mips: Add MIPS Warrior P5600 support

This is a MIPS32 Release 5 based IP core with XPA, EVA, dual/quad issue
exec pipes, MMU with two-levels TLB, UCA, MSA, MDU core level features
and system level features like up to six P5600 calculation cores, CM2
with L2 cache, IOCU/IOMMU (though might be unused depending on the
system-specific IP core configuration), GIC, CPC, virtualisation module,
eJTAG and PDtrace.

As being MIPS32 Release 5 based core it provides all the features
available by the CPU_MIPS32_R5 config, while adding a few more like
UCA attribute support, availability of CPU-freq (by means of L2/CM
clock ratio setting), EI/VI GIC modes detection at runtime.

In addition to this if P5600 architecture is enabled modern GNU GCC
provides a specific tuning for P5600 processors with respect to the
classic MIPS32 Release 5. First of all branch-likely avoidance is
activated only when the code is compiled with the speed optimization
(avoidance is always enabled for the pure MIPS32 Release 5
architecture). Secondly the madd/msub avoidance is enabled since
madd/msub utilization isn't profitable due to overhead of getting the
result out of the HI/LO registers. Multiply-accumulate instructions are
activated and utilized together with the necessary code reorder when
multiply-add/multiply-subtract statements are met. Finally load/store
bonding is activated by default. All of these optimizations may make
the code relatively faster than if just MIP32 release 5 architecture
was requested.

Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

mips: Add MIPS Release 5 support

There are five MIPS32/64 architecture releases currently available:
from 1 to 6 except fourth one, which was intentionally skipped.
Three of them can be called as major: 1st, 2nd and 6th, that not only
have some system level alterations, but also introduced significant
core/ISA level updates. The rest of the MIPS architecture releases are
minor.

Even though they don't have as much ISA/system/core level changes
as the major ones with respect to the previous releases, they still
provide a set of updates (I'd say they were intended to be the
intermediate releases before a major one) that might be useful for the
kernel and user-level code, when activated by the kernel or compiler.
In particular the following features were introduced or ended up being
available at/after MIPS32/64 Release 5 architecture:
+ the last release of the misaligned memory access instructions,
+ virtualisation - VZ ASE - is optional component of the arch,
+ SIMD - MSA ASE - is optional component of the arch,
+ DSP ASE is optional component of the arch,
+ CP0.Status.FR=1 for CP1.FIR.F64=1 (pure 64-bit FPU general registers)
must be available if FPU is implemented,
+ CP1.FIR.Has2008 support is required so CP1.FCSR.{ABS2008,NAN2008} bits
are available.
+ UFR/UNFR aliases to access CP0.Status.FR from user-space by means of
ctc1/cfc1 instructions (enabled by CP0.Config5.UFR),
+ CP0.COnfig5.LLB=1 and eretnc instruction are implemented to without
accidentally clearing LL-bit when returning from an interrupt,
exception, or error trap,
+ XPA feature together with extended versions of CPx registers is
introduced, which needs to have mfhc0/mthc0 instructions available.

So due to these changes GNU GCC provides an extended instructions set
support for MIPS32/64 Release 5 by default like eretnc/mfhc0/mthc0. Even
though the architecture alteration isn't that big, it still worth to be
taken into account by the kernel software. Finally we can't deny that
some optimization/limitations might be found in future and implemented
on some level in kernel or compiler. In this case having even
intermediate MIPS architecture releases support would be more than
useful.

So the most of the changes provided by this commit can be split into
either compile- or runtime configs related. The compile-time related
changes are caused by adding the new CONFIG_CPU_MIPS32_R5/CONFIG_CPU_MIPSR5
configs and concern the code activating MIPSR2 or MIPSR6 already
implemented features (like eretnc/LLbit, mthc0/mfhc0). In addition
CPU_HAS_MSA can be now freely enabled for MIPS32/64 release 5 based
platforms as this is done for CPU_MIPS32_R6 CPUs. The runtime changes
concerns the features which are handled with respect to the MIPS ISA
revision detected at run-time by means of CP0.Config.{AT,AR} bits. Alas
these fields can be used to detect either r1 or r2 or r6 releases.
But since we know which CPUs in fact support the R5 arch, we can manually
set MIPS_CPU_ISA_M32R5/MIPS_CPU_ISA_M64R5 bit of c->isa_level and then
use cpu_has_mips32r5/cpu_has_mips64r5 where it's appropriate.

Since XPA/EVA provide too complex alterationss and to have them used with
MIPS32 Release 2 charged kernels (for compatibility with current platform
configs) they are left to be setup as a separate kernel configs.

Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

arch: split MODULE_ARCH_VERMAGIC definitions out to <asm/vermagic.h>

As the bug report [1] pointed out, <linux/vermagic.h> must be included
after <linux/module.h>.

