net: hns3: fix VF reset fail issue

Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. We think firmware watchdog initialization is completed
before VF clear the interrupt source. However, firmware initialization
may not complete early. So VF will receive multiple reset interrupts
and fail to reset.

So we add delay before VF interrupt source and 5 ms delay
is enough to avoid second reset interrupt.

Fixes: 427900d27d86 ("net: hns3: fix the timing issue of VF clearing interrupt sources")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: move dump regs function to a separate file

The dump register function is being refactored.
The first step in refactoring is put the dump regs function
into a separate file.

Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add byte order conversion for PF to VF mailbox message

Currently, hns3 mailbox processing between PF and VF missed to convert
message byte order and use data type u16 instead of __le16 for mailbox
data process. These processes may cause problems between different
architectures.

So this patch uses __le16/__le32 data type to define mailbox data
structures. To be compatible with old hns3 driver, these structures use
one-byte alignment. Then byte order conversions are added to mailbox
messages from PF to VF.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for TX push mode

For the device that supports the TX push capability, the BD can
be directly copied to the device memory. However, due to hardware
restrictions, the push mode can be used only when there are no
more than two BDs, otherwise, the doorbell mode based on device
memory is used.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor VF tqp stats APIs with new common tqp stats APIs

This patch firstly uses new tqp struct(hclge_comm_tqp) and removes the
old VF tqp struct(hclgevf_tqp). All the tqp stats members used in VF module
are modified according to the new hclge_comm_tqp.

Secondly VF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in VF are deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor VF rss set APIs with new common rss set APIs

This patch uses new common rss set APIs to replace the old APIs in VF rss
module and removes those old rss set APIs. The related macros in VF are
also modified.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor VF rss get APIs with new common rss get APIs

This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclgevf_dev and deletes the original child rss parameter
member(hclgevf_rss_cfg). All the rss parameter members used in VF rss
module is modified according to the new hclge_comm_rss_cfg.

Secondly VF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in VF are deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor VF cmdq init and uninit APIs with new common APIs

This patch uses common cmdq init and uninit APIs to replace the old APIs in
VF cmdq module init and uninit module. Then the old VF init and uninit
APIs is deleted.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor hclgevf_cmd_send with new hclge_comm_cmd_send API

This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclgevf_hw and deletes the old hardware description child
members. All the hclgevf_hw variables used in VF module is modified
according to the new hclgevf_hw.

Secondly hclgevf_cmd_send is refactored to use hclge_comm_cmd_send APIs.
The old functions called by hclgevf_cmd_send are all deleted. Still we kept
hclgevf_cmd_send to avoid too many meaningless modifications.

Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix kernel crash when unload VF while it is being reset

When fully configure VLANs for a VF, then unload the VF while
triggering a reset to PF, will cause a kernel crash because the
irq is already uninit.

[ 293.177579] ------------[ cut here ]------------
[ 293.183502] kernel BUG at drivers/pci/msi.c:352!
[ 293.189547] Internal error: Oops - BUG: 0 [#1] SMP
......
[ 293.390124] Workqueue: hclgevf hclgevf_service_task [hclgevf]
[ 293.402627] pstate: 80c00009 (Nzcv daif +PAN +UAO)
[ 293.414324] pc : free_msi_irqs+0x19c/0x1b8
[ 293.425429] lr : free_msi_irqs+0x18c/0x1b8
[ 293.436545] sp : ffff00002716fbb0
[ 293.446950] x29: ffff00002716fbb0 x28: 0000000000000000
[ 293.459519] x27: 0000000000000000 x26: ffff45b91ea16b00
[ 293.472183] x25: 0000000000000000 x24: ffffa587b08f4700
[ 293.484717] x23: ffffc591ac30e000 x22: ffffa587b08f8428
[ 293.497190] x21: ffffc591ac30e300 x20: 0000000000000000
[ 293.509594] x19: ffffa58a062a8300 x18: 0000000000000000
[ 293.521949] x17: 0000000000000000 x16: ffff45b91dcc3f48
[ 293.534013] x15: 0000000000000000 x14: 0000000000000000
[ 293.545883] x13: 0000000000000040 x12: 0000000000000228
[ 293.557508] x11: 0000000000000020 x10: 0000000000000040
[ 293.568889] x9 : ffff45b91ea1e190 x8 : ffffc591802d0000
[ 293.580123] x7 : ffffc591802d0148 x6 : 0000000000000120
[ 293.591190] x5 : ffffc591802d0000 x4 : 0000000000000000
[ 293.602015] x3 : 0000000000000000 x2 : 0000000000000000
[ 293.612624] x1 : 00000000000004a4 x0 : ffffa58a1e0c6b80
[ 293.623028] Call trace:
[ 293.630340] free_msi_irqs+0x19c/0x1b8
[ 293.638849] pci_disable_msix+0x118/0x140
[ 293.647452] pci_free_irq_vectors+0x20/0x38
[ 293.656081] hclgevf_uninit_msi+0x44/0x58 [hclgevf]
[ 293.665309] hclgevf_reset_rebuild+0x1ac/0x2e0 [hclgevf]
[ 293.674866] hclgevf_reset+0x358/0x400 [hclgevf]
[ 293.683545] hclgevf_reset_service_task+0xd0/0x1b0 [hclgevf]
[ 293.693325] hclgevf_service_task+0x4c/0x2e8 [hclgevf]
[ 293.702307] process_one_work+0x1b0/0x448
[ 293.710034] worker_thread+0x54/0x468
[ 293.717331] kthread+0x134/0x138
[ 293.724114] ret_from_fork+0x10/0x18
[ 293.731324] Code: f940b000 b4ffff00 a903e7b8 f90017b6 (d4210000)

