powerpc: move the ARCH_DMA_MINALIGN definition to asm/cache.h

Patch series "Move the ARCH_DMA_MINALIGN definition to asm/cache.h".

The ARCH_KMALLOC_MINALIGN reduction series defines a generic
ARCH_DMA_MINALIGN in linux/cache.h:

https://lore.kernel.org/r/20230612153201.554742-2-catalin.marinas@arm.com/

Unfortunately, this causes a duplicate definition warning for
microblaze, powerpc (32-bit only) and sh as these architectures define
ARCH_DMA_MINALIGN in a different file than asm/cache.h. Move the macro
to asm/cache.h to avoid this issue and also bring them in line with the
other architectures.


This patch (of 3):

The powerpc architecture defines ARCH_DMA_MINALIGN in asm/page_32.h and
only if CONFIG_NOT_COHERENT_CACHE is enabled (32-bit platforms only).
Move this macro to asm/cache.h to allow a generic ARCH_DMA_MINALIGN
definition in linux/cache.h without redefine errors/warnings.

Link: https://lkml.kernel.org/r/20230613155245.1228274-1-catalin.marinas@arm.com
Link: https://lkml.kernel.org/r/20230613155245.1228274-2-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306131053.1ybvRRhO-lkp@intel.com/
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rich Felker <dalias@libc.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

powerpc/32s: Cleanup around PTE_FLAGS_OFFSET in hash_low.S

PTE_FLAGS_OFFSET is defined in asm/page_32.h and used only
in hash_low.S

And PTE_FLAGS_OFFSET nullity depends on CONFIG_PTE_64BIT

Instead of tests like #if (PTE_FLAGS_OFFSET != 0), use
CONFIG_PTE_64BIT related code.

Also move the definition of PTE_FLAGS_OFFSET into hash_low.S
directly, that improves readability.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f5bc21db7a33dab55924734e6060c2e9daed562e.1606247495.git.christophe.leroy@csgroup.eu

powerpc/32: Add warning on misaligned copy_page() or clear_page()

copy_page() and clear_page() expect page aligned destination, and
use dcbz instruction to clear entire cache lines based on the
assumption that the destination is cache aligned.

As shown during analysis of a bug in BTRFS filesystem, a misaligned
copy_page() can create bugs that are difficult to locate (see Link).

Add an explicit WARNING when copy_page() or clear_page() are called
with misaligned destination.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204371
Link: https://lore.kernel.org/r/c6cea38f90480268d439ca44a645647e260fff09.1565941808.git.christophe.leroy@c-s.fr

powerpc/8xx: reintroduce 16K pages with HW assistance

Using this HW assistance implies some constraints on the
page table structure:
- Regardless of the main page size used (4k or 16k), the
level 1 table (PGD) contains 1024 entries and each PGD entry covers
a 4Mbytes area which is managed by a level 2 table (PTE) containing
also 1024 entries each describing a 4k page.
- 16k pages require 4 identifical entries in the L2 table
- 512k pages PTE have to be spread every 128 bytes in the L2 table
- 8M pages PTE are at the address pointed by the L1 entry and each
8M page require 2 identical entries in the PGD.

In order to use hardware assistance with 16K pages, this patch does
the following modifications:
- Make PGD size independent of the main page size
- In 16k pages mode, redefine pte_t as a struct with 4 elements,
and populate those 4 elements in __set_pte_at() and pte_update()
- Adapt the size of the hugepage tables.
- Define a PTE_FRAGMENT_NB so that a 16k page contains 4 page tables.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc32: Remove clear_pages() and define clear_page() inline

clear_pages() is never used expect by clear_page, and PPC32 is the
only architecture (still) having this function. Neither PPC64 nor
any other architecture has it.

This patch removes clear_pages() and moves clear_page() function
inline (same as PPC64) as it only is a few isns

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

dma-mapping: rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN

Now each architecture has the own dma_get_cache_alignment implementation.

dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.

This patch:

dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.

Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

asm-generic: rename page.h and uaccess.h

The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.

Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

powerpc/44x: Support for 256KB PAGE_SIZE

This patch adds support for 256KB pages on ppc44x-based boards.

For simplification of implementation with 256KB pages we still assume
2-level paging. As a side effect this leads to wasting extra memory space
reserved for PTE tables: only 1/4 of pages allocated for PTEs are
actually used. But this may be an acceptable trade-off to achieve the
high performance we have with big PAGE_SIZEs in some applications (e.g.
RAID).

Also with 256KB PAGE_SIZE we increase THREAD_SIZE up to 32KB to minimize
the risk of stack overflows in the cases of on-stack arrays, which size
depends on the page size (e.g. multipage BIOs, NTFS, etc.).

With 256KB PAGE_SIZE we need to decrease the PKMAP_ORDER at least down
to 9, otherwise all high memory (2 ^ 10 * PAGE_SIZE == 256MB) we'll be
occupied by PKMAP addresses leaving no place for vmalloc. We do not
separate PKMAP_ORDER for 256K from 16K/64K PAGE_SIZE here; actually that
value of 10 in support for 16K/64K had been selected rather intuitively.
Thus now for all cases of PAGE_SIZE on ppc44x (including the default, 4KB,
one) we have 512 pages for PKMAP.

Because ELF standard supports only page sizes up to 64K, then you should
use binutils later than 2.17.50.0.3 with '-zmax-page-size' set to 256K
for building applications, which are to be run with the 256KB-page sized
kernel. If using the older binutils, then you should patch them like follows:

--- binutils/bfd/elf32-ppc.c.orig
+++ binutils/bfd/elf32-ppc.c

-#define ELF_MAXPAGESIZE 0x10000
+#define ELF_MAXPAGESIZE 0x40000

One more restriction we currently have with 256KB page sizes is inability
to use shmem safely, so, for now, the 256KB is available only if you turn
the CONFIG_SHMEM option off (another variant is to use BROKEN).
Though, if you need shmem with 256KB pages, you can always remove the !SHMEM
dependency in 'config PPC_256K_PAGES', and use the workaround available here:
http://lkml.org/lkml/2008/12/19/20

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

powerpc/44x: Support 16K/64K base page sizes on 44x

This adds support for 16k and 64k page sizes on PowerPC 44x processors.

The PGDIR table is much smaller than a page when using 16k or 64k
pages (512 and 32 bytes respectively) so we allocate the PGDIR with
kzalloc() instead of __get_free_pages().

One PTE table covers rather a large memory area when using 16k or 64k
pages (32MB or 512MB respectively), so we can easily put FIXMAP and
PKMAP in the area covered by one PTE table.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

POWERPC: Allow 32-bit hashed pgtable code to support 36-bit physical

This rearranges a bit of code, and adds support for
36-bit physical addressing for configs that use a
hashed page table. The 36b physical support is not
enabled by default on any config - it must be
explicitly enabled via the config system.

This patch *only* expands the page table code to accomodate
large physical addresses on 32-bit systems and enables the
PHYS_64BIT config option for 86xx. It does *not*
allow you to boot a board with more than about 3.5GB of
RAM - for that, SWIOTLB support is also required (and
coming soon).

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

powerpc: Move include files to arch/powerpc/include/asm

from include/asm-powerpc. This is the result of a

mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm

Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>