Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

ath(4): begin fleshing out a "reset type" extension to force cold/warn resets.

Right now the only way to force a cold reset is:

* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.

Trouble is, cold resets take quite a bit longer than warm resets.

However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.

The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.

This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.

It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.

To make this possible:

* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.

This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.

Tested:

* AR9380 (STA)
* AR9485 CUS198 (STA)

Obtained from: Qualcomm Atheros, Linux ath9k

Migrate the chip power mode status to public ath_hal, rather than the
private per-chip HAL.

This allows the ah_osdep.[ch] code to check whether the power state is
valid for doing chip programming.

It should be a no-op for normal driver work but it does require a
clean kernel/module rebuild, as the size of HAL structures have changed.

Now, this doesn't track whether the hardware is ACTUALLY awake,
as NETWORK_SLEEP wakes the chip up for a short period when traffic
is received. This doesn't actually set the power mode to AWAKE, so
we have to be careful about how we touch things.

But it's enough to start down the path of implementing station mode
chipset power savings, as a large part of the silliness is making
sure the chip is awake during periodic calibration / ANI and
random places where transmit may be occuring. I'd rather not a repeat
of debugging power save on ath9k, where races with calibration
and transmit path stuff took a couple years to shake out.

Tested:

* AR5416, STA mode

Stop using the hardware register value byte order swapping for now,
at least until I can root cause what's going on.

The only platform I've seen this on is the AR9220 when attached to
the AR71xx CPUs. I get immediate PCIe bus errors and all subsequent
accesses cause further MIPS bus exceptions. I don't have any other
big-endian platforms to test this on.

If I get a chance (or two), I'll try to whack this on a bus analyser
and see exactly what happens.

I'd rather leave this on, especially for slower, embedded platforms.
But the #ifdef hell is something I'm trying to avoid.

Fix a corner case in the HAL debugging changes, where ah was NULL.

Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.

* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed

This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.

Re-introduce a global ath_hal_debug again for now, whilst I figure out what
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)

The global ath_hal_debug now affects all instances of the HAL.

This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.

Include the initial support for external EEPROMs.

The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.

I believe earlier parts can do something similar but I haven't
experienced it first-hand.

This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.

Replace Id keyword with FreeBSD keyword and set the svn props correctly.
No functional change.

5416 and later parts mux the gpio outputs; extend the api to include
a signal type that's used to select the appropriate mux

Recognize AR5212_AR2317_REV2 in ar5312Probe()

Submitted by: Pavel Roskin <proski@gnu.org>

Overhaul regulatory support:
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>

Sponsored by: Carlson Wireless

fix return status handling by ar5XXXReset; this is the reason the
driver sometimes reports reset failed w/ status 0

add FreeBSD property

fix ini setup

Submitted by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>

remove duplicate case

Obtained from: netbsd

remove conflicting decl

Obtained from: netbsd

import ath hal

add chip+rf names for debug msgs, showing compiled-in support, etc.

Replace most compile-time support options with linker sets for
chip and RF backend support:
o add OS_DATA_SET and OS_SET_DECLARE os requirements for setting
up linker sets
o add AH_CHIP macro for registering chip support (e.g. 5210)
o add AH_RF macro for registering RF support (e.g. 2413); note
this isn't required for single chip solutions where there's no
ambiguity (e.g. 5416/9160+2133) but for 5212 class parts it's
required because of the multi-chip solutions
o remove all uses of AH_SUPPORT_AR5210, AH_SUPPORT_AR5211, AH_SUPPORT_5212,
and AH_SUPPORT_AR9160; still need AH_SUPPORT_AR5416 to enable the 11n
descriptor formats and 5312 support is presently broken
o remove all uses of AH_SUPPORT_2133, AH_SUPPORT_2413, AH_SUPPORT_5111,
AH_SUPPORT_5112, AH_SUPPORT_2417, AH_SUPPORT_2425, and AH_SUPPORT_5413;
5312-related support still requires fixup

Remaining issues:
o fixup SoC attach
o ath_hal_attach uses a hack to probe w/o access to the vendorid
o fallback handling of parts w/o a macrev needs to be restored

Update to later code from my repository:
o many bug fixes
o add new periodic calibration api
o break up 5416 periodic calibration code in preparation for 928x
o move get noise floor to rf backends
o 5416-specific ani (still disabled)
o modularize 5210 eeprom format a la other eeprom formats
o start cleaning up regdomain code
o prepare for proper 1/2 and 1/4 width channel support
o bring back 900MHz card support
o clean up 5212 rf version handling
o add 1/2 and 1/4 width channel support for 5212 parts
o split 5212 rfgain handling out
o improve ani debugging
o add AH_USE_INIPDGAIN compile option
o purge a bunch of dead 5212 state
o add 1/2 and 1/4 rate modes
o remove HAL_CAP_CHAN_HALFRATE and HAL_CAP_CHAN_QUARTERRATE; the
same info can now be deduced from the set of supported modes

virgin import of ath hal