Copy stable/9 to releng/9.3 as part of the 9.3-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Toss bogus mergeinfo.

MFC r235634

Fix and update battery status bits according to linux driver

Copy head to stable/9 as part of 9.0-RELEASE release cycle.

Approved by: re (implicit)

Merge from projects/mips to head by hand:

Defintions for cavium uart (do they belong here?)

add %b formats for various registers

- Cleanup i8251 related defines.
- Move i8255 related defines into a separate file.

unifdef PC98

Support for Freescale QUad Integrated Communications Controller.

The QUICC engine is found on various Freescale parts including MPC85xx, and
provides multiple generic time-division serial channel resources, which are in
turn muxed/demuxed by the Serial Communications Controller (SCC).

Along with core QUICC/SCC functionality a uart(4)-compliant device driver is
provided which allows for serial ports over QUICC/SCC.

Approved by: cognet (mentor)
Obtained from: Juniper
MFp4: e500

Fix style nits. No md5 changes in .o's. ;-)

Enhanced floppy controllers have Data Rate Select Register (DSR) at 0x3f4.
Use it to reset controller and to select data rate. According to Intel
80277AA datasheet, software reset behaves the same as DOR reset except
that it is self clearing. National Semiconductor PC8477B datasheet says
the same. As a side effect, we no longer use Configuration Control
Register (CCR) at 0x3f7 for these controllers, which is often missing
in modern hardware.

Allow uart(4)'s ns8250 driver to work with devices whose regshift is > 0.

- Rename REG_DL to REG_DLL and REG_DLH.
- Always treat DLL and DLH as two separate 8-bit registers instead of one
16-bit register.

Additionally, remove the probe for the high 4 bits of IER being 0 and don't
assume we can always read/write 0 to/from those bits.

These changes allow uart(4) to drive the UARTs on the Intel XScale PXA255.

Reviewed by: marcel

MFp4:
Add CHAN_A & CHAN_B for channel register offsets.
While here, fix a comment.

Register definitions for the ancient via6522. This 20+ year-old chip
still exists as a cell in the Macio asic on Apples, and is used to communicate
through the shift register with the external PMU microcontroller.

Typo.

PR: misc/87679
Submitted by: Alan Amesbury <amesbury umn.edu>

cosmetic change.

- Move bus dependent defines to {isa,cbus}_dmareg.h.
- Use isa/isareg.h rather than <arch>/isa/isa.h.

Tested on: i386, pc98

- Move timerreg.h to <arch>/include and split i8253 specific defines into
i8253reg.h, and add some defines to control a speaker.
- Move PPI related defines from i386/isa/spkr.c into ppireg.h and use them.
- Move IO_{PPI,TIMER} defines into ppireg.h and timerreg.h respectively.
- Use isa/isareg.h rather than <arch>/isa/isa.h.

Tested on: i386, pc98

Since we are quite unlikely to ever face another platform which
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.

Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.

Start each of the license/copyright comments with /*-, minor shuffle of lines

This file was repocopied from sys/dev/uart/uart_dev_z8530.h.

This file was repocopied from sys/dev/uart/uart_dev_sab82532.h.

o Remove the com_thr, com_rhr, com_isr and com_lctl defines. They are
not used and aliases for other defines.
o Add REG_DATA as an alias for com_data. Likewise for other register
defines.
o Add LCR_SBREAK and make CFCR_SBREAK an alias for it. Likewise for
the other LCR register bits that are known with the CFCR prefix.
o Add MCR_IE and make MCR_IENABLE an alias for it.
o Add LSR_TEMT and make LSR_TSRE an alias for it.
o Add LSR_THRE and make LSR_TXRDY as alias for it.
o Add FCR_ENABLE and make FIFO_ENABLE as alias for it. Likewise for
the other FCR register bits that are known with the FIFO prefix.
o Add EFR_CTS and make EFR_AUTOCTS an alias for it.
o Add EFR_RTS and make EFR_AUTORTS an alias for it.

This is a first step in cleaning up the definitions in this file.

Remove advertising clause from University of California Regent's
license, per letter dated July 22, 1999 and email from Peter Wemm,
Alan Cox and Robert Watson.