This patch fixes the problem by waiting for the VF reset done
while unloading the VF.

Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix ROCE base interrupt vector initialization bug

Currently, NIC init ROCE interrupt vector with MSIX interrupt. But ROCE use
pci_irq_vector() to get interrupt vector, which adds the relative interrupt
vector again and gets wrong interrupt vector.

So fixes it by assign relative interrupt vector to ROCE instead of MSIX
interrupt vector and delete the unused struct member base_msi_vector
declaration of hclgevf_dev.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: ignore reset event before initialization process is done

Currently, if there is a reset event triggered by RAS during device in
initialization process, driver may run reset process concurrently with
initialization process. In this case, it may cause problem. For example,
the RSS indirection table may has not been alloc memory in initialization
process yet, but it is used in reset process, it will cause a call trace
like this:

[61228.744836] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
[61228.897677] Workqueue: hclgevf hclgevf_service_task [hclgevf]
[61228.911390] pstate: 40400009 (nZcv daif +PAN -UAO -TCO BTYPE=--)
[61228.918670] pc : hclgevf_set_rss_indir_table+0xb4/0x190 [hclgevf]
[61228.927812] lr : hclgevf_set_rss_indir_table+0x90/0x190 [hclgevf]
[61228.937248] sp : ffff8000162ebb50
[61228.941087] x29: ffff8000162ebb50 x28: ffffb77add72dbc0 x27: ffff0820c7dc8080
[61228.949516] x26: 0000000000000000 x25: ffff0820ad4fc880 x24: ffff0820c7dc8080
[61228.958220] x23: ffff0820c7dc8090 x22: 00000000ffffffff x21: 0000000000000040
[61228.966360] x20: ffffb77add72b9c0 x19: 0000000000000000 x18: 0000000000000030
[61228.974646] x17: 0000000000000000 x16: ffffb77ae713feb0 x15: ffff0820ad4fcce8
[61228.982808] x14: ffffffffffffffff x13: ffff8000962eb7f7 x12: 00003834ec70c960
[61228.991990] x11: 00e0fafa8c206982 x10: 9670facc78a8f9a8 x9 : ffffb77add717530
[61229.001123] x8 : ffff0820ad4fd6b8 x7 : 0000000000000000 x6 : 0000000000000011
[61229.010249] x5 : 00000000000cb1b0 x4 : 0000000000002adb x3 : 0000000000000049
[61229.018662] x2 : ffff8000162ebbb8 x1 : 0000000000000000 x0 : 0000000000000480
[61229.027002] Call trace:
[61229.030177] hclgevf_set_rss_indir_table+0xb4/0x190 [hclgevf]
[61229.039009] hclgevf_rss_init_hw+0x128/0x1b4 [hclgevf]
[61229.046809] hclgevf_reset_rebuild+0x17c/0x69c [hclgevf]
[61229.053862] hclgevf_reset_service_task+0x4cc/0xa80 [hclgevf]
[61229.061306] hclgevf_service_task+0x6c/0x630 [hclgevf]
[61229.068491] process_one_work+0x1dc/0x48c
[61229.074121] worker_thread+0x15c/0x464
[61229.078562] kthread+0x168/0x16c
[61229.082873] ret_from_fork+0x10/0x18
[61229.088221] Code: 7900e7f6 f904a683 d503201f 9101a3e2 (38616b43)
[61229.095357] ---[ end trace 153661a538f6768c ]---

