RDMA/core: Use refcount_t instead of atomic_t on refcount of mcast_port

The refcount_t API will WARN on underflow and overflow of a reference
counter, and avoid use-after-free risks.

Link: https://lore.kernel.org/r/1622194663-2383-6-git-send-email-liweihang@huawei.com
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

RDMA/core: Use refcount_t instead of atomic_t on refcount of mcast_member

The refcount_t API will WARN on underflow and overflow of a reference
counter, and avoid use-after-free risks.

Link: https://lore.kernel.org/r/1622194663-2383-5-git-send-email-liweihang@huawei.com
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

RDMA: Support more than 255 rdma ports

Current code uses many different types when dealing with a port of a RDMA
device: u8, unsigned int and u32. Switch to u32 to clean up the logic.

This allows us to make (at least) the core view consistent and use the
same type. Unfortunately not all places can be converted. Many uverbs
functions expect port to be u8 so keep those places in order not to break
UAPIs. HW/Spec defined values must also not be changed.

With the switch to u32 we now can support devices with more than 255
ports. U32_MAX is reserved to make control logic a bit easier to deal
with. As a device with U32_MAX ports probably isn't going to happen any
time soon this seems like a non issue.

When a device with more than 255 ports is created uverbs will report the
RDMA device as having 255 ports as this is the max currently supported.

The verbs interface is not changed yet because the IBTA spec limits the
port size in too many places to be u8 and all applications that relies in
verbs won't be able to cope with this change. At this stage, we are
extending the interfaces that are using vendor channel solely

Once the limitation is lifted mlx5 in switchdev mode will be able to have
thousands of SFs created by the device. As the only instance of an RDMA
device that reports more than 255 ports will be a representor device and
it exposes itself as a RAW Ethernet only device CM/MAD/IPoIB and other
ULPs aren't effected by this change and their sysfs/interfaces that are
exposes to userspace can remain unchanged.

While here cleanup some alignment issues and remove unneeded sanity
checks (mainly in rdmavt),

Link: https://lore.kernel.org/r/20210301070420.439400-1-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

RDMA/core/multicast: Provide description for 'ib_init_ah_from_mcmember()'s 'rec' param

Fixes the following W=1 kernel build warning(s):

drivers/infiniband/core/multicast.c:739: warning: Function parameter or member 'rec' not described in 'ib_init_ah_from_mcmember'

Link: https://lore.kernel.org/r/20210118223929.512175-12-lee.jones@linaro.org
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

RDMA: Allow ib_client's to fail when add() is called

When a client is added it isn't allowed to fail, but all the client's have
various failure paths within their add routines.

This creates the very fringe condition where the client was added, failed
during add and didn't set the client_data. The core code will then still
call other client_data centric ops like remove(), rename(), get_nl_info(),
and get_net_dev_by_params() with NULL client_data - which is confusing and
unexpected.

If the add() callback fails, then do not call any more client ops for the
device, even remove.

Remove all the now redundant checks for NULL client_data in ops callbacks.

Update all the add() callbacks to return error codes
appropriately. EOPNOTSUPP is used for cases where the ULP does not support
the ib_device - eg because it only works with IB.

Link: https://lore.kernel.org/r/20200421172440.387069-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

RDMA: Replace zero-length array with flexible-array member

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
int stuff;
struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")

Link: https://lore.kernel.org/r/20200213010425.GA13068@embeddedor.com
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> # added a few more

IB/core, ipoib: Do not overreact to SM LID change event

When IPoIB receives an SM LID change event, it reacts by flushing its
path record cache and rejoining multicast groups. This is the same
behavior it performs when it receives a reregistration event. This
behavior is unnecessary as an SM may have database backup or
synchronization mechanisms which permit the SM location or LID to change
without loss of multicast membership and without impact to path records.

Both opensm and the OPA FM issue reregistration events if a new SM is
started (or restarted with a new config) or an SM event occurs which
results in loss of multicast membership records by the SM (such as
opensm failover) or the SM encounters new nodes with Active ports (such
as after joining 2 fabrics by connecting switches via ISLs). Hence this
event can be depended on as the trigger for IPoIB cache and multicast
flushing.