I believe we should not impose any include order restriction. We often
sort include directives alphabetically, but it is just coding style
convention. Technically, we can include header files in any order by
making every header self-contained.

Currently, arch-specific MODULE_ARCH_VERMAGIC is defined in
<asm/module.h>, which is not included from <linux/vermagic.h>.

Hence, the straight-forward fix-up would be as follows:

|--- a/include/linux/vermagic.h
|+++ b/include/linux/vermagic.h
|@@ -1,5 +1,6 @@
| /* SPDX-License-Identifier: GPL-2.0 */
| #include <generated/utsrelease.h>
|+#include <linux/module.h>
|
| /* Simply sanity version stamp for modules. */
| #ifdef CONFIG_SMP

This works enough, but for further cleanups, I split MODULE_ARCH_VERMAGIC
definitions into <asm/vermagic.h>.

With this, <linux/module.h> and <linux/vermagic.h> will be orthogonal,
and the location of MODULE_ARCH_VERMAGIC definitions will be consistent.

For arc and ia64, MODULE_PROC_FAMILY is only used for defining
MODULE_ARCH_VERMAGIC. I squashed it.

For hexagon, nds32, and xtensa, I removed <asm/modules.h> entirely
because they contained nothing but MODULE_ARCH_VERMAGIC definition.
Kbuild will automatically generate <asm/modules.h> at build-time,
wrapping <asm-generic/module.h>.

[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic

Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>

MIPS: Loongson: Rename LOONGSON1 to LOONGSON32

Now old Loongson-2E/2F use LOONGSON2EF and will be removed in future,
newer Loongson-2/3 use LOONGSON64. So rename LOONGSON1 to LOONGSON32
will make the naming style more unified.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paulburton@kernel.org: Fix checkpatch whitespace warning in irqflags.h]
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@vger.kernel.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>

MIPS: Loongson64: Rename CPU TYPES

CPU_LOONGSON2 -> CPU_LOONGSON2EF
CPU_LOONGSON3 -> CPU_LOONGSON64

As newer loongson-2 products (2G/2H/2K1000) can share kernel
implementation with loongson-3 while 2E/2F are less similar with
other LOONGSON64 products.

Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: chenhc@lemote.com
Cc: paul.burton@mips.com

MIPS: Remove unused R8000 CPU support

Our R8000 CPU support can only be included if a system selects
CONFIG_SYS_HAS_CPU_R8000. No system does, making all R8000-related CPU
support dead code. Remove it.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

MIPS: Remove unused R5432 CPU support

Our R5432 CPU support can only be included if a system selects
CONFIG_SYS_HAS_CPU_R5432. No system does, making all R5432-related CPU
support dead code. Remove it.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

MIPS: Remove unused R4300 CPU support

Our R4300 CPU support can only be included if a system selects
CONFIG_SYS_HAS_CPU_R4300. No system does, making all R4300-related CPU
support dead code. Remove it.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Remove unused R6000 support

The kernel contains a small amount of incomplete code aimed at
supporting old R6000 CPUs. This is:

- Unused, as no machine selects CONFIG_SYS_HAS_CPU_R6000.

- Broken, since there are glaring errors such as r6000_fpu.S moving
the FCSR register to t1, then ignoring it & instead saving t0 into
struct sigcontext...

- A maintenance headache, since it's code that nobody can test which
nevertheless imposes constraints on code which it shares with other
machines.

Remove this incomplete & broken R6000 CPU support in order to clean up
and in preparation for changes which will no longer need to consider
dragging the pretense of R6000 support along with them.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: module: Unify rel & rela reloc handling

The module load code has previously had entirely separate
implementations for rel & rela style relocs, which unnecessarily
duplicates a whole lot of code. Unify the implementations of both types
of reloc, sharing the bulk of the code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

mips: separate extable.h, switch module.h to it

more victims of indirect include chains - au1200fb
lasat/picvue_proc and watchdog/ath79_wdt

... as well as tb0219, spotted by Sudip Mukherjee

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

MIPS: asm: module: define MODULE_PROC_FAMILY for MIPS R6

Define the MODULE_PROC_FAMILY for the MIPS R6 ISA.

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS: MT: Remove SMTC support

Nobody is maintaining SMTC anymore and there also seems to be no userbase.
Which is a pity - the SMTC technology primarily developed by Kevin D.
Kissell <kevink@paralogos.com> is an ingenious demonstration for the MT
ASE's power and elegance.

Based on Markos Chandras <Markos.Chandras@imgtec.com> patch
https://patchwork.linux-mips.org/patch/6719/ which while very similar did
no longer apply cleanly when I tried to merge it plus some additional
post-SMTC cleanup - SMTC was a feature as tricky to remove as it was to
merge once upon a time.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: Add basic Loongson-3 definition

Loongson-3 is a multi-core MIPS family CPU, it support MIPS64R2 fully.
Loongson-3 has the same IMP field (0x6300) as Loongson-2.