Approved by: core, peter, alc, rwatson

Add a header for the i8259A register definitions. This is based on
additions to sys/amd64/isa/icu.h from PIIX4 and other datasheets. I
tweaked a few comments based on the NetBSD header of the same name when I
merged the constants to sys/i386/isa/icu.h, but the vast majority of this
file was created independently by Peter and not taken from any existing
files.

Submitted by: peter

Added definitions of most of the interesting 16950 register numbers
and some of their bits (i.e., fifo trigger levels, frequency multipliers
and divisors, and bits to select the registers for these). This
attempts to completely describe the 16950's complicated register selects
for 16950-specific registers only.

Added definitions for some 16650 features (mostly misfeatures). This
completes defining the 16650 register numbers but not all of their bits.

Fixed a minor error in the description of the EFR and a major error in
the description of the data latch registers (they were described as
readonly).

Added some better and worse aliases for standard registers, mostly taken
from the 16950 data sheet. Define deprecated aliases in terms of the
preferred one.

Don't define com_efr in terms of com_fifo. It is unrelated (in a
different bank).

Sorted register numbers together with the correspoding register bits.
Merged comments to match (put them at the right of the #defines instead
of duplicating them).

Sorted the resulting sections on UART type and register bank. Added a
comment for each bank.

Moved the definitions of the bits in the ns*50 registers from sioreg.h
to ns16550.h. The organization of these files was sort of backwards.
The bits in the registers have no driver or bus dependencies but they
but the offsets of the registers in bus space are very bus-dependent.
However, it does no harm to keep the definitions of the register offsets
in ns16550.h provided they are thought of as internal ns*50 offsets.

The uart(4) driver is an universal driver for various UART hardware.
It improves on sio(4) in the following areas:
o Fully newbusified to allow for memory mapped I/O. This is a must
for ia64 and sparc64,
o Machine dependent code to take full advantage of machine and firm-
ware specific ways to define serial consoles and/or debug ports.
o Hardware abstraction layer to allow the driver to be used with
various UARTs, such as the well-known ns8250 family of UARTs, the
Siemens sab82532 or the Zilog Z8530. This is especially important
for pc98 and sparc64 where it's common to have different UARTs,
o The notion of system devices to unkludge low-level consoles and
remote gdb ports and provides the mechanics necessary to support
the keyboard on sparc64 (which is UART based).
o The notion of a kernel interface so that a UART can be tied to
something other than the well-known TTY interface. This is needed
on sparc64 to present the user with a device and ioctl handling
suitable for a keyboard, but also allows us to cleanly hide an
UART when used as a debug port.

Following is a list of features and bugs/flaws specific to the ns8250
family of UARTs as compared to their support in sio(4):
o The uart(4) driver determines the FIFO size and automaticly takes
advantages of larger FIFOs and/or additional features. Note that
since I don't have sufficient access to 16[679]5x UARTs, hardware
flow control has not been enabled. This is almost trivial to do,
provided one can test. The downside of this is that broken UARTs
are more likely to not work correctly with uart(4). The need for
tunables or knobs may be large enough to warrant their creation.
o The uart(4) driver does not share the same bumpy history as sio(4)
and will therefore not provide the necessary hooks, tweaks, quirks
or work-arounds to deal with once common hardware. To that extend,
uart(4) supports a subset of the UARTs that sio(4) supports. The
question before us is whether the subset is sufficient for current
hardware.
o There is no support for multiport UARTs in uart(4). The decision
behind this is that uart(4) deals with one EIA RS232-C interface.
Packaging of multiple interfaces in a single chip or on a single
expansion board is beyond the scope of uart(4) and is now mostly
left for puc(4) to deal with. Lack of hardware made it impossible
to actually implement such a dependency other than is present for
the dual channel SAB82532 and Z8350 SCCs.

The current list of missing features is:
o No configuration capabilities. A set of tunables and sysctls is
being worked out. There are likely not going to be any or much
compile-time knobs. Such configuration does not fit well with
current hardware.
o No support for the PPS API. This is partly dependent on the
ability to configure uart(4) and partly dependent on having
sufficient information to implement it properly.

As usual, the manpage is present but lacks the attention the
software has gotten.

- Clean up function calling conventions.
- Be consistent about what we call our softc.
- Minor formatting.
- Add some register definitions gleaned from NetBSD/Linux.

Move the com_scr register address definition over with the other seven.

Approved by: bde

Oops, forgot to commit one file in the fd driver mega update. Here it
is, some more constants for NE765 & Co.

