6# 7# NB: You probably don't want to try running a kernel built from this 8# file. Instead, you should start from GENERIC, and add options from 9# this file as required. 10# 11 12# 13# This directive is mandatory; it defines the architecture to be 14# configured for; in this case, the 386 family based IBM-PC and 15# compatibles. 16# 17machine "i386" 18 19# 20# This is the ``identification'' of the kernel. Usually this should 21# be the same as the name of your kernel. 22# 23ident LINT 24 25# 26# The `maxusers' parameter controls the static sizing of a number of 27# internal system tables by a complicated formula defined in param.c. 28# 29maxusers 10 30 31# 32# Certain applications can grow to be larger than the 128M limit 33# that FreeBSD initially imposes. Below are some options to 34# allow that limit to grow to 256MB, and can be increased further 35# with changing the parameters. MAXDSIZ is the maximum that the 36# limit can be set to, and the DFLDSIZ is the default value for 37# the limit. You might want to set the default lower than the 38# max, and explicitly set the maximum with a shell command for processes 39# that regularly exceed the limit like INND. 40# 41options "MAXDSIZ=(256*1024*1024)" 42options "DFLDSIZ=(256*1024*1024)" 43 44# When this is set, be extra conservative in various parts of the kernel 45# and choose functionality over speed (on the widest variety of systems). 46options FAILSAFE 47 48# Options for the VM subsystem 49#options PQ_NOOPT # No coloring 50options PQ_LARGECACHE # color for 512k/16k cache 51#options PQ_HUGECACHE # color for 1024k/16k cache 52 53# This allows you to actually store this configuration file into 54# the kernel binary itself, where it may be later read by saying: 55# strings -aout -n 3 /kernel | grep ^___ | sed -e 's/^___//' > MYKERNEL 56# 57options INCLUDE_CONFIG_FILE # Include this file in kernel 58 59# 60# This directive defines a number of things: 61# - The compiled kernel is to be called `kernel' 62# - The root filesystem might be on partition wd0a 63# - Crash dumps will be written to wd0b, if possible. Specifying the 64# dump device here is not recommended. Use dumpon(8). 65# 66config kernel root on wd0 dumps on wd0 67 68 69##################################################################### 70# SMP OPTIONS: 71# 72# SMP enables building of a Symmetric MultiProcessor Kernel. 73# APIC_IO enables the use of the IO APIC for Symmetric I/O. 74# NCPU sets the number of CPUs, defaults to 2. 75# NBUS sets the number of busses, defaults to 4. 76# NAPIC sets the number of IO APICs on the motherboard, defaults to 1. 77# NINTR sets the total number of INTs provided by the motherboard. 78# 79# Notes: 80# 81# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard. 82# 83# Be sure to disable 'cpu "I386_CPU"' && 'cpu "I486_CPU"' for SMP kernels. 84# 85# Check the 'Rogue SMP hardware' section to see if additional options 86# are required by your hardware. 87# 88 89# Mandatory: 90options SMP # Symmetric MultiProcessor Kernel 91options APIC_IO # Symmetric (APIC) I/O 92 93# Optional, these are the defaults plus 1: 94options NCPU=5 # number of CPUs 95options NBUS=5 # number of busses 96options NAPIC=2 # number of IO APICs 97options NINTR=25 # number of INTs 98 99# 100# Rogue SMP hardware: 101# 102 103# Bridged PCI cards: 104# 105# The MP tables of most of the current generation MP motherboards 106# do NOT properly support bridged PCI cards. To use one of these 107# cards you should refer to ??? 108 109 110##################################################################### 111# CPU OPTIONS 112 113# 114# You must specify at least one CPU (the one you intend to run on); 115# deleting the specification for CPUs you don't need to use may make 116# parts of the system run faster. This is especially true removing 117# I386_CPU. 118# 119cpu "I386_CPU" 120cpu "I486_CPU" 121cpu "I586_CPU" # aka Pentium(tm) 122cpu "I686_CPU" # aka Pentium Pro(tm) 123 124# 125# Options for CPU features. 126# 127# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM 128# BlueLightning CPU. It works only with Cyrix FPU, and this option 129# should not be used with Intel FPU. 130# 131# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning 132# CPU if CPU supports it. The default is double-clock mode on 133# BlueLightning CPU box. 134# 135# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1). 136# 137# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct 138# mapped mode. Default is 2-way set associative mode. 139# 140# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space 141# of Cyrix 6x86 and 6x86MX CPUs. If this option is not set and 142# FAILESAFE is defined, NO_LOCK bit of CCR1 is cleared. (NOTE 3) 143# 144# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables 145# reorder). This option should not be used if you use memory mapped 146# I/O device(s). 