net: dsa: ar9331: Use maple tree register cache

We now have a regmap cache which uses a maple tree to store the register
state, this is a more modern data structure and the regmap level code
using it makes a number of assumptions better tuned for modern hardware
than those made by the rbtree cache type that the at9331 driver uses.
Switch the ar9331 driver to use the more modern data structure.

This should have minimal practical impact, it's mainly code
modernisation.

Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: ar9331: Use explict flags for regmap single read/write

The at9331 is only able to read or write a single register at once. The
driver has a custom regmap bus and chooses to tell the regmap core about
this by reporting the maximum transfer sizes rather than the explicit
flags that exist at the regmap level. Since there are a number of
problems with the raw transfer limits and the regmap level flags are
better integrated anyway convert the driver to use the flags.

No functional change.

Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca8k: remove unnecessary (void*) conversions

Pointer variables of (void*) type do not require type cast.

Signed-off-by: Atin Bainada <hi@atinb.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: ar9331: remove unnecessary dev_set_drvdata()

Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: ar9331: add support for pause stats

Add support for pause stats.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: ar9331: fix potential dead lock on mdio access

Rework MDIO locking to avoid potential circular locking:

WARNING: possible circular locking dependency detected
5.19.0-rc1-ar9331-00017-g3ab364c7c48c #5 Not tainted
------------------------------------------------------
kworker/u2:4/68 is trying to acquire lock:
81f3c83c (ar9331:1005:(&ar9331_mdio_regmap_config)->lock){+.+.}-{4:4}, at: regmap_write+0x50/0x8c

but task is already holding lock:
81f60494 (&bus->mdio_lock){+.+.}-{4:4}, at: mdiobus_read+0x40/0x78

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&bus->mdio_lock){+.+.}-{4:4}:
lock_acquire+0x2d4/0x360
__mutex_lock+0xf8/0x384
mutex_lock_nested+0x2c/0x38
mdiobus_write+0x44/0x80
ar9331_sw_bus_write+0x50/0xe4
_regmap_raw_write_impl+0x604/0x724
_regmap_bus_raw_write+0x9c/0xb4
_regmap_write+0xdc/0x1a0
_regmap_update_bits+0xf4/0x118
_regmap_select_page+0x108/0x138
_regmap_raw_read+0x25c/0x288
_regmap_bus_read+0x60/0x98
_regmap_read+0xd4/0x1b0
_regmap_update_bits+0xc4/0x118
regmap_update_bits_base+0x64/0x8c
ar9331_sw_irq_bus_sync_unlock+0x40/0x6c
__irq_set_handler+0x7c/0xac
ar9331_sw_irq_map+0x48/0x7c
irq_domain_associate+0x174/0x208
irq_create_mapping_affinity+0x1a8/0x230
ar9331_sw_probe+0x22c/0x388
mdio_probe+0x44/0x70
really_probe+0x200/0x424
__driver_probe_device+0x290/0x298
driver_probe_device+0x54/0xe4
__device_attach_driver+0xe4/0x130
bus_for_each_drv+0xb4/0xd8
__device_attach+0x104/0x1a4
bus_probe_device+0x48/0xc4
device_add+0x600/0x800
mdio_device_register+0x68/0xa0
of_mdiobus_register+0x2bc/0x3c4
ag71xx_probe+0x6e4/0x984
platform_probe+0x78/0xd0
really_probe+0x200/0x424
__driver_probe_device+0x290/0x298
driver_probe_device+0x54/0xe4
__driver_attach+0x17c/0x190
bus_for_each_dev+0x8c/0xd0
bus_add_driver+0x110/0x228
driver_register+0xe4/0x12c
do_one_initcall+0x104/0x2a0
kernel_init_freeable+0x250/0x288
kernel_init+0x34/0x130
ret_from_kernel_thread+0x14/0x1c