It appears that some drivers, such as qib, and hfi1 issue the
IB_EVENT_SM_CHANGE but other drivers such as mlx4 and mlx5 do not.
Empirical testing on Mellanox EDR using ibv_asyncwatch has confirmed
that Mellanox EDR HCAs do not generate SM change events and that opensm
does generate reregistration.

An SM LID change event is generated by the mentioned drivers to reflect
that sm_lid and/or sm_sl in the local port info has changed. The intent
of this event is to permit applications and ULPs which have a local copy
of this information (or an address handle using it) to update their
information.

The intent is that the reregistration event (caused by the SM via a bit
in Set(PortInfo)) be used to inform nodes that they need to rejoin
multicast groups, resubscribe for notices and potentially update path
records.

When an SM migrates or fails over, a SM LID change event can occur. In
response IPoIB discards path records and multicast membership and loses
connectivity until these records are restored via SA requests. In very
large fabrics, it may take minutes for the SM to be ready and for the SA
responses to be supplied. This can result in undesirable and
unnecessary IPoIB connectivity impacts. It also can result in an
unnecessary storm of SA queries from all nodes in a cluster potentially
followed by yet another storm if the SM issues the reregistration
request.

The fact the Mellanox HCAs do not even generate this event, is further
evidence that on modern IB fabrics there will be no ill side effects
from the proposed changes below to reduce the reaction by 3 kernel
components to this event. So these changes should be benign for Mellanox
IB fabrics and will benefit OPA fabrics while also making ib_core and
ULP behavor "correct" as intended by the IBTA spec and kernel RDMA event
APIs.

Address these issues by removing IB_EVENT_SM_CHANGE handling from ipoib.
IPoIB does not locally store sm_lid nor sm_sl, so it does not need to do
anything on SM LID change. IPoIB makes use of other ib_core components
to issue SA requests for it and those components correctly track SM LID
and SM LID changes.

Also in ib_core multicast handling, remove the test for
IB_EVENT_SM_CHANGE. This code is moving all multicast groups to the
error state, which will trigger rejoins. This code is used by IPoIB as
well as the connection manager and other clients of multicast groups.
This kernel module centralizes group membership status and joins since a
node can only join a given group once but multiple ULPs or applications
may want to join the same group. It makes use of the sa_query.c
component in ib_core, which correctly trackes SM LID and SL. This
component does not track SM LID nor SL itself and hence need not react
to their changes.

Similarly in the ib_core cache code remove the handling for the
IB_EVENT_SM_CHANGE. In this function. The ib_cache_update function
which is ultimately called is updating local copies of the pkey table,
gid table and lmc. It does not update nor retain sm_lid nor sm_sl. As
such it does not need to be called on an SM LID change. It technically
also does not need to be called on a reregistration. The LID_CHANGE,
PKEY_CHANGE, GID_CHANGE and port state change events (PORT_ERR,
PORT_ACTICE) should be sufficient triggers.

It is worth noting that the alternative of simply having the hfi1 and
qib drivers not generate the SM LID change event was explored. While
this would duplicate what Mellanox drivers do now, it is not the correct
behavior and removes the ability for an SM to migrate without requiring
reregistration. Since both opensm and OPA SM have mechanisms to backup
or synchronize registration information, it is desirable to let them
perform SM migrations (with LID or SL changes) without requiring
reregistration when they deem it appropriate.

Suggested-by: Todd Rimmer <todd.rimmer@intel.com>
Tested-by: Michael Brooks <michael.brooks@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Todd Rimmer <todd.rimmer@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

IB: Make ib_init_ah_from_mcmember set sgid_attr

This is really just a CM support function, normally a multicast address
does not have a specific SGID - but the RDMA CM usage model does restrict
things to the netdevice the CM id is bound to, at least for roce case.

Store the selected table entry in the sgid_attr for everything else to
use.

Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

treewide: Use struct_size() for kmalloc()-family

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
int stuff;
void *entry[];
};

instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);

This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:

// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)

// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)

// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@

- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)

Signed-off-by: Kees Cook <keescook@chromium.org>

IB/core: Honor port_num while resolving GID for IB link layer

ah_attr contains the port number to which cm_id is bound. However, while
searching for GID table for matching GID entry, the port number is
ignored.

