media: v4l2-subdev: Rename .init_cfg() operation to .init_state()

The subdev .init_cfg() operation is affected by two issues:

- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.

- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.

This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: v4l2-fwnode: Move bus config structure to v4l2_mediabus.h

To prepare for usage of the v4l2_fwnode_bus_* data structures to
describe bus configuration in the subdev .get_mbus_config() operation,
rename the structures with a v4l2_mbus_config_ prefix instead of
v4l2_fwnode_bus_, and move them to v4l2_mediabus.h.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-async: Clean v4l2_async_notifier_add_fwnode_remote_subdev

Change v4l2_async_notifier_add_fwnode_remote_subdev semantics
so it allocates the struct v4l2_async_subdev pointer.

This makes the API consistent: the v4l2-async subdevice addition
functions have now a unified usage model. This model is simpler,
as it makes v4l2-async responsible for the allocation and release
of the subdevice descriptor, and no longer something the driver
has to worry about.

On the user side, the change makes the API simpler for the drivers
to use and less error-prone.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: sun4i-csi: Add support for A10 CSI1 camera sensor interface

The A10/A20 Allwinner SoCs have two camera sensor interface blocks,
named CSI0 and CSI1. The two have the same register layouts with
slightly different features:

- CSI0 has an image signal processor (ISP); CSI1 doesn't

- CSI0 can support up to four separate channels under CCIR656;
CSI1 can only support one

- CSI0 can support up to 16-bit wide bus with YUV422;
CSI1 can support up to 24-bit wide bus with YUV444

For now the driver doesn't support wide busses, nor CCIR656. So the
only relevant difference is whether a clock needs to be taken and
enabled for the ISP.

Add structs to record the differences, tie them to the compatible
strings, and deal with the ISP clock. Support for the new CSI1
hardware block is added as well.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: sun4i-csi: Fix [HV]sync polarity handling

The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.

Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.

Fixes: 577bbf23b758 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: sunxi: Add A10 CSI driver

The older CSI drivers have camera capture interface different from the one
in the newer ones.

This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.

[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>