-> #0 (ar9331:1005:(&ar9331_mdio_regmap_config)->lock){+.+.}-{4:4}:
check_noncircular+0x88/0xc0
__lock_acquire+0x10bc/0x18bc
lock_acquire+0x2d4/0x360
__mutex_lock+0xf8/0x384
mutex_lock_nested+0x2c/0x38
regmap_write+0x50/0x8c
ar9331_sw_mbus_read+0x74/0x1b8
__mdiobus_read+0x90/0xec
mdiobus_read+0x50/0x78
get_phy_device+0xa0/0x18c
fwnode_mdiobus_register_phy+0x120/0x1d4
of_mdiobus_register+0x244/0x3c4
devm_of_mdiobus_register+0xe8/0x100
ar9331_sw_setup+0x16c/0x3a0
dsa_register_switch+0x7dc/0xcc0
ar9331_sw_probe+0x370/0x388
mdio_probe+0x44/0x70
really_probe+0x200/0x424
__driver_probe_device+0x290/0x298
driver_probe_device+0x54/0xe4
__device_attach_driver+0xe4/0x130
bus_for_each_drv+0xb4/0xd8
__device_attach+0x104/0x1a4
bus_probe_device+0x48/0xc4
deferred_probe_work_func+0xf0/0x10c
process_one_work+0x314/0x4d4
worker_thread+0x2a4/0x354
kthread+0x134/0x13c
ret_from_kernel_thread+0x14/0x1c

other info that might help us debug this:

Possible unsafe locking scenario:

CPU0 CPU1
---- ----
lock(&bus->mdio_lock);
lock(ar9331:1005:(&ar9331_mdio_regmap_config)->lock);
lock(&bus->mdio_lock);
lock(ar9331:1005:(&ar9331_mdio_regmap_config)->lock);

*** DEADLOCK ***

5 locks held by kworker/u2:4/68:
#0: 81c04eb4 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x1e4/0x4d4
#1: 81f0de78 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x1e4/0x4d4
#2: 81f0a880 (&dev->mutex){....}-{4:4}, at: __device_attach+0x40/0x1a4
#3: 80c8aee0 (dsa2_mutex){+.+.}-{4:4}, at: dsa_register_switch+0x5c/0xcc0
#4: 81f60494 (&bus->mdio_lock){+.+.}-{4:4}, at: mdiobus_read+0x40/0x78

stack backtrace:
CPU: 0 PID: 68 Comm: kworker/u2:4 Not tainted 5.19.0-rc1-ar9331-00017-g3ab364c7c48c #5
Workqueue: events_unbound deferred_probe_work_func
Stack : 00000056 800d4638 81f0d64c 00000004 00000018 00000000 80a20000 80a20000
80937590 81ef3858 81f0d760 3913578a 00000005 8045e824 81f0d600 a8db84cc
00000000 00000000 80937590 00000a44 00000000 00000002 00000001 ffffffff
81f0d6a4 80982d7c 0000000f 20202020 80a20000 00000001 80937590 81ef3858
81f0d760 3913578a 00000005 00000005 00000000 03bd0000 00000000 80e00000
...
Call Trace:
[<80069db0>] show_stack+0x94/0x130
[<8045e824>] dump_stack_lvl+0x54/0x8c
[<800c7fac>] check_noncircular+0x88/0xc0
[<800ca068>] __lock_acquire+0x10bc/0x18bc
[<800cb478>] lock_acquire+0x2d4/0x360
[<807b84c4>] __mutex_lock+0xf8/0x384
[<807b877c>] mutex_lock_nested+0x2c/0x38
[<804ea640>] regmap_write+0x50/0x8c
[<80501e38>] ar9331_sw_mbus_read+0x74/0x1b8
[<804fe9a0>] __mdiobus_read+0x90/0xec
[<804feac4>] mdiobus_read+0x50/0x78
[<804fcf74>] get_phy_device+0xa0/0x18c
[<804ffeb4>] fwnode_mdiobus_register_phy+0x120/0x1d4
[<805004f0>] of_mdiobus_register+0x244/0x3c4
[<804f0c50>] devm_of_mdiobus_register+0xe8/0x100
[<805017a0>] ar9331_sw_setup+0x16c/0x3a0
[<807355c8>] dsa_register_switch+0x7dc/0xcc0
[<80501468>] ar9331_sw_probe+0x370/0x388
[<804ff0c0>] mdio_probe+0x44/0x70
[<804d1848>] really_probe+0x200/0x424
[<804d1cfc>] __driver_probe_device+0x290/0x298
[<804d1d58>] driver_probe_device+0x54/0xe4
[<804d2298>] __device_attach_driver+0xe4/0x130
[<804cf048>] bus_for_each_drv+0xb4/0xd8
[<804d200c>] __device_attach+0x104/0x1a4
[<804d026c>] bus_probe_device+0x48/0xc4
[<804d108c>] deferred_probe_work_func+0xf0/0x10c
[<800a0ffc>] process_one_work+0x314/0x4d4
[<800a17fc>] worker_thread+0x2a4/0x354
[<800a9a54>] kthread+0x134/0x13c
[<8006306c>] ret_from_kernel_thread+0x14/0x1c
[

