can: canxl: update CAN infrastructure for CAN XL frames

- add new ETH_P_CANXL ethernet protocol type
- update skb checks for CAN XL
- add alloc_canxl_skb() which now needs a data length parameter
- introduce init_can_skb_reserve() to reduce code duplication

Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

net: dsa: add Renesas RZ/N1 switch tag driver

The switch that is present on the Renesas RZ/N1 SoC uses a specific
VLAN value followed by 6 bytes which contains forwarding configuration.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

if_ether.h: add EtherCAT Ethertype

Add the Ethertype for EtherCAT protocol.

Signed-off-by: Daniel Braunwarth <daniel@braunwarth.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

if_ether.h: add PROFINET Ethertype

Add the Ethertype for PROFINET protocol.

Signed-off-by: Daniel Braunwarth <daniel@braunwarth.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix Comment of ETH_P_802_3_MIN

The description of ETH_P_802_3_MIN is misleading.
The value of EthernetType in Ethernet II frame is more than 0x0600,
the value of Length in 802.3 frame is less than 0x0600.

Signed-off-by: Xiayu Zhang <Xiayu.Zhang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether: add EtherType for proprietary Realtek protocols

Add a new EtherType ETH_P_REALTEK to the if_ether.h uapi header. The
EtherType 0x8899 is used in a number of different protocols from Realtek
Semiconductor Corp [1], so no general assumptions should be made when
trying to decode such packets. Observed protocols include:

0x1 - Realtek Remote Control protocol [2]
0x2 - Echo protocol [2]
0x3 - Loop detection protocol [2]
0x4 - RTL8365MB 4- and 8-byte switch CPU tag protocols [3]
0x9 - RTL8306 switch CPU tag protocol [4]
0xA - RTL8366RB switch CPU tag protocol [4]

[1] https://lore.kernel.org/netdev/CACRpkdYQthFgjwVzHyK3DeYUOdcYyWmdjDPG=Rf9B3VrJ12Rzg@mail.gmail.com/
[2] https://www.wireshark.org/lists/ethereal-dev/200409/msg00090.html
[3] https://lore.kernel.org/netdev/20210822193145.1312668-4-alvin@pqrs.dk/
[4] https://lore.kernel.org/netdev/20200708122537.1341307-2-linus.walleij@linaro.org/

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mctp: Add device handling and netlink interface

This change adds the infrastructure for managing MCTP netdevices; we add
a pointer to the AF_MCTP-specific data to struct netdevice, and hook up
the rtnetlink operations for adding and removing addresses.

Includes changes from Matt Johnston <matt@codeconstruct.com.au>.

Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: uapi: cfm: Added EtherType used by the CFM protocol.

This EtherType is used by all CFM protocal frames transmitted
according to 802.1Q section 12.14.

Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bridge: uapi: mrp: Add mrp attributes.

Add new nested netlink attribute to configure the MRP. These attributes are used
by the userspace to add/delete/configure MRP instances and by the kernel to
notify the userspace when the MRP ring gets open/closed. MRP nested attribute
has the following attributes:

IFLA_BRIDGE_MRP_INSTANCE - the parameter type is br_mrp_instance which contains
the instance id, and the ifindex of the two ports. The ports can't be part of
multiple instances. This is used to create/delete MRP instances.

IFLA_BRIDGE_MRP_PORT_STATE - the parameter type is u32. Which can be forwarding,
blocking or disabled.

IFLA_BRIDGE_MRP_PORT_ROLE - the parameter type is br_mrp_port_role which
contains the instance id and the role. The role can be primary or secondary.

IFLA_BRIDGE_MRP_RING_STATE - the parameter type is br_mrp_ring_state which
contains the instance id and the state. The state can be open or closed.

IFLA_BRIDGE_MRP_RING_ROLE - the parameter type is br_mrp_ring_role which
contains the instance id and the ring role. The role can be MRM or MRC.

IFLA_BRIDGE_MRP_START_TEST - the parameter type is br_mrp_start_test which
contains the instance id, the interval at which to send the MRP_Test frames,
how many test frames can be missed before declaring the ring open and the
period which represent for how long to send the test frames.

Also add the file include/uapi/linux/mrp_bridge.h which defines all the types
used by MRP that are also needed by the userpace.

Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add a define for LLDP ethertype

Add a new define ETH_P_LLDP for Link Layer Discovery Protocol (LLDP)
ethertype.

Suggested-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ether: Add dedicated Ethertype for pseudo-802.1Q DSA tagging

There are two possible utilizations so far:

- Switch devices that don't support a native insertion/extraction header
on the CPU port may still enjoy the benefits of port isolation with a
custom VLAN tag.

For this, they need to have a customizable TPID in hardware and a new
Ethertype to distinguish between real 802.1Q traffic and the private
tags used for port separation.

- Switches that don't support the deactivation of VLAN awareness, but
still want to have a mode in which they accept all traffic, including
frames that are tagged with a VLAN not configured on their ports, may
use this as a fake to trick the hardware into thinking that the TPID
for VLAN is something other than 0x8100.

