernel@lists.linaro.org Cc: fweisbec@gmail.com Cc: Arvind.Chauhan@arm.com Cc: linaro-networking@linaro.org Cc: <stable@vger.kernel.org> # 3.13+ Link: http://lkml.kernel.org/r/40939c05f2d65d781b92b20302b02243d0654224.1397537987.git.viresh.kumar@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
03e6bdc5 |
|
14-Apr-2014 |
Viresh Kumar <viresh.kumar@linaro.org> |
tick-sched: Don't call update_wall_time() when delta is lesser than tick_period In tick_do_update_jiffies64() we are processing ticks only if delta is greater than tick_period. This is what we are supposed to do here and it broke a bit with this patch: commit 47a1b796 (tick/timekeeping: Call update_wall_time outside the jiffies lock) With above patch, we might end up calling update_wall_time() even if delta is found to be smaller that tick_period. Fix this by returning when the delta is less than tick period. [ tglx: Made it a 3 liner and massaged changelog ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: linaro-kernel@lists.linaro.org Cc: fweisbec@gmail.com Cc: Arvind.Chauhan@arm.com Cc: linaro-networking@linaro.org Cc: John Stultz <john.stultz@linaro.org> Cc: <stable@vger.kernel.org> # v3.14+ Link: http://lkml.kernel.org/r/80afb18a494b0bd9710975bcc4de134ae323c74f.1397537987.git.viresh.kumar@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
e9a2eb40 |
|
27-Nov-2013 |
Alex Shi <alex.shi@linux.alibaba.com> |
nohz_full: fix code style issue of tick_nohz_full_stop_tick Code usually starts with 'tab' instead of 7 'space' in kernel Signed-off-by: Alex Shi <alex.shi@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alex Shi <alex.shi@linaro.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Kevin Hilman <khilman@linaro.org> Link: http://lkml.kernel.org/r/1386074112-30754-2-git-send-email-alex.shi@linaro.org Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
855a0fc3 |
|
16-Dec-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Get timekeeping max deferment outside jiffies_lock We don't need to fetch the timekeeping max deferment under the jiffies_lock seqlock. If the clocksource is updated concurrently while we stop the tick, stop machine is called and the tick will be reevaluated again along with uptodate jiffies and its related values. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alex Shi <alex.shi@linaro.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Kevin Hilman <khilman@linaro.org> Link: http://lkml.kernel.org/r/1387320692-28460-9-git-send-email-fweisbec@gmail.com Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
5acac1be |
|
04-Dec-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
tick: Rename tick_check_idle() to tick_irq_enter() This makes the code more symetric against the existing tick functions called on irq exit: tick_irq_exit() and tick_nohz_irq_exit(). These function are also symetric as they mirror each other's action: we start to account idle time on irq exit and we stop this accounting on irq entry. Also the tick is stopped on irq exit and timekeeping catches up with the tickless time elapsed until we reach irq entry. This rename was suggested by Peter Zijlstra a long while ago but it got forgotten in the mass. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alex Shi <alex.shi@linaro.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Kevin Hilman <khilman@linaro.org> Link: http://lkml.kernel.org/r/1387320692-28460-2-git-send-email-fweisbec@gmail.com Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
35af99e6 |
|
28-Nov-2013 |
Peter Zijlstra <peterz@infradead.org> |
sched/clock, x86: Use a static_key for sched_clock_stable In order to avoid the runtime condition and variable load turn sched_clock_stable into a static_key. Also provide a shorter implementation of local_clock() and cpu_clock(int) when sched_clock_stable==1. MAINLINE PRE POST sched_clock_stable: 1 1 1 (cold) sched_clock: 329841 221876 215295 (cold) local_clock: 301773 234692 220773 (warm) sched_clock: 38375 25602 25659 (warm) local_clock: 100371 33265 27242 (warm) rdtsc: 27340 24214 24208 sched_clock_stable: 0 0 0 (cold) sched_clock: 382634 235941 237019 (cold) local_clock: 396890 297017 294819 (warm) sched_clock: 38194 25233 25609 (warm) local_clock: 143452 71234 71232 (warm) rdtsc: 27345 24245 24243 Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/n/tip-eummbdechzz37mwmpags1gjr@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
47a1b796 |
|
12-Dec-2013 |
John Stultz <john.stultz@linaro.org> |
tick/timekeeping: Call update_wall_time outside the jiffies lock Since the xtime lock was split into the timekeeping lock and the jiffies lock, we no longer need to call update_wall_time() while holding the jiffies lock. Thus, this patch splits update_wall_time() out from do_timer(). This allows us to get away from calling clock_was_set_delayed() in update_wall_time() and instead use the standard clock_was_set() call that previously would deadlock, as it causes the jiffies lock to be acquired. Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: John Stultz <john.stultz@linaro.org>
|
#
e8fcaa5c |
|
07-Aug-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Convert a few places to use local per cpu accesses A few functions use remote per CPU access APIs when they deal with local values. Just do the right conversion to improve performance, code readability and debug checks. While at it, lets extend some of these function names with *_this_cpu() suffix in order to display their purpose more clearly. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org>
|
#
0e576acb |
|
28-Nov-2013 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off If CONFIG_NO_HZ=n tick_nohz_get_sleep_length() returns NSEC_PER_SEC/HZ. If CONFIG_NO_HZ=y and the nohz functionality is disabled via the command line option "nohz=off" or not enabled due to missing hardware support, then tick_nohz_get_sleep_length() returns 0. That happens because ts->sleep_length is never set in that case. Set it to NSEC_PER_SEC/HZ when the NOHZ mode is inactive. Reported-by: Michal Hocko <mhocko@suse.cz> Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
d689fe22 |
|
13-Nov-2013 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: Check for nohz active instead of nohz enabled RCU and the fine grained idle time accounting functions check tick_nohz_enabled. But that variable is merily telling that NOHZ has been enabled in the config and not been disabled on the command line. But it does not tell anything about nohz being active. That's what all this should check for. Matthew reported, that the idle accounting on his old P1 machine showed bogus values, when he enabled NOHZ in the config and did not disable it on the kernel command line. The reason is that his machine uses (refined) jiffies as a clocksource which explains why the "fine" grained accounting went into lala land, because it depends on when the system goes and leaves idle relative to the jiffies increment. Provide a tick_nohz_active indicator and let RCU and the accounting code use this instead of tick_nohz_enable. Reported-and-tested-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: john.stultz@linaro.org Cc: mwhitehe@redhat.com Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311132052240.30673@ionos.tec.linutronix.de
|
#
c2e7fcf5 |
|
02-Aug-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Include local CPU in full dynticks global kick tick_nohz_full_kick_all() is useful to notify all full dynticks CPUs that there is a system state change to checkout before re-evaluating the need for the tick. Unfortunately this is implemented using smp_call_function_many() that ignores the local CPU. This CPU also needs to re-evaluate the tick. on_each_cpu_mask() is not useful either because we don't want to re-evaluate the tick state in place but asynchronously from an IPI to avoid messing up with any random locking scenario. So lets call tick_nohz_full_kick() from tick_nohz_full_kick_all() so that the usual irq work takes care of it. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1375460996-16329-4-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
d13508f9 |
|
24-Jul-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Optimize full dynticks's sched hooks with static keys Scheduler IPIs and task context switches are serious fast path. Let's try to hide as much as we can the impact of full dynticks APIs' off case that are called on these sites through the use of static keys. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org>
|
#
460775df |
|
24-Jul-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Optimize full dynticks state checks with static keys These APIs are frequenctly accessed and priority is given to optimize the full dynticks off-case in order to let distros enable this feature without suffering from significant performance regressions. Let's inline these APIs and optimize them with static keys. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org>
|
#
73867dcd |
|
24-Jul-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Rename a few state variables Rename the full dynticks's cpumask and cpumask state variables to some more exportable names. These will be used later from global headers to optimize the main full dynticks APIs in conjunction with static keys. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org>
|
#
2e709338 |
|
09-Jul-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Only enable context tracking on full dynticks CPUs The context tracking subsystem has the ability to selectively enable the tracking on any defined subset of CPU. This means that we can define a CPU range that doesn't run the context tracking and another range that does. Now what we want in practice is to enable the tracking on full dynticks CPUs only. In order to perform this, we just need to pass our full dynticks CPU range selection from the full dynticks subsystem to the context tracking. This way we can spare the overhead of RCU user extended quiescent state and vtime maintainance on the CPUs that are outside the full dynticks range. Just keep in mind the raw context tracking itself is still necessary everywhere. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org>
|
#
14851912 |
|
26-Jul-2013 |
Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
Revert "cpuidle: Quickly notice prediction failure for repeat mode" Revert commit 69a37bea (cpuidle: Quickly notice prediction failure for repeat mode), because it has been identified as the source of a significant performance regression in v3.8 and later as explained by Jeremy Eder: We believe we've identified a particular commit to the cpuidle code that seems to be impacting performance of variety of workloads. The simplest way to reproduce is using netperf TCP_RR test, so we're using that, on a pair of Sandy Bridge based servers. We also have data from a large database setup where performance is also measurably/positively impacted, though that test data isn't easily share-able. Included below are test results from 3 test kernels: kernel reverts ----------------------------------------------------------- 1) vanilla upstream (no reverts) 2) perfteam2 reverts e11538d1f03914eb92af5a1a378375c05ae8520c 3) test reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4 e11538d1f03914eb92af5a1a378375c05ae8520c In summary, netperf TCP_RR numbers improve by approximately 4% after reverting 69a37beabf1f0a6705c08e879bdd5d82ff6486c4. When 69a37beabf1f0a6705c08e879bdd5d82ff6486c4 is included, C0 residency never seems to get above 40%. Taking that patch out gets C0 near 100% quite often, and performance increases. The below data are histograms representing the %c0 residency @ 1-second sample rates (using turbostat), while under netperf test. - If you look at the first 4 histograms, you can see %c0 residency almost entirely in the 30,40% bin. - The last pair, which reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4, shows %c0 in the 80,90,100% bins. Below each kernel name are netperf TCP_RR trans/s numbers for the particular kernel that can be disclosed publicly, comparing the 3 test kernels. We ran a 4th test with the vanilla kernel where we've also set /dev/cpu_dma_latency=0 to show overall impact boosting single-threaded TCP_RR performance over 11% above baseline. 3.10-rc2 vanilla RX + c0 lock (/dev/cpu_dma_latency=0): TCP_RR trans/s 54323.78 ----------------------------------------------------------- 3.10-rc2 vanilla RX (no reverts) TCP_RR trans/s 48192.47 Receiver %c0 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 0]: 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 59]: *********************************************************** 40.0000 - 50.0000 [ 1]: * 50.0000 - 60.0000 [ 0]: 60.0000 - 70.0000 [ 0]: 70.0000 - 80.0000 [ 0]: 80.0000 - 90.0000 [ 0]: 90.0000 - 100.0000 [ 0]: Sender %c0 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 0]: 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 11]: *********** 40.0000 - 50.0000 [ 49]: ************************************************* 50.0000 - 60.0000 [ 0]: 60.0000 - 70.0000 [ 0]: 70.0000 - 80.0000 [ 0]: 80.0000 - 90.0000 [ 0]: 90.0000 - 100.0000 [ 0]: ----------------------------------------------------------- 3.10-rc2 perfteam2 RX (reverts commit e11538d1f03914eb92af5a1a378375c05ae8520c) TCP_RR trans/s 49698.69 Receiver %c0 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 1]: * 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 59]: *********************************************************** 40.0000 - 50.0000 [ 0]: 50.0000 - 60.0000 [ 0]: 60.0000 - 70.0000 [ 0]: 70.0000 - 80.0000 [ 0]: 80.0000 - 90.0000 [ 0]: 90.0000 - 100.0000 [ 0]: Sender %c0 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 0]: 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 2]: ** 40.0000 - 50.0000 [ 58]: ********************************************************** 50.0000 - 60.0000 [ 0]: 60.0000 - 70.0000 [ 0]: 70.0000 - 80.0000 [ 0]: 80.0000 - 90.0000 [ 0]: 90.0000 - 100.0000 [ 0]: ----------------------------------------------------------- 3.10-rc2 test RX (reverts 69a37beabf1f0a6705c08e879bdd5d82ff6486c4 and e11538d1f03914eb92af5a1a378375c05ae8520c) TCP_RR trans/s 47766.95 Receiver %c0 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 1]: * 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 27]: *************************** 40.0000 - 50.0000 [ 2]: ** 50.0000 - 60.0000 [ 0]: 60.0000 - 70.0000 [ 2]: ** 70.0000 - 80.0000 [ 0]: 80.0000 - 90.0000 [ 0]: 90.0000 - 100.0000 [ 28]: **************************** Sender: 0.0000 - 10.0000 [ 1]: * 10.0000 - 20.0000 [ 0]: 20.0000 - 30.0000 [ 0]: 30.0000 - 40.0000 [ 11]: *********** 40.0000 - 50.0000 [ 0]: 50.0000 - 60.0000 [ 1]: * 60.0000 - 70.0000 [ 0]: 70.0000 - 80.0000 [ 3]: *** 80.0000 - 90.0000 [ 7]: ******* 90.0000 - 100.0000 [ 38]: ************************************** These results demonstrate gaining back the tendency of the CPU to stay in more responsive, performant C-states (and thus yield measurably better performance), by reverting commit 69a37beabf1f0a6705c08e879bdd5d82ff6486c4. Requested-by: Jeremy Eder <jeder@redhat.com> Tested-by: Len Brown <len.brown@intel.com> Cc: 3.8+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
ca06416b |
|
15-Jul-2013 |
Li Zhong <zhong@linux.vnet.ibm.com> |
nohz: fix compile warning in tick_nohz_init() cpu is not used after commit 5b8621a68fdcd2baf1d3b413726f913a5254d46a Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
543487c7 |
|
16-Jul-2013 |
Steven Rostedt <rostedt@goodmis.org> |
nohz: Do not warn about unstable tsc unless user uses nohz_full If the user enables CONFIG_NO_HZ_FULL and runs the kernel on a machine with an unstable TSC, it will produce a WARN_ON dump as well as taint the kernel. This is a bit extreme for a kernel that just enables a feature but doesn't use it. The warning should only happen if the user tries to use the feature by either adding nohz_full to the kernel command line, or by enabling CONFIG_NO_HZ_FULL_ALL that makes nohz used on all CPUs at boot up. Note, this second feature should not (yet) be used by distros or anyone that doesn't care if NO_HZ is used or not. Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kevin Hilman <khilman@linaro.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
0db0628d |
|
19-Jun-2013 |
Paul Gortmaker <paul.gortmaker@windriver.com> |
kernel: delete __cpuinit usage from all core kernel files The __cpuinit type of throwaway sections might have made sense some time ago when RAM was more constrained, but now the savings do not offset the cost and complications. For example, the fix in commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time") is a good example of the nasty type of bugs that can be created with improper use of the various __init prefixes. After a discussion on LKML[1] it was decided that cpuinit should go the way of devinit and be phased out. Once all the users are gone, we can then finally remove the macros themselves from linux/init.h. This removes all the uses of the __cpuinit macros from C files in the core kernel directories (kernel, init, lib, mm, and include) that don't really have a specific maintainer. [1] https://lkml.org/lkml/2013/5/20/589 Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
#
5b8621a6 |
|
08-Jun-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs Building full dynticks now implies that all CPUs are forced into RCU nocb mode through CONFIG_RCU_NOCB_CPU_ALL. The dynamic check has become useless. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Borislav Petkov <bp@alien8.de>
|
#
e12d0271 |
|
10-May-2013 |
Steven Rostedt <rostedt@goodmis.org> |
nohz: Warn if the machine can not perform nohz_full If the user configures NO_HZ_FULL and defines nohz_full=XXX on the kernel command line, or enables NO_HZ_FULL_ALL, but nohz fails due to the machine having a unstable clock, warn about it. We do not want users thinking that they are getting the benefit of nohz when their machine can not support it. Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
#
1a7f829f |
|
17-May-2013 |
Li Zhong <zhong@linux.vnet.ibm.com> |