Loongson-3 has a hardware-maintained cache, system software doesn't
need to maintain coherency.

Loongson-3A is the first revision of Loongson-3, and it is the quad-
core version of Loongson-2G. Loongson-3A has a simplified version named
Loongson-2Gq, the main difference between Loongson-3A/2Gq is 3A has two
HyperTransport controller but 2Gq has only one. HT0 is used for cross-
chip interconnection and HT1 is used to link PCI bus. Therefore, 2Gq
cannot support NUMA but 3A can. For software, Loongson-2Gq is simply
identified as Loongson-3A.

Exsisting Loongson family CPUs:
Loongson-1: Loongson-1A, Loongson-1B, they are 32-bit MIPS CPUs.
Loongson-2: Loongson-2E, Loongson-2F, Loongson-2G, they are 64-bit
single-core MIPS CPUs.
Loongson-3: Loongson-3A(including so-called Loongson-2Gq), they are
64-bit multi-core MIPS CPUs.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6629/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: PMC-Sierra Yosemite: Remove support.

Nobody seems to be interested anymore and upstream also never had an
ethernet driver.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Make most arch asm/module.h files use asm-generic/module.h

Use the mapping of Elf_[SPE]hdr, Elf_Addr, Elf_Sym, Elf_Dyn, Elf_Rel/Rela,
ELF_R_TYPE() and ELF_R_SYM() to either the 32-bit version or the 64-bit version
into asm-generic/module.h for all arches bar MIPS.

Also, use the generic definition mod_arch_specific where possible.

To this end, I've defined three new config bools:

(*) HAVE_MOD_ARCH_SPECIFIC

Arches define this if they don't want to use the empty generic
mod_arch_specific struct.

(*) MODULES_USE_ELF_RELA

Arches define this if their modules can contain RELA records. This causes
the Elf_Rela mapping to be emitted and allows apply_relocate_add() to be
defined by the arch rather than have the core emit an error message.

(*) MODULES_USE_ELF_REL

Arches define this if their modules can contain REL records. This causes
the Elf_Rel mapping to be emitted and allows apply_relocate() to be
defined by the arch rather than have the core emit an error message.

Note that it is possible to allow both REL and RELA records: m68k and mips are
two arches that do this.

With this, some arch asm/module.h files can be deleted entirely and replaced
with a generic-y marker in the arch Kbuild file.

Additionally, I have removed the bits from m32r and score that handle the
unsupported type of relocation record as that's now handled centrally.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

MIPS: Fix race condition in module relocation code.

The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace. In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore. Fix race by moving it into
mod_arch_specific.

[ralf@linux-mips.org: folded in Tony's followup fix. Thanks Tony!]

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/

MIPS: Add CPU support for Loongson1B

Loongson 1B is a 32-bit SoC designed by Institute of Computing Technology
(ICT) and the Chinese Academy of Sciences (CAS), which implements the
MIPS32 release 2 instruction set.

[ralf@linux-mips.org: But which is not strictly a MIPS32 compliant device
which also is why it identifies itself with the Legacy Vendor ID in the
PrID register. When applying the patch I shoveled some code around to
keep things in alphabetical order and avoid forward declarations.]

Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Cc: To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: zhzhl555@gmail.com
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3976/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Delete bogus module.h usage in termios.h

There is no need for this. Removing it causes a small amount of fallout
(shown below) due to a few implicit header presence assumptions that are
easily fixed.

arch/mips/include/asm/termios.h:103: error: implicit declaration of function 'access_ok'
arch/mips/include/asm/module.h:17: error: expected specifier-qualifier-list before 'Elf64_Addr'

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3449/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Netlogic: XLP CPU support.

Add support for Netlogic's XLP MIPS SoC. This patch adds:
* XLP processor ID in cpu_probe.c and asm/cpu.h
* XLP case to asm/module.h
* CPU_XLP case to mm/tlbex.c
* minor change to r4k cache handling to ignore XLP secondary cache
* XLP cpu overrides to mach-netlogic/cpu-feature-overrides.h

Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2966/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BMIPS: Add CFLAGS, Makefile entries for BMIPS

Add CONFIG_CPU_BMIPS* in all of the right places, so that BMIPS kernel
images will compile and run.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2955/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Netlogic: Cache, TLB support and feature overrides for XLR

CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.

Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add Cavium OCTEON processor constants and CPU probe.

Add OCTEON constants to asm/cpu.h and asm/module.h.

Add probe function for Cavium OCTEON CPUs and hook it up.

Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors

We already have sufficient infrastructure to support VR5500 and VR5500A
series processors. Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.

This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Move headfiles to new location below arch/mips/include

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>