PCI: switchtec: Add support for PCIe Gen5 devices

Advertise support of Gen5 devices in the driver's device ID table and
add the same IDs for the switchtec quirks. Also update driver code to
accommodate them.

Link: https://lore.kernel.org/r/20230624000003.2315364-3-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

ntb_hw_switchtec: Remove code for disabling ID protection

ID protection is a firmware setting for NT window access control. With
it enabled, only the posted requests with requester IDs in the requester
ID table will be allowed to access the NT windows. Otherwise all posted
requests are allowed. Normally user will configure it statically via the
Switchtec config file, and it will take effect when the firmware boots
up. The driver can also toggle the ID protection setting dynamically,
which will overwrite the static setting in the Switchtec config file as
a side effect.

Currently, the driver disables the ID protection. However, it's not
necessary to disable the ID protection at the driver level as the driver
has already configured the proper requester IDs in the requester ID
table to allow the corresponding posted requests to hit the NT windows.
Remove the code that disables the ID protection to make the static
setting prevail.

Note: ID protection is not applicable to non-posted requests.

Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

PCI/switchtec: Add check of event support

Not all events are supported by every gen/variant of the Switchtec
firmware. To solve this, since Gen4, a new bit in each event header
is introduced to indicate if an event is supported by the firmware.

Link: https://lore.kernel.org/r/20211014141859.11444-6-kelvin.cao@microchip.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Add Gen4 MRPC GAS access permission check

Gen4 hardware provides new MRPC commands to read and write directly from
any address in the PCI BAR (which Microsemi refers to as GAS). Since
accessing BARs can be dangerous and break the driver, we don't want
unprivileged users to have this ability.

Therefore, require CAP_SYS_ADMIN for the local and remote GAS access MRPC
commands. Privileged processes will already have access to the BAR through
the sysfs resource file so this doesn't give userspace any capabilities it
didn't already have.

[logang@deltatee.com: rework commit message]
Link: https://lore.kernel.org/r/20200106190337.2428-11-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Add Gen4 flash information interface support

Add the new flash_info registers struct and the implementation of
ioctl_flash_part_info() for the new Gen4 hardware.

[logang@deltatee.com: rewrote commit message]
Link: https://lore.kernel.org/r/20200115035648.2578-7-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Add Gen4 system info register support

Add the Gen4-specific system info registers and ensure their usage is
guarded by a check on the device's generation.

Link: https://lore.kernel.org/r/20200115035648.2578-6-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Separate Gen3 register structures into unions

Since the sys_info and flash_info registers differ significantly in Gen4
hardware, separate out the Gen3 registers into their own structure with a
union in the main structure.

No functional changes intended.

Link: https://lore.kernel.org/r/20200115035648.2578-5-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Add 'generation' variable

Add a generation variable passed through the device ID table and test for
Gen3-specific registers. This will allow us to add Gen4 and other devices
that extend the programming model.

Link: https://lore.kernel.org/r/20200115035648.2578-3-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Rename generation-specific constants

Gen4 hardware will have different values for the SWITCHTEC_X_RUNNING and
SWITCHTEC_IOCTL_NUM_PARTITIONS, so rename them with GEN3 in their name.

No functional changes intended.

Link: https://lore.kernel.org/r/20200115035648.2578-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI/switchtec: Add support for Intercomm Notify and Upstream Error Containment

Add support for the Inter Fabric Manager Communication (Intercomm) Notify
event in PAX variants of Switchtec hardware and the Upstream Error
Containment port in the MR1 release of Gen3 firmware.

Link: https://lore.kernel.org/r/20200106190337.2428-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 288

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 263 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

switchtec: Increase PFF limit from 48 to 255

The Switchtec devices supports two PCIe Function Frameworks (PFFs) per
upstream port (one for the port itself and one for the management endoint),
and each PFF may have up to 255 ports. Previously the driver only
supported 48 of those ports, and the SWITCHTEC_IOCTL_EVENT_SUMMARY ioctl
only returned information about those 48.

Increase SWITCHTEC_MAX_PFF_CSR from 48 to 255 so the driver supports all
255 possible ports.

Rename SWITCHTEC_IOCTL_EVENT_SUMMARY and associated struct
switchtec_ioctl_event_summary to SWITCHTEC_IOCTL_EVENT_SUMMARY_LEGACY and
switchtec_ioctl_event_summary_legacy with so existing applications work
unchanged, supporting up to 48 ports.

Add replacement SWITCHTEC_IOCTL_EVENT_SUMMARY and struct
switchtec_ioctl_event_summary that new and recompiled applications support
up to 255 ports.

Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

ntb_hw_switchtec: Added support of >=4G memory windows

Current Switchtec's BAR setup registers are limited to 32bits,
corresponding to the maximum MW (memory window) size is <4G.

Increase the MW sizes with the addition of the BAR Setup Extension
Register for the upper 32bits of a 64bits MW size. This increases the MW
range to between 4K and 2^63.

Reported-by: Boris Glimcher <boris.glimcher@emc.com>
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

ntb_hw_switchtec: NT req id mapping table register entry number should be 512

The number of available NT req id mapping table entries per NTB control
register is 512. The driver mistakenly limits the number to 256.

Fix the array size of NT req id mapping table.

Fixes: c082b04c9d40 ("NTB: switchtec: Add NTB hardware register definitions")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

switchtec: Add MRPC DMA mode support

MRPC normal mode requires the host to read the MRPC command status and
output data from BAR. This results in high latency responses from the
Memory Read TLP and potential Completion Timeout (CTO).

Add support for MRPC DMA mode, including related macro definitions and data
structures and code to:

* Retrieve MRPC DMA mode version from adapter firmware
* Allocate DMA buffer, register ISR, and enable DMA during init
* Check MRPC execution status and get execution results from DMA buffer
* Release DMA buffer and disable DMA function when unloading module

MRPC DMA mode is a new feature of firmware, and the driver will fall back
to MRPC normal mode if there is no support in the legacy firmware.

Add a module parameter, "use_dma_mrpc", to select between MRPC DMA mode and
MRPC normal mode. Since the driver automatically detects DMA support in
the firmware, this parameter is just for debugging and testing.

Include <linux/io-64-nonatomic-lo-hi.h> so that readq/writeq is replaced by
two readl/writel on systems that do not support it.

Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog, simplify dma_ver check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

switchtec: Use generic PCI Vendor ID and Class Code

Move the Microsemi Switchtec PCI Vendor ID (same as
PCI_VENDOR_ID_PMC_Sierra) to pci_ids.h. Also, replace Microsemi class
constants with the standard PCI definitions.

Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
[bhelgaas: restore SPDX (I assume it was removed by mistake), remove
device ID definitions]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>

ntb_hw_switchtec: Expand PFF CSR registers

The PFF CSR registers actual mirrors the PCI configuration space
for all the ports in the switch. Previously, this was not needed by
the driver but will be used by the crosslink code to enumerate the
bus in an host-less centre partition.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups

Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.

Use following logic to determine the NT peer partition:

1) If there are 2 partitions, and the target vector is set in
the Switchtec configuration, use the partition specified in target
vector.
2) If there are 2 partitions and target vector is unset
use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
this is invalid and report an error.

Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

switchtec: Add Global Fabric Manager Server (GFMS) event

Add a new event type that is newly exposed by recent firmware. The event
will never occur if the firmware is too old. If user space tries to use
this event in an older kernel, it will just get an EINVAL which is
perfectly acceptable in the existing user space code.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

NTB: switchtec_ntb: Introduce initial NTB driver

Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

NTB: switchtec: Add link event notifier callback

In order for the Switchtec NTB code to handle link change events we
create a notifier callback in the switchtec code which gets called
whenever an appropriate event interrupt occurs.

In order to preserve userspace's ability to follow these events,
we compare the event count with a stored copy from last time we
checked.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

NTB: switchtec: Add NTB hardware register definitions

There are two additional regions: ctrl and dbmsg. The first is
for generic NTB control and memory windows. The second is for doorbells
and message registers. This patch also adds a number of related
constants for using these registers.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

NTB: switchtec: Export class symbol for use in upper layer driver

We export the class pointer symbol and add an extern define in the
Switchtec header file.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

NTB: switchtec: Move structure definitions into a common header

Create the switchtec.h header in include/linux with hardware defines
and the switchtec_dev structure. Both moved directly from switchtec.c.
This is a prep patch for creating an NTB driver for Switchtec.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>