nohz: Fix notifier return val that enforce timekeeping In tick_nohz_cpu_down_callback() if the cpu is the one handling timekeeping, we must return something that stops the CPU_DOWN_PREPARE notifiers and then start notify CPU_DOWN_FAILED on the already called notifier call backs. However traditional errno values are not handled by the notifier unless these are encapsulated using errno_to_notifier(). Hence the current -EINVAL is misinterpreted and converted to junk after notifier_to_errno(), leaving the notifier subsystem to random behaviour such as eventually allowing the cpu to go down. Fix this by using the standard NOTIFY_BAD instead. Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
f7ea0fd6 |
|
13-May-2013 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Don't invoke tick_nohz_stop_sched_tick() if the cpu is offline commit 5b39939a4 (nohz: Move ts->idle_calls incrementation into strict idle logic) moved code out of tick_nohz_stop_sched_tick() and missed to bail out when the cpu is offline. That's causing subsequent failures as an offline CPU is supposed to die and not to fiddle with nohz magic. Return false in can_stop_idle_tick() if the cpu is offline. Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz> Reported-and-tested-by: Prarit Bhargava <prarit@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Tony Luck <tony.luck@intel.com> Cc: x86@kernel.org Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1305132138160.2863@ionos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
4b0c0f29 |
|
03-May-2013 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Cleanup NOHZ per cpu data on cpu down Prarit reported a crash on CPU offline/online. The reason is that on CPU down the NOHZ related per cpu data of the dead cpu is not cleaned up. If at cpu online an interrupt happens before the per cpu tick device is registered the irq_enter() check potentially sees stale data and dereferences a NULL pointer. Cleanup the data after the cpu is dead. Reported-by: Prarit Bhargava <prarit@redhat.com> Cc: stable@vger.kernel.org Cc: Mike Galbraith <bitbucket@online.de> Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1305031451561.2886@ionos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
265f22a9 |
|
02-May-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
sched: Keep at least 1 tick per second for active dynticks tasks The scheduler doesn't yet fully support environments with a single task running without a periodic tick. In order to ensure we still maintain the duties of scheduler_tick(), keep at least 1 tick per second. This makes sure that we keep the progression of various scheduler accounting and background maintainance even with a very low granularity. Examples include cpu load, sched average, CFS entity vruntime, avenrun and events such as load balancing, amongst other details handled in sched_class::task_tick(). This limitation will be removed in the future once we get these individual items to work in full dynticks CPUs. Suggested-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Christoph Lameter <cl@linux.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
6296ace4 |
|
27-Apr-2013 |
Li Zhong <zhong@linux.vnet.ibm.com> |
nohz: Protect smp_processor_id() in tick_nohz_task_switch() I saw following error when testing the latest nohz code on Power: [ 85.295384] BUG: using smp_processor_id() in preemptible [00000000] code: rsyslogd/3493 [ 85.295396] caller is .tick_nohz_task_switch+0x1c/0xb8 [ 85.295402] Call Trace: [ 85.295408] [c0000001fababab0] [c000000000012dc4] .show_stack+0x110/0x25c (unreliable) [ 85.295420] [c0000001fababba0] [c0000000007c4b54] .dump_stack+0x20/0x30 [ 85.295430] [c0000001fababc10] [c00000000044eb74] .debug_smp_processor_id+0xf4/0x124 [ 85.295438] [c0000001fababca0] [c0000000000d7594] .tick_nohz_task_switch+0x1c/0xb8 [ 85.295447] [c0000001fababd20] [c0000000000b9748] .finish_task_switch+0x13c/0x160 [ 85.295455] [c0000001fababdb0] [c0000000000bbe50] .schedule_tail+0x50/0x124 [ 85.295463] [c0000001fababe30] [c000000000009dc8] .ret_from_fork+0x4/0x54 The code below moves the test into local_irq_save/restore section to avoid the above complaint. Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paul McKenney <paulmck@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/1367119558.6391.34.camel@ThinkPad-T5421.cn.ibm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
47aa8b6c |
|
26-Apr-2013 |
Ingo Molnar <mingo@kernel.org> |
nohz: Reduce overhead under high-freq idling patterns One testbox of mine (Intel Nehalem, 16-way) uses MWAIT for its idle routine, which apparently can break out of its idle loop rather frequently, with high frequency. In that case NO_HZ_FULL=y kernels show high ksoftirqd overhead and constant context switching, because tick_nohz_stop_sched_tick() will, if delta_jiffies == 0, mis-identify this as a timer event - activating the TIMER_SOFTIRQ, which wakes up ksoftirqd. Fix this by treating delta_jiffies == 0 the same way we treat other short wakeups, delta_jiffies == 1. Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
cb41a290 |
|
20-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Add basic tracing It's not obvious to find out why the full dynticks subsystem doesn't always stop the tick: whether this is due to kthreads, posix timers, perf events, etc... These new tracepoints are here to help the user diagnose the failures and test this feature. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
99e5ada9 |
|
20-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Re-evaluate the tick for the new task after a context switch When a task is scheduled in, it may have some properties of its own that could make the CPU reconsider the need for the tick: posix cpu timers, perf events, ... So notify the full dynticks subsystem when a task gets scheduled in and re-check the tick dependency at this stage. This is done through a self IPI to avoid messing up with any current lock scenario. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
5811d996 |
|
20-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Prepare to stop the tick on irq exit Interrupt exit is a natural place to stop the tick: it happens after all events happening before and during the irq which are liable to update the dependency on the tick occured. Also it makes sure that any check on tick dependency is well ordered against dynticks kick IPIs. Bring in the infrastructure that performs the tick dependency checks on irq exit and shut it down if these checks show that we can do it safely. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
9014c45d |
|
20-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Implement full dynticks kick Implement the full dynticks kick that is performed from IPIs sent by various subsystems (scheduler, posix timers, ...) when they want to notify about a new event that may reconsider the dependency on the tick. Most of the time, such an event end up restarting the tick. (Part of the design with subsystems providing *_can_stop_tick() helpers suggested by Peter Zijlstra a while ago). Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
ff442c51 |
|
20-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Re-evaluate the tick from the scheduler IPI The scheduler IPI is used by the scheduler to kick full dynticks CPUs asynchronously when more than one task are running or when a new timer list timer is enqueued. This way the destination CPU can decide to restart the tick to handle this new situation. Now let's call that kick in the scheduler IPI. (Reusing the scheduler IPI rather than implementing a new IPI was suggested by Peter Zijlstra a while ago) Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
f98823ac |
|
26-Mar-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: New option to default all CPUs in full dynticks range Provide a new kernel config that defaults all CPUs to be part of the full dynticks range, except the boot one for timekeeping. This default setting is overriden by the nohz_full= boot option if passed by the user. This is helpful for those who don't need a finegrained range of full dynticks CPU and also for automated testing. Suggested-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
d1e43fa5 |
|
26-Mar-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Ensure full dynticks CPUs are RCU nocbs We need full dynticks CPU to also be RCU nocb so that we don't have to keep the tick to handle RCU callbacks. Make sure the range passed to nohz_full= boot parameter is a subset of rcu_nocbs= The CPUs that fail to meet this requirement will be excluded from the nohz_full range. This is checked early in boot time, before any CPU has the opportunity to stop its tick. Suggested-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
0453b435 |
|
26-Mar-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Force boot CPU outside full dynticks range The timekeeping job must be able to run early on boot because there may be some pre-SMP (and thus pre-initcalls ) components that rely on it. The IO-APIC is one such users as it tests the timer health by watching jiffies progression. Given that it happens before we know the initial online set, we can't rely on it to select a timekeeper. We need one before SMP time otherwise we simply crash on boot. To fix this and keep things simple for now, force the boot CPU outside of the full dynticks range in any case and do this early on kernel parameter parsing time. We might want a trickier solution later, expecially for aSMP architectures that need to assign housekeeping tasks to arbitrary low power CPUs. But it's still first pass KISS time for now. Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
76c24fb0 |
|
17-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: New APIs to re-evaluate the tick on full dynticks CPUs Provide two new helpers in order to notify the full dynticks CPUs about some internal system changes against which they may reconsider the state of their tick. Some practical examples include: posix cpu timers, perf tick and sched clock tick. For now the notifying handler, implemented through IPIs, is a stub that will be implemented when we get the tick stop/restart infrastructure in. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
c5bfece2 |
|
12-Apr-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Switch from "extended nohz" to "full nohz" based naming "Extended nohz" was used as a naming base for the full dynticks API and Kconfig symbols. It reflects the fact the system tries to stop the tick in more places than just idle. But that "extended" name is a bit opaque and vague. Rename it to "full" makes it clearer what the system tries to do under this config: try to shutdown the tick anytime it can. The various constraints that prevent that to happen shouldn't be considered as fundamental properties of this feature but rather technical issues that may be solved in the future. Reported-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
1034fc2f |
|
26-Mar-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Print final full dynticks CPUs range on boot Given that we apply a few restrictions on the full dynticks CPUs range (keep an online timekeeper oustide the range, then in the future have the range be an RCU nocb CPUs subset), let's print the final resulting range of full dynticks CPUs to the user so that he knows what's really going to run. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
3451d024 |
|
10-Aug-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Rename CONFIG_NO_HZ to CONFIG_NO_HZ_COMMON We are planning to convert the dynticks Kconfig options layout into a choice menu. The user must be able to easily pick any of the following implementations: constant periodic tick, idle dynticks, full dynticks. As this implies a mutual exclusion, the two dynticks implementions need to converge on the selection of a common Kconfig option in order to ease the sharing of a common infrastructure. It would thus seem pretty natural to reuse CONFIG_NO_HZ to that end. It already implements all the idle dynticks code and the full dynticks depends on all that code for now. So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ. On the other hand we want to stay backward compatible: if CONFIG_NO_HZ is set in an older config file, we want to enable CONFIG_NO_HZ_IDLE by default. But we can't afford both at the same time or we run into a circular dependency: 1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select CONFIG_NO_HZ 2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE We might be able to support that from Kconfig/Kbuild but it may not be wise to introduce such a confusing behaviour. So to solve this, create a new CONFIG_NO_HZ_COMMON option which gathers the common code between idle and full dynticks (that common code for now is simply the idle dynticks code) and select it from their referring Kconfig. Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ to it for backward compatibility. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
cfea7d7e |
|
07-Feb-2013 |
Rado Vrbovsky <rvrbovsk@redhat.com> |
tick: Change log level of NOHZ: local_softirq_pending message The "NOHZ: local_softirq_pending" message is a largely informational message. This makes extra work for customers that have a policy of investigating all kernel log messages logged at <= KERN_ERR log level. This patch sets the message to a different log level. [ tglx: Use pr_warn() ] Signed-off-by: Rado Vrbovsky <rvrbovsk@redhat.com> Cc: Don Zickus <dzickus@redhat.com> Link: http://lkml.kernel.org/r/2037057938.893524.1360345050772.JavaMail.root@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
a382bf93 |
|
18-Dec-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Assign timekeeping duty to a CPU outside the full dynticks range This way the full nohz CPUs can safely run with the tick stopped with a guarantee that somebody else is taking care of the jiffies and GTOD progression. Once the duty is attributed to a CPU, it won't change. Also that CPU can't enter into dyntick idle mode or be hot unplugged. This may later be improved from a power consumption POV. At least we should be able to share the duty amongst all CPUs outside the full dynticks range. Then the duty could even be shared with full dynticks CPUs when those can't stop their tick for any reason. But let's start with that very simple approach first. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> [fix have_nohz_full_mask offcase] Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
#
a831881b |
|
18-Dec-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Basic full dynticks interface For extreme usecases such as Real Time or HPC, having the ability to shutdown the tick when a single task runs on a CPU is a desired feature: * Reducing the amount of interrupts improves throughput for CPU-bound tasks. The CPU is less distracted from its real job, from an execution time and from the cache point of views. * This also improve latency response as we have less critical sections. Start with introducing a very simple interface to define full dynticks CPU: use a boot time option defined cpumask through the "nohz_extended=" kernel parameter. CPUs that are part of this range will have their tick shutdown whenever possible: provided they run a single task and they don't do kernel activity that require the periodic tick. These details will be later documented in Documentation/* An online CPU must be kept outside this range to handle the timekeeping. Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@linaro.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
af7bdbaf |
|
21-Feb-2013 |
Thomas Gleixner <tglx@linutronix.de> |
Revert "nohz: Make tick_nohz_irq_exit() irq safe" This reverts commit 351429b2e62b6545bb10c756686393f29ba268a1. The extra local_irq_save() is not longer needed as the call site now always calls with interrupts disabled. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Linus Torvalds <torvalds@linuxfoundation.org>
|
#
e5ab012c |
|
20-Feb-2013 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Make tick_nohz_irq_exit() irq safe As it stands, irq_exit() may or may not be called with irqs disabled, depending on __ARCH_IRQ_EXIT_IRQS_DISABLED that the arch can define. It makes tick_nohz_irq_exit() unsafe. For example two interrupts can race in tick_nohz_stop_sched_tick(): the inner most one computes the expiring time on top of the timer list, then it's interrupted right before reprogramming the clock. The new interrupt enqueues a new timer list timer, it reprogram the clock to take it into account and it exits. The CPUs resumes the inner most interrupt and performs the clock reprogramming without considering the new timer list timer. This regression has been introduced by: 280f06774afedf849f0b34248ed6aff57d0f6908 ("nohz: Separate out irq exit and idle loop dyntick logic") Let's fix it right now with the appropriate protections. A saner long term solution will be to remove __ARCH_IRQ_EXIT_IRQS_DISABLED and mandate that irq_exit() is called with interrupts disabled. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linuxfoundation.org> Cc: <stable@vger.kernel.org> #v3.2+ Link: http://lkml.kernel.org/r/1361373336-11337-1-git-send-email-fweisbec@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
3f4724ea |
|
16-Jul-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
cputime: Allow dynamic switch between tick/virtual based cputime accounting Allow to dynamically switch between tick and virtual based cputime accounting. This way we can provide a kind of "on-demand" virtual based cputime accounting. In this mode, the kernel relies on the context tracking subsystem to dynamically probe on kernel boundaries. This is in preparation for being able to stop the timer tick in more places than just the idle state. Doing so will depend on CONFIG_VIRT_CPU_ACCOUNTING_GEN which makes it possible to account the cputime without the tick by hooking on kernel/user boundaries. Depending whether the tick is stopped or not, we can switch between tick and vtime based accounting anytime in order to minimize the overhead associated to user hooks. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Li Zhong <zhong@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