This could cause the wrong GID to be used when the ah_attr is converted to
an AH.

Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

IB/core: Define 'ib' and 'roce' rdma_ah_attr types

rdma_ah_attr can now be either ib or roce allowing
core components to use one type or the other and also
to define attributes unique to a specific type. struct
ib_ah is also initialized with the type when its first
created. This ensures that calls such as modify_ah
dont modify the type of the address handle attribute.

Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Use rdma_ah_attr accessor functions

Modify core and driver components to use accessor functions
introduced to access individual fields of rdma_ah_attr

Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Rename struct ib_ah_attr to rdma_ah_attr

This patch simply renames struct ib_ah_attr to
rdma_ah_attr as these fields specify attributes that are
not necessarily specific to IB.

Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/multicast: Check ib_find_pkey() return value

This patch avoids that Coverity complains about not checking the
ib_find_pkey() return value.

Fixes: commit 547af76521b3 ("IB/multicast: Report errors on multicast groups if P_key changes")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/multicast: Remove deprecated create_singlethread_workqueue

alloc_ordered_workqueue() with WQ_MEM_RECLAIM set, replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.

The workqueue "mcast_wq" queues work item &group->work. It has been
identity converted.

WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.

Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Fix use after free in send_leave function

The function send_leave sets the member: group->query_id
(group->query_id = ret) after calling the sa_query, but leave_handler
can be executed before the setting and it might delete the group object,
and will get a memory corruption.

Additionally, this patch gets rid of group->query_id variable which is
not used.

Fixes: faec2f7b96b5 ('IB/sa: Track multicast join/leave requests')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Support for CMA multicast join flags

Added UCMA and CMA support for multicast join flags. Flags are
passed using UCMA CM join command previously reserved fields.
Currently supporting two join flags indicating two different
multicast JoinStates:

1. Full Member:
The initiator creates the Multicast group(MCG) if it wasn't
previously created, can send Multicast messages to the group
and receive messages from the MCG.

2. Send Only Full Member:
The initiator creates the Multicast group(MCG) if it wasn't
previously created, can send Multicast messages to the group
but doesn't receive any messages from the MCG.

IB: Send Only Full Member requires a query of ClassPortInfo
to determine if SM/SA supports this option. If SM/SA
doesn't support Send-Only there will be no join request
sent and an error will be returned.

ETH: When Send Only Full Member is requested no IGMP join
will be sent.

Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Support new type of join-state for multicast

There are four types for MCG, FullMember, NonMember, SendOnlyNonMember,
and the new added type: SendOnlyFullMember.
Add support for the new SendOnlyFullMember join state.

The new type allows host to send join request as sendonly, it will cause the
group to be created but without getting packets from this multicast back to the
host.

Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/cma: Join and leave multicast groups with IGMP

Since RoCEv2 is a protocol over IP header it is required to send IGMP
join and leave requests to the network when joining and leaving
multicast groups.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add gid_type to gid attribute

In order to support multiple GID types, we need to store the gid_type
with each GID. This is also aligned with the RoCE v2 annex "RoCEv2 PORT
GID table entries shall have a "GID type" attribute that denotes the L3
Address type". The currently supported GID is IB_GID_TYPE_IB which is
also RoCE v1 GID type.

This implies that gid_type should be added to roce_gid_table meta-data.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Add netdev and gid attributes paramteres to cache

Adding an ability to query the IB cache by a netdev and get the
attributes of a GID. These parameters are necessary in order to
successfully resolve the required GID (when the netdevice is known)
and get the Ethernet L2 attributes from a GID.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-By: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: lock client data with lists_rwsem

An ib_client callback that is called with the lists_rwsem locked only for
read is protected from changes to the IB client lists, but not from
ib_unregister_device() freeing its client data. This is because
ib_unregister_device() will remove the device from the device list with
lists_rwsem locked for write, but perform the rest of the cleanup,
including the call to remove() without that lock.

Mark client data that is undergoing de-registration with a new going_down
flag in the client data context. Lock the client data list with lists_rwsem
for write in addition to using the spinlock, so that functions calling the
callback would be able to lock only lists_rwsem for read and let callbacks
sleep.

Since ib_unregister_client() now marks the client data context, no need for
remove() to search the context again, so pass the client data directly to
remove() callbacks.

Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB: Add rdma_cap_ib_switch helper and use where appropriate

Persuant to Liran's comments on node_type on linux-rdma
mailing list:

In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".

In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).

The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.

Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Don't warn on no SA support in event handler

Registering an event handler is done for a device. This device may have
one RoCE port (no SA cap) and one InfiniBand port (has SA cap).
Therefore, warning from the event handler about a specific port that
doesn't have SA cap is correct but pollutes the kernel log without a
need.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/Verbs: Use management helper rdma_cap_ib_mcast()

Introduce helper rdma_cap_ib_mcast() to help us check if the port of an
IB device support Infiniband Multicast.

Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/Verbs: Reform IB-core multicast

Use raw management helpers to reform IB-core multicast.

Signed-off-by: Michael Wang <yun.wang@profitbricks.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

IB/core: Fix mgid key handling in SA agent multicast data-base

Applications can request that the SM assign an MGID by passing a mcast
member request containing MGID = 0. When the SM responds by sending
the allocated MGID, this MGID replaces the 0-MGID in the multicast group.

However, the MGID field in the group is also the key field in the IB
core multicast code rbtree containing the multicast groups for the
port.

Since this is a key field, correct handling requires that the group
entry be deleted from the rbtree and then re-inserted with the new
key, so that the table structure is properly maintained.

The current code does not do this correctly. Correct operation
requires that if the key-field gid has changed at all, it should be
deleted and re-inserted.

Note that when inserting, if the new MGID is zero (not the case here
but the code should handle this correctly), we allow duplicate entries
for 0-MGIDs.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

infiniband: add in export.h for files using EXPORT_SYMBOL/THIS_MODULE

These were getting it implicitly via device.h --> module.h but
we are going to stop that when we clean up the headers.

Fix these in advance so the tree remains biscect-clean.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

IB/mad: IBoE supports only QP1 (no QP0)

Since IBoE is using Ethernet as its link layer, there is no central
management entity so there is need for QP0. QP1 is still needed since
it handles communications between CM agents. This patch will skip QP0
and create only QP1 for IBoE ports.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.

2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).

* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

IB/core: Fix send multicast group leave retry

Until now, retries were only sent when joining a multicast group. This
patch will adds retries when leaving a multicast group as well.

Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/multicast: Report errors on multicast groups if P_key changes

P_key changes can invalidate multicast groups. Report errors on all
multicast groups affected by a pkey change.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/core: Fix handling of multicast response failures

I was looking at the code for multicast.c and noticed that
ib_sa_join_multicast() calls queue_join() which puts the
request at the front of the group->pending_list. If this
is a second request, it seems like it would interfere with
process_join_error() since group->last_join won't point
to the member at the head of the pending_list. The sequence
would thus be:

1. ib_sa_join_multicast()
puts member1 on head of pending_list and starts work thread
2. mcast_work_handler()
calls send_join() which sets group->last_join to member1
3. ib_sa_join_multicast()
puts member2 on head of pending_list
4. join operation for member1 receives failures response from SA.
5. join_handler() is called with error status
6. process_join_error() fails to process member1 since
it doesn't match the first entry in the group->pending_list.

The impact is that the failed join request is tossed. The second
request is processed, and after it completes, the original request ends
up being retried.

This change also results in join requests being processed in FIFO
order.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB: Remove garbage non-ASCII characters from comments

A few files had 0xa0 characters in comments. Remove them so that the
files are clean ASCII text.

Signed-off-by: Roland Dreier <rolandd@cisco.com>

PCI: Cleanup the includes of <linux/pci.h>

I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.

In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.

My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:

arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c

I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.

Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

IB/sa: Track multicast join/leave requests

The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.

To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.

Signed-off-by: Roland Dreier <rolandd@cisco.com>