drm/amd/display: Amend coasting vtotal for replay low hz

[WHY]
The original coasting vtotal is 2 bytes, and it need to
be amended to 4 bytes because low hz case.

[HOW]
Amend coasting vtotal from 2 bytes to 4 bytes.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add shared firmware state for DMUB IPS handshake

[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.

[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.

Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.

Remove the workarounds that required rewriting/checking read modify
write hazards.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Drop legacy code

Display code keeps getting improvements, and because of that, some
legacy code is left behind. This commit drops some of those unused
codes.

Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.202.0

- Add control flag for IPS residency profiling

Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: refine code for dmcub inbox1 ring buffer debug

[Why]
1. To watch dmcub inbox1 ring buffer cmd type without tools
2. dmub_cmd_PLAT_54186_wa 66 bytes

[How]
Added dmcub cmd type enum: unsigned char for debug use only,
also fixed 66 bytes issue by using unsigned int in bit
define instead of unsigned char.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.201.0

- Add debug flag for Replay IPS visual confirm
- Remove unused debug flags that should not
be controlled inside Replay FSM

Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Replay + IPS + ABM in Full Screen VPB

[Why]
Because ABM will wait VStart to start getting histogram data,
it will cause we can't enter IPS while full screnn video playing.

[How]
Modify the panel refresh rate to the maximun multiple of current
refresh rate.

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Replay IPS register for DMUB command table

- Introduce a new Replay mode for DMUB version 0.0.199.0

Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Replay + IPS + ABM in Full Screen VPB

[Why]
Because ABM will wait VStart to start getting histogram data,
it will cause we can't enter IPS while full screnn video playing.

[How]
Modify the panel refresh rate to the maximun multiple of current
refresh rate.

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Replay IPS register for DMUB command table

- Introduce a new Replay mode for DMUB version 0.0.199.0

Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.197.0

- Remove unused dmub_fw_boot_options flag

Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Pass pwrseq inst for backlight and ABM

[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.

[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.194.0

- Add a new dmub command in enum dmub_cmd_cab_type

Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.193.0

- Add a tracing framework, to measure duration, execution count and
longest duration of main loop/vsync interrupt work
GPINT command is used to start/stop the measurements.

Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Disable Timing sync check in Full-Screen Video Case

[why]
If Panel max link off frame count is low, it will cause low residency
for Replay, then Disabled timing sync check in Full screen Video Case.

Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: replay: Augment Frameupdate Command

[Why]
Sending certain Frameupdate number for Replay Power Evaluation

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: replay: generalize the send command function usage

Augment the function to allow send different format data in different
use case.

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add new command to disable replay timing resync

[WHY & HOW]
Add new command to disable replay timing resync

Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add a debugfs interface for the DMUB trace mask

For features that are implemented primarily in DMUB (e.g. PSR), it is
useful to be able to trace them at a DMUB level from the kernel,
especially when debugging issues. So, introduce a debugfs interface that
is able to read and set the DMUB trace mask dynamically at runtime and
document how to use it.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.190.0

- Increase number of bits for IPS boot option

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable more IPS options

[why]
To help isolate static screen and
video playback tests, we want to enable
an IPS option to allow IPS only on D3 cycle.

[how]
Add DISABLE_DYNAMIC and DISABLE_ALL
IPS disable flags for user control.

Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.189.0

- Minor formatting changes
- Update defines to match the bit width of the field it is used for
- Add new boot up bits to control HW sub block regions power
down

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor HWSS into component folder

[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.

[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.

Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Adjust code style for dmub_cmd.h

[Why&How]
Make some formatting changes and rearranging of definitions for consistency.

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update DMUB cmd header

[Why&How]
* Add hints about the bits used in the packed struct.
* Update new bitfields for ABM and IPS

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.183.0

- Add new IPS ALLOW masks
- Add new Replay power configuration options

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: support main link off before specific vertical line

[Why]
Some panels request main link off before specific vertical line.
If source turn off main link after specific vertical line then
panel defect will be exposed.