4dbd2771 |
|
04-Jan-2013 |
Jacob Pan <jacob.jun.pan@linux.intel.com> |
tick: export nohz tick idle symbols for module use Allow drivers such as intel_powerclamp to use these apis for turning on/off ticks during idle. Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
#
74876a98 |
|
12-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
printk: Wake up klogd using irq_work klogd is woken up asynchronously from the tick in order to do it safely. However if printk is called when the tick is stopped, the reader won't be woken up until the next interrupt, which might not fire for a while. As a result, the user may miss some message. To fix this, lets implement the printk tick using a lazy irq work. This subsystem takes care of the timer tick state and can fix up accordingly. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
|
#
00b42959 |
|
07-Nov-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
irq_work: Don't stop the tick with pending works Don't stop the tick if we have pending irq works on the queue, otherwise if the arch can't raise self-IPIs, we may not find an opportunity to execute the pending works for a while. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
|
#
33a5f626 |
|
11-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Add API to check tick state We need some quick way to check if the CPU has stopped its tick. This will be useful to implement the printk tick using the irq work subsystem. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
|
#
69a37bea |
|
25-Oct-2012 |
Youquan Song <youquan.song@intel.com> |
cpuidle: Quickly notice prediction failure for repeat mode The prediction for future is difficult and when the cpuidle governor prediction fails and govenor possibly choose the shallower C-state than it should. How to quickly notice and find the failure becomes important for power saving. cpuidle menu governor has a method to predict the repeat pattern if there are 8 C-states residency which are continuous and the same or very close, so it will predict the next C-states residency will keep same residency time. There is a real case that turbostat utility (tools/power/x86/turbostat) at kernel 3.3 or early. turbostat utility will read 10 registers one by one at Sandybridge, so it will generate 10 IPIs to wake up idle CPUs. So cpuidle menu governor will predict it is repeat mode and there is another IPI wake up idle CPU soon, so it keeps idle CPU stay at C1 state even though CPU is totally idle. However, in the turbostat, following 10 registers reading is sleep 5 seconds by default, so the idle CPU will keep at C1 for a long time though it is idle until break event occurs. In a idle Sandybridge system, run "./turbostat -v", we will notice that deep C-state dangles between "70% ~ 99%". After patched the kernel, we will notice deep C-state stays at >99.98%. In the patch, a timer is added when menu governor detects a repeat mode and choose a shallow C-state. The timer is set to a time out value that greater than predicted time, and we conclude repeat mode prediction failure if timer is triggered. When repeat mode happens as expected, the timer is not triggered and CPU waken up from C-states and it will cancel the timer initiatively. When repeat mode does not happen, the timer will be time out and menu governor will quickly notice that the repeat mode prediction fails and then re-evaluates deeper C-states possibility. Below is another case which will clearly show the patch much benefit: #include <stdlib.h> #include <stdio.h> #include <unistd.h> #include <signal.h> #include <sys/time.h> #include <time.h> #include <pthread.h> volatile int * shutdown; volatile long * count; int delay = 20; int loop = 8; void usage(void) { fprintf(stderr, "Usage: idle_predict [options]\n" " --help -h Print this help\n" " --thread -n Thread number\n" " --loop -l Loop times in shallow Cstate\n" " --delay -t Sleep time (uS)in shallow Cstate\n"); } void *simple_loop() { int idle_num = 1; while (!(*shutdown)) { *count = *count + 1; if (idle_num % loop) usleep(delay); else { /* sleep 1 second */ usleep(1000000); idle_num = 0; } idle_num++; } } static void sighand(int sig) { *shutdown = 1; } int main(int argc, char *argv[]) { sigset_t sigset; int signum = SIGALRM; int i, c, er = 0, thread_num = 8; pthread_t pt[1024]; static char optstr[] = "n:l:t:h:"; while ((c = getopt(argc, argv, optstr)) != EOF) switch (c) { case 'n': thread_num = atoi(optarg); break; case 'l': loop = atoi(optarg); break; case 't': delay = atoi(optarg); break; case 'h': default: usage(); exit(1); } printf("thread=%d,loop=%d,delay=%d\n",thread_num,loop,delay); count = malloc(sizeof(long)); shutdown = malloc(sizeof(int)); *count = 0; *shutdown = 0; sigemptyset(&sigset); sigaddset(&sigset, signum); sigprocmask (SIG_BLOCK, &sigset, NULL); signal(SIGINT, sighand); signal(SIGTERM, sighand); for(i = 0; i < thread_num ; i++) pthread_create(&pt[i], NULL, simple_loop, NULL); for (i = 0; i < thread_num; i++) pthread_join(pt[i], NULL); exit(0); } Get powertop V2 from git://github.com/fenrus75/powertop, build powertop. After build the above test application, then run it. Test plaform can be Intel Sandybridge or other recent platforms. #./idle_predict -l 10 & #./powertop We will find that deep C-state will dangle between 40%~100% and much time spent on C1 state. It is because menu governor wrongly predict that repeat mode is kept, so it will choose the C1 shallow C-state even though it has chance to sleep 1 second in deep C-state. While after patched the kernel, we find that deep C-state will keep >99.6%. Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
#
d6ad4187 |
|
28-Feb-2012 |
John Stultz <john.stultz@linaro.org> |
time: Kill xtime_lock, replacing it with jiffies_lock Now that timekeeping is protected by its own locks, rename the xtime_lock to jifffies_lock to better describe what it protects. CC: Thomas Gleixner <tglx@linutronix.de> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Richard Cochran <richardcochran@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org>
|
#
b8f61116 |
|
24-Oct-2012 |
Chuansheng Liu <chuansheng.liu@intel.com> |
tick: Correct the comments for tick_sched_timer() In the comments of function tick_sched_timer(), the sentence "timer->base->cpu_base->lock held" is not right. In function __run_hrtimer(), before call timer->function(), the cpu_base->lock has been unlocked. Signed-off-by: liu chuansheng <chuansheng.liu@intel.com> Cc: fei.li@intel.com Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1351098455.15558.1421.camel@cliu38-desktop-build Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
351f181f |
|
24-Oct-2012 |
Chuansheng Liu <chuansheng.liu@intel.com> |
timers, sched: Correct the comments for tick_sched_timer() In the comments of function tick_sched_timer(), the sentence "timer->base->cpu_base->lock held" is not right. In function __run_hrtimer(), before call timer->function(), the cpu_base->lock has been unlocked. Signed-off-by: liu chuansheng <chuansheng.liu@intel.com> Cc: fei.li@intel.com Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1351098455.15558.1421.camel@cliu38-desktop-build Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
94a57140 |
|
15-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
tick: Conditionally build nohz specific code in tick handler This optimize a bit the high res tick sched handler. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org>
|
#
9e8f559b |
|
14-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
tick: Consolidate tick handling for high and low res handlers Besides unifying code, this also adds the idle check before processing idle accounting specifics on the low res handler. This way we also generalize this part of the nohz code for !CONFIG_HIGH_RES_TIMERS to prepare for the adaptive tickless features. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org>
|
#
5bb96226 |
|
14-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
tick: Consolidate timekeeping handling code Unify the duplicated timekeeping handling code of low and high res tick sched handlers. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org>
|
#
2b17c545 |
|
03-Oct-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Fix one jiffy count too far in idle cputime When we stop the tick in idle, we save the current jiffies value in ts->idle_jiffies. This snapshot is substracted from the later value of jiffies when the tick is restarted and the resulting delta is accounted as idle cputime. This is how we handle the idle cputime accounting without the tick. But sometimes we need to schedule the next tick to some time in the future instead of completely stopping it. In this case, a tick may happen before we restart the periodic behaviour and from that tick we account one jiffy to idle cputime as usual but we also increment the ts->idle_jiffies snapshot by one so that when we compute the delta to account, we substract the one jiffy we just accounted. To prepare for stopping the tick outside idle, we introduced a check that prevents from fixing up that ts->idle_jiffies if we are not running the idle task. But we use idle_cpu() for that and this is a problem if we run the tick while another CPU remotely enqueues a ttwu to our runqueue: CPU 0: CPU 1: tick_sched_timer() { ttwu_queue_remote() if (idle_cpu(CPU 0)) ts->idle_jiffies++; } Here, idle_cpu() notes that &rq->wake_list is not empty and hence won't consider the CPU as idle. As a result, ts->idle_jiffies won't be incremented. But this is wrong because we actually account the current jiffy to idle cputime. And that jiffy won't get substracted from the nohz time delta. So in the end, this jiffy is accounted twice. Fix this by changing idle_cpu(smp_processor_id()) with is_idle_task(current). This way the jiffy is substracted correctly even if a ttwu operation is enqueued on the CPU. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> # 3.5+ Link: http://lkml.kernel.org/r/1349308004-3482-1-git-send-email-fweisbec@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
803b0eba |
|
23-Aug-2012 |
Paul E. McKenney <paulmck@kernel.org> |
time: RCU permitted to stop idle entry via softirq The can_stop_idle_tick() function complains if a softirq vector is raised too late in the idle-entry process, presumably in order to prevent dangling softirq invocations from being delayed across the full idle period, which might be indefinitely long -- and if softirq was asserted any later than the call to this function, such a delay might well happen. However, RCU needs to be able to use softirq to stop idle entry in order to be able to drain RCU callbacks from the current CPU, which in turn enables faster entry into dyntick-idle mode, which in turn reduces power consumption. Because RCU takes this action at a well-defined point in the idle-entry path, it is safe for RCU to take this approach. This commit therefore silences the error message that is sometimes produced when the going-idle CPU suddenly finds that it has an RCU_SOFTIRQ to process. The error message will continue to be issued for other softirq vectors. Reported-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
#
c1cc017c |
|
10-Sep-2012 |
Alex Shi <alex.shi@linux.alibaba.com> |
sched/nohz: Clean up select_nohz_load_balancer() There is no load_balancer to be selected now. It just sets the state of the nohz tick to stop. So rename the function, pass the 'cpu' as a parameter and then remove the useless call from tick_nohz_restart_sched_tick(). [ s/set_nohz_tick_stopped/nohz_balance_enter_idle/g s/clear_nohz_tick_stopped/nohz_balance_exit_idle/g ] Signed-off-by: Alex Shi <alex.shi@intel.com> Acked-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Venkatesh Pallipadi <venki@google.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1347261059-24747-1-git-send-email-alex.shi@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
749c8814 |
|
20-Aug-2012 |
Charles Wang <muming.wq@taobao.com> |
sched: Add missing call to calc_load_exit_idle() Azat Khuzhin reported high loadavg in Linux v3.6 After checking the upstream scheduler code, I found Peter's commit: 5167e8d5417b sched/nohz: Rewrite and fix load-avg computation -- again not fully applied, missing the call to calc_load_exit_idle(). After that idle exit in sampling window will always be calculated to non-idle, and the load will be higher than normal. This patch adds the missing call to calc_load_exit_idle(). Signed-off-by: Charles Wang <muming.wq@taobao.com> Cc: stable@kernel.org Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1345449754-27130-1-git-send-email-muming.wq@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
5167e8d5 |
|
22-Jun-2012 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched/nohz: Rewrite and fix load-avg computation -- again Thanks to Charles Wang for spotting the defects in the current code: - If we go idle during the sample window -- after sampling, we get a negative bias because we can negate our own sample. - If we wake up during the sample window we get a positive bias because we push the sample to a known active period. So rewrite the entire nohz load-avg muck once again, now adding copious documentation to the code. Reported-and-tested-by: Doug Smythies <dsmythies@telus.net> Reported-and-tested-by: Charles Wang <muming.wq@gmail.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: stable@kernel.org Link: http://lkml.kernel.org/r/1340373782.18025.74.camel@twins [ minor edits ] Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
9d2ad243 |
|
24-Jun-2012 |
Paul E. McKenney <paulmck@kernel.org> |
rcu: Make RCU_FAST_NO_HZ respect nohz= boot parameter If the nohz= boot parameter disables nohz, then RCU_FAST_NO_HZ needs to also disable itself. This commit therefore checks for tick_nohz_enabled being zero, disabling rcu_prepare_for_idle() if so. This commit assumes that tick_nohz_enabled can change at runtime: If this is not the case, then a simpler approach suffices. Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
#
84bf1bcc |
|
31-Jul-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Move next idle expiry time record into idle logic area The next idle expiry time record and idle sleeps tracking are statistics that only concern idle. Since we want the nohz APIs to become usable further idle context, let's pull up the handling of these statistics to the callers in idle. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alessio Igor Bogani <abogani@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Avi Kivity <avi@redhat.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@ti.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
5b39939a |
|
31-Jul-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Move ts->idle_calls incrementation into strict idle logic Since we want to prepare for making the nohz API to work further the idle case, we need to pull ts->idle_calls incrementation up to the callers in idle. To perform this, we split tick_nohz_stop_sched_tick() in two parts: a first one that checks if we can really stop the tick for idle, and another that actually stops it. Then from the callers in idle, we check if we can stop the tick and only then we increment idle_calls and finally relay to the nohz API that won't care about these details anymore. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alessio Igor Bogani <abogani@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Avi Kivity <avi@redhat.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@ti.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
f5d411c9 |
|
31-Jul-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Rename ts->idle_tick to ts->last_tick Now that idle and nohz logics are going to be independant each others, ts->idle_tick becomes too much a biased name to describe the field that saves the last scheduled tick on top of which we re-calculate the next tick to schedule when the timer is restarted. We want to reuse this even to stop the tick outside idle cases. So let's rename it to some more generic name: ts->last_tick. This changes a bit the timer list stat export so we need to increase its version. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alessio Igor Bogani <abogani@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Avi Kivity <avi@redhat.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@ti.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
2ac0d98f |
|
27-Jul-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Make nohz API agnostic against idle ticks cputime accounting When the timer tick fires, it accounts the new jiffy as either part of system, user or idle time. This is how we record the cputime statistics. But when the tick is stopped from the idle task, we still need to record the number of jiffies spent tickless until we restart the tick and fall back to traditional tick-based cputime accounting. To do this, we take a snapshot of jiffies when the tick is stopped and compute the difference against the new value of jiffies when the tick is restarted. Then we account this whole difference to the idle cputime. However we are preparing to be able to stop the tick from other places than idle. So this idle time accounting needs to be performed from the callers of nohz APIs, not from the nohz APIs themselves because we now want them to be agnostic against places that stop/restart tick. Therefore, we pull the tickless idle time accounting out of generic nohz helpers up to idle entry/exit callers. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alessio Igor Bogani <abogani@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Avi Kivity <avi@redhat.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@ti.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
19f5f736 |
|