What follows after the ETH_P_DSA_8021Q EtherType is a regular VLAN
header (TCI), however there is no other EtherType that can be used for
this purpose and doesn't already have a well-defined meaning.
ETH_P_8021AD, ETH_P_QINQ1, ETH_P_QINQ2 and ETH_P_QINQ3 expect that
another follow-up VLAN tag is present, which is not the case here.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off

When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().

The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.

The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.

In rx path single tag case, it works as follows:

- Before skb_reorder_vlan_header()

mac_header data
v v
+-------------------+-------------+------+----
| ETH | VLAN | ETH |
| ADDRS | TPID | TCI | TYPE |
+-------------------+-------------+------+----
<-------- mac_len --------->
<------------->
to be removed

- After skb_reorder_vlan_header()

mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<-------- mac_len --------->

This is ok, but in rx double tag case, it corrupts packets:

- Before skb_reorder_vlan_header()

mac_header data
v v
+-------------------+-------------+-------------+------+----
| ETH | VLAN | VLAN | ETH |
| ADDRS | TPID | TCI | TPID | TCI | TYPE |
+-------------------+-------------+-------------+------+----
<--------------- mac_len ---------------->
<------------->
should be removed
<--------------------------->
actually will be removed

- After skb_reorder_vlan_header()

mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<--------------- mac_len ---------------->

So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.

skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.

Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff11170 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

uapi: Add 802.11 Preauthentication to if_ether

This adds 0x88c7 protocol type to if_ether.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

uapi/if_ether.h: move __UAPI_DEF_ETHHDR libc define

This fixes a compile problem of some user space applications by not
including linux/libc-compat.h in uapi/if_ether.h.

linux/libc-compat.h checks which "features" the header files, included
from the libc, provide to make the Linux kernel uapi header files only
provide no conflicting structures and enums. If a user application mixes
kernel headers and libc headers it could happen that linux/libc-compat.h
gets included too early where not all other libc headers are included
yet. Then the linux/libc-compat.h would not prevent all the
redefinitions and we run into compile problems.
This patch removes the include of linux/libc-compat.h from
uapi/if_ether.h to fix the recently introduced case, but not all as this
is more or less impossible.

It is no problem to do the check directly in the if_ether.h file and not
in libc-compat.h as this does not need any fancy glibc header detection
as glibc never provided struct ethhdr and should define
__UAPI_DEF_ETHHDR by them self when they will provide this.

The following test program did not compile correctly any more:

#include <linux/if_ether.h>
#include <netinet/in.h>
#include <linux/in.h>

int main(void)
{
return 0;
}

Fixes: 6926e041a892 ("uapi/if_ether.h: prevent redefinition of struct ethhdr")
Reported-by: Guillaume Nault <g.nault@alphalink.fr>
Cc: <stable@vger.kernel.org> # 4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

uapi/if_ether.h: prevent redefinition of struct ethhdr

Musl provides its own ethhdr struct definition. Add a guard to prevent
its definition of the appropriate musl header has already been included.

glibc does not implement this header, but when glibc will implement this
they can just define __UAPI_DEF_ETHHDR 0 to make it work with the
kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: erspan: introduce erspan v2 for ip_gre

The patch adds support for erspan version 2. Not all features are
supported in this patch. The SGT (security group tag), GRA (timestamp
granularity), FT (frame type) are set to fixed value. Only hardware
ID and direction are configurable. Optional subheader is also not
supported.

Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

License cleanup: add SPDX license identifier to uapi header files with a license

Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.

Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.

GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:

NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".

This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.

Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)

SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ether: Add support for multiplexing and aggregation type

Define the Qualcomm multiplexing and aggregation (MAP) ether type 0x00F9.
This is needed for receiving data in the MAP protocol like RMNET. This is
not an officially registered ID.

Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether: add NSH ethertype

The NSH draft says:

An IEEE EtherType, 0x894F, has been allocated for NSH.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

if_ether: add forces ife lfb type

This patch adds the forces IFE lfb type according to IEEE registered
ethertypes. See http://standards-oui.ieee.org/ethertype/eth.txt for more
information. Since there exists the IFE subsystem it can be used there.

This patch also use the correct word "ForCES" instead of "FoRCES" which
is a spelling error inside the IEEE ethertype specification.

Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gre: introduce native tunnel support for ERSPAN

The patch adds ERSPAN type II tunnel support. The implementation
is based on the draft at [1]. One of the purposes is for Linux
box to be able to receive ERSPAN monitoring traffic sent from
the Cisco switch, by creating a ERSPAN tunnel device.
In addition, the patch also adds ERSPAN TX, so Linux virtual
switch can redirect monitored traffic to the ERSPAN tunnel device.
The traffic will be encapsulated into ERSPAN and sent out.