[How]
Add interface to support turn off main link before specific
vertical line

Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.181.0

- Add new params to dmub_feature_caps for checking replay
support in FW

Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.180.0

- Remove unused flag otg_powered_down

Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.179.0

- Add defines to specify new PHY power states

Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add interface to enable DPIA trace

[Why]
DPIA traces from DMUB is not enabled by default, which is
less convenient to debug DPIA related issues because we have
to resort to other debug tools to enable DPIA trace.

[How]
Exposes interfaces to update trace mask from the DMUB GPINT commands.
Also provides DC implementations to enable DPIA trace.

Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add structs for Freesync Panel Replay

In some instances, the GPU is transmitting repeated frame to the sink
without any updates or changes in the content. These repeat transmission
are wasteful, resulting in power draw in different aspects of the system

1. DCN is fetching the frame of data from DF/UMC/DRAM. This memory traffic
prevents power down of parts of this HW path.

2. GPU is transmitting pixel data to the display through the main link of
the DisplayPort interface. This prevents power down of both the Source
transmitter (TX) and the Sink receiver (RX)

The concepts of utilizing replay is similar to PSR, but there is a benefit of:
Source and Sink remaining synchronized which allows for
- lower latency when switching from replay to live frames
- enable the possibility of more use cases
- easy control of the sink's refresh rate during replay

Due to Source and Sink remaining timing synchronized, Replay can be activated
in more UI scenarios.

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Rearrange dmub_cmd defs order

- Rearranged defs order

Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Correct grammar mistakes

[Why]
There are grammer mistakes in comments

[How]
Correct grammar mistakes

Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: ABM pause toggle

[why]
Allow ABM states to be transferred across display
adapters for smooth display transitions.

[how]
We call DMUB to pause and get ABM states. We
transfer data to other gpu, and deliver data and
ask ABM to un-pause.

Reviewed-by: Harry Vanzylldejong <harry.vanzylldejong@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.165.0

- Add dmub boot options to disable ips states on init

Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update FW feature caps struct

Reorder FW feature caps struct variable order to ensure backwards
compatability is maintained for older FW

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.163.0

Add feature caps for Subvp + PSR so driver is back compatible

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add FAMS related definitions and documenation for enum fields

[Why&How]
Add Enum and documenation related to FAMS (Firmware Assisted Memclk
Switching) and CAB (Cache As Buffer)

Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.162.0

- Add DMUB_CMD__IDLE_OPT_DCN_NOTIFY_IDLE command
- Remove d3 entry event and instead check for stream mask
- dmu: Enable timeout recovery and detection for p-state

Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add FAMS validation before trying to use it

To ensure that FAMS can be used, DC must check if there is VRR support.
This commit adds the required configuration to ensure FAMS can be executed in the target system.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.161.0

- Add command to idle opt.
- Rename d3 entry event and add idle trigger param on
notify event.
- Add bit to fw boot status to notify status when hardware
is powered up.

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.160.0

- New parameter to define extra vblank stretch required when
doing FPO + Vactive
- Pass in pipe index for FPO

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.158.0

[Why & How]
Add boot control bit to control dispclk and dppclk deep sleep

Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drivers/gpu: fix typo in comment

Replace "isntance" with "instance".

Signed-off-by: Husain Alshehhi <husain@alshehhi.io>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: avoid unaligned access warnings

When building on OpenBSD/arm64 with clang 15, unaligned access
warnings are seen when a union is embedded inside a packed struct.

drm/amd/display/dmub/inc/dmub_cmd.h:941:18: error: field
cursor_copy_src within 'struct dmub_rb_cmd_mall' is less aligned than
'union dmub_addr' and is usually due to 'struct dmub_rb_cmd_mall'
being packed, which can lead to unaligned accesses
[-Werror,-Wunaligned-access]
union dmub_addr cursor_copy_src; /**< Cursor copy address */
^
drm/amd/display/dmub/inc/dmub_cmd.h:942:18: error: field cursor_copy_dst
within 'struct dmub_rb_cmd_mall' is less aligned than
'union dmub_addr' and is usually due to 'struct dmub_rb_cmd_mall'
being packed, which can lead to unaligned accesses
[-Werror,-Wunaligned-access]
union dmub_addr cursor_copy_dst; /**< Cursor copy destination */
^

Add pragma pack around dmub_addr to avoid this.

Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: temporary fix for page faulting

This reverts a part of the
commit 826e7ffaf079c72607bf3199d4e19730eaf8ca00
("drm/amd/display: [FW Promotion] Release 0.0.153.0")

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta<ayugupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Move DCN314 DOMAIN power control to DMCUB

[Why]
DOMAIN power gating control is now required to be done via firmware
due to interlock with other power features. This is to avoid
intermittent issues in the LB memories.

[How]
If the firmware supports the command then use the new firmware as
the sequence can avoid potential display corruption issues.

The command will be ignored on firmware that does not support DOMAIN
power control and the pipes will remain always on - frequent PG cycling
can cause the issue to occur on the old sequence, so we should avoid it.

Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.153.0

[Why&How]
- Reduce reserved size from 9 to 8 dwords to reduce structure size
and allow the union dmub_rb_cmd to fit into max 64-bytes cmd size

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Pass DSC slice height to PSR FW

[Why]
When DSC is enabled, the PSRSU seletive update region
must be multiple number of DSC slice height number.
The original solution is to overwrite the SU Y granularity
by DSC slice height in DAL driver. However, the size
of the SU Y granularity variable only has 8 bytes
and the DSC slice height may over the 8 bytes size.

[How]
Instead of overwriting the SU Y granularity value,
add a new DSC slice height pararmeter and pass it
to DMUB PSRSU FW. The PSRSU FW will refer to the
DSC slice height value and extend the SU region.

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Reviewed-by: ChunTao Tso <chuntao.tso@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Robin Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.150.0

- Add comments to reserved bit

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Skip backlight control delay on external powered links

[Why]
When an eDP panel is powered externally from a different GPU, we can avoid
waiting for hardware sequencing delays when switching the backlight on/off
as the display backlight is no longer powered by the original source.

[How]
This commit extends the 'link_powered_externally' variable to allow
bypassing hardware delays for additional backlight commands and force the
backlight on/off when a link is powered by another GPU.

Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Reviewed-by: Felipe Clark <felipe.clark@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Tony Tascioglu <tony.tascioglu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Optimize link power-down when link powered externally

[Why]
When an eDP panel is powered externally by a different GPU, we don't need
to wait for hardware sequencing delays when powering down a link, as the
display is not dependent on the GPU being powered down.

[How]
This commit adds a variable 'link_powered_externally' to indicate when a
link is being powered by another GPU.

Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Reviewed-by: Felipe Clark <felipe.clark@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Tony Tascioglu <tony.tascioglu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update dmub header to match DMUB

[WHY]
Last PR missed name of a struct to match in DMUB

[HOW]
Update the logic in dmub_cmh.h header

Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DPIA NOTIFICATION logic

[WHY]
Adding the new DPIA NOTIFY packets from DMUB
As per the design with Cruise to account for
250ms response delay otherwise

[HOW]
Added th DPIA NOTIFY logic as per DMUB logic

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add margin on DRR vblank start for subvp

[Description]
- Add margin for HUBP "jitter" for SubVp + DRR case
- Also do a min transition even if MPO is added on a
non SubVP pipe (i.e. added on DRR pipe for SubVP + DRR)

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.143.0

- New boot options to enable USB4 DP BW Allocation mode in DPIA

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Waiting for 1 frame to fix the flash issue on PSR1

[Why]
Needs more frames waiting before the PSR_Exit sending for the specific
TCON.