147# 148# CPU_FASTER_5X86_FPU enables faster FPU exception handler. 149# 150# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products 151# for i386 machines. 152# 153# CPU_IORT defines I/O clock delay time (NOTE 1). Default vaules of 154# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively 155# (no clock delay). 156# 157# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination 158# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE 159# 1). 160# 161# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1). 162# 163# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU 164# enters suspend mode following execution of HALT instruction. 165# 166# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD 167# K5/K6/K6-2 cpus. 168# 169# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache 170# flush at hold state. 171# 172# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs 173# without cache flush at hold state, and (2) write-back CPU cache on 174# Cyrix 6x86 whose revision < 2.7 (NOTE 2). 175# 176# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY 177# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is 178# executed. This should be included for ALL kernels that won't run 179# on a Pentium. 180# 181# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors 182# which indicates that the 15-16MB range is *definitely* not being 183# occupied by an ISA memory hole. 184# 185# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT, 186# CPU_LOOP_ENand CPU_RSTK_EN should not be used becasue of CPU bugs. 187# These options may crash your system. 188# 189# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled 190# in write-through mode when revision < 2.7. If revision of Cyrix 191# 6x86 >= 2.7, CPU cache is always enabled in write-back mode. 192# 193# NOTE 3: This option may cause failures for software that requires 194# locked cycles in order to operate correctly. 195# 196options "CPU_BLUELIGHTNING_FPU_OP_CACHE" 197options "CPU_BLUELIGHTNING_3X" 198options "CPU_BTB_EN" 199options "CPU_DIRECT_MAPPED_CACHE" 200options "CPU_DISABLE_5X86_LSSER" 201options "CPU_FASTER_5X86_FPU" 202options "CPU_I486_ON_386" 203options "CPU_IORT" 204options "CPU_LOOP_EN" 205options "CPU_RSTK_EN" 206options "CPU_SUSP_HLT" 207options "CPU_WT_ALLOC" 208options "CYRIX_CACHE_WORKS" 209options "CYRIX_CACHE_REALLY_WORKS" 210#options "NO_F00F_HACK" 211 212# 213# A math emulator is mandatory if you wish to run on hardware which 214# does not have a floating-point processor. Pick either the original, 215# bogus (but freely-distributable) math emulator, or a much more 216# fully-featured but GPL-licensed emulator taken from Linux. 217# 218options MATH_EMULATE #Support for x87 emulation 219# Don't enable both of these in a real config. 220options GPL_MATH_EMULATE #Support for x87 emulation via 221 #new math emulator 222 223 224##################################################################### 225# COMPATIBILITY OPTIONS 226 227# 228# Implement system calls compatible with 4.3BSD and older versions of 229# FreeBSD. You probably do NOT want to remove this as much current code 230# still relies on the 4.3 emulation. 231# 232options "COMPAT_43" 233 234# 235# Statically compile in the i386 a.out LKM compatability support. 236# Also available as an KLD module. 237# 238options LKM 239 240# 241# Allow user-mode programs to manipulate their local descriptor tables. 242# This option is required for the WINE Windows(tm) emulator, and is 243# not used by anything else (that we know of). 244# 245options USER_LDT #allow user-level control of i386 ldt 246 247# 248# These three options provide support for System V Interface 249# Definition-style interprocess communication, in the form of shared 250# memory, semaphores, and message queues, respectively. 251# 252options SYSVSHM 253options SYSVSEM 254options SYSVMSG 255 256# 257# This option includes a MD5 routine in the kernel, this is used for 258# various authentication and privacy uses. 259# 260options "MD5" 261 262# 263# Allow processes to switch to vm86 mode, as well as enabling direct 264# user-mode access to the I/O port space. This option is necessary for 265# the doscmd emulator to run. 266# 267options "VM86" 268 269 270##################################################################### 271# DEBUGGING OPTIONS 272 273# 274# Enable the kernel debugger. 