media: i2c: replace of_graph_get_next_endpoint()

From DT point of view, in general, drivers should be asking for a
specific port number because their function is fixed in the binding.

of_graph_get_next_endpoint() doesn't match to this concept.

Simply replace

- of_graph_get_next_endpoint(xxx, NULL);
+ of_graph_get_endpoint_by_regs(xxx, 0, -1);

Link: https://lore.kernel.org/r/20240202174941.GA310089-robh@kernel.org
Link: https://lore.kernel.org/r/9d1e99b0-892d-4a72-a9b3-886b8ed094b0@xs4all.nl
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: i2c: ov5645: Remove software reset entry from ov5645_global_init_setting

The SYSTEM_CTRL0 register in ov5645 is almost similar to ov5640. But the
hard reset control is mandatory for the ov5645 device, so there is no
need for soft reset in the driver.

Add a 1msec delay for the software power up (OV5645_SYSTEM_CTRL0_START)
register in ov5645_global_init_setting. Without this delay sometimes the
image is not captured at all when the i2c frequency is 400kHz.

The changes are fixing both the greenish issue and image capture at 400kHz
i2c frequency on Renesas RZ/G2L SMARC EVK platforms.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: v4l2-subdev: Rename .init_cfg() operation to .init_state()

The subdev .init_cfg() operation is affected by two issues:

- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.

- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.

This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: v4l: subdev: Switch to stream-aware state functions

Switch all drivers accessing sub-device state to use the stream-aware
functions. We will soon remove the old ones.

This patch has been generated using the following Coccinelle script:

---------8<------------
@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_pad_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)

@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_pad_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)

@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_pad_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)

@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_try_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)

@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_try_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)

@@
expression E1, E2, E3;

@@

- v4l2_subdev_get_try_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
---------8<------------

Additionally drivers/media/i2c/s5k5baf.c and
drivers/media/platform/samsung/s3c-camif/camif-capture.c have been
manually changed as Coccinelle didn't. Further local variables have been
removed as they became unused as a result of the other changes.

Also Coccinelle introduced indentation by space in files
drivers/media/i2c/st-mipid02.c and
drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also
corrected.

The diff from Coccinelle-generated changes are:

> diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c
> index e549692ff478..420984382173 100644
> --- b/drivers/media/i2c/imx319.c
> +++ a/drivers/media/i2c/imx319.c
> @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx319->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c
> index 96bdde685d65..e1b1d2fc79dd 100644
> --- b/drivers/media/i2c/imx355.c
> +++ a/drivers/media/i2c/imx355.c
> @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx355->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c
> index ca799bbcfdb7..abbb0b774d43 100644
> --- b/drivers/media/i2c/ov08x40.c
> +++ a/drivers/media/i2c/ov08x40.c
> @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov08x->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c
> index 7816d9787c61..09387e335d80 100644
> --- b/drivers/media/i2c/ov13858.c
> +++ a/drivers/media/i2c/ov13858.c
> @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13858->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c
> index 268cd4b03f9c..c06411d5ee2b 100644
> --- b/drivers/media/i2c/ov13b10.c
> +++ a/drivers/media/i2c/ov13b10.c
> @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13b->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> index 47605e36bc60..8f9b5713daf7 100644
> --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state,
> struct v4l2_subdev_format *fmt,
> const struct s5c73m3_frame_size **fs)
> {
> - struct v4l2_subdev *sd = &state->sensor_sd;
> u32 code;
>
> switch (fmt->pad) {
> diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c
> index 67da2045f543..03ccfb0e1e11 100644
> --- a/drivers/media/i2c/s5k5baf.c
> +++ b/drivers/media/i2c/s5k5baf.c
> @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
>
> if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> rects = (struct v4l2_rect * []) {
> - &s5k5baf_cis_rect,
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_compose(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_OUT)
> - };
> + &s5k5baf_cis_rect,
> + v4l2_subdev_state_get_crop(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_compose(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_crop(sd_state, PAD_OUT)
> + };
> s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
> return 0;
> }
> diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> index 295e083f38e8..be58260ea67e 100644
> --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
> struct v4l2_mbus_framefmt *mf = &fmt->format;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> fmt->format = *mf;
> return 0;
> }
> @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
> __camif_subdev_try_format(camif, mf, fmt->pad);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> *mf = fmt->format;
> mutex_unlock(&camif->lock);
> return 0;
> diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c
> index cea454ed9c20..61433744c6c4 100644
> --- b/drivers/media/platform/ti/cal/cal-camerarx.c
> +++ a/drivers/media/platform/ti/cal/cal-camerarx.c
> @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - struct cal_camerarx *phy = to_cal_camerarx(sd);
> -
> /* No transcoding, source and sink codes must match. */
> if (cal_rx_pad_is_source(code->pad)) {
> struct v4l2_mbus_framefmt *fmt;
> diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c
> index dd558fac6477..61d69f19657e 100644
> --- b/drivers/staging/media/imx/imx-ic-prp.c
> +++ a/drivers/staging/media/imx/imx-ic-prp.c
> @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c
> index 02db7dbb884b..ec73c901079e 100644
> --- b/drivers/staging/media/imx/imx-ic-prpencvf.c
> +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c
> @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
> index 9c9361354c00..b08a249b5fdd 100644
> --- a/drivers/media/i2c/st-mipid02.c
> +++ b/drivers/media/i2c/st-mipid02.c
> @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
> format->format = bridge->fmt;
> else
> format->format = *v4l2_subdev_state_get_format(sd_state,
> - MIPID02_SINK_0);
> + MIPID02_SINK_0);
>
> /* but code may need to be converted */
> format->format.code = serial_to_parallel_code(format->format.code);
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 117912d3bfbd..96353648c032 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp,
> rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val);
>
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_info = rkisp1_mbus_info_get_by_code(src_fmt->code);
>
> if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER)
> @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp,
> sink_fmt = v4l2_subdev_state_get_format(sd_state,
> RKISP1_ISP_PAD_SINK_VIDEO);
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_crop = v4l2_subdev_state_get_crop(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
>
> /*
> * Media bus code. The ISP can operate in pass-through mode (Bayer in,

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

media: i2c: ov5645: Call ov5645_entity_init_cfg() before registering the subdev

Make sure we call ov5645_entity_init_cfg() before registering the subdev
to make sure default formats are set up.

Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Make sure to call PM functions

Make sure we call the PM functions while s_stream(0) even in case of
errors in the code flow.

v4l2-core takes care of warning the user so no need to add a warning
message in the driver.

Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Drop empty comment

Drop empty multiline comment.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Use runtime PM

Switch to using runtime PM for power management.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Drop fetching the clk reference by name

The OV5645 sensor has a single clock source, so just drop fetching the
clk reference by name.

This is in preparation to drop the "clock-names" property from the DT
binding.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

media: i2c: ov5645: Remove unneeded of_match_ptr macro

of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig

Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Fix media bus format

The ov5645 driver reports as its unique supported format
MEDIA_BUS_FMT_UYVY8_2X8, which is not correct as the sensor
uses the MIPI CSI-2 serial bus.

Fix that by using MEDIA_BUS_FMT_UYVY8_1X16 instead.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-subdev: add subdev-wide state struct

We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.

I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.

This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.

The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:

dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done

Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:

For drivers/media/i2c/s5k5baf.c:

@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;

For drivers/media/platform/s3c-camif/camif-capture.c:

@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;

- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;

- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;

The semantic patch is:

// <smpl>

// Change function parameter

@@
identifier func;
identifier cfg;
@@

func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}

// Change function declaration parameter

@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);

// Change function return value

@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}

// Change function declaration return value

@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);

// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.

@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };

<+...

(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)

...+>
}

// If the function uses fields from pad_config, access via state->pads

@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}

// If the function accesses the filehandle, use fh->state instead

@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state

@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state

// Start of vsp1 specific

@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};

@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}

@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}

@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}

// End of vsp1 specific

// Start of rcar specific

@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}

// End of rcar specific

// Start of rockchip specific

@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@

func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}

@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@

func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}

@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@

rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}

// End of rockchip specific

// Start of tegra-video specific

@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}

@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}

// End of tegra-video specific

// </smpl>

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov5645: Fix power sequence

This is mostly a port of Jacopo's fix:

commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <jacopo@jmondi.org>
Date: Fri Jul 6 05:51:52 2018 -0400

media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.

Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: Convert to new i2c device probe()

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type").

These drivers do not utilise the i2c_device_id table in the probe, so we
can easily convert them to utilise the simplified i2c driver
registration.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Use regulator_bulk() functions

The code can be simplified by using the regulator_bulk() functions,
so switch to it.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Remove unneeded regulator_set_voltage()

There is no need to call regulator_set_voltage() for each regulator
that powers the camera.

The voltage value for each regulator should be retrieved from the
device tree, so remove the unneeded regulator_set_voltage().

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

Based on 3 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: ov5645: constify v4l2_ctrl_ops structure

The v4l2_ctrl_ops structure is only passed as the second argument to
functions such as v4l2_ctrl_new_std for which the corresponding
parameter is const, so make the v4l2_ctrl_ops structure const as well.

Done with the help of Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: mediabus: Recognise CSI-2 D-PHY and C-PHY

The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Supported external clock is 24MHz

The external clock frequency was set to 23.88MHz by mistake
because of a platform which cannot get closer to 24MHz.
The supported by the driver external clock is 24MHz so
set it correctly and also fix the values of the pixel
clock and link clock.
However allow 1% tolerance to the external clock as this
difference is small enough to be insignificant.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Fix write_reg return code

I2C transfer functions return number of successful operations (on success).

Do not return the received positive return code but instead return 0 on
success. The users of write_reg function already use this logic.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Use v4l2_find_nearest_size

Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: ov5645: add missing of_node_put() in error path

The device node obtained with of_graph_get_next_endpoint() should be
released by calling of_node_put(). But it was not released when
v4l2_fwnode_endpoint_parse() failed.

This change moves the of_node_put() call before the error check and
fixes the issue.

Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: ov5645: Add control to export CSI2 link frequency

Add suport for standard integer menu V4L2_CID_LINK_FREQ control.
The CSI2 link frequency value is specific for each sensor mode so the
sensor mode structure is extended to add this. The control is made
read-only and its value is updated when the sensor mode is changed -
on set_format.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: ov5645: Add control to export pixel clock frequency

Add suport for standard V4L2_CID_PIXEL_RATE control. The pixel clock
frequency value is specific for each sensor mode so the sensor mode
structure is extended to add this. The control is read-only and its
value is updated when the sensor mode is changed - on set_format.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

media: ov5645: Set media entity function

Set media entity function to MEDIA_ENT_F_CAM_SENSOR.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] v4l: Switch from V4L2 OF not V4L2 fwnode API

Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

[media] media: Add a driver for the ov5645 camera sensor

The ov5645 sensor from Omnivision supports up to 2592x1944
and CSI2 interface.

The driver adds support for the following modes:
- 1280x960
- 1920x1080
- 2592x1944

Output format is packed 8bit UYVY.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>