Pointed out by: silby, Dave Cornejo <dave@dogwood.com>

Moved the wd33c93 specific file to sys/dev/ic.

Move the files from i386/isa/ic/ to dev/ic/.

Added ESP98 specific register (merged from i386/isa/ic/esp.h).

Removed unneeded pc98 code (merged from i386/isa/ic/ns16550.h).

Add $FreeBSD$

$Id$ -> $FreeBSD$

Fixed 10 out of 40 lines of -Wcast-qual warnings/errors. 3 lines were
for old confusion of `volatile char *' with `volatile caddr_t'. 7 lines
were for not being careful about aligning pointers to volatiles.

Implemented sending of BREAKs. This is quite complicated because the
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.

Reminded by: PR 8318

Use [u]intptr_t instead of [unsigned] long to convert and/or represent
pointers.

This finishes fixing conversions between pointers and integers of
possibly different sizes in GENERIC.

Support compiling with `gcc -ansi'.

Enable the FIFO on enhanced floppy controllers. This reduces the
number of dma overruns/underruns for systems under heavy dma load.
As a side effect, broken enhanced floppy controllers that sometimes
don't detect dma overruns/underruns will give less errors.

Reviewed by: j@uriah.heep.sax.de (J Wunsch)

Back out part 1 of the MCFH that changed $Id$ to $FreeBSD$. We are not
ready for it yet.

Make the long-awaited change from $Id$ to $FreeBSD$

This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.

Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.

A #define really don't need a ; at the end.

Another round of merge/update.

(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike

Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>

Changes to the Digi/Arnet SYNC driver:

1. Create 2 x 8k transmit buffer blocks in place of the 16k block previously.
With this change the speed as tested with ttcp on a 2Mbit link went up
from 206kbyte/s to 236kbyte/s.
2. Change the rest of the functions to also have the definition of the
return value on a sepperate line.
3. Remove some unused variables.
4. Add code to recover from DMA underruns.
5. Reorder ar_get_packets() to handle errors better.
6. Only allocate a mbuf cluster if the data is more than the mbuf.

(and in a second diff in addition to the above)
7. Stops the occasional DMA underruns that occurred when 2 channels
are running at 2Mbit/s.

Submitted by: John Hay <jhay@mikom.csir.co.za>

Oops, this should have been committed with the other Hayes ESP changes.

This driver supports the Arnet SYNC/570i ISA cards that is based on the
HD64570 chip. Both the 2 and 4 port cards is supported and auto detected.

Line speeds of up to 2Mbps is possible. At this speed about 85% of the
bandwidth is usable with 486DX processors.

The standard FreeBSD sppp code is used for the link level layer. The
default protocol used is PPP. The Cisco HDLC protocol can be used by
adding "link2" to the ifconfig line in /etc/sysconfig or where ever
ifconfig is run.

At the moment only the V.35 and X.21 interfaces is supported. The others
may need tweaks to the clock selection code.

Submitted by: John Hay <jhay@mikom.csir.co.za>

Staticized an inline function. All inlines in kernel headers should be
static. The function shouldn't be here anyway. It is driver dependent,
while `ic' files are supposed to only depend on the IC.

Cleanup, make things static.

Rewrite:
- use pseudo-dma
- provide the same features and interface as sio
- support multiple boards
- fix bugs.

Some compile-time configuration constants are set to support higher
speeds and Cyclom-16Y's at a 30% relative cost in efficiency.
Cyclom-16Y support is untested.

Next version, many bugs fixed

Remove trailing whitespace.

RISCom/8 driver

Add the Cyclades serial driver code (ALPHA) from Andrew Werple and
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD

Peter's work to work around one of the most annoying bugs in the
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.

Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.

Submitted by: (mostly) Peter Dufault <dufault@FreeBSD.org>

DMA automode patch, fix SB16 clicks
Submitted by: tim@cs.city.ac.uk

Updated driver to the 1.1.5 version:

date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.

New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track

Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now

Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()

Reviewed by:
Submitted by:
Obtained from:

Removed all patch kit headers, sccsid and rcsid strings, put $Id$ in, some
minor cleanup. Added $Id$ to files that did not have any version info, etc

i82586 support file for Garrett Wollmans ie driver

This commit was generated by cvs2svn to compensate for changes in r4,
which included commits to RCS files with non-trunk default branches.