275# 276options DDB 277 278# 279# Don't drop into DDB for a panic. Intended for unattended operation 280# where you may want to drop to DDB from the console, but still want 281# the machine to recover from a panic 282# 283options DDB_UNATTENDED 284 285# 286# If using GDB remote mode to debug the kernel, there's a non-standard 287# extension to the remote protocol that can be used to use the serial 288# port as both the debugging port and the system console. It's non- 289# standard and you're on your own if you enable it. See also the 290# "remotechat" variables in the FreeBSD specific version of gdb. 291# 292options GDB_REMOTE_CHAT 293 294# 295# KTRACE enables the system-call tracing facility ktrace(2). 296# 297options KTRACE #kernel tracing 298 299# 300# The INVARIANTS option is used in a number of source files to enable 301# extra sanity checking of internal structures. This support is not 302# enabled by default because of the extra time it would take to check 303# for these conditions, which can only occur as a result of 304# programming errors. 305# 306options INVARIANTS 307 308# 309# The INVARIANT_SUPPORT option makes us compile in support for 310# verifying some of the internal structures. It is a prerequisite for 311# 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be 312# called. The intent is that you can set 'INVARIANTS' for single 313# source files (by changing the source file or specifying it on the 314# command line) if you have 'INVARIANT_SUPPORT' enabled. 315# 316options INVARIANT_SUPPORT 317 318# 319# The DIAGNOSTIC option is used to enable extra debugging information 320# from some parts of the kernel. As this makes everything more noisy, 321# it is disabled by default. 322# 323options DIAGNOSTIC 324 325# 326# PERFMON causes the driver for Pentium/Pentium Pro performance counters 327# to be compiled. See perfmon(4) for more information. 328# 329options PERFMON 330 331 332# 333# This option let some drivers co-exist that can't co-exist in a running 334# system. This is used to be able to compile all kernel code in one go for 335# quality assurance purposes (like this file, which the option takes it name 336# from.) 337# 338options COMPILING_LINT 339 340 341# XXX - this doesn't belong here. 342# Allow ordinary users to take the console - this is useful for X. 343options UCONSOLE 344 345# XXX - this doesn't belong here either 346options USERCONFIG #boot -c editor 347options INTRO_USERCONFIG #imply -c and show intro screen 348options VISUAL_USERCONFIG #visual boot -c editor 349 350##################################################################### 351# NETWORKING OPTIONS 352 353# 354# Protocol families: 355# Only the INET (Internet) family is officially supported in FreeBSD. 356# Source code for the NS (Xerox Network Service) is provided for amusement 357# value. 358# 359options INET #Internet communications protocols 360 361options IPX #IPX/SPX communications protocols 362options IPXIP #IPX in IP encapsulation (not available) 363options IPTUNNEL #IP in IPX encapsulation (not available) 364 365options NETATALK #Appletalk communications protocols 366 367# These are currently broken but are shipped due to interest. 368#options NS #Xerox NS protocols 369 370# These are currently broken and are no longer shipped due to lack 371# of interest. 372#options CCITT #X.25 network layer 373#options ISO 374#options TPIP #ISO TP class 4 over IP 375#options TPCONS #ISO TP class 0 over X.25 376#options LLC #X.25 link layer for Ethernets 377#options HDLC #X.25 link layer for serial lines 378#options EON #ISO CLNP over IP 379#options NSIP #XNS over IP 380 381# 382# Network interfaces: 383# The `loop' pseudo-device is MANDATORY when networking is enabled. 384# The `ether' pseudo-device provides generic code to handle 385# Ethernets; it is MANDATORY when a Ethernet device driver is 386# configured or token-ring is enabled. 387# The 'fddi' pseudo-device provides generic code to support FDDI. 388# The `sppp' pseudo-device serves a similar role for certain types 389# of synchronous PPP links (like `cx', `ar'). 390# The `sl' pseudo-device implements the Serial Line IP (SLIP) service. 391# The `ppp' pseudo-device implements the Point-to-Point Protocol. 392# The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be 393# aware of the legal and administrative consequences of enabling this 394# option. The number of devices determines the maximum number of 395# simultaneous BPF clients programs runnable. 396# The `disc' pseudo-device implements a minimal network interface, 397# which throws away all packets sent and never receives any. It is 398# included for testing purposes. 399# The `tun' pseudo-device implements the User Process PPP (iijppp) 400# The `streams' pseudo-device implements SysVR4 STREAMS emulation. 401# 402# The PPP_BSDCOMP option enables support for compress(1) style entire 403# packet compression, the PPP_DEFLATE is for zlib/gzip style compression. 404# PPP_FILTER enables code for filtering the ppp data stream and selecting 405# events for resetting the demand dial activity timer - requires bpfilter. 