27-Jul-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Separate idle sleeping time accounting from nohz logic As we plan to be able to stop the tick outside the idle task, we need to prepare for separating nohz logic from idle. As a start, this pulls the idle sleeping time accounting out of the tick stop/restart API to the callers on idle entry/exit. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alessio Igor Bogani <abogani@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Avi Kivity <avi@redhat.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Christoph Lameter <cl@linux.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Geoff Levand <geoff@infradead.org> Cc: Gilad Ben Yossef <gilad@benyossef.com> Cc: Hakan Akkan <hakanakkan@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kevin Hilman <khilman@ti.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de>
|
#
aa9b1630 |
|
10-May-2012 |
Paul E. McKenney <paulmck@kernel.org> |
rcu: Precompute RCU_FAST_NO_HZ timer offsets When a CPU is entering dyntick-idle mode, tick_nohz_stop_sched_tick() calls rcu_needs_cpu() see if RCU needs that CPU, and, if not, computes the next wakeup time based on the timer wheels. Only later, when actually entering the idle loop, rcu_prepare_for_idle() will be invoked. In some cases, rcu_prepare_for_idle() will post timers to wake the CPU back up. But all for naught: The next wakeup time for the CPU has already been computed, and posting a timer afterwards does not force that wakeup time to be recomputed. This means that rcu_prepare_for_idle()'s have no effect. This is not a problem on a busy system because something else will wake up the CPU soon enough. However, on lightly loaded systems, the CPU might stay asleep for a considerable length of time. If that CPU has a callback that the rest of the system is waiting on, the system might run very slowly or (in theory) even hang. This commit avoids this problem by having rcu_needs_cpu() give tick_nohz_stop_sched_tick() an estimate of when RCU will need the CPU to wake back up, which tick_nohz_stop_sched_tick() takes into account when programming the CPU's wakeup time. An alternative approach is for rcu_prepare_for_idle() to use hrtimers instead of normal timers, but timers are much more efficient than are hrtimers for frequently and repeatedly posting and cancelling a given timer, which is exactly what RCU_FAST_NO_HZ does. Reported-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr> Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Tested-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
|
#
5aaa0b7a |
|
17-May-2012 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched/nohz: Fix rq->cpu_load calculations some more Follow up on commit 556061b00 ("sched/nohz: Fix rq->cpu_load[] calculations") since while that fixed the busy case it regressed the mostly idle case. Add a callback from the nohz exit to also age the rq->cpu_load[] array. This closes the hole where either there was no nohz load balance pass during the nohz, or there was a 'significant' amount of idle time between the last nohz balance and the nohz exit. So we'll update unconditionally from the tick to not insert any accidental 0 load periods while busy, and we try and catch up from nohz idle balance and nohz exit. Both these are still prone to missing a jiffy, but that has always been the case. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: pjt@google.com Cc: Venkatesh Pallipadi <venki@google.com> Link: http://lkml.kernel.org/n/tip-kt0trz0apodbf84ucjfdbr1a@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
#
62cf20b3 |
|
25-May-2012 |
Thomas Gleixner <tglx@linutronix.de> |
tick: Move skew_tick option into the HIGH_RES_TIMER section commit 5307c95 (tick: Add tick skew boot option) broke the !CONFIG_HIGH_RES_TIMERS build. Move the boot option parsing into the CONFIG_HIGH_RES_TIMERS section. Reported-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mike Galbraith <mgalbraith@suse.de>
|
#
5307c955 |
|
07-May-2012 |
Mike Galbraith <mgalbraith@suse.de> |
tick: Add tick skew boot option Let the user decide whether power consumption or jitter is the more important consideration for their machines. Quoting removal commit af5ab277ded04bd9bc6b048c5a2f0e7d70ef0867: "Historically, Linux has tried to make the regular timer tick on the various CPUs not happen at the same time, to avoid contention on xtime_lock. Nowadays, with the tickless kernel, this contention no longer happens since time keeping and updating are done differently. In addition, this skew is actually hurting power consumption in a measurable way on many-core systems." Problems: - Contrary to the above, systems do encounter contention on both xtime_lock and RCU structure locks when the tick is synchronized. - Moderate sized RT systems suffer intolerable jitter due to the tick being synchronized. - SGI reports the same for their large systems. - Fully utilized systems reap no power saving benefit from skew removal, but do suffer from resulting induced lock contention. - 0209f649 rcu: limit rcu_node leaf-level fanout This patch was born to combat lock contention which testing showed to have been _induced by_ skew removal. Skew the tick, contention disappeared virtually completely. Signed-off-by: Mike Galbraith <mgalbraith@suse.de> Link: http://lkml.kernel.org/r/1336472458.21924.78.camel@marge.simpson.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
6f103929 |
|
27-Mar-2012 |
Neal Cardwell <ncardwell@google.com> |
nohz: Fix stale jiffies update in tick_nohz_restart() Fix tick_nohz_restart() to not use a stale ktime_t "now" value when calling tick_do_update_jiffies64(now). If we reach this point in the loop it means that we crossed a tick boundary since we grabbed the "now" timestamp, so at this point "now" refers to a time in the old jiffy, so using the old value for "now" is incorrect, and is likely to give us a stale jiffies value. In particular, the first time through the loop the tick_do_update_jiffies64(now) call is always a no-op, since the caller, tick_nohz_restart_sched_tick(), will have already called tick_do_update_jiffies64(now) with that "now" value. Note that tick_nohz_stop_sched_tick() already uses the correct approach: when we notice we cross a jiffy boundary, grab a new timestamp with ktime_get(), and *then* update jiffies. Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Ben Segall <bsegall@google.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1332875377-23014-1-git-send-email-ncardwell@google.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
15f827be |
|
24-Jan-2012 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Remove ts->Einidle checks before restarting the tick ts->inidle is set by tick_nohz_idle_enter() and unset by tick_nohz_idle_exit(). However these two calls are assumed to be always paired. This means that by the time we call tick_nohz_idle_exit(), ts->inidle is supposed to be always set to 1. Remove the checks for ts->inidle in tick_nohz_idle_exit(). This simplifies a bit the code and improves its debuggability (ie: ensure the call is paired with a tick_nohz_idle_enter() call). Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Reviewed-by: Yong Zhang <yong.zhang0@gmail.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: John Stultz <john.stultz@linaro.org> Cc: Ingo Molnar <mingo@elte.hu> Link: http://lkml.kernel.org/r/1327427984-23282-2-git-send-email-fweisbec@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
430ee881 |
|
01-Dec-2011 |
Michal Hocko <mhocko@suse.cz> |
nohz: Remove update_ts_time_stat from tick_nohz_start_idle There is no reason to call update_ts_time_stat from tick_nohz_start_idle anymore (after e0e37c20 sched: Eliminate the ts->idle_lastupdate field) when we updated idle_lastupdate unconditionally. We haven't set idle_active yet and do not provide last_update_time so the whole call end up being just 2 wasted branches. Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: Arjan van de Ven <arjan@linux.intel.com> Link: http://lkml.kernel.org/r/1322755222-6951-1-git-send-email-mhocko@suse.cz Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
1268fbc7 |
|
17-Nov-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Remove tick_nohz_idle_enter_norcu() / tick_nohz_idle_exit_norcu() Those two APIs were provided to optimize the calls of tick_nohz_idle_enter() and rcu_idle_enter() into a single irq disabled section. This way no interrupt happening in-between would needlessly process any RCU job. Now we are talking about an optimization for which benefits have yet to be measured. Let's start simple and completely decouple idle rcu and dyntick idle logics to simplify. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
#
2bbb6817 |
|
08-Oct-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Allow rcu extended quiescent state handling seperately from tick stop It is assumed that rcu won't be used once we switch to tickless mode and until we restart the tick. However this is not always true, as in x86-64 where we dereference the idle notifiers after the tick is stopped. To prepare for fixing this, add two new APIs: tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu(). If no use of RCU is made in the idle loop between tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch must instead call the new *_norcu() version such that the arch doesn't need to call rcu_idle_enter() and rcu_idle_exit(). Otherwise the arch must call tick_nohz_enter_idle() and tick_nohz_exit_idle() and also call explicitly: - rcu_idle_enter() after its last use of RCU before the CPU is put to sleep. - rcu_idle_exit() before the first use of RCU after the CPU is woken up. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: David Miller <davem@davemloft.net> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Mackerras <paulus@samba.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
#
280f0677 |
|
07-Oct-2011 |
Frederic Weisbecker <fweisbec@gmail.com> |
nohz: Separate out irq exit and idle loop dyntick logic The tick_nohz_stop_sched_tick() function, which tries to delay the next timer tick as long as possible, can be called from two places: - From the idle loop to start the dytick idle mode - From interrupt exit if we have interrupted the dyntick idle mode, so that we reprogram the next tick event in case the irq changed some internal state that requires this action. There are only few minor differences between both that are handled by that function, driven by the ts->inidle cpu variable and the inidle parameter. The whole guarantees that we only update the dyntick mode on irq exit if we actually interrupted the dyntick idle mode, and that we enter in RCU extended quiescent state from idle loop entry only. Split this function into: - tick_nohz_idle_enter(), which sets ts->inidle to 1, enters dynticks idle mode unconditionally if it can, and enters into RCU extended quiescent state. - tick_nohz_irq_exit() which only updates the dynticks idle mode when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called). To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed into tick_nohz_idle_exit(). This simplifies the code and micro-optimize the irq exit path (no need for local_irq_save there). This also prepares for the split between dynticks and rcu extended quiescent state logics. We'll need this split to further fix illegal uses of RCU in extended quiescent states in the idle loop. Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: David Miller <davem@davemloft.net> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Mackerras <paulus@samba.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
#
9b2e4f18 |
|
30-Sep-2011 |
Paul E. McKenney <paulmck@kernel.org> |
rcu: Track idleness independent of idle tasks Earlier versions of RCU used the scheduling-clock tick to detect idleness by checking for the idle task, but handled idleness differently for CONFIG_NO_HZ=y. But there are now a number of uses of RCU read-side critical sections in the idle task, for example, for tracing. A more fine-grained detection of idleness is therefore required. This commit presses the old dyntick-idle code into full-time service, so that rcu_idle_enter(), previously known as rcu_enter_nohz(), is always invoked at the beginning of an idle loop iteration. Similarly, rcu_idle_exit(), previously known as rcu_exit_nohz(), is always invoked at the end of an idle-loop iteration. This allows the idle task to use RCU everywhere except between consecutive rcu_idle_enter() and rcu_idle_exit() calls, in turn allowing architecture maintainers to specify exactly where in the idle loop that RCU may be used. Because some of the userspace upcall uses can result in what looks to RCU like half of an interrupt, it is not possible to expect that the irq_enter() and irq_exit() hooks will give exact counts. This patch therefore expands the ->dynticks_nesting counter to 64 bits and uses two separate bitfields to count process/idle transitions and interrupt entry/exit transitions. It is presumed that userspace upcalls do not happen in the idle loop or from usermode execution (though usermode might do a system call that results in an upcall). The counter is hard-reset on each process/idle transition, which avoids the interrupt entry/exit error from accumulating. Overflow is avoided by the 64-bitness of the ->dyntick_nesting counter. This commit also adds warnings if a non-idle task asks RCU to enter idle state (and these checks will need some adjustment before applying Frederic's OS-jitter patches (http://lkml.org/lkml/2011/10/7/246). In addition, validation of ->dynticks and ->dynticks_nesting is added. Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org>
|
#
69e1e811 |
|
01-Dec-2011 |
Suresh Siddha <suresh.b.siddha@intel.com> |
sched, nohz: Track nr_busy_cpus in the sched_group_power Introduce nr_busy_cpus in the struct sched_group_power [Not in sched_group because sched groups are duplicated for the SD_OVERLAP scheduler domain] and for each cpu that enters and exits idle, this parameter will be updated in each scheduler group of the scheduler domain that this cpu belongs to. To avoid the frequent update of this state as the cpu enters and exits idle, the update of the stat during idle exit is delayed to the first timer tick that happens after the cpu becomes busy. This is done using NOHZ_IDLE flag in the struct rq's nohz_flags. Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20111202010832.555984323@sbsiddha-desk.sc.intel.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
fc0763f5 |
|
28-Jul-2011 |
Alex Shi <alex.shi@linux.alibaba.com> |
nohz: Remove nohz_cpu_mask RCU no longer uses this global variable, nor does anyone else. This commit therefore removes this variable. This reduces memory footprint and also removes some atomic instructions and memory barriers from the dyntick-idle path. Signed-off-by: Alex Shi <alex.shi@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
#
29c158e8 |
|
23-Aug-2011 |
Heiko Carstens <hca@linux.ibm.com> |
nohz: Remove "Switched to NOHz mode" debugging messages When performing cpu hotplug tests the kernel printk log buffer gets flooded with pointless "Switched to NOHz mode..." messages. Especially when afterwards analyzing a dump this might have removed more interesting stuff out of the buffer. Assuming that switching to NOHz mode simply works just remove the printk. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Link: http://lkml.kernel.org/r/20110823112046.GB2540@osiris.boeblingen.de.ibm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
09a1d34f |
|
24-Aug-2011 |
Michal Hocko <mhocko@suse.cz> |
nohz: Make idle/iowait counter update conditional get_cpu_{idle,iowait}_time_us update idle/iowait counters unconditionally if the given CPU is in the idle loop. This doesn't work well outside of CPU governors which are singletons so nobody (except for IRQ) can race with them. We will need to use both functions from /proc/stat handler to properly handle nohz idle/iowait times. Make the update depend on a non NULL last_update_time argument. Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: Dave Jones <davej@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Link: http://lkml.kernel.org/r/11f23179472635ce52e78921d47a20216b872f23.1314172057.git.mhocko@suse.cz Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
6beea0cd |
|
24-Aug-2011 |
Michal Hocko <mhocko@suse.cz> |
nohz: Fix update_ts_time_stat idle accounting update_ts_time_stat currently updates idle time even if we are in iowait loop at the moment. The only real users of the idle counter (via get_cpu_idle_time_us) are CPU governors and they expect to get cumulative time for both idle and iowait times. The value (idle_sleeptime) is also printed to userspace by print_cpu but it prints both idle and iowait times so the idle part is misleading. Let's clean this up and fix update_ts_time_stat to account both counters properly and update consumers of idle to consider iowait time as well. If we do this we might use get_cpu_{idle,iowait}_time_us from other contexts as well and we will get expected values. Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: Dave Jones <davej@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Link: http://lkml.kernel.org/r/e9c909c221a8da402c4da07e4cd968c3218f8eb1.1314172057.git.mhocko@suse.cz Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
e2830b5c |
|
27-Jan-2011 |
Torben Hohn <torbenh@gmx.de> |
time: Make do_timer() and xtime_lock local to kernel/time/ All callers of do_timer() are converted to xtime_update(). The only users of xtime_lock are in kernel/time/. Make both local to kernel/time/ and remove them from the global header files. [ tglx: Reuse tick-internal.h instead of creating another local header file. Massaged changelog ] Signed-off-by: Torben Hohn <torbenh@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: johnstul@us.ibm.com Cc: yong.zhang0@gmail.com Cc: hch@infradead.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
2d0640b4 |
|
18-Jan-2011 |
Stephen Boyd <sboyd@codeaurora.org> |
hrtimers: Notify hrtimer users of switches to NOHZ mode When NOHZ=y and high res timers are disabled (via cmdline or Kconfig) tick_nohz_switch_to_nohz() will notify the user about switching into NOHZ mode. Nothing is printed for the case where HIGH_RES_TIMERS=y. Fix this for the HIGH_RES_TIMERS=y case by duplicating the printk from the low res NOHZ path in the high res NOHZ path. This confused me since I was thinking 'dmesg | grep -i NOHZ' would tell me if NOHZ was enabled, but if I have hrtimers there is nothing. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> LKML-Reference: <1295419594-13085-1-git-send-email-sboyd@codeaurora.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
