1#
2# Specific board setup for the Atheros AP96 reference board.
3#
4# The AP96 has the following hardware:
5#
6# + AR7161 CPU SoC
7# + AR9223 2.4GHz 11n
8# + AR9220 5GHz 11n
9# + AR8316 10/100/1000 switch
10# + m25p64 based 8MB flash
11# + 64mb RAM
12# + uboot environment
13
| 1#
2# Specific board setup for the Atheros AP96 reference board.
3#
4# The AP96 has the following hardware:
5#
6# + AR7161 CPU SoC
7# + AR9223 2.4GHz 11n
8# + AR9220 5GHz 11n
9# + AR8316 10/100/1000 switch
10# + m25p64 based 8MB flash
11# + 64mb RAM
12# + uboot environment
13
|
14# $FreeBSD: head/sys/mips/conf/AP96 291049 2015-11-19 01:58:12Z imp $
| 14# $FreeBSD: head/sys/mips/conf/AP96 295945 2016-02-24 00:39:36Z sobomax $
|
15
16#NO_UNIVERSE
17
18include "AR71XX_BASE"
19ident "AP96"
20hints "AP96.hints"
21
22options AR71XX_REALMEM=64*1024*1024
23
24options AR71XX_ENV_UBOOT
25
26# For DOS - enable if required
27options MSDOSFS
28
29# uncompress - to boot read-only lzma natively from flash
| 15
16#NO_UNIVERSE
17
18include "AR71XX_BASE"
19ident "AP96"
20hints "AP96.hints"
21
22options AR71XX_REALMEM=64*1024*1024
23
24options AR71XX_ENV_UBOOT
25
26# For DOS - enable if required
27options MSDOSFS
28
29# uncompress - to boot read-only lzma natively from flash
|
30device geom_uncompress
31options GEOM_UNCOMPRESS
32options ROOTDEVNAME=\"ufs:/dev/map/rootfs.uncompress\"
| 30device geom_uzip
31options GEOM_UZIP
32options ROOTDEVNAME=\"ufs:/dev/map/rootfs.uzip\"
|
33
34# Used for the static uboot partition map
35device geom_map
36
37# Options needed for the EEPROM based calibration/PCI configuration data.
38options AR71XX_ATH_EEPROM # Fetch EEPROM/PCI config from flash
39options ATH_EEPROM_FIRMWARE # Use EEPROM from flash
40device firmware # Used by the above
41
42# Options required for miiproxy and mdiobus
43options ARGE_MDIO # Export an MDIO bus separate from arge
44device miiproxy # MDIO bus <-> MII PHY rendezvous
45
46device etherswitch
47device arswitch
| 33
34# Used for the static uboot partition map
35device geom_map
36
37# Options needed for the EEPROM based calibration/PCI configuration data.
38options AR71XX_ATH_EEPROM # Fetch EEPROM/PCI config from flash
39options ATH_EEPROM_FIRMWARE # Use EEPROM from flash
40device firmware # Used by the above
41
42# Options required for miiproxy and mdiobus
43options ARGE_MDIO # Export an MDIO bus separate from arge
44device miiproxy # MDIO bus <-> MII PHY rendezvous
45
46device etherswitch
47device arswitch
|