To fix this problem, don't schedule reset task before initialization
process is done.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: merge some repetitive macros

There are some repetitive macros have same meaning and value, this patch
merges them to make code clean.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove redundant param mbx_event_pending

This patch removes the redundant param mbx_event_pending.

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for registering devlink for VF

Add devlink register support for HNS3 ethernet VF driver.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix GRO configuration error after reset

The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: add query basic info support for VF

There are some features of VF depend on PF, so it's necessary
for VF to know whether PF supports. For compatibility, modify
the mailbox HCLGE_MBX_GET_TCINFO, extend its function, use to
get the basic information of PF, including mailbox api version
and PF capabilities.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: support RXD advanced layout

Currently, the driver gets packet type by parsing the
L3_ID/L4_ID/OL3_ID/OL4_ID from RX descriptor, it's
time-consuming.

Now some new devices support RXD advanced layout, which combines
previous OL3_ID/OL4_ID to 8bit ptype field, so the driver gets
packet type by looking up only one table, and L3_ID/L4_ID become
reserved fields.

Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by
default. This patch provides basic function: identify and enable
the RXD advanced layout, and refactor out hns3_rx_checksum() by
using ptype table to handle RX checksum if supported.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: cleanup inappropriate spaces in struct hlcgevf_tqp_stats

Modify some inappropriate spaces in comments of struct
hlcgevf_tqp_stats.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: VF not request link status when PF support push link status feature

To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused code of vmdq

Vmdq is not supported yet, the num_vmdq_vport is always 0,
it's a bit confusing when using the num_vport, so remove
these unused codes of vmdq.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for obtaining the maximum frame size

Since the newer hardware may supports different frame size,
so add support to obtain the capability from the firmware
instead of the fixed value.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: RSS indirection table use device specification

As RSS indirection table size may be different in different
hardware. Instead of using macro, this value is better to use
device specification which querying from firmware.

BTW, RSS indirection table should be allocated by the queried
size instead the static array.

.get_rss_indir_size in struct hnae3_ae_ops is not used now,
so remove it as well.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: fix incorrect handling of sctp6 rss tuple

For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.

Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for mapping device memory

For device who has device memory accessed through the PCI BAR4,
IO descriptor push of NIC and direct WQE(Work Queue Element) of
RoCE will use this device memory, so add support for mapping
this device memory, and add this info to the RoCE client whose
new feature needs.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: hns3: Add RoCE VF reset support

Add RoCE VF client reset support by notifying the RoCE VF client
when hns3 VF is resetting and adding a interface to query whether
CMDQ is ready to work.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix an incorrect comment for num_tqps in struct hclgevf_dev

struct hclgevf_dev stands for VF device, its field num_tqps
indicates the number of VF's task queue pairs, so the comment
is incorrect, replace 'PF' with 'VF'.

Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove two duplicated register macros in hclgevf_main.h

HCLGEVF_CMDQ_INTR_SRC_REG and HCLGEVF_CMDQ_INTR_STS_REG are same
as HCLGEVF_VECTOR0_CMDQ_SRC_REG and HCLGEVF_VECTOR0_CMDQ_STAT_REG,
replace the former with the latter, and rename macro
HCLGEVF_VECTOR0_CMDQ_STAT_REG since 'stat' is not abbreviation of
'state'.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the promisc mode setting

As the HNS3 driver doesn't update the MAC address directly in
function hns3_set_rx_mode() now, it can't know whether the
MAC table is full from __dev_uc_sync() and __dev_mc_sync(),
so it's senseless to handle the overflow promisc here.