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220616112550.877118-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: ar9331: convert to phylink_generic_validate()

Populate the supported interfaces and MAC capabilities for the AR9331
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: ar9331: register the mdiobus under devres

As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")

mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.

The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.

If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.

So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.

The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.

Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: convert users of bitmap_foo() to linkmode_foo()

This converts instances of
bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS)
to
linkmode_foo(args...)

I manually fixed up some lines to prevent them from being excessively
long. Otherwise, this change was generated with the following semantic
patch:

// Generated with
// echo linux/linkmode.h > includes
// git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \
// | sort | uniq | tee new_includes | wc -l && mv new_includes includes
// and repeating until the number stopped going up
@i@
@@

(
#include <linux/acpi_mdio.h>
|
#include <linux/brcmphy.h>
|
#include <linux/dsa/loop.h>
|
#include <linux/dsa/sja1105.h>
|
#include <linux/ethtool.h>
|
#include <linux/ethtool_netlink.h>
|
#include <linux/fec.h>
|
#include <linux/fs_enet_pd.h>
|
#include <linux/fsl/enetc_mdio.h>
|
#include <linux/fwnode_mdio.h>
|
#include <linux/linkmode.h>
|
#include <linux/lsm_audit.h>
|
#include <linux/mdio-bitbang.h>
|
#include <linux/mdio.h>
|
#include <linux/mdio-mux.h>
|
#include <linux/mii.h>
|
#include <linux/mii_timestamper.h>
|
#include <linux/mlx5/accel.h>
|
#include <linux/mlx5/cq.h>
|
#include <linux/mlx5/device.h>
|
#include <linux/mlx5/driver.h>
|
#include <linux/mlx5/eswitch.h>
|
#include <linux/mlx5/fs.h>
|
#include <linux/mlx5/port.h>
|
#include <linux/mlx5/qp.h>
|
#include <linux/mlx5/rsc_dump.h>
|
#include <linux/mlx5/transobj.h>
|
#include <linux/mlx5/vport.h>
|
#include <linux/of_mdio.h>
|
#include <linux/of_net.h>
|
#include <linux/pcs-lynx.h>
|
#include <linux/pcs/pcs-xpcs.h>
|
#include <linux/phy.h>
|
#include <linux/phy_led_triggers.h>
|
#include <linux/phylink.h>
|
#include <linux/platform_data/bcmgenet.h>
|
#include <linux/platform_data/xilinx-ll-temac.h>
|
#include <linux/pxa168_eth.h>
|
#include <linux/qed/qed_eth_if.h>
|
#include <linux/qed/qed_fcoe_if.h>
|
#include <linux/qed/qed_if.h>
|
#include <linux/qed/qed_iov_if.h>
|
#include <linux/qed/qed_iscsi_if.h>
|
#include <linux/qed/qed_ll2_if.h>
|
#include <linux/qed/qed_nvmetcp_if.h>
|
#include <linux/qed/qed_rdma_if.h>
|
#include <linux/sfp.h>
|
#include <linux/sh_eth.h>
|
#include <linux/smsc911x.h>
|
#include <linux/soc/nxp/lpc32xx-misc.h>
|
#include <linux/stmmac.h>
|
#include <linux/sunrpc/svc_rdma.h>
|
#include <linux/sxgbe_platform.h>
|
#include <net/cfg80211.h>
|
#include <net/dsa.h>
|
#include <net/mac80211.h>
|
#include <net/selftests.h>
|
#include <rdma/ib_addr.h>
|
#include <rdma/ib_cache.h>
|
#include <rdma/ib_cm.h>
|
#include <rdma/ib_hdrs.h>
|
#include <rdma/ib_mad.h>
|
#include <rdma/ib_marshall.h>
|
#include <rdma/ib_pack.h>
|
#include <rdma/ib_pma.h>
|
#include <rdma/ib_sa.h>
|
#include <rdma/ib_smi.h>
|
#include <rdma/ib_umem.h>
|
#include <rdma/ib_umem_odp.h>
|
#include <rdma/ib_verbs.h>
|
#include <rdma/iw_cm.h>
|
#include <rdma/mr_pool.h>
|
#include <rdma/opa_addr.h>
|
#include <rdma/opa_port_info.h>
|
#include <rdma/opa_smi.h>
|
#include <rdma/opa_vnic.h>
|
#include <rdma/rdma_cm.h>
|
#include <rdma/rdma_cm_ib.h>
|
#include <rdma/rdmavt_cq.h>
|
#include <rdma/rdma_vt.h>
|
#include <rdma/rdmavt_qp.h>
|
#include <rdma/rw.h>
|