af5ab277 |
|
27-Jul-2010 |
Arjan van de Ven <arjan@infradead.org> |
clockevents: Remove the per cpu tick skew Historically, Linux has tried to make the regular timer tick on the various CPUs not happen at the same time, to avoid contention on xtime_lock. Nowadays, with the tickless kernel, this contention no longer happens since time keeping and updating are done differently. In addition, this skew is actually hurting power consumption in a measurable way on many-core systems. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> LKML-Reference: <20100727210210.58d3118c@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
396e894d |
|
09-Jul-2010 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched: Revert nohz_ratelimit() for now Norbert reported that nohz_ratelimit() causes his laptop to burn about 4W (40%) extra. For now back out the change and see if we can adjust the power management code to make better decisions. Reported-by: Norbert Preining <preining@logic.at> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Mike Galbraith <efault@gmx.de> Cc: Arjan van de Ven <arjan@infradead.org> LKML-Reference: <new-submission> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
8c215bd3 |
|
01-Jul-2010 |
Peter Zijlstra <peterz@infradead.org> |
sched: Cure nr_iowait_cpu() users Commit 0224cf4c5e (sched: Intoduce get_cpu_iowait_time_us()) broke things by not making sure preemption was indeed disabled by the callers of nr_iowait_cpu() which took the iowait value of the current cpu. This resulted in a heap of preempt warnings. Cure this by making nr_iowait_cpu() take a cpu number and fix up the callers to pass in the right number. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Cc: Len Brown <len.brown@intel.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Jiri Slaby <jslaby@suse.cz> Cc: linux-pm@lists.linux-foundation.org LKML-Reference: <1277968037.1868.120.camel@laptop> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
3310d4d3 |
|
17-Jun-2010 |
Peter Zijlstra <peterz@infradead.org> |
nohz: Fix nohz ratelimit Chris Wedgwood reports that 39c0cbe (sched: Rate-limit nohz) causes a serial console regression, unresponsiveness, and indeed it does. The reason is that the nohz code is skipped even when the tick was already stopped before the nohz_ratelimit(cpu) condition changed. Move the nohz_ratelimit() check to the other conditions which prevent long idle sleeps. Reported-by: Chris Wedgwood <cw@f00f.org> Tested-by: Brian Bloniarz <bmb@athenacr.com> Signed-off-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg KH <gregkh@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Jef Driesen <jefdriesen@telenet.be> LKML-Reference: <1276790557.27822.516.camel@twins> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
83cd4fe2 |
|
21-May-2010 |
Venkatesh Pallipadi <venki@google.com> |
sched: Change nohz idle load balancing logic to push model In the new push model, all idle CPUs indeed go into nohz mode. There is still the concept of idle load balancer (performing the load balancing on behalf of all the idle cpu's in the system). Busy CPU kicks the nohz balancer when any of the nohz CPUs need idle load balancing. The kickee CPU does the idle load balancing on behalf of all idle CPUs instead of the normal idle balance. This addresses the below two problems with the current nohz ilb logic: * the idle load balancer continued to have periodic ticks during idle and wokeup frequently, even though it did not have any rebalancing to do on behalf of any of the idle CPUs. * On x86 and CPUs that have APIC timer stoppage on idle CPUs, this periodic wakeup can result in a periodic additional interrupt on a CPU doing the timer broadcast. Also currently we are migrating the unpinned timers from an idle to the cpu doing idle load balancing (when all the cpus in the system are idle, there is no idle load balancing cpu and timers get added to the same idle cpu where the request was made. So the existing optimization works only on semi idle system). And In semi idle system, we no longer have periodic ticks on the idle load balancer CPU. Using that cpu will add more delays to the timers than intended (as that cpu's timer base may not be uptodate wrt jiffies etc). This was causing mysterious slowdowns during boot etc. For now, in the semi idle case, use the nearest busy cpu for migrating timers from an idle cpu. This is good for power-savings anyway. Signed-off-by: Venkatesh Pallipadi <venki@google.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> LKML-Reference: <1274486981.2840.46.camel@sbs-t61.sc.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
0224cf4c |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Intoduce get_cpu_iowait_time_us() For the ondemand cpufreq governor, it is desired that the iowait time is microaccounted in a similar way as idle time is. This patch introduces the infrastructure to account and expose this information via the get_cpu_iowait_time_us() function. [akpm@linux-foundation.org: fix CONFIG_NO_HZ=n build] Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082523.284feab6@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
e0e37c20 |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Eliminate the ts->idle_lastupdate field Now that the only user of ts->idle_lastupdate is update_ts_time_stats(), the entire field can be eliminated. In update_ts_time_stats(), idle_lastupdate is first set to "now", and a few lines later, the only user is an if() statement that assigns a variable either to "now" or to ts->idle_lastupdate, which has the value of "now" at that point. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082439.2fab0b4f@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
8d63bf94 |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Fold updating of the last_update_time_info into update_ts_time_stats() This patch folds the updating of the last_update_time into the update_ts_time_stats() function, and updates the callers. This allows for further cleanups that are done in the next patch. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082403.60072967@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
8c7b09f4 |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Update the idle statistics in get_cpu_idle_time_us() Right now, get_cpu_idle_time_us() only reports the idle statistics upto the point the CPU entered last idle; not what is valid right now. This patch adds an update of the idle statistics to get_cpu_idle_time_us(), so that calling this function always returns statistics that are accurate at the point of the call. This includes resetting the start of the idle time for accounting purposes to avoid double accounting. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082323.2d2f1945@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
595aac48 |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Introduce a function to update the idle statistics Currently, two places update the idle statistics (and more to come later in this series). This patch creates a helper function for updating these statistics. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082245.163e67ed@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
b1f724c3 |
|
09-May-2010 |
Arjan van de Ven <arjan@linux.intel.com> |
sched: Add a comment to get_cpu_idle_time_us() The exported function get_cpu_idle_time_us() has no comment describing it; add a kerneldoc comment Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: davej@redhat.com LKML-Reference: <20100509082208.7cb721f0@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
39c0cbe2 |
|
11-Mar-2010 |
Mike Galbraith <efault@gmx.de> |
sched: Rate-limit nohz Entering nohz code on every micro-idle is costing ~10% throughput for netperf TCP_RR when scheduling cross-cpu. Rate limiting entry fixes this, but raises ticks a bit. On my Q6600, an idle box goes from ~85 interrupts/sec to 128. The higher the context switch rate, the more nohz entry costs. With this patch and some cycle recovery patches in my tree, max cross cpu context switch rate is improved by ~16%, a large portion of which of which is this ratelimiting. Signed-off-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> LKML-Reference: <1268301003.6785.28.camel@marge.simson.net> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
27185016 |
|
12-Nov-2009 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: Track last do_timer() cpu The previous patch which limits the sleep time to the maximum deferment time of the time keeping clocksource has some limitations on SMP machines: if all CPUs are idle then for all CPUs the maximum sleep time is limited. Solve this by keeping track of which cpu had the do_timer() duty assigned last and limit the sleep time only for this cpu. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> LKML-Reference: <new-submission> Cc: Jon Hunter <jon-hunter@ti.com> Cc: John Stultz <johnstul@us.ibm.com>
|
#
98962465 |
|
17-Aug-2009 |
Jon Hunter <jon-hunter@ti.com> |
nohz: Prevent clocksource wrapping during idle The dynamic tick allows the kernel to sleep for periods longer than a single tick, but it does not limit the sleep time currently. In the worst case the kernel could sleep longer than the wrap around time of the time keeping clock source which would result in losing track of time. Prevent this by limiting it to the safe maximum sleep time of the current time keeping clock source. The value is calculated when the clock source is registered. [ tglx: simplified the code a bit and massaged the commit msg ] Signed-off-by: Jon Hunter <jon-hunter@ti.com> Cc: John Stultz <johnstul@us.ibm.com> LKML-Reference: <1250617512-23567-2-git-send-email-jon-hunter@ti.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
529eaccd |
|
13-Nov-2009 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: Type cast printk argument On some archs local_softirq_pending() has a data type of unsigned long on others its unsigned int. Type cast it to (unsigned int) in the printk to avoid the compiler warning. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> LKML-Reference: <new-submission>
|
#
3c5d92a0 |
|
29-Sep-2009 |
Martin Schwidefsky <schwidefsky@de.ibm.com> |
nohz: Introduce arch_needs_cpu Allow the architecture to request a normal jiffy tick when the system goes idle and tick_nohz_stop_sched_tick is called . On s390 the hook is used to prevent the system going fully idle if there has been an interrupt other than a clock comparator interrupt since the last wakeup. On s390 the HiperSockets response time for 1 connection ping-pong goes down from 42 to 34 microseconds. The CPU cost decreases by 27%. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> LKML-Reference: <20090929122533.402715150@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
eed3b9cf |
|
29-Sep-2009 |
Martin Schwidefsky <schwidefsky@de.ibm.com> |
nohz: Reuse ktime in sub-functions of tick_check_idle. On a system with NOHZ=y tick_check_idle calls tick_nohz_stop_idle and tick_nohz_update_jiffies. Given the right conditions (ts->idle_active and/or ts->tick_stopped) both function get a time stamp with ktime_get. The same time stamp can be reused if both function require one. On s390 this change has the additional benefit that gcc inlines the tick_nohz_stop_idle function into tick_check_idle. The number of instructions to execute tick_check_idle drops from 225 to 144 (without the ktime_get optimization it is 367 vs 215 instructions). before: 0) | tick_check_idle() { 0) | tick_nohz_stop_idle() { 0) | ktime_get() { 0) | read_tod_clock() { 0) 0.601 us | } 0) 1.765 us | } 0) 3.047 us | } 0) | ktime_get() { 0) | read_tod_clock() { 0) 0.570 us | } 0) 1.727 us | } 0) | tick_do_update_jiffies64() { 0) 0.609 us | } 0) 8.055 us | } after: 0) | tick_check_idle() { 0) | ktime_get() { 0) | read_tod_clock() { 0) 0.617 us | } 0) 1.773 us | } 0) | tick_do_update_jiffies64() { 0) 0.593 us | } 0) 4.477 us | } Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: john stultz <johnstul@us.ibm.com> LKML-Reference: <20090929122533.206589318@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
fdc6f192 |
|
07-Oct-2009 |
Eero Nurkkala <ext-eero.nurkkala@nokia.com> |
NOHZ: update idle state also when NOHZ is inactive Commit f2e21c9610991e95621a81407cdbab881226419b had unfortunate side effects with cpufreq governors on some systems. If the system did not switch into NOHZ mode ts->inidle is not set when tick_nohz_stop_sched_tick() is called from the idle routine. Therefor all subsequent calls from irq_exit() to tick_nohz_stop_sched_tick() fail to call tick_nohz_start_idle(). This results in bogus idle accounting information which is passed to cpufreq governors. Set the inidle flag unconditionally of the NOHZ active state to keep the idle time accounting correct in any case. [ tglx: Added comment and tweaked the changelog ] Reported-by: Steven Noonan <steven@uplinklabs.net> Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Cc: Rik van Riel <riel@redhat.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Greg KH <greg@kroah.com> Cc: Steven Noonan <steven@uplinklabs.net> Cc: stable@kernel.org LKML-Reference: <1254907901.30157.93.camel@eenurkka-desktop> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
f2e21c96 |
|
25-May-2009 |
Eero Nurkkala <ext-eero.nurkkala@nokia.com> |
NOHZ: Properly feed cpufreq ondemand governor A call from irq_exit() may occasionally pause the timing info for cpufreq ondemand governor. This results in the cpufreq ondemand governor to fail to calculate the system load properly. Thus, relocate the checks for this particular case to keep the governor always functional. Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com> Reported-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
5c333864 |
|
15-Apr-2009 |
Arun R Bharadwaj <arun@linux.vnet.ibm.com> |
timers: Identifying the existing pinned timers * Arun R Bharadwaj <arun@linux.vnet.ibm.com> [2009-04-16 12:11:36]: The following pinned hrtimers have been identified and marked: 1)sched_rt_period_timer 2)tick_sched_timer 3)stack_trace_timer_fn [ tglx: fixup the hrtimer pinned mode ] Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
934d96ea |
|
14-Jan-2009 |
Jaswinder Singh Rajput <jaswinder@infradead.org> |
time-sched.c: tick_nohz_update_jiffies should be static Impact: cleanup, reduce kernel size a bit, avoid sparse warning Fixes sparse warning: kernel/time/tick-sched.c:137:6: warning: symbol 'tick_nohz_update_jiffies' was not declared. Should it be static? Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
79741dd3 |
|
31-Dec-2008 |
Martin Schwidefsky <schwidefsky@de.ibm.com> |
[PATCH] idle cputime accounting The cpu time spent by the idle process actually doing something is currently accounted as idle time. This is plain wrong, the architectures that support VIRT_CPU_ACCOUNTING=y can do better: distinguish between the time spent doing nothing and the time spent by idle doing work. The first is accounted with account_idle_time and the second with account_system_time. The architectures that use the account_xxx_time interface directly and not the account_xxx_ticks interface now need to do the check for the idle process in their arch code. In particular to improve the system vs true idle time accounting the arch code needs to measure the true idle time instead of just testing for the idle process. To improve the tick based accounting as well we would need an architecture primitive that can tell us if the pt_regs of the interrupted context points to the magic instruction that halts the cpu. In addition idle time is no more added to the stime of the idle process. This field now contains the system time of the idle process as it should be. On systems without VIRT_CPU_ACCOUNTING this will always be zero as every tick that occurs while idle is running will be accounted as idle time. This patch contains the necessary common code changes to be able to distinguish idle system time and true idle time. The architectures with support for VIRT_CPU_ACCOUNTING need some changes to exploit this. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
#
457533a7 |
|
31-Dec-2008 |
Martin Schwidefsky <schwidefsky@de.ibm.com> |
[PATCH] fix scaled & unscaled cputime accounting The utimescaled / stimescaled fields in the task structure and the global cpustat should be set on all architectures. On s390 the calls to account_user_time_scaled and account_system_time_scaled never have been added. In addition system time that is accounted as guest time to the user time of a process is accounted to the scaled system time instead of the scaled user time. To fix the bugs and to prevent future forgetfulness this patch merges account_system_time_scaled into account_system_time and account_user_time_scaled into account_user_time. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Chris Wright <chrisw@sous-sol.org> Cc: Michael Neuling <mikey@neuling.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
#
00147449 |
|
01-Dec-2008 |
Woodruff, Richard <r-woodruff2@ti.com> |
nohz: suppress needless timer reprogramming In my device I get many interrupts from a high speed USB device in a very short period of time. The system spends a lot of time reprogramming the hardware timer which is in a slower timing domain as compared to the CPU. This results in the CPU spending a huge amount of time waiting for the timer posting to be done. All of this reprogramming is useless as the wake up time has not changed. As measured using ETM trace this drops my reprogramming penalty from almost 60% CPU load down to 15% during high interrupt rate. I can send traces to show this. Suppress setting of duplicate timer event when timer already stopped. Timer programming can be very costly and can result in long cpu stall/wait times. [akpm@linux-foundation.org: coding-style fixes] [tglx@linutronix.de: move the check to the right place and avoid raising the softirq for nothing] Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Cc: johnstul@us.ibm.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