406# See pppd(8) for more details. 407# 408pseudo-device ether #Generic Ethernet 409pseudo-device token #Generic TokenRing 410pseudo-device fddi #Generic FDDI 411pseudo-device sppp #Generic Synchronous PPP 412pseudo-device loop #Network loopback device 413pseudo-device bpfilter 4 #Berkeley packet filter 414pseudo-device disc #Discard device 415pseudo-device tun 1 #Tunnel driver (user process ppp(8)) 416pseudo-device sl 2 #Serial Line IP 417pseudo-device ppp 2 #Point-to-point protocol 418pseudo-device streams 419options PPP_BSDCOMP #PPP BSD-compress support 420options PPP_DEFLATE #PPP zlib/deflate/gzip support 421options PPP_FILTER #enable bpf filtering (needs bpfilter) 422 423# 424# Internet family options: 425# 426# TCP_COMPAT_42 causes the TCP code to emulate certain bugs present in 427# 4.2BSD. This option should not be used unless you have a 4.2BSD 428# machine and TCP connections fail. 429# 430# MROUTING enables the kernel multicast packet forwarder, which works 431# with mrouted(8). 432# 433# IPFIREWALL enables support for IP firewall construction, in 434# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends 435# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT 436# limits the number of times a matching entry can be logged. 437# 438# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any" 439# and if you do not add other rules during startup to allow access, 440# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall=open 441# in /etc/rc.conf when first enabling this feature, then refining the 442# firewall rules in /etc/rc.firewall after you've tested that the new kernel 443# feature works properly. 444# 445# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to 446# allow everything. Use with care, if a cracker can crash your 447# firewall machine, they can get to your protected machines. However, 448# if you are using it as an as-needed filter for specific problems as 449# they arise, then this may be for you. Changing the default to 'allow' 450# means that you won't get stuck if the kernel and /sbin/ipfw binary get 451# out of sync. 452# 453# IPDIVERT enables the divert IP sockets, used by ``ipfw divert'' 454# 455# IPFILTER enables Darren Reed's ipfilter package. 456# IPFILTER_LOG enables ipfilter's logging. 457# IPFILTER_LKM enables LKM support for an ipfilter module (untested). 458# 459# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding 460# packets without touching the ttl). This can be useful to hide firewalls 461# from traceroute and similar tools. 462# 463# TCPDEBUG is undocumented. 464# 465options "TCP_COMPAT_42" #emulate 4.2BSD TCP bugs 466options MROUTING # Multicast routing 467options IPFIREWALL #firewall 468options IPFIREWALL_VERBOSE #print information about 469 # dropped packets 470options IPFIREWALL_FORWARD #enable transparent proxy support 471options "IPFIREWALL_VERBOSE_LIMIT=100" #limit verbosity 472options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default 473options IPDIVERT #divert sockets 474options IPFILTER #kernel ipfilter support 475options IPFILTER_LOG #ipfilter logging 476#options IPFILTER_LKM #kernel support for ip_fil.o LKM 477options IPSTEALTH #support for stealth forwarding 478options TCPDEBUG 479 480# ICMP_BANDLIM enables icmp error response bandwidth limiting. You 481# typically want this option as it will help protect the machine from 482# D.O.S. packet attacks. 483# 484options "ICMP_BANDLIM" 485 486# DUMMYNET enables the "dummynet" bandwidth limiter. You need 487# IPFIREWALL as well. See the dummynet(4) manpage for more info. 488# BRIDGE enables bridging between ethernet cards -- see bridge(4). 489# You can use IPFIREWALL and dummynet together with bridging. 490options DUMMYNET 491options BRIDGE 492 493# 494# ATM (HARP version) options 495# 496# ATM_CORE includes the base ATM functionality code. This must be included 497# for ATM support. 498# 499# ATM_IP includes support for running IP over ATM. 500# 501# At least one (and usually only one) of the following signalling managers 502# must be included (note that all signalling managers include PVC support): 503# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'. 504# ATM_SPANS includes support for the `spans' signalling manager, which runs 505# the FORE Systems's proprietary SPANS signalling protocol. 506# ATM_UNI includes support for the `uni30' and `uni31' signalling managers, 507# which run the ATM Forum UNI 3.x signalling protocols. 508# 509# The `hea' driver provides support for the Efficient Networks, Inc. 510# ENI-155p ATM PCI Adapter. 511# 512# The `hfa' driver provides support for the FORE Systems, Inc. 513# PCA-200E ATM PCI Adapter. 514# 515options ATM_CORE #core ATM protocol family 516options ATM_IP #IP over ATM support 517options ