spi: pxa2xx: Validate the correctness of the SSP type

Currently we blindly apply the SSP type value from any source of the
information. Increase robustness by validating the value before use.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Fix style of and typos in the comments and messages

Fix style of the comments and messages along with typos in them.

While at it, update Intel Copyright year.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517140351.901-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Introduce special type for Merrifield SPIs

Intel Merrifield SPI is actually more closer to PXA3xx. It has extended FIFO
(32 bytes) and additional registers to get or set FIFO thresholds.

Introduce new type for Intel Merrifield SPI host controllers and handle bigger
FIFO size.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Use pxa_ssp_enable()/pxa_ssp_disable() in the driver

There are few places that repeat the logic of pxa_ssp_enable() and
pxa_ssp_disable(). Use them instead of open coded variants.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Group Intel Quark specific definitions

DDS_RATE is Intel Quark specific definition. Move it to the rest
Intel Quark related.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Unify ifdeffery used in the headers

The two headers have quite different ifdeffery to prevent multiple inclusion.
Unify them with the pattern that in particular reflects their location.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add SSC2 and SSPSP2 SSP registers

Update list of SSP registers with SSC2 and SSPSP2. These registers are
utilized by LPT/WPT AudioDSP architecture.

While SSC2 shares the same offset (0x40) as SSACDD, description of this
register for SSP device present on mentioned AudioDSP is different so
define separate constant to avoid any ambiguity.

Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200825201743.4926-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Drop useless comment in the pxa2xx_ssp.h

No need to have file name inside file.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200826151455.55970-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Switch to use BIT() and GENMASK() in pxa2xx_ssp.h

Switch pxa2xx_ssp.h header to use BIT() and GENMASK().
It's better to read and understand. While here, correct ordering
of some definitions.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200826151455.55970-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Update header block in pxa2xx_ssp.h

We have direct users of some headers that are missed and
have header included when forward declarations are enough.

Update header block in pxa2xx_ssp.h to align with actual usage.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200826151455.55970-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add SSC2 and SSPSP2 SSP registers

Update list of SSP registers with SSC2 and SSPSP2. These registers are
utilized by LPT/WPT AudioDSP architecture.

While SSC2 shares the same offset (0x40) as SSACDD, description of this
register for SSP device present on mentioned AudioDSP is different so
define separate constant to avoid any ambiguity.

Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200825201743.4926-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: No need to keep pointer to platform device

There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.

Convert all users at the same time.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: pxa2xx: Add devicetree support

The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Use an enum for type

That seems to be the correct type.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pxa-ssp: remove .set_pll() and .set_clkdiv() callbacks

The .set_pll() and .set_clkdiv() callbacks are considered legacy and should
not be used anymore. In order to support PXA boards on DT platforms, remove
them and let the code figure out the correct dividers and PLL base
frequencies itself.

Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

ARM: pxa: change SSP DMA channels allocation

Now the dma_slave_map is available for PXA architecture, switch the SSP
device to it.

This specifically means that :
- for platform data based machines, the DMA requestor channels are
extracted from the slave map, where pxa-ssp-dai.<N> is a 1-1 match to
ssp.<N>, and the channels are either "rx" or "tx".

- for device tree platforms, the dma node should be hooked into the
pxa2xx-ac97 or pxa-ssp-dai node.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Mack <daniel@zonque.org>

spi: pxa2xx: Add support for Intel Cannonlake

Intel Cannonlake LPSS SPI has up to four chip selects per port like in
Broxton and is clocked like Sunrisepoint and Kaby Lake. Add a new type
LPSS_CNL_SSP and configuration that enable runtime chip select detection
and use the same FIFO thresholds than in Sunrisepoint.

Patch adds support for both Cannonlake SoC and PCH.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: fix indentation of the comments in header

Just for sake of readability fix the indentation of the comments in
pxa2xx_ssp.h header file.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Default thresholds to PXA configuration

Most of the devices in the supported list have PXA configuration of FIFO. In
particularly Intel Medfield and Merrifield have bigger FIFO, than it's defined
for CE4100.

Split CE4100 in the similar way how it was done for Intel Quark, i.e. prefix
definitions by CE4100 and append necessary pieces of code to switch case
conditions.

We are on safe side since those bits are ignored on all LPSS IPs.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for both chip selects on Intel Braswell

Intel Braswell LPSS SPI controller actually has two chip selects and there
is no capabilities register where this could be found out. These two chip
selects are controlled by bits which are in slightly differrent location
than Broxton has.