fa116ea3 |
|
11-Dec-2008 |
Heiko Carstens <hca@linux.ibm.com> |
nohz: no softirq pending warnings for offline cpus Impact: remove false positive warning After a cpu was taken down during cpu hotplug (read: disabled for interrupts) it still might have pending softirqs. However take_cpu_down makes sure that the idle task will run next instead of ksoftirqd on the taken down cpu. The idle task will call tick_nohz_stop_sched_tick which might warn about pending softirqs just before the cpu kills itself completely. However the pending softirqs on the dead cpu aren't a problem because they will be moved to an online cpu during CPU_DEAD handling. So make sure we warn only for online cpus. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
ca109491 |
|
24-Nov-2008 |
Peter Zijlstra <peterz@infradead.org> |
hrtimer: removing all ur callback modes Impact: cleanup, move all hrtimer processing into hardirq context This is an attempt at removing some of the hrtimer complexity by reducing the number of callback modes to 1. This means that all hrtimer callback functions will be ran from HARD-irq context. I went through all the 30 odd hrtimer callback functions in the kernel and saw only one that I'm not quite sure of, which is the one in net/can/bcm.c - hence I'm CC-ing the folks responsible for that code. Furthermore, the hrtimer core now calls callbacks directly with IRQs disabled in case you try to enqueue an expired timer. If this timer is a periodic timer (which should use hrtimer_forward() to advance its time) then it might be possible to end up in an inf. recursive loop due to the fact that hrtimer_forward() doesn't round up to the next timer granularity, and therefore keeps on calling the callback - obviously this needs a fix. Aside from that, this seems to compile and actually boot on my dual core test box - although I'm sure there are some bugs in, me not hitting any makes me certain :-) Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
6a7b3dc3 |
|
24-Nov-2008 |
Rusty Russell <rusty@rustcorp.com.au> |
sched: convert nohz_cpu_mask to cpumask_var_t. Impact: (future) size reduction for large NR_CPUS. Dynamically allocating cpumasks (when CONFIG_CPUMASK_OFFSTACK) saves space for small nr_cpu_ids but big CONFIG_NR_CPUS. cpumask_var_t is just a struct cpumask for !CONFIG_CPUMASK_OFFSTACK. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
ae99286b |
|
10-Nov-2008 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: disable tick_nohz_kick_tick() for now Impact: nohz powersavings and wakeup regression commit fb02fbc14d17837b4b7b02dbb36142c16a7bf208 (NOHZ: restart tick device from irq_enter()) causes a serious wakeup regression. While the patch is correct it does not take into account that spurious wakeups happen on x86. A fix for this issue is available, but we just revert to the .27 behaviour and let long running softirqs screw themself. Disable it for now. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
c4bd822e |
|
21-Oct-2008 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: fix thinko in the timer restart code path commit fb02fbc14d17837b4b7b02dbb36142c16a7bf208 (NOHZ: restart tick device from irq_enter()) solves the problem of stale jiffies when long running softirqs happen in a long idle sleep period, but it has a major thinko in it: When the interrupt which came in _is_ the timer interrupt which should expire ts->sched_timer then we cancel and rearm the timer _before_ it gets expired in hrtimer_interrupt() to the next period. That means the call back function is not called. This game can go on for ever :( Prevent this by making sure to only rearm the timer when the expiry time is more than one tick_period away. Otherwise keep it running as it is either already expired or will expiry at the right point to update jiffies. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Venkatesch Pallipadi <venkatesh.pallipadi@intel.com>
|
#
fb02fbc1 |
|
17-Oct-2008 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: restart tick device from irq_enter() We did not restart the tick device from irq_enter() to avoid double reprogramming and extra events in the return immediate to idle case. But long lasting softirqs can lead to a situation where jiffies become stale: idle() tick stopped (reprogrammed to next pending timer) halt() interrupt jiffies updated from irq_enter() interrupt handler softirq function 1 runs 20ms softirq function 2 arms a 10ms timer with a stale jiffies value jiffies updated from irq_exit() timer wheel has now an already expired timer (the one added in function 2) timer fires and timer softirq runs This was discovered when debugging a timer problem which happend only when the ath5k driver is active. The debugging proved that there is a softirq function running for more than 20ms, which is a bug by itself. To solve this we restart the tick timer right from irq_enter(), but do not go through the other functions which are necessary to return from idle when need_resched() is set. Reported-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Elias Oltmanns <eo@nebensachen.de>
|
#
c34bec5a |
|
17-Oct-2008 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: split tick_nohz_restart_sched_tick() Split out the clock event device reprogramming. Preparatory patch. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
719254fa |
|
17-Oct-2008 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: unify the nohz function calls in irq_enter() We have two separate nohz function calls in irq_enter() for no good reason. Just call a single NOHZ function from irq_enter() and call the bits in the tick code. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
8083e4ad |
|
04-Aug-2008 |
venkatesh.pallipadi@intel.com <venkatesh.pallipadi@intel.com> |
[CPUFREQ][5/6] cpufreq: Changes to get_cpu_idle_time_us(), used by ondemand governor export get_cpu_idle_time_us() for it to be used in ondemand governor. Last update time can be current time when the CPU is currently non-idle, accounting for the busy time since last idle. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Dave Jones <davej@redhat.com>
|
#
ccc7dadf |
|
29-Sep-2008 |
Thomas Gleixner <tglx@linutronix.de> |
hrtimer: prevent migration of per CPU hrtimers Impact: per CPU hrtimers can be migrated from a dead CPU The hrtimer code has no knowledge about per CPU timers, but we need to prevent the migration of such timers and warn when such a timer is active at migration time. Explicitely mark the timers as per CPU and use a more understandable mode descriptor for the interrupts safe unlocked callback mode, which is used by hrtimer_sleeper and the scheduler code. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
49d670fb |
|
22-Sep-2008 |
Thomas Gleixner <tglx@linutronix.de> |
clockevents: prevent stale tick_next_period for onlining CPUs Impact: possible hang on CPU onlining in timer one shot mode. The tick_next_period variable is only used during boot on nohz/highres enabled systems, but for CPU onlining it needs to be maintained when the per cpu clock events device operates in one shot mode. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
6441402b |
|
22-Sep-2008 |
Thomas Gleixner <tglx@linutronix.de> |
clockevents: prevent cpu online to interfere with nohz Impact: rare hang which can be triggered on CPU online. tick_do_timer_cpu keeps track of the CPU which updates jiffies via do_timer. The value -1 is used to signal, that currently no CPU is doing this. There are two cases, where the variable can have this state: boot: necessary for systems where the boot cpu id can be != 0 nohz long idle sleep: When the CPU which did the jiffies update last goes into a long idle sleep it drops the update jiffies duty so another CPU which is not idle can pick it up and keep jiffies going. Using the same value for both situations is wrong, as the CPU online code can see the -1 state when the timer of the newly onlined CPU is setup. The setup for a newly onlined CPU goes through periodic mode and can pick up the do_timer duty without being aware of the nohz / highres mode of the already running system. Use two separate states and make them constants to avoid magic numbers confusion. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
cc584b21 |
|
01-Sep-2008 |
Arjan van de Ven <arjan@linux.intel.com> |
hrtimer: convert kernel/* to the new hrtimer apis In order to be able to do range hrtimers we need to use accessor functions to the "expire" member of the hrtimer struct. This patch converts kernel/* to these accessors. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
|
#
56c7426b |
|
01-Sep-2008 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched_clock: fix NOHZ interaction If HLT stops the TSC, we'll fail to account idle time, thereby inflating the actual process times. Fix this by re-calibrating the clock against GTOD when leaving nohz mode. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Tested-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
3c4fbe5e |
|
20-Aug-2008 |
Miao Xie <miaox@cn.fujitsu.com> |
nohz: fix wrong event handler after online an offlined cpu On the tickless system(CONFIG_NO_HZ=y and CONFIG_HIGH_RES_TIMERS=n), after I made an offlined cpu online, I found this cpu's event handler was tick_handle_periodic, not tick_nohz_handler. After debuging, I found this bug was caused by the wrong tick mode. the tick mode is not changed to NOHZ_MODE_INACTIVE when the cpu is offline. This patch fixes this bug. Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
b845b517 |
|
08-Aug-2008 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
printk: robustify printk Avoid deadlocks against rq->lock and xtime_lock by deferring the klogd wakeup by polling from the timer tick. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
e4e4e534 |
|
14-Apr-2008 |
Ingo Molnar <mingo@elte.hu> |
sched clock: revert various sched_clock() changes Found an interactivity problem on a quad core test-system - simple CPU loops would occasionally delay the system un an unacceptable way. After much debugging with Peter Zijlstra it turned out that the problem is caused by the string of sched_clock() changes - they caused the CPU clock to jump backwards a bit - which confuses the scheduler arithmetics. (which is unsigned for performance reasons) So revert: # c300ba2: sched_clock: and multiplier for TSC to gtod drift # c0c8773: sched_clock: only update deltas with local reads. # af52a90: sched_clock: stop maximum check on NO HZ # f7cce27: sched_clock: widen the max and min time This solves the interactivity problems. Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Mike Galbraith <efault@gmx.de>
|
#
b8f8c3cf |
|
18-Jul-2008 |
Thomas Gleixner <tglx@linutronix.de> |
nohz: prevent tick stop outside of the idle loop Jack Ren and Eric Miao tracked down the following long standing problem in the NOHZ code: scheduler switch to idle task enable interrupts Window starts here ----> interrupt happens (does not set NEED_RESCHED) irq_exit() stops the tick ----> interrupt happens (does set NEED_RESCHED) return from schedule() cpu_idle(): preempt_disable(); Window ends here The interrupts can happen at any point inside the race window. The first interrupt stops the tick, the second one causes the scheduler to rerun and switch away from idle again and we end up with the tick disabled. The fact that it needs two interrupts where the first one does not set NEED_RESCHED and the second one does made the bug obscure and extremly hard to reproduce and analyse. Kudos to Jack and Eric. Solution: Limit the NOHZ functionality to the idle loop to make sure that we can not run into such a situation ever again. cpu_idle() { preempt_disable(); while(1) { tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we are in the idle loop while (!need_resched()) halt(); tick_nohz_restart_sched_tick(); <- disables NOHZ mode preempt_enable_no_resched(); schedule(); preempt_disable(); } } In hindsight we should have done this forever, but ... /me grabs a large brown paperbag. Debugged-by: Jack Ren <jack.ren@marvell.com>, Debugged-by: eric miao <eric.y.miao@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
af52a90a |
|
07-Jul-2008 |
Steven Rostedt <rostedt@goodmis.org> |
sched_clock: stop maximum check on NO HZ Working with ftrace I would get large jumps of 11 millisecs or more with the clock tracer. This killed the latencing timings of ftrace and also caused the irqoff self tests to fail. What was happening is with NO_HZ the idle would stop the jiffy counter and before the jiffy counter was updated the sched_clock would have a bad delta jiffies to compare with the gtod with the maximum. The jiffies would stop and the last sched_tick would record the last gtod. On wakeup, the sched clock update would compare the gtod + delta jiffies (which would be zero) and compare it to the TSC. The TSC would have correctly (with a stable TSC) moved forward several jiffies. But because the jiffies has not been updated yet the clock would be prevented from moving forward because it would appear that the TSC jumped too far ahead. The clock would then virtually stop, until the jiffies are updated. Then the next sched clock update would see that the clock was very much behind since the delta jiffies is now correct. This would then jump the clock forward by several jiffies. This caused ftrace to report several milliseconds of interrupts off latency at every resume from NO_HZ idle. This patch adds hooks into the nohz code to disable the checking of the maximum clock update when nohz is in effect. It resumes the max check when nohz has updated the jiffies again. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Cc: Steven Rostedt <srostedt@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
857f3fd7 |
|
11-Jul-2008 |
Heiko Carstens <hca@linux.ibm.com> |
nohz: don't stop idle tick if softirqs are pending. In case a cpu goes idle but softirqs are pending only an error message is printed to the console. It may take a very long time until the pending softirqs will finally be executed. Worst case would be a hanging system. With this patch the timer tick just continues and the softirqs will be executed after the next interrupt. Still a delay but better than a hanging system. Currently we have at least two device drivers on s390 which under certain circumstances schedule a tasklet from process context. This is a reason why we can end up with pending softirqs when going idle. Fixing these drivers seems to be non-trivial. However there is no question that the drivers should be fixed. This patch shouldn't be considered as a bug fix. It just is intended to keep a system running even if device drivers are buggy. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Jan Glauber <jan.glauber@de.ibm.com> Cc: Stefan Weinhuber <wein@de.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
7a14ce1d |
|
12-May-2008 |
Ingo Molnar <mingo@elte.hu> |
nohz: reduce jiffies polling overhead Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
02ff3755 |
|
12-May-2008 |
Ingo Molnar <mingo@elte.hu> |
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds Fix (probably theoretical only) rq->clock update bug: in tick_nohz_update_jiffies() [which is called on all irq entry on all cpus where the irq entry hits an idle cpu] we call touch_softlockup_watchdog() before we update jiffies. That works fine most of the time when idle timeouts are within 60 seconds. But when an idle timeout is beyond 60 seconds, jiffies is updated with a jump of more than 60 seconds, which causes a jump in cpu-clock of more than 60 seconds, triggering a false positive. Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
126e01bf |
|
24-Apr-2008 |
Ingo Molnar <mingo@elte.hu> |
softlockup: fix NOHZ wakeup David Miller reported: |---------------> the following commit: | commit 27ec4407790d075c325e1f4da0a19c56953cce23 | Author: Ingo Molnar <mingo@elte.hu> | Date: Thu Feb 28 21:00:21 2008 +0100 | | sched: make cpu_clock() globally synchronous | | Alexey Zaytsev reported (and bisected) that the introduction of | cpu_clock() in printk made the timestamps jump back and forth. | | Make cpu_clock() more reliable while still keeping it fast when it's | called frequently. | | Signed-off-by: Ingo Molnar <mingo@elte.hu> causes watchdog triggers when a cpu exits NOHZ state when it has been there for >= the soft lockup threshold, for example here are some messages from a 128 cpu Niagara2 box: [ 168.106406] BUG: soft lockup - CPU#11 stuck for 128s! [dd:3239] [ 168.989592] BUG: soft lockup - CPU#21 stuck for 86s! [swapper:0] [ 168.999587] BUG: soft lockup - CPU#29 stuck for 91s! [make:4511] [ 168.999615] BUG: soft lockup - CPU#2 stuck for 85s! [swapper:0] [ 169.020514] BUG: soft lockup - CPU#37 stuck for 91s! [swapper:0] [ 169.020514] BUG: soft lockup - CPU#45 stuck for 91s! [sh:4515] [ 169.020515] BUG: soft lockup - CPU#69 stuck for 92s! [swapper:0] [ 169.020515] BUG: soft lockup - CPU#77 stuck for 92s! [swapper:0] [ 169.020515] BUG: soft lockup - CPU#61 stuck for 92s! [swapper:0] [ 169.112554] BUG: soft lockup - CPU#85 stuck for 92s! [swapper:0] [ 169.112554] BUG: soft lockup - CPU#101 stuck for 92s! [swapper:0] [ 169.112554] BUG: soft lockup - CPU#109 stuck for 92s! [swapper:0] [ 169.112554] BUG: soft lockup - CPU#117 stuck for 92s! [swapper:0] [ 169.171483] BUG: soft lockup - CPU#40 stuck for 80s! [dd:3239] [ 169.331483] BUG: soft lockup - CPU#13 stuck for 86s! [swapper:0] [ 169.351500] BUG: soft lockup - CPU#43 stuck for 101s! [dd:3239] [ 169.531482] BUG: soft lockup - CPU#9 stuck for 129s! [mkdir:4565] [ 169.595754] BUG: soft lockup - CPU#20 stuck for 93s! [swapper:0] [ 169.626787] BUG: soft lockup - CPU#52 stuck for 93s! [swapper:0] [ 169.626787] BUG: soft lockup - CPU#84 stuck for 92s! [swapper:0] [ 169.636812] BUG: soft lockup - CPU#116 stuck for 94s! [swapper:0] It's simple enough to trigger this by doing a 10 minute sleep after a fresh bootup then starting a parallel kernel build. I suspect this might be reintroducing a problem we've had and fixed before, see the thread: http://marc.info/?l=linux-kernel&m=119546414004065&w=2 <---------------| touch the softlockup watchdog when exiting NOHZ state - we are obviously not locked up. Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