#include <rdma/tid_rdma_defs.h>
|
#include <rdma/uverbs_ioctl.h>
|
#include <rdma/uverbs_named_ioctl.h>
|
#include <rdma/uverbs_std_types.h>
|
#include <rdma/uverbs_types.h>
|
#include <soc/mscc/ocelot.h>
|
#include <soc/mscc/ocelot_ptp.h>
|
#include <soc/mscc/ocelot_vcap.h>
|
#include <trace/events/ib_mad.h>
|
#include <trace/events/rdma_core.h>
|
#include <trace/events/rdma.h>
|
#include <trace/events/rpcrdma.h>
|
#include <uapi/linux/ethtool.h>
|
#include <uapi/linux/ethtool_netlink.h>
|
#include <uapi/linux/mdio.h>
|
#include <uapi/linux/mii.h>
)

@depends on i@
expression list args;
@@

(
- bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_zero(args)
|
- bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_copy(args)
|
- bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_and(args)
|
- bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_or(args)
|
- bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_empty(args)
|
- bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_andnot(args)
|
- bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_equal(args)
|
- bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_intersects(args)
|
- bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_subset(args)
)

Add missing linux/mii.h include to mellanox. -DaveM

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: be compatible with masters which unregister on shutdown

Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.

What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.

This message can be seen in a loop, and it hangs the reboot process there:

unregister_netdevice: waiting for eth0 to become free. Usage count = 3

So why 3?

A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:

dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold

So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.

Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.

It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.

So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.

However, complications arise really quickly.

The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).

Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.

So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.

So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.

The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.

The answer to that question lies in this comment above device_link_add:

* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).

so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.

Fixes: 2f1e8ea726e9 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca: ar9331: make proper initial port defaults

Make sure that all external port are actually isolated from each other,
so no packets are leaked.

Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca: ar9331: reorder MDIO write sequence

In case of this switch we work with 32bit registers on top of 16bit
bus. Some registers (for example access to forwarding database) have
trigger bit on the first 16bit half of request and the result +
configuration of request in the second half. Without this patch, we would
trigger database operation and overwrite result in one run.

To make it work properly, we should do the second part of transfer
before the first one is done.

So far, this rule seems to work for all registers on this switch.

Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210803063746.3600-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: set configure_vlan_while_not_filtering to true by default

As explained in commit 54a0ed0df496 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.

New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.

Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.

The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.

The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.

Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.

No behavior change except for the added prints is intended at this time.

$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: qca: ar9331: export stats64

Add stats support for the ar9331 switch.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa: qca: ar9331: fix sleeping function called from invalid context bug

With lockdep enabled, we will get following warning:

ar9331_switch ethernet.1:10 lan0 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:00] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13)
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 18, name: kworker/0:1
INFO: lockdep is turned off.
irq event stamp: 602
hardirqs last enabled at (601): [<8073fde0>] _raw_spin_unlock_irq+0x3c/0x80
hardirqs last disabled at (602): [<8073a4f4>] __schedule+0x184/0x800
softirqs last enabled at (0): [<80080f60>] copy_process+0x578/0x14c8
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 5.10.0-rc3-ar9331-00734-g7d644991df0c #31
Workqueue: events deferred_probe_work_func
Stack : 80980000 80980000 8089ef70 80890000 804b5414 80980000 00000002 80b53728
00000000 800d1268 804b5414 ffffffde 00000017 800afe08 81943860 0f5bfc32
00000000 00000000 8089ef70 819436c0 ffffffea 00000000 00000000 00000000
8194390c 808e353c 0000000f 66657272 80980000 00000000 00000000 80890000
804b5414 80980000 00000002 80b53728 00000000 00000000 00000000 80d40000
...
Call Trace:
[<80069ce0>] show_stack+0x9c/0x140
[<800afe08>] ___might_sleep+0x220/0x244
[<8073bfb0>] __mutex_lock+0x70/0x374
[<8073c2e0>] mutex_lock_nested+0x2c/0x38
[<804b5414>] regmap_update_bits_base+0x38/0x8c
[<804ee584>] regmap_update_bits+0x1c/0x28
[<804ee714>] ar9331_sw_unmask_irq+0x34/0x60
[<800d91f0>] unmask_irq+0x48/0x70
[<800d93d4>] irq_startup+0x114/0x11c
[<800d65b4>] __setup_irq+0x4f4/0x6d0
[<800d68a0>] request_threaded_irq+0x110/0x190
[<804e3ef0>] phy_request_interrupt+0x4c/0xe4
[<804df508>] phylink_bringup_phy+0x2c0/0x37c
[<804df7bc>] phylink_of_phy_connect+0x118/0x130
[<806c1a64>] dsa_slave_create+0x3d0/0x578
[<806bc4ec>] dsa_register_switch+0x934/0xa20
[<804eef98>] ar9331_sw_probe+0x34c/0x364
[<804eb48c>] mdio_probe+0x44/0x70
[<8049e3b4>] really_probe+0x30c/0x4f4
[<8049ea10>] driver_probe_device+0x264/0x26c
[<8049bc10>] bus_for_each_drv+0xb4/0xd8
[<8049e684>] __device_attach+0xe8/0x18c
[<8049ce58>] bus_probe_device+0x48/0xc4
[<8049db70>] deferred_probe_work_func+0xdc/0xf8
[<8009ff64>] process_one_work+0x2e4/0x4a0
[<800a0770>] worker_thread+0x2a8/0x354
[<800a774c>] kthread+0x16c/0x174
[<8006306c>] ret_from_kernel_thread+0x14/0x1c

ar9331_switch ethernet.1:10 lan1 (uninitialized): PHY [!ahb!ethernet@1a000000!mdio!switch@10:02] driver [Qualcomm Atheros AR9331 built-in PHY] (irq=13)
DSA: tree 0 setup

To fix it, it is better to move access to MDIO register to the .irq_bus_sync_unlock
call back.

Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201211110317.17061-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: dsa/ar9331: convert to mac_link_up()

Convert the ar9331 DSA driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().

Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: propagate resolved link config via mac_link_up()

Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.

Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Get information about stacked DSA protocol

It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.

This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.

The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: qca: ar9331: drop pointless static qualifier in ar9331_sw_mbus_init

There is no need to set variable 'mbus' static
since new value always be assigned before use it.

Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: add support for Atheros AR9331 built-in switch

Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>