[How]
Add relock_delay_frame_cnt to control how many frames waiting are needed
before the PSR_Exit sending. The default value is 0. The Driver side can
set this variable for specific TCONs.

Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ryan Lin <tsung-hua.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.141.0

- Add flag as a status read back that indicates back to back
flips detected during psr.

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Document part of the DMUB cmd

Add a simple documentation in the dmub_cmd.

Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement secure display on DCN21

[Why]
Porting secure display feature from DCN10 to DCN21. Support single
display for now and will extend to multiple displays.

[How]
- use workqueue to offload works for dmub or dmcu firmware
- after receiving ROI update from userspace, set skip_frame_cnt to 1
- refactor amdgpu_dm_crtc_handle_crc_window_irq()
- disable PSR before activating secure_display on a crtc
- check if secure_display is activated before enabling psr
- only work for single display for now.

Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use set_vtotal_min_max to configure OTG VTOTAL

In multiple parts of the DCN code, we write directly to the
OTG_V_TOTAL_* registers in some OPTC functions. Let's avoid it by using
the set_vtotal_min_max.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Display does not light up after S4 resume

[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.

[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use the same cursor info across features

Since different features would need to update cursor registers, However,
they would use different approaches.

To unify varied methods, this refactor is implemented the same update
cursor info method for current varied features.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Max Tseng <Max.Tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cursor Info Update refactor

Dc: cursor info update: phase 1:

[Why]

Different feature might need to update cursor info, but
With different approaches.
To unify this diversity problem, all features should use
The same interface to update cursor.

Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.134.0

- Handle pipe split case for SubVP:
Pass in pipe split index for main and phantom pipes

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.132.0

- Fix comment to indicate correct visual confirm option

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add support for visual confirm color

[Why]
We want to get the visual confirm color of the bottom-most pipe
for test automation.

[How]
Save the visual confirm color to plane_state before program to MPC;

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.130.0

- For SubVP add scaling factor to allow firmware to calculate
accurate line to start programming

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add support for manual DMUB FAMS trigger

- Add is_drr parameter to indicate DRR is enabled on
the panel to determine whether SubVP MCLK switch
logic should be enabled

- Add DRR manual trigger in FW (instead of driver)
because manual trigger programming triggers DRR
update pending and can block SubVP MCLK switches
from taking place

Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add basic infrastructure for enabling FAMS

We want to enable Firmware Assisted Memory (FAMS) Switching, but first,
we need to add the required code infrastructure in DC before allowing it
in amdgpu_dm.

Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add SubVP required code

This commit enables the SubVP feature. To achieve that, we need to:

- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.119.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: align dmub cmd header to latest dmub FW to support PSR-SU

[why]
PSR-SU is implemented in upstreamed dmub FW but not enabled on
DM and DC. We'd add necessary and missing definitions in dmub
cmd header to align w/ the up-to-date DMUB FW for PSR-SU support.

[how]
Add definitions and items below into dmub cmd header:
- DMUB psr version enumeration for PSR-SU
- dirty rectangle structure
- psr debug flag of forcing full frame update
- dmub command of updating dirty rectangle and cursor infor
- dmub psr command type of setting sink vtotal in PSR active
- dmub psr su debug flags structure
- dmub cmd structure for
- updating dirty rectangle
- cursor infor
- setting sink vtotal
- dmub ringbuffer command items

Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DMCUB source files and changes for DCN32/321

DMCUB is the display engine microcontroller which aids in modesetting
and other display related features.

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.115.0

- Add new cmd for querying HPD state

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Connection Manager boot option.

[Why]
Boot up behaviour may differ depending on the Connection Manager
handling USB4 tunneling.