d0b27fa7 |
|
19-Apr-2008 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched: rt-group: synchonised bandwidth period Various SMP balancing algorithms require that the bandwidth period run in sync. Possible improvements are moving the rt_bandwidth thing into root_domain and keeping a span per rt_bandwidth which marks throttled cpus. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
903b8a8d |
|
28-Feb-2008 |
Karsten Wiese <fzu@wemgehoertderstaat.de> |
clockevents: optimise tick_nohz_stop_sched_tick() a bit Call ts = &per_cpu(tick_cpu_sched, cpu); and cpu = smp_processor_id(); once instead of twice. No functional change done, as changed code runs with local irq off. Reduces source lines and text size (20bytes on x86_64). [ akpm@linux-foundation.org: Build fix ] Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
a7901766 |
|
04-Mar-2008 |
Karsten Wiese <fzu@wemgehoertderstaat.de> |
time: don't touch an offlined CPU's ts->tick_stopped in tick_cancel_sched_timer() Silences WARN_ONs in rcu_enter_nohz() and rcu_exit_nohz(), which appeared before caused by (repeated) calls to: $ echo 0 > /sys/devices/system/cpu/cpu1/online $ echo 1 > /sys/devices/system/cpu/cpu1/online Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de> Cc: johnstul@us.ibm.com Cc: Rafael Wysocki <rjw@sisk.pl> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@elte.hu> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
2232c2d8 |
|
29-Feb-2008 |
Steven Rostedt <rostedt@goodmis.org> |
rcu: add support for dynamic ticks and preempt rcu The PREEMPT-RCU can get stuck if a CPU goes idle and NO_HZ is set. The idle CPU will not progress the RCU through its grace period and a synchronize_rcu my get stuck. Without this patch I have a box that will not boot when PREEMPT_RCU and NO_HZ are set. That same box boots fine with this patch. This patch comes from the -rt kernel where it has been tested for several months. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
cf4fc6cb |
|
08-Feb-2008 |
Li Zefan <lizf@cn.fujitsu.com> |
timekeeping: rename timekeeping_is_continuous to timekeeping_valid_for_hres Function timekeeping_is_continuous() no longer checks flag CLOCK_IS_CONTINUOUS, and it checks CLOCK_SOURCE_VALID_FOR_HRES now. So rename the function accordingly. Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
5df7fa1c |
|
01-Feb-2008 |
Thomas Gleixner <tglx@linutronix.de> |
tick-sched: add more debug information To allow better diagnosis of tick-sched related, especially NOHZ related problems, we need to know when the last wakeup via an irq happened and when the CPU left the idle state. Add two fields (idle_waketime, idle_exittime) to the tick_sched structure and add them to the timer_list output. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
6378ddb5 |
|
30-Jan-2008 |
Venki Pallipadi <venkatesh.pallipadi@intel.com> |
time: track accurate idle time with tick_sched.idle_sleeptime Current idle time in kstat is based on jiffies and is coarse grained. tick_sched.idle_sleeptime is making some attempt to keep track of idle time in a fine grained manner. But, it is not handling the time spent in interrupts fully. Make tick_sched.idle_sleeptime accurate with respect to time spent on handling interrupts and also add tick_sched.idle_lastupdate, which keeps track of last time when idle_sleeptime was updated. This statistics will be crucial for cpufreq-ondemand governor, which can shed some conservative gaurd band that is uses today while setting the frequency. The ondemand changes that uses the exact idle time is coming soon. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
b10db7f0 |
|
30-Jan-2008 |
Pavel Machek <pavel@ucw.cz> |
time: more timer related cleanups I was confused by FSEC = 10^15 NSEC statement, plus small whitespace fixes. When there's copyright, there should be GPL. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
4c9dc641 |
|
30-Jan-2008 |
Pavel Machek <pavel@ucw.cz> |
time: timer cleanups Small cleanups to tick-related code. Wrong preempt count is followed by BUG(), so it is hardly KERN_WARNING. Signed-off-by: Pavel Machek <pavel@suse.cz> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
2d44ae4d |
|
25-Jan-2008 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
hrtimer: clean up cpu->base locking tricks In order to more easily allow for the scheduler to use timers, clean up the locking a bit. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
48d5e258 |
|
25-Jan-2008 |
Peter Zijlstra <a.p.zijlstra@chello.nl> |
sched: rt throttling vs no_hz We need to teach no_hz about the rt throttling because its tick driven. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
d3938204 |
|
28-Nov-2007 |
Thomas Gleixner <tglx@linutronix.de> |
softlockup: fix false positives on CONFIG_NOHZ David Miller reported soft lockup false-positives that trigger on NOHZ due to CPUs idling for more than 10 seconds. The solution is touch the softlockup watchdog when we return from idle. (by definition we are not 'locked up' when we were idle) http://bugzilla.kernel.org/show_bug.cgi?id=9409 Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
#
8dce39c2 |
|
05-Nov-2007 |
Li Zefan <lizf@cn.fujitsu.com> |
time: fix inconsistent function names in comments Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
64e38eb0 |
|
24-Oct-2007 |
Adrian Bunk <bunk@kernel.org> |
clockevents: unexport tick_nohz_get_sleep_length This patch removes the unused EXPORT_SYMBOL_GPL(tick_nohz_get_sleep_length). Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
4d8b4e1e |
|
24-Oct-2007 |
Adrian Bunk <bunk@kernel.org> |
cpuidle: unexport tick_nohz_get_sleep_length This patch removes the unused EXPORT_SYMBOL_GPL(tick_nohz_get_sleep_length), which we no long user b/c we no longer build optional modules. Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Len Brown <len.brown@intel.com>
|
#
b2d9323d |
|
17-Oct-2007 |
John Stultz <johnstul@us.ibm.com> |
Use num_possible_cpus() instead of NR_CPUS for timer distribution To avoid lock contention, we distribute the sched_timer calls across the cpus so they do not trigger at the same instant. However, I used NR_CPUS, which can cause needless grouping on small smp systems depending on your kernel config. This patch converts to using num_possible_cpus() so we spread it as evenly as possible on every machine. Briefly tested w/ NR_CPUS=255 and verified reduced contention. Signed-off-by: John Stultz <johnstul@us.ibm.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
4f86d3a8 |
|
03-Oct-2007 |
Len Brown <len.brown@intel.com> |
cpuidle: consolidate 2.6.22 cpuidle branch into one patch commit e5a16b1f9eec0af7cfa0830304b41c1c0833cf9f Author: Len Brown <len.brown@intel.com> Date: Tue Oct 2 23:44:44 2007 -0400 cpuidle: shrink diff processor_idle.c | 440 +++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 429 insertions(+), 11 deletions(-) Signed-off-by: Len Brown <len.brown@intel.com> commit dfbb9d5aedfb18848a3e0d6f6e3e4969febb209c Author: Len Brown <len.brown@intel.com> Date: Wed Sep 26 02:17:55 2007 -0400 cpuidle: reduce diff size Reduces the cpuidle processor_idle.c diff vs 2.6.22 from this processor_idle.c | 2006 ++++++++++++++++++++++++++----------------- 1 file changed, 1219 insertions(+), 787 deletions(-) to this: processor_idle.c | 502 +++++++++++++++++++++++++++++++++++++++---- 1 file changed, 458 insertions(+), 44 deletions(-) ...for the purpose of making the cpuilde patch less invasive and easier to review. no functional changes. build tested only. Signed-off-by: Len Brown <len.brown@intel.com> commit 889172fc915f5a7fe20f35b133cbd205ce69bf6c Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Sep 13 13:40:05 2007 -0700 cpuidle: Retain old ACPI policy for !CONFIG_CPU_IDLE Retain the old policy in processor_idle, so that when CPU_IDLE is not configured, old C-state policy will still be used. This provides a clean gradual migration path from old ACPI policy to new cpuidle based policy. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 9544a8181edc7ecc33b3bfd69271571f98ed08bc Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Sep 13 13:39:17 2007 -0700 cpuidle: Configure governors by default Quoting Len "Do not give an option to users to shoot themselves in the foot". Remove the configurability of ladder and menu governors as they are needed for default policy of cpuidle. That way users will not be able to have cpuidle without any policy loosing all C-state power savings. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 8975059a2c1e56cfe83d1bcf031bcf4cb39be743 Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:27:07 2007 -0400 CPUIDLE: load ACPI properly when CPUIDLE is disabled Change the registration return codes for when CPUIDLE support is not compiled into the kernel. As a result, the ACPI processor driver will load properly even if CPUIDLE is unavailable. However, it may be possible to cleanup the ACPI processor driver further and eliminate some dead code paths. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit e0322e2b58dd1b12ec669bf84693efe0dc2414a8 Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:26:06 2007 -0400 CPUIDLE: remove cpuidle_get_bm_activity() Remove cpuidle_get_bm_activity() and updates governors accordingly. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 18a6e770d5c82ba26653e53d240caa617e09e9ab Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:25:58 2007 -0400 CPUIDLE: max_cstate fix Currently max_cstate is limited to 0, resulting in no idle processor power management on ACPI platforms. This patch restores the value to the array size. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 1fdc0887286179b40ce24bcdbde663172e205ef0 Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:25:40 2007 -0400 CPUIDLE: handle BM detection inside the ACPI Processor driver Update the ACPI processor driver to detect BM activity and limit state entry depth internally, rather than exposing such requirements to CPUIDLE. As a result, CPUIDLE can drop this ACPI-specific interface and become more platform independent. BM activity is now handled much more aggressively than it was in the original implementation, so some testing coverage may be needed to verify that this doesn't introduce any DMA buffer under-run issues. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 0ef38840db666f48e3cdd2b769da676c57228dd9 Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:25:14 2007 -0400 CPUIDLE: menu governor updates Tweak the menu governor to more effectively handle non-timer break events. Non-timer break events are detected by comparing the actual sleep time to the expected sleep time. In future revisions, it may be more reliable to use the timer data structures directly. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit bb4d74fca63fa96cf3ace644b15ae0f12b7df5a1 Author: Adam Belay <abelay@novell.com> Date: Tue Aug 21 18:24:40 2007 -0400 CPUIDLE: fix 'current_governor' sysfs entry Allow the "current_governor" sysfs entry to properly handle input terminated with '\n'. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit df3c71559bb69b125f1a48971bf0d17f78bbdf47 Author: Len Brown <len.brown@intel.com> Date: Sun Aug 12 02:00:45 2007 -0400 cpuidle: fix IA64 build (again) Signed-off-by: Len Brown <len.brown@intel.com> commit a02064579e3f9530fd31baae16b1fc46b5a7bca8 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Sun Aug 12 01:39:27 2007 -0400 cpuidle: Remove support for runtime changing of max_cstate Remove support for runtime changeability of max_cstate. Drivers can use use latency APIs. max_cstate can still be used as a boot time option and dmi override. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 0912a44b13adf22f5e3f607d263aed23b4910d7e Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Sun Aug 12 01:39:16 2007 -0400 cpuidle: Remove ACPI cstate_limit calls from ipw2100 ipw2100 already has code to use accetable_latency interfaces to limit the C-state. Remove the calls to acpi_set_cstate_limit and acpi_get_cstate_limit as they are redundant. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit c649a76e76be6bff1fd770d0a775798813a3f6e0 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Sun Aug 12 01:35:39 2007 -0400 cpuidle: compile fix for pause and resume functions Fix the compilation failure when cpuidle is not compiled in. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Adam Belay <adam.belay@novell.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 2305a5920fb8ee6ccec1c62ade05aa8351091d71 Author: Adam Belay <abelay@novell.com> Date: Thu Jul 19 00:49:00 2007 -0400 cpuidle: re-write Some portions have been rewritten to make the code cleaner and lighter weight. The following is a list of changes: 1.) the state name is now included in the sysfs interface 2.) detection, hotplug, and available state modifications are handled by CPUIDLE drivers directly 3.) the CPUIDLE idle handler is only ever installed when at least one cpuidle_device is enabled and ready 4.) the menu governor BM code no longer overflows 5.) the sysfs attributes are now printed as unsigned integers, avoiding negative values 6.) a variety of other small cleanups Also, Idle drivers are no longer swappable during runtime through the CPUIDLE sysfs inteface. On i386 and x86_64 most idle handlers (e.g. poll, mwait, halt, etc.) don't benefit from an infrastructure that supports multiple states, so I think using a more general case idle handler selection mechanism would be cleaner. Signed-off-by: Adam Belay <abelay@novell.com> Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit df25b6b56955714e6e24b574d88d1fd11f0c3ee5 Author: Len Brown <len.brown@intel.com> Date: Tue Jul 24 17:08:21 2007 -0400 cpuidle: fix IA64 buid Signed-off-by: Len Brown <len.brown@intel.com> commit fd6ada4c14488755ff7068860078c437431fbccd Author: Adrian Bunk <bunk@stusta.de> Date: Mon Jul 9 11:33:13 2007 -0700 cpuidle: static make cpuidle_replace_governor() static Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit c1d4a2cebcadf2429c0c72e1d29aa2a9684c32e0 Author: Adrian Bunk <bunk@stusta.de> Date: Tue Jul 3 00:54:40 2007 -0400 cpuidle: static This patch makes the needlessly global struct menu_governor static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit dbf8780c6e8d572c2c273da97ed1cca7608fd999 Author: Andrew Morton <akpm@linux-foundation.org> Date: Tue Jul 3 00:49:14 2007 -0400 export symbol tick_nohz_get_sleep_length ERROR: "tick_nohz_get_sleep_length" [drivers/cpuidle/governors/menu.ko] undefined! ERROR: "tick_nohz_get_idle_jiffies" [drivers/cpuidle/governors/menu.ko] undefined! And please be sure to get your changes to core kernel suitably reviewed. Cc: Adam Belay <abelay@novell.com> Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 29f0e248e7017be15f99febf9143a2cef00b2961 Author: Andrew Morton <akpm@linux-foundation.org> Date: Tue Jul 3 00:43:04 2007 -0400 tick.h needs hrtimer.h It uses hrtimers. Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit e40cede7d63a029e92712a3fe02faee60cc38fb4 Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:40:34 2007 -0400 cpuidle: first round of documentation updates Documentation changes based on Pavel's feedback. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 83b42be2efece386976507555c29e7773a0dfcd1 Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:39:25 2007 -0400 cpuidle: add rating to the governors and pick the one with highest rating by default Introduce a governor rating scheme to pick the right governor by default. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit d2a74b8c5e8f22def4709330d4bfc4a29209b71c Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:38:08 2007 -0400 cpuidle: make cpuidle sysfs driver governor switch off by default Make default cpuidle sysfs to show current_governor and current_driver in read-only mode. More elaborate available_governors and available_drivers with writeable current_governor and current_driver interface only appear with "cpuidle_sysfs_switch" boot parameter. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 1f60a0e80bf83cf6b55c8845bbe5596ed8f6307b Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:37:00 2007 -0400 cpuidle: menu governor: change the early break condition Change the C-state early break out algorithm in menu governor. We only look at early breakouts that result in wakeups shorter than idle state's target_residency. If such a breakout is frequent enough, eliminate the particular idle state upto a timeout period. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 45a42095cf64b003b4a69be3ce7f434f97d7af51 Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:35:38 2007 -0400 cpuidle: fix uninitialized variable in sysfs routine Fix the uninitialized usage of ret. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 80dca7cdba3e6ee13eae277660873ab9584eb3be Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:34:16 2007 -0400 cpuidle: reenable /proc/acpi//power interface for the time being Keep /proc/acpi/processor/CPU*/power around for a while as powertop depends on it. It will be marked deprecated and removed in future. powertop can use cpuidle interfaces instead. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 589c37c2646c5e3813a51255a5ee1159cb4c33fc Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Jul 3 00:32:37 2007 -0400 cpuidle: menu governor and hrtimer compile fix Compile fix for menu governor. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 0ba80bd9ab3ed304cb4f19b722e4cc6740588b5e Author: Len Brown <len.brown@intel.com> Date: Thu May 31 22:51:43 2007 -0400 cpuidle: build fix - cpuidle vs ipw2100 module ERROR: "acpi_set_cstate_limit" [drivers/net/wireless/ipw2100.ko] undefined! Signed-off-by: Len Brown <len.brown@intel.com> commit d7d8fa7f96a7f7682be7c6cc0cc53fa7a18c3b58 Author: Adam Belay <abelay@novell.com> Date: Sat Mar 24 03:47:07 2007 -0400 cpuidle: add the 'menu' governor Here is my first take at implementing an idle PM governor that takes full advantage of NO_HZ. I call it the 'menu' governor because it considers the full list of idle states before each entry. I've kept the implementation fairly simple. It attempts to guess the next residency time and then chooses a state that would meet at least the break-even point between power savings and entry cost. To this end, it selects the deepest idle state that satisfies the following constraints: 1. If the idle time elapsed since bus master activity was detected is below a threshold (currently 20 ms), then limit the selection to C2-type or above. 