This patch removes the handle of overflow promisc from function
hns3_set_rx_mode(), and updates the promisc mode in the service
task.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the MAC address configure

Currently, the HNS3 driver sync and unsync MAC address in function
hns3_set_rx_mode(). For PF, it adds and deletes MAC address directly
in the path of dev_set_rx_mode(). If failed, it won't retry until
next calling of hns3_set_rx_mode(). On the other hand, if request
add and remove a same address many times at a short interval, each
request must be done one by one, can't be merged. For VF, it sends
mailbox messages to PF to request adding or deleting MAC address in
the path of function hns3_set_rx_mode(), no matter the address is
configured success.

This patch refines it by recording the MAC address in function
hns3_set_rx_mode(), and updating MAC address in the service task.
If failed, it will retry by the next calling of periodical service
task. It also uses some state to mark the state of each MAC address
in the MAC list, which can help merge configure request for a same
address. With these changes, when global reset or IMP reset occurs,
we can restore the MAC table with the MAC list.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the mailbox message between PF and VF

For making the code more readable, this adds several new
structure to replace the msg field in structure
hclge_mbx_vf_to_pf_cmd and hclge_mbx_pf_to_vf_cmd.
Also uses macro to instead of some magic number.

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: refactor the procedure of VF FLR

Currently, the actual work of VF FLR is handled in the reset task,
which is asynchronous. So in some case, if the preparing and
rebuilding are not done, then the VF FLR will trigger some problems,
for example, makes hardware go into chaos.

So this patch separates the process of VF FLR from reset task, and
adds a semaphore to serialize this reset and others.

When FLR's preparing fails, if there has other higher level reset
pending or failing times less than the HCLGE_FLR_RETRY_CNT, this
preparing should be retried, otherwise it will get into a wrong state.

BTW, while the hardware reports misc interrupt during pcie_flr(),
the driver can not receive this interrupt anymore, so disable it
when hclgevf_flr_prepare() return, and re-enable it when enter
hclgevf_flr_done().

Avoid declaring internal function hclgevf_enable_vector(), this patch
also moves its definition forward, and removes unused enum
hnae3_flr_state.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: modify the IRQ name of misc vectors

The misc IRQ of all the devices have the same name, so it's
hard to find the right misc IRQ of the device.

This patch modifies the misc IRQ names as "hclge/hclgevf"-misc-
"pci name". And now the IRQ name is not related to net device
name anymore, so change the HNAE3_INT_NAME_LEN to 32 bytes, and
that is enough.

Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: do not schedule the periodic task when reset fail

service_task will be scheduled per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.

This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unnecessary work in hclgevf_main

There are four work (mbx_service_task, service_task,
rst_service_task and keep_alive_task)in the hclgevf module,
mbx_service_task is for handling mailbox issue, service_task is
for periodic management issue and rst_service_task is for reset
related issue, keep_alive_task is used to keepalive between PF
and VF, which can be done in a single work.

This patch removes the mbx_service_task, rst_service_task and
keep_alive_task, and moves the related handling to the
service_task work in order to remove concurrency between the four
work and to improve efficiency.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: schedule hclgevf_service by using delayed workqueue

Currently, a timer is defined to schedule hclgevf_service per
second. To simplify the code, this patch uses the delayed work
instead of timer to schedule hclgevf_serive.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused macros

The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used. I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix mis-counting IRQ vector numbers issue

Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).

This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.

This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for configuring VF MAC from the host

This patch adds support of configuring VF MAC from the host
for the HNS3 driver.

BTW, the parameter init in the hns3_init_mac_addr is
unnecessary now, since the MAC address will not read from
NCL_CONFIG when doing reset, so it should be removed,
otherwise it will affect VF's MAC address initialization.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: refine some macro definitions

Macro arguments should be enclosed in parentheses, in case of
expression argument, but parentheses of pure number in macro
definition should be removed for simplicity.

Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix interrupt clearing error for VF

Currently, VF driver has two kinds of interrupts, reset & CMDQ RX.
For revision 0x21, according to the UM, each interrupt should be
cleared by write 0 to the corresponding bit, but the implementation
writes 0 to the whole register in fact, it will clear other
interrupt at the same time, then the VF will loss the interrupt.
But for revision 0x20, this interrupt clear register is a read &
write register, for compatible, we just keep the old implementation
for 0x20.

This patch fixes it, also, adds a new register for reading the interrupt
status according to hardware user manual.

Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: clear reset interrupt status in hclge_irq_handle()

Currently, the reset interrupt is cleared in the reset task, which
is too late. Since, when the hardware finish the previous reset,
it can begin to do a new global/IMP reset, if this new coming reset
type is same as the previous one, the driver will clear them together,
then driver can not get that there is another reset, but the hardware
still wait for the driver to deal with the second one.

So this patch clears PF's reset interrupt status in the
hclge_irq_handle(), the hardware waits for handshaking from
driver before doing reset, so the driver and hardware deal with reset
one by one.

BTW, when VF doing global/IMP reset, it reads PF's reset interrupt
register to get that whether PF driver's re-initialization is done,
since VF's re-initialization should be done after PF's. So we add
a new command and a register bit to do that. When VF receive reset
interrupt, it sets up this bit, and PF finishes re-initialization
send command to clear this bit, then VF do re-initialization.

Fixes: 4ed340ab8f49 ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: re-schedule reset task while VF reset fail

The VF reset may fail for some probabilistic reasons,
such as wait for hardware reset timeout, wait for mailbox
response timeout, so this patch tries to re-schedule the
reset task when the number of reset failing is under
HCLGEVF_RESET_MAX_FAIL_CNT. This patch also add a function
hclgevf_reset_err_handle() to handle the reset failing.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: sync VLAN filter entries when kill VLAN ID failed

When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.

This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.

Fixes: 44e626f720c3 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use macros instead of magic numbers

This patch adds some macros instead of magic numbers in serval places

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: stop schedule reset service while unloading driver

When unloading driver, the reset task should not be scheduled
anymore. If disable IRQ before cancel ongoing reset task,
the IRQ may be re-enabled by the reset task.

This patch uses HCLGE_STATE_REMOVING/HCLGEVF_STATE_REMOVING
flag to indicate that the driver is unloading, and we should
stop new coming reset service to be scheduled, otherwise,
reset service will access some resource which has been freed
by unloading.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: use HCLGEVF_STATE_NIC_REGISTERED to indicate VF NIC client has registered

When VF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGEVF_STATE_NIC_REGISTERED
to indicate that. And before calling VF NIC client's uninit_instance(),
we clear this state.

So any operation of VF NIC client from HCLGEVF is not allowed if this
state is not set.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support for multiple media type

Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.

The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes

In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add queue's statistics update to service task

This patch updates VF's TQP statistic info in the service task,
and adds a limitation to prevent update too frequently.

Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset statistics for VF

This patch adds some statistics for VF reset.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix set port based VLAN issue for VF

In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.

This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.

Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add support to config depth for tx|rx ring separately

This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".

Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix the problem that the supported port is empty

Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.

This patch fixes it.

Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Support "ethtool -d" for HNS3 VF driver

This patch adds "ethtool -d" support for HNS3 VF Driver.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add vport alive state checking support

Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.

This patch adds vport alive state checking support, in order
to support the above scenario.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add PCIe FLR support for VF

This patch implements the .reset_prepare and .reset_done
ops from pci framework to support the VF FLR.

This patch uses hclgevf_set_def_reset_request() and
hclgevf_reset_event() to handle FLR, so when
hdev->default_reset_request is non zero, it means there is
some reset requseted by hclgevf_set_def_reset_request() need
to be processed. Also get the hdev from the ae_dev because
hclgevf_reset_event is called with handle being NULL.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: do VF's pci re-initialization while PF doing FLR

While doing PF FLR, VF's PCIe configuration space will be cleared, so
the pci and vector of VF should be re-initialized in the VF's reset
process while PF doing FLR.

Also, this patch fixes some memory not freed problem when pci
re-initialization is done during reset process.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: stop handling command queue while resetting VF

According to hardware's description, after the reset occurs, the driver
needs to re-initialize the command queue before sending and receiving
any commands. Therefore, the VF's driver needs to identify the command
queue needs to re-initialize with HCLGEVF_STATE_CMD_DISABLE, and does
not allow sending or receiving commands before the re-initialization.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset handling for VF when doing Core/Global/IMP reset

When a Core/Global/IMP reset occurs, the hardware sets the reset status
register of all PF/VF and reports a reset interrupt to all PF/VF and
firmware.