[How]
Send boot option to firmware to indicate Connection Manager.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.111.0

- Add options to allow for configurable PHY options during PSR active
state
- Remove unused versioning and git hash

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix unused-but-set-variable warning

Fix the kernel test robot warning below:

drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2893:12:
warning: variable 'temp' set but not used [-Wunused-but-set-variable]

Replaced the assignment to the unused temp variable with READ_ONCE()
macro to flush the writes. READ_ONCE() helps avoid the use of
volatile and makes it obvious from the code that the read here is
intentional. Also verified on x86 that the generated code is exactly the
same as before.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aashish Sharma <shraash@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.110.0

- Revert save/restore PANEL_PWRSEQ_REF_DIV2 and
other psr phy optimizations

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.109.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.108.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2

[why]
DCN31 has this in zstate save/restore sequence.
need for non_zstate supported ASIC

[how]
add this PANEL_PWRSEQ_REF_DIV2 to existing panel_cntl_hw_init structure.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.107.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.106.0

Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Adding a dc_debug option and dmub setting to use PHY FSM for PSR

[Why]
PSR Power on/off is done in PSR. Add a dc_debug option
and dmub setting to use PHY implementation of this instead.

[How]
Add a dc_debug option and dmub setting to use
PHY FSM Power up/down for PSR.

Co-authored-by: Shah Dharati <dharati.shah@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Shah Dharati <dharati.shah@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add cable ID support for usb c connector

[how]
Call to DMUB to retrieve usb c cable ID data from PD firmware.
If cable id is retrieved from DMUB, skip reading cable ID from RX.

Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove unused temp variable

Remove unused temp variable from the dmub_rb_flush_pending function by
using arithmetic to remove the loop.

The -Wunused-but-set-variable warning was pointed out by Clang with the
following warning:

drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2921:12: warning:
variable 'temp' set but not used [-Wunused-but-set-variable]
uint64_t temp;
^

v2: squash in revert and comment update (Alex)

Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.104.0

Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.103.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.102.0

- Correct number of reserved bits in cmd_lock_hw
- Extend bits of hw_lock_client to allow for more clients

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.101.0

- Add Scr8 for GPINT messaging between driver and fw

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.100.0

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.98

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.97

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Query DMCUB for dp alt status

[Why]
To avoid hanging RDPCSPIPE when INTERCEPTB isn't set.

DMCUB owns control of that bit so DMCUB should manage returning the
information driver needs for link encoder control.

[How]
Add a new DMCUB command to return dp alt disable and dp4 information.

Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.96

Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Rename a struct field to describe a cea component better

[why]
Need to fix the code so it does not use reserved keywords

[how]
Change the total_length member of the cea struct

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.95

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.94

[Why & How]
- Remove tick count definition since it can be different
per HW revision

Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.93

- Fix ARR39-C issue with scaled integer addition in rb func

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.92

Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable DSC over eDP

[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled

[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: To support sending TPS3 pattern when restoring link

[Why]
Some panels require to use TPS3 pattern to wake up link in PSR mode.

[How]
To add TPS3 selection information in PSR settings command and pass to
DMUB FW.

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.91

Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: MST support for DPIA

[Why]
- DPIA MST slot registers are not programmed during payload
allocation and hence MST does not work with DPIA.
- HPD RX interrupts are not handled for DPIA.

[How]
- Added inbox command to program the MST slots whenever
payload allocation happens for DPIA links.
- Added support for handling HPD RX interrupts

Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set phy_mux_sel bit in dmub scratch register

[Why]
B0 has pipe mux for DIGC and DIGD which can be connected to PHYF/PHYG or
PHYC/PHY D.

[How]
Based on chip internal hardware revision id determine it is B0 and set
DMUB scratch register so DMUBFW can connect the display pipe is
connected correctly to the dig.

Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hansen <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.90

Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.89

- Add flag to control root clock gating in init_hw
- Add flag to indicate a diags environment is being used

Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: dc_link_set_psr_allow_active refactoring

[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.88

Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dpia debug options

[Why & How]
To add support for dpia debug options.

Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Support for SET_CONFIG processing with DMUB

[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.