2. Do not choose a state with a break-even residency that exceeds the expected time remaining until the next timer interrupt. 3. Do not choose a state with a break-even residency that exceeds the elapsed time between the last pair of break events, excluding timer interrupts. This governor has an advantage over "ladder" governor because it proactively checks how much time remains until the next timer interrupt using the tick infrastructure. Also, it handles device interrupt activity more intelligently by not including timer interrupts in break event calculations. Finally, it doesn't make policy decisions using the number of state entries, which can have variable residency times (NO_HZ makes these potentially very large), and instead only considers sleep time deltas. The menu governor can be selected during runtime using the cpuidle sysfs interface like so: "echo "menu" > /sys/devices/system/cpu/cpuidle/current_governor" Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Len Brown <len.brown@intel.com> commit a4bec7e65aa3b7488b879d971651cc99a6c410fe Author: Adam Belay <abelay@novell.com> Date: Sat Mar 24 03:47:03 2007 -0400 cpuidle: export time until next timer interrupt using NO_HZ Expose information about the time remaining until the next timer interrupt expires by utilizing the dynticks infrastructure. Also modify the main idle loop to allow dynticks to handle non-interrupt break events (e.g. DMA). Finally, expose sleep ticks information to external code. Thomas Gleixner is responsible for much of the code in this patch. However, I've made some additional changes, so I'm probably responsible if there are any bugs or oversights :) Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 2929d8996fbc77f41a5ff86bb67cdde3ca7d2d72 Author: Adam Belay <abelay@novell.com> Date: Sat Mar 24 03:46:58 2007 -0400 cpuidle: governor API changes This patch prepares cpuidle for the menu governor. It adds an optional stage after idle state entry to give the governor an opportunity to check why the state was exited. Also it makes sure the idle loop returns after each state entry, allowing the appropriate dynticks code to run. Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 3a7fd42f9825c3b03e364ca59baa751bb350775f Author: Venki Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Apr 26 00:03:59 2007 -0700 cpuidle: hang fix Prevent hang on x86-64, when ACPI processor driver is added as a module on a system that does not support C-states. x86-64 expects all idle handlers to enable interrupts before returning from idle handler. This is due to enter_idle(), exit_idle() races. Make cpuidle_idle_call() confirm to this when there is no pm_idle_old. Also, cpuidle look at the return values of attch_driver() and set current_driver to NULL if attach fails on all CPUs. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 4893339a142afbd5b7c01ffadfd53d14746e858e Author: Shaohua Li <shaohua.li@intel.com> Date: Thu Apr 26 10:40:09 2007 +0800 cpuidle: add support for max_cstate limit With CPUIDLE framework, the max_cstate (to limit max cpu c-state) parameter is ingored. Some systems require it to ignore C2/C3 and some drivers like ipw require it too. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 43bbbbe1cb998cbd2df656f55bb3bfe30f30e7d1 Author: Shaohua Li <shaohua.li@intel.com> Date: Thu Apr 26 10:40:13 2007 +0800 cpuidle: add cpuidle_fore_redetect_devices API add cpuidle_force_redetect_devices API, which forces all CPU redetect idle states. Next patch will use it. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit d1edadd608f24836def5ec483d2edccfb37b1d19 Author: Shaohua Li <shaohua.li@intel.com> Date: Thu Apr 26 10:40:01 2007 +0800 cpuidle: fix sysfs related issue Fix the cpuidle sysfs issue. a. make kobject dynamicaly allocated b. fixed sysfs init issue to avoid suspend/resume issue Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 7169a5cc0d67b263978859672e86c13c23a5570d Author: Randy Dunlap <randy.dunlap@oracle.com> Date: Wed Mar 28 22:52:53 2007 -0400 cpuidle: 1-bit field must be unsigned A 1-bit bitfield has no room for a sign bit. drivers/cpuidle/governors/ladder.c:54:16: error: dubious bitfield without explicit `signed' or `unsigned' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 4658620158dc2fbd9e4bcb213c5b6fb5d05ba7d4 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Wed Mar 28 22:52:41 2007 -0400 cpuidle: fix boot hang Patch for cpuidle boot hang reported by Larry Finger here. http://www.ussg.iu.edu/hypermail/linux/kernel/0703.2/2025.html Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit c17e168aa6e5fe3851baaae8df2fbc1cf11443a9 Author: Len Brown <len.brown@intel.com> Date: Wed Mar 7 04:37:53 2007 -0500 cpuidle: ladder does not depend on ACPI build fix for CONFIG_ACPI=n In file included from drivers/cpuidle/governors/ladder.c:21: include/acpi/processor.h:88: error: expected specifier-qualifier-list before âacpi_integerâ include/acpi/processor.h:106: error: expected specifier-qualifier-list before âacpi_integerâ include/acpi/processor.h:168: error: expected specifier-qualifier-list before âacpi_handleâ Signed-off-by: Len Brown <len.brown@intel.com> commit 8c91d958246bde68db0c3f0c57b535962ce861cb Author: Adrian Bunk <bunk@stusta.de> Date: Tue Mar 6 02:29:40 2007 -0800 cpuidle: make code static This patch makes the following needlessly global code static: - driver.c: __cpuidle_find_driver() - governor.c: __cpuidle_find_governor() - ladder.c: struct ladder_governor Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Adam Belay <abelay@novell.com> Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 0c39dc3187094c72c33ab65a64d2017b21f372d2 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Wed Mar 7 02:38:22 2007 -0500 cpu_idle: fix build break This patch fixes a build breakage with !CONFIG_HOTPLUG_CPU and CONFIG_CPU_IDLE. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 8112e3b115659b07df340ef170515799c0105f82 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Tue Mar 6 02:29:39 2007 -0800 cpuidle: build fix for !CPU_IDLE Fix the compile issues when CPU_IDLE is not configured. Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Adam Belay <abelay@novell.com> Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> commit 1eb4431e9599cd25e0d9872f3c2c8986821839dd Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Feb 22 13:54:57 2007 -0800 cpuidle take2: Basic documentation for cpuidle Documentation for cpuidle infrastructure Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> commit ef5f15a8b79123a047285ec2e3899108661df779 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Feb 22 13:54:03 2007 -0800 cpuidle take2: Hookup ACPI C-states driver with cpuidle Hookup ACPI C-states onto generic cpuidle infrastructure. drivers/acpi/procesor_idle.c is now a ACPI C-states driver that registers as a driver in cpuidle infrastructure and the policy part is removed from drivers/acpi/processor_idle.c. We use governor in cpuidle instead. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Len Brown <len.brown@intel.com> commit 987196fa82d4db52c407e8c9d5dec884ba602183 Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Date: Thu Feb 22 13:52:57 2007 -0800 cpuidle take2: Core cpuidle infrastructure Announcing 'cpuidle', a new CPU power management infrastructure to manage idle CPUs in a clean and efficient manner. cpuidle separates out the drivers that can provide support for multiple types of idle states and policy governors that decide on what idle state to use at run time. A cpuidle driver can support multiple idle states based on parameters like varying power consumption, wakeup latency, etc (ACPI C-states for example). A cpuidle governor can be usage model specific (laptop, server, laptop on battery etc). Main advantage of the infrastructure being, it allows independent development of drivers and governors and allows for better CPU power management. A huge thanks to Adam Belay and Shaohua Li who were part of this mini-project since its beginning and are greatly responsible for this patchset. This patch: Core cpuidle infrastructure. Introduces a new abstraction layer for cpuidle: * which manages drivers that can support multiple idles states. Drivers can be generic or particular to specific hardware/platform * allows pluging in multiple policy governors that can take idle state policy decision * The core also has a set of sysfs interfaces with which administrato can know about supported drivers and governors and switch them at run time. Signed-off-by: Adam Belay <abelay@novell.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
|
#
5e41d0d6 |
|
16-Sep-2007 |
Thomas Gleixner <tglx@linutronix.de> |
clockevents: prevent stale tick update on offline cpu Taking a cpu offline removes the cpu from the online mask before the CPU_DEAD notification is done. The clock events layer does the cleanup of the dead CPU from the CPU_DEAD notifier chain. tick_do_timer_cpu is used to avoid xtime lock contention by assigning the task of jiffies xtime updates to one CPU. If a CPU is taken offline, then this assignment becomes stale. This went unnoticed because most of the time the offline CPU went dead before the online CPU reached __cpu_die(), where the CPU_DEAD state is checked. In the case that the offline CPU did not reach the DEAD state before we reach __cpu_die(), the code in there goes to sleep for 100ms. Due to the stale time update assignment, the system is stuck forever. Take the assignment away when a cpu is not longer in the cpu_online_mask. We do this in the last call to tick_nohz_stop_sched_tick() when the offline CPU is on the way to the final play_dead() idle entry. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
#
3704540b |
|
21-Jul-2007 |
John Stultz <johnstul@us.ibm.com> |
tick management: spread timer interrupt After discussing w/ Thomas over IRC, it seems the issue is the sched tick fires on every cpu at the same time, causing extra lock contention. This smaller change, adds an extra offset per cpu so the ticks don't line up. This patch also drops the idle latency from 40us down to under 20us. Signed-off-by: john stultz <johnstul@us.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
eaad084b |
|
29-May-2007 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: prevent multiplication overflow - stop timer for huge timeouts get_next_timer_interrupt() returns a delta of (LONG_MAX > 1) in case there is no timer pending. On 64 bit machines this results in a multiplication overflow in tick_nohz_stop_sched_tick(). Reported by: Dave Miller <davem@davemloft.net> Make the return value a constant and limit the return value to a 32 bit value. When the max timeout value is returned, we can safely stop the tick timer device. The max jiffies delta results in a 12 days timeout for HZ=1000. In the long term the get_next_timer_interrupt() code needs to be reworked to return ktime instead of jiffies, but we have to wait until the last users of the original NO_IDLE_HZ code are converted. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
35282316 |
|
23-May-2007 |
Thomas Gleixner <tglx@linutronix.de> |
NOHZ: Rate limit the local softirq pending warning output The warning in the NOHZ code, which triggers when a CPU goes idle with softirqs pending can fill up the logs quite quickly. Rate limit the output until we found the root cause of that problem. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
46cb4b7c |
|
08-May-2007 |
Siddha, Suresh B <suresh.b.siddha@intel.com> |
sched: dynticks idle load balancing Fix the process idle load balancing in the presence of dynticks. cpus for which ticks are stopped will sleep till the next event wakes it up. Potentially these sleeps can be for large durations and during which today, there is no periodic idle load balancing being done. This patch nominates an owner among the idle cpus, which does the idle load balancing on behalf of the other idle cpus. And once all the cpus are completely idle, then we can stop this idle load balancing too. Checks added in fast path are minimized. Whenever there are busy cpus in the system, there will be an owner(idle cpu) doing the system wide idle load balancing. Open items: 1. Intelligent owner selection (like an idle core in a busy package). 2. Merge with rcu's nohz_cpu_mask? Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
d3ed7824 |
|
08-May-2007 |
Thomas Gleixner <tglx@linutronix.de> |
highres/dyntick: prevent xtime lock contention While the !highres/!dyntick code assigns the duty of the do_timer() call to one specific CPU, this was dropped in the highres/dyntick part during development. Steven Rostedt discovered the xtime lock contention on highres/dyntick due to several CPUs trying to update jiffies. Add the single CPU assignement back. In the dyntick case this needs to be handled carefully, as the CPU which has the do_timer() duty must drop the assignement and let it be grabbed by another CPU, which is active. Otherwise the do_timer() calls would not happen during the long sleep. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Acked-by: Mark Lord <mlord@pobox.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
9e203bcc |
|
24-Feb-2007 |
David S. Miller <davem@sunset.davemloft.net> |
[TIME] tick-sched: Add missing asm/irq_regs.h include. Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
|
#
bc5393a6 |
|
19-Feb-2007 |
Thomas Gleixner <tglx@linutronix.de> |
[PATCH] NOHZ: Produce debug output instead of a BUG() The BUG_ON() in tick_nohz_stop_sched_tick() triggers on some boxen. Remove the BUG_ON and print information about the pending softirq to allow better debugging of the problem. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
6ba9b346 |
|
19-Feb-2007 |
Ingo Molnar <mingo@elte.hu> |
[PATCH] NOHZ: Fix RCU handling When a CPU is needed for RCU the tick has to continue even when it was stopped before. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
289f480a |
|
16-Feb-2007 |
Ingo Molnar <mingo@elte.hu> |
[PATCH] Add debugging feature /proc/timer_list add /proc/timer_list, which prints all currently pending (high-res) timers, all clock-event sources and their parameters in a human-readable form. Sample output: Timer List Version: v0.1 HRTIMER_MAX_CLOCK_BASES: 2 now at 4246046273872 nsecs cpu: 0 clock 0: .index: 0 .resolution: 1 nsecs .get_time: ktime_get_real .offset: 1273998312645738432 nsecs active timers: clock 1: .index: 1 .resolution: 1 nsecs .get_time: ktime_get .offset: 0 nsecs active timers: #0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_stop_sched_tick, swapper/0 # expires at 4246432689566 nsecs [in 386415694 nsecs] #1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, pcscd/2050 # expires at 4247018194689 nsecs [in 971920817 nsecs] #2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, irqbalance/1909 # expires at 4247351358392 nsecs [in 1305084520 nsecs] #3: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, crond/2157 # expires at 4249097614968 nsecs [in 3051341096 nsecs] #4: <f5a90ec8>, it_real_fn, do_setitimer, syslogd/1888 # expires at 4251329900926 nsecs [in 5283627054 nsecs] .expires_next : 4246432689566 nsecs .hres_active : 1 .check_clocks : 0 .nr_events : 31306 .idle_tick : 4246020791890 nsecs .tick_stopped : 1 .idle_jiffies : 986504 .idle_calls : 40700 .idle_sleeps : 36014 .idle_entrytime : 4246019418883 nsecs .idle_sleeptime : 4178181972709 nsecs cpu: 1 clock 0: .index: 0 .resolution: 1 nsecs .get_time: ktime_get_real .offset: 1273998312645738432 nsecs active timers: clock 1: .index: 1 .resolution: 1 nsecs .get_time: ktime_get .offset: 0 nsecs active timers: #0: <f5a90ec8>, hrtimer_sched_tick, hrtimer_restart_sched_tick, swapper/0 # expires at 4246050084568 nsecs [in 3810696 nsecs] #1: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, atd/2227 # expires at 4261010635003 nsecs [in 14964361131 nsecs] #2: <f5a90ec8>, hrtimer_wakeup, do_nanosleep, smartd/2332 # expires at 5469485798970 nsecs [in 1223439525098 nsecs] .expires_next : 4246050084568 nsecs .hres_active : 1 .check_clocks : 0 .nr_events : 24043 .idle_tick : 4246046084568 nsecs .tick_stopped : 0 .idle_jiffies : 986510 .idle_calls : 26360 .idle_sleeps : 22551 .idle_entrytime : 4246043874339 nsecs .idle_sleeptime : 4170763761184 nsecs tick_broadcast_mask: 00000003 event_broadcast_mask: 00000001 CPU#0's local event device: Clock Event Device: lapic capabilities: 0000000e max_delta_ns: 807385544 min_delta_ns: 1443 mult: 44624025 shift: 32 set_next_event: lapic_next_event set_mode: lapic_timer_setup event_handler: hrtimer_interrupt .installed: 1 .expires: 4246432689566 nsecs CPU#1's local event device: Clock Event Device: lapic capabilities: 0000000e max_delta_ns: 807385544 min_delta_ns: 1443 mult: 44624025 shift: 32 set_next_event: lapic_next_event set_mode: lapic_timer_setup event_handler: hrtimer_interrupt .installed: 1 .expires: 4246050084568 nsecs Clock Event Device: hpet capabilities: 00000007 max_delta_ns: 2147483647 min_delta_ns: 3352 mult: 61496110 shift: 32 set_next_event: hpet_next_event set_mode: hpet_set_mode event_handler: handle_nextevt_broadcast Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
#
79bf2bb3 |
|
16-Feb-2007 |
Thomas Gleixner <tglx@linutronix.de> |
[PATCH] tick-management: dyntick / highres functionality With Ingo Molnar <mingo@elte.hu> Add functions to provide dynamic ticks and high resolution timers. The code which keeps track of jiffies and handles the long idle periods is shared between tick based and high resolution timer based dynticks. The dyntick functionality can be disabled on the kernel commandline. Provide also the infrastructure to support high resolution timers. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: john stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|