The implementation reuses tunnel key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100

To use the above device as ERSPAN receiver, configure
Nexus 5000 switch as below:

monitor session 100 type erspan-source
erspan-id 123
vrf default
destination ip 172.16.1.200
source interface Ethernet1/11 both
source interface Ethernet1/12 both
no shut
monitor erspan origin ip-address 172.16.1.100 global

[1] https://tools.ietf.org/html/draft-foschiano-erspan-01
[2] iproute2 patch: http://marc.info/?l=linux-netdev&m=150306086924951&w=2
[3] test script: http://marc.info/?l=linux-netdev&m=150231021807304&w=2

Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDMA: Adding ethertype ETH_P_IBOE

Update the if_ether.h with the ethertype for Infiniband over
Ethernet packets. Also, removing the occurances of 0x8915
from infiniband vendor drivers.

Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

ethernet: use net core MTU range checking in more drivers

Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.

acenic:
- min_mtu = 0, max_mtu = 9000

amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu

amd/xgbe:
- min_mtu = 0, max_mtu = 9000

sb1250:
- min_mtu = 0, max_mtu = 1518

cxgb3:
- min_mtu = 81, max_mtu = 65535

cxgb4:
- min_mtu = 81, max_mtu = 9600

cxgb4vf:
- min_mtu = 81, max_mtu = 65535

benet:
- min_mtu = 256, max_mtu = 9000

ibmveth:
- min_mtu = 68, max_mtu = 65535

ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu

jme:
- min_mtu = 1280, max_mtu = 9202

mv643xx_eth:
- min_mtu = 64, max_mtu = 9500

mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions

ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500

netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)

qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000

qualcomm/emac:
- min_mtu = 46, max_mtu = 9194

xilinx_axienet:
- min_mtu = 64, max_mtu = 9000

Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: deprecate eth_change_mtu, remove usage

With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.

Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.

v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86

CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ncsi: NCSI command packet handler

The NCSI command packets are sent from MC (Management Controller)
to remote end. They are used for multiple purposes: probe existing
NCSI package/channel, retrieve NCSI channel's capability, configure
NCSI channel etc.

This defines struct to represent NCSI command packets and introduces
function ncsi_xmit_cmd(), which will be used to transmit NCSI command
packet according to the request. The request is represented by struct
ncsi_cmd_arg.

Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/hsr: Added support for HSR v1

This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.

Main changes are in the supervision frame handling and its
ethertype field.

Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

uapi: add MACsec bits

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether: add IEEE 1722 ethertype - TSN

IEEE 1722 describes AVB (later renamed to TSN - Time Sensitive
Networking), a protocol, encapsualtion and synchronization to utilize
standard networks for audio/video (and later other time-sensitive)
streams.

This standard uses ethertype 0x22F0.

http://standards.ieee.org/develop/regauth/ethertype/eth.txt

This is a respin of a previous patch ("ether: add AVB frame type
ETH_P_AVB")

CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-api@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Henrik Austad <henrik@austad.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: reduce number of protocol hooks

DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.

This patch proceeds with adding a new layer of abstraction and two new
functions:

dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c

dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c

When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.

A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.

This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ether: add loopback type ETH_P_LOOPBACK

Per IEEE 802.3*, the correct packet type for loopback 0x9000. There's
already one ETH_P_LOOP 0x0060, which has been there for ages, however it's
plainly wrong as anything that small is considered a length field.

We can't remove it because legacy, so add a new type which corresponds to
the correct id.

http://www.iana.org/assignments/ieee-802-numbers/ieee-802-numbers.xhtml

CC: "David S. Miller" <davem@davemloft.net>
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Neil Jerram <Neil.Jerram@metaswitch.com>
CC: Simon Horman <horms@verge.net.au>
CC: Arvid Brodin <Arvid.Brodin@xdin.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

if_ether.h: add IEEE 802.21 Ethertype

Add the Ethertype for IEEE Std 802.21 - Media Independent Handover
Protocol. This Ethertype is used for network control messages.

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: order MPLS ethertypes numerically

All ethertypes other than ETH_P_MPLS_UC, ETH_P_MPLS_MC and
ETH_P_ATMMPOA were already ordered numerically. This commit moves
those three ETH_P_... values into correct numerical order too.

Signed-off-by: Neil Jerram <Neil.Jerram@metaswitch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)

High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).

Signed-off-by: Arvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: add ETH_P_802_3_MIN

Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.

Also update all the users of this value that David Miller and
I could find to use the new constant.

Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.

As suggested by Jesse Gross.

Compile tested only.

Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/8021q: Implement Multiple VLAN Registration Protocol (MVRP)

Initial implementation of the Multiple VLAN Registration Protocol
(MVRP) from IEEE 802.1Q-2011, based on the existing implementation
of the GARP VLAN Registration Protocol (GVRP).

Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

if_ether.h: add B.A.T.M.A.N.-Advanced Ethertype

Add Ethertype 0x4305 (not an officially registered id).
This Ethertype is used by every frame generated by B.A.T.M.A.N.-Advanced. Its
definition is currently batman-adv local only and since it is not officially
registered it is better to make its definition kernel-wide so that we avoid
collisions given by future unofficial uses of the same Ethertype.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

UAPI: (Scripted) Disintegrate include/linux

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>