[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Stub out DPIA link training call

[why & how]
Add stub for DPIA link training and define new DPIA DMUB commands
to support it.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Support for DMUB HPD and HPD RX interrupt handling

[WHY]
To add support for HPD & HPD RX interrupt handling for USB4 DPIA in
YELLOW_CARP_B0. USB4 DPIA HPD & HPD RX interrupts are issued from DMUB to
driver as a outbox1 message.

[HOW]
1) Created get_link_index_from_dpia_port_index() to retrieve link index
from dpia port index for HPD & HPD RX dmub notifications.
2) Added DMUB HPD & HPD RX handling in dmub_srv_stat_get_notification().

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.87

Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.86

Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add vsync notify to dmub for abm pause

[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.

[How]
Send inbox message to notify ABM pause based on vsync on/off

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.85

Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.84

Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Creating a fw boot options bit for an upcoming feature

[Why]
Need a bit for x86 driver to enable a FW boot option for an upcoming
feature.

[How]
Added a bit in dmub_fw_boot_options for an upcoming feature.

Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.83

Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.82

* PSR SMU optimizations
* MST dock fixes

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.81

* PSR optimizations
* add support for ABM when ODM is enabled
* Z10 with PSR fixes
* Increase trace buffer

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.80

- Add volatile to avoid incomplete flushing of data in rb

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 BIOS and DMUB Support

Parse DP2 encoder caps and hpo instance from bios

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

isystem: trim/fixup stdarg.h and other headers

Delete/fixup few includes in anticipation of global -isystem compile
option removal.

Note: crypto/aegis128-neon-inner.c keeps <stddef.h> due to redefinition
of uintptr_t error (one definition comes from <stddef.h>, another from
<linux/types.h>).

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

drm/amd/display: [FW Promotion] Release 0.0.79

Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Ensure DCN save after VM setup

[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.

[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.

v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.78

Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Correct comment style

Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.77

Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.76

Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.75

- Add reserved bits for future feature development
- Fix issue with mismatch with type const
- Replaced problematic code with old memcpy and casted problematic
pointers to unsigned char pointers

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refine condition for cursor visibility

[why]
There's a special case where upper plane is not the main plane. If it owns
the cursor, it will be invisible in the majority of the screen.

[How]
The condition for disabling cursor is changed:
- check if upper viewport completely covers current. This was the
previous change that doesn't handle all scenarios with pipe splitting.
- if not, show the cursor only if it's not scaled or no upper pipe.

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.73

- Add reserved bits for future feature development
- Fix issue with mismatch with type const

Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Extend dmub_cmd_psr_copy_settings_data struct

Reserve padding bytes for new feature implementation

Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.72

- Updated SCR definition for FW boot options for Separate DCN init
for DMUB FW loaded in VBL

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Ensure DCN save after VM setup

[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.

[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.

v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: fold DRM_AMD_DC_DCN3_1 into DRM_AMD_DC_DCN

No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.71

- Introduce CMD for EDID CEA block parsing
- Add SCR5 definition for reporting eDP power sequencer status

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.70

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.69

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.68

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove unused definition of DMUB SET_CONFIG

[Why & How]
SET_CONFIG transactions with DMUB is not used and removed.

Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enabling PSR support for multiple panels

[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all

Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN3.1 DMCUB

DMCU-B (Display Micro-Controller Unit B) is a display microcontroller
used for shared display functionality with BIOS and for advanced
power saving display features.

Extends the command header to include new DCN3.1 functionality.

Adds new interfaces to DC dmub interface as well for z-state support.

Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.66

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.65

- Implement INBOX0 messaging for HW lock

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.64

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.63

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Added multi instance support for ABM

[WHY & HOW]
ABM assumes only 1 eDP is connected. Refactored existing
ABM interface to support multiple instances.

Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.62

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.61

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Added support for multiple eDP BL control

[WHY & HOW]
Driver currently assumes only 1 eDP is connected. Added support for
multiple eDP BL control.

Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.60

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.59

[How&Why]
add params to send FEC status to firmware

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.58

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Removing unused code from dmub_cmd.h

Removing code that is not used at the moment.

Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.57

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.56

More updates to the comments to better describe the function of
different cmds and parameters in the dmub interface.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.55

Add comments to better describe the function of different cmds
and parameters in the dmub interface

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Move define from internal header to dmub_cmd.h

[Why & How]
Fix linux compile error

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.54

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement dmub trace event

[Why & How]
DMUB FW send trace event via outbox0 interrupt. Driver will handle it.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.53

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.52

[How]
Add new aux cmd fields for acquire and release

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.51

Add new definition and union for dmub_rb_cmd_dig1_transmitter_control

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.50

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.49

- Add field for passing line time for a frame

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update dcn30_apply_idle_power_optimizations() code

Update the function for idle optimizations
-remove hardcoded size
-enable no memory-request case
-add cursor copy
-update mall eligibility check case

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.48

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.47

- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.46

- Add new aux_channel_type
- Changed port_index to instance in dmub_cmd_dp_aux_control_data
- Change aux_return_code_type to sync up with driver
- param for ramping abm based on backlight level

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.45

- Add define for __forceinline

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.44

Add feature caps to allow way for driver to query what features
FW supports

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.42

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dual edp optimization flag.

[Why & How]
Add a dual edp power optimization flag, so driver will
notify this flag to dmub FW to determine if apply the
power optimization.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update dmub code

There is a delta in the dmub code
- add boot options
- add boot status
- remove unused auto_load_is_done func pointer

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.41

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.40

[Header Changes]
- Add command for retrieving PSR residency
- Add command for forcing PSR static

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.39

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.38

| [Header Changes]
| - Add new SCRATCH15 boot option and fw_state member to skip
| phy access
| - Add new SCRATCH15 boot option and fw_state member to disable
| clk gating
| - Add defines for AUX return status
| - Add defines for HPD events

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.37

| [Header Changes]
| - Add GPINT to change timestamping mode for traces

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: add MALL support (v2)

Enable Memory Access at Last Level (MALL) feature for display.

v2: squash in 64 bit division fixes

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.36

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.35

[Header Changes]
- Definition for retaining ABM settings during disable
- Addition of some new AUX interface definitions
- Addition of some outbox definitions

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.34

[Header Changes]
- Add new SCRATCH0 status bits for detecting restore state

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.33

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove set but used 'temp'

Addresses the following gcc warning with "make W=1":

In file included from drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../dmub_srv.h:67:0,
from drivers/gpu/drm/amd/amdgpu/../display/dmub/src/dmub_dcn21.c:26:
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../inc/dmub_cmd.h: In function ‘dmub_rb_flush_pending’:
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../inc/dmub_cmd.h:795:12: warning: variable ‘temp’ set but not used
[-Wunused-but-set-variable]
uint64_t temp;
^
In file included from drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../dmub_srv.h:67:0,
from drivers/gpu/drm/amd/amdgpu/../display/dmub/src/dmub_dcn30.c:26:
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../inc/dmub_cmd.h: In function ‘dmub_rb_flush_pending’:
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/../inc/dmub_cmd.h:795:12: warning: variable ‘temp’ set but not used
[-Wunused-but-set-variable]
uint64_t temp;

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.32

| [Header Changes]
| - Add debug flag to log line numbers for PSR debug

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.31

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.30

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.29

[Header Changes]
- Add command for panel power seq control

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.28

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.27

| [Header Changes]
| - Reworked the FW versioning to include hotfix
| and test bits

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.26

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.25

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.24

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.23

[Header Changes]
- Drop unused firmware SCRATCH bits from interface

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.22

[Header Changes]
- Add command for notification of active streams to DMUB

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.21

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.20

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.19

[Header Changes]
- Add debug flag for psr to use hw locking mgr state machine

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.18

[Header Changes]
- Update scratch information for boot status

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.17

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.16

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use dmub fw to lock pipe, cursor, dig

[Why]
Hw lock manager adds the ability to lock pipe, cursor, and dig in fw.