Braswell Windows driver also starts chip select (ACPI DeviceSelection)
numbering from 1 so translate it to be suitable for Linux as well.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for Intel Broxton

LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for Intel Sunrisepoint

Major difference in LPSS SPI between Intel Sunrisepoint PCH and earlier
platforms is an integrated DMA (iDMA) engine. iDMA is an IP that is private
for each LPSS host controller (UART/SPI/I2C). Other differences are private
register space offset, a few private registers that are in different
location and FIFO thresholds.

Intel Sunrisepoint LPSS SPI and iDMA devices are probed and registered in
MFD layer as platform devices. Here these compound devices are detected by
matching against known PCI IDs. This allows us to share
pxa2xx_spi_acpi_get_pdata() for setting up the platform data instead of
duplicating it in MFD part.

This patch adds configuration for Intel Sunrisepoint LPSS SPI, above
detection and DMA filter function that picks the DMA channel only from an
associated iDMA block.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Prepare for new Intel LPSS SPI type

Some of the Intel LPSS SPI properties will be different in upcoming
platforms compared to existing Lynxpoint and BayTrail/Braswell. LPSS SPI
private registers will be at different offset and there will be changes in
individual registers and default FIFO thresholds too.

Add configuration for these differences and use them in runtime based on
LPSS SSP type. With this change private registers offset autodetection
becomes needless.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Differentiate Intel LPSS types

Intel LPSS SPI properties differ between between platforms. Now private
registers offset 0x400 or 0x800 is autodetected but there is need to
support also other offset and handle a few other differences.

Prepare for that by splitting the LPSS_SSP type into compatible hardware
types and set it now based on PCI or ACPI ID. That type will be used to set
properties that differ between current and upcoming platforms.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add definition for Intel Quark DDS_RATE register

Intel Quark DDS_RATE register is defined only in register access macro. Add
a definition for it to common SSP register definitions for preparing to
cleanup those macros.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-pxa2xx: SPI support for Intel Quark X1000

There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.

This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ARM: pxa: fix pxa_ssp_* declarations

The functions declared in include/linux/pxa2xx_ssp.h are
defined in plat-pxa/ssp.c, which can also be built for
PLAT_MMP, but may be disabled there. This can lead to
both unresolved symbols at link time and to duplicate
symbols at compile time for random configurations.

Changing the #ifdef in the header file to match the
Kconfig symbol that decides if the file is built solves
both problems.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>

ARM: pxa: ssp: add pxa_ssp_request_of()

Add a function to lookup ssp devices from device tree. This way, users
can reference the ssp devices in order to register to them.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

spi/pxa2xx: add support for Intel Low Power Subsystem SPI

Intel LPSS SPI is pretty much the same as the PXA27xx SPI except that it
has few additional features over the original:

o FIFO depth is 256 entries
o RX FIFO has one watermark
o TX FIFO has two watermarks, low and high
o chip select can be controlled by writing to a register

The new FIFO registers follow immediately the PXA27xx registers but then there
are some additional LPSS private registers at offset 1k or 2k from the base
address. For these private registers we add new accessors that take advantage
of drv_data->lpss_base once it is resolved.

We add a new type LPSS_SSP that can be used to distinguish the LPSS devices
from others.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

spi/pxa2xx: embed the ssp_device to platform data

The spi-pxa2xx-pci glue driver had to implement pxa_ssp_request()/free() in
order to support the spi-pxa2xx platform driver. Since the ACPI enabled
platforms can use the same platform driver we would need to implement
pxa_ssp_request()/free() in some central place that can be shared by the
ACPI and PCI glue code.

Instead of doing that we can make pxa_ssp_request()/free() to be available
only when CONFIG_ARCH_PXA is set. On other arches these are being stubbed
out in preference to passing the ssp_device from the platform data
directly.

We also change the SPI bus number to be taken from ssp->port_id instead of
platform device id. This way the supporting code that passes the ssp can
decide the number (or it can set it to the same as pdev->id).

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix pxa-ssp compiling issue under mach-mmp

pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.

Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ARM: MMP: add pxa910-ssp into ssp_id_table

add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.

Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix common misspellings

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

spi/pxa2xx: Add chipselect support for Sodaville

The SPI core on Sodaville supports chip selects. Its configuration
moved into the SSSR register at bit 0 and 1. Thus Sodaville can be hooked
up with up to 4 devices.
This patch ensures that the bits which are otherwiese reserved are only
touched on Sodaville and not on any other PXAs. Also it makes sure that
the status register does not lose the CS information while clearing the
ROR bit.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>

spi/pxa2xx: Consider CE4100's FIFO depth

For PXA the default threshold is FIFO_DEPTH / 2. Adjust this value for
CE4100.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>

arm/pxa2xx: reorgazine SSP and SPI header files

The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.

This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>