When receiving the reset interrupt:
1. The firmware will wait for 100 ms before resetting the hardware and
clear the reset status register of all PF when hardware reset is done.
2. The PF/VF driver needs to down the netdev within 100 ms and then wait
for hardware reset to finish.
3. After firmware clearing the reset status register of all PF, the PF
driver reinitializes the hardware and clear the reset status register
of it's VF.
4. After PF driver clearing the reset status register of VF, the VF driver
reinitializes the hardware.

This patch mainly add handling for the step 4.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset handling for VF when doing PF reset

When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.

Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.

Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: adjust VF's reset process

Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.

This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.

Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.

hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add reset_hdev to reinit the hdev in VF's reset process

When doing reset, the reset handling function only need to
reinitialize hardware, it makes sense to add a function to
do that job. Also the error handling of hclgevf_init_hdev is
different when it is used in reset process.

This patch adds reset_hdev to reinitialize hardware when resetting.
Also, this patch removes the hclgevf_dev_ongoing_full_reset because
it is unused now.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: move some reset information from hnae3_handle into hclge_dev/hclgevf_dev

Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: provide some interface & information for the client

The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.

So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.

Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add set_default_reset_request in the hnae3_ae_ops

Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.

There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add RSS tuples support for VF

This patch adds RSS tuple support for VF in revision
0x21.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Drop depricated mta table support

For mta table support has been dropped, remove the code for mta table.

Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add get_media_type ops support for VF

This patch adds the ops of get_media_type support for VF.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix MSIX allocation issue for VF

The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.

Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Optimize the VF's process of updating multicast MAC

In the update flow of the new PF driver, if a multicast address is in mta
table, the VF deletion action will not take effect.

This patch adds the VF adaptation according to the new flow of PF'driver.

Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix for hns3 module is loaded multiple times problem

If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:

[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34

This patch fixes it by adding module version info.

Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Changes to support ARQ(Asynchronous Receive Queue)

Current mailbox CRQ could consists of both synchronous and async
responses from the PF. Synchronous responses are time critical
and should be handed over to the waiting tasks/context as quickly
as possible otherwise timeout occurs.

Above problem gets accentuated if CRQ consists of even single
async message. Hence, it is important to have quick handling of
synchronous messages and maybe deferred handling of async messages
This patch introduces separate ARQ(async receive queues) for the
async messages. These messages are processed later with repsect
to mailbox task while synchronous messages still gets processed
in context to mailbox interrupt.

ARQ is important as VF reset introduces some new async messages
like MBX_ASSERTING_RESET which adds up to the presssure on the
responses for synchronousmessages and they timeout even more
quickly.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support to re-initialize the hclge device

After the hardware reset we should re-fetch the configuration from
PF like queue info and tc info. This might have impact on allocations
made like that of TQPs. Hence, we should release all such allocations
and re-allocate fresh according to new fetched configuration after
reset.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add support to reset the enet/ring mgmt layer

After VF driver knows that hardware reset has been performed
successfully, it should proceed ahead and reset the enet layer.
This primarily consists of bringing down interface, clearing
TX/RX rings, disassociating vectors from ring etc.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add VF Reset device state and its handling

This introduces the hclge device reset states of "requested" and
"pending" and also its handling in context to Reset Service Task.

Device gets into requested state because of any VF reset request
asserted from upper layers, for example due to watchdog timeout
expiration. Requested state would result in eventually forwarding
the VF reset request to PF which would actually reset the VF.

Device will get into pending state if:
1. VF receives the acknowledgement from PF for the VF reset
request it originally sent to PF.
2. Reset Service Task detects that after asserting VF reset for
certain times the data-path is not working and device then
decides to assert full VF reset(this means also resetting the
PCIe interface).
3. PF intimates the VF that it has undergone reset.
Pending state would result in VF to poll for hardware reset
completion status and then resetting the stack/enet layer, which
in turn means reinitializing the ring management/enet layer.

Note: we would be adding support of 3. later as a separate patch.
This decision should not affect VF reset as its event handling
is generic in nature.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add VF Reset Service Task to support event handling

VF reset would involve handling of different reset related events
from the stack, physical function, mailbox etc. Reset service task
would be used in servicing such reset event requests and later
handling the hardware completions waits and initiating the stack
resets.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add querying speed and duplex support to VF

This patch adds support for querying speed and duplex by ethtool ethX
to VF.

Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support

This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.

This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.

Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>