[How]
Send hw lock command to fw to lock pipe, cursor, and dig.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.15

[Header Changes]
- Add new initialization bits for driver to check
firmware status
- Add command for HW locking via DMUB

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.14

[Header Changes]
- Add SDP transmission deadline for PSR config cmd

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.13

[Header Changes]
- Version bump to 1.0.13

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 1.0.12

[Header Changes]
- Combine all interface dependencies between driver and fw into a
single header file
- Add FW Versioning to the dmub_cmd.h file

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: combine public interfaces into single header

[Why]
We want to better encapsulate all driver-fw dependencies into a single
file.

[How]
Combine all the headers under inc folder into a single header

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: FW release 1.0.10

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement some asic specific abm call backs.

[Why & How]
Implement abm set_pipe call stacks
Have some asics speicifc call stacks for abm.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add struct field for future use

Add dmub related struct field for future use.

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add panel cntl id for set backlight level.

[Why & How]
Add panel cntl instance when calling set backlight.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: clean up some header paths

[Why]
Some include paths don't need to have relative paths
And some types missing

[How]
make some changes to headers and modify include path

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Various fixes for PSR on DMCUB

[Why]
- Driver does not recognize new definitions of psr states.
- Internal tool is required for checking if psr is active.

[How]
- Parse psr state correctly so that driver will recognize psr state.
- Add visual confirmation that psr is active using existing mechanisms.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add ABM driver implementation

[Why]
Moving ABM from DMCU to DMCUB.

[How]
Add ABM driver files and implementation.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add ABM command structs to DMCUB

[Why]
Moving ABM from DMCU to DMCUB.

[How]
Add ABM command structs.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove unused values from psr struct

[Why]
Taking up unnecessary space.

[How]
Remove unused values from psr struct.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add set psr version message

[Why]
Must know psr version during runtime.

[How]
Add set psr version message structures.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Only program surface flip for video plane via dmcub

Only need to do surface flip for video plane via dmcub.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor surface flip programming

Rework surface programming for RN to separate preparing parameters and
register programming.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: DMCUB FW Changes to support PSR

[Why]
Moving PSR from DMCU to DMCUB.

[How]
Cleanup psr spec files and add PSR hw programming files.
No functionality is included in this change.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: programing surface flip by dmcub.

Programming surface flip addresses via dmcub uC for optimizing the data
flush.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Driverside changes to support PSR in DMCUB

[Why]
Moving PSR from DMCU to DMCUB.

[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Split DMUB cmd type into type/subtype

[Why]
Commands will be considered a stable ABI between driver and firmware.

Commands are also split between DC commands, DAL feature commands,
and VBIOS commands.

Commands are currently not designated to a specific ID and the enum
does not provide a stable ABI.

We currently group all of these into a single command type of 8-bits.
With the stable ABI consideration in mind it's not unreasonable to
run out of command IDs.

For cleaner separation and versioning split the commands into a main
type and a subtype.

[How]
For commands where performance matters (like reg sequences) these
are still considered main commands.

Sub commands will be split by ownership/feature.

Update existing command sequences to reflect new changes.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Navi10 DMUB VBIOS code

[Why]
We need some extra dmub_cmd_type for NV10

[How]
Add command table functions in DMUB firmware.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Xiong Yan <Xiong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add the DMUB service

The DMUB service is the interface to the DMCUB.

It's required to support Renoir features so it will be enabled and
compiled automatically when the Renoir display engine is enabled via
CONFIG_DRM_AMD_DC_DCN2_1.

DMUB code will initially be guarded by CONFIG_DRM_AMD_DC_DMUB and later
switched to CONFIG_DRM_AMD_DC_DCN2_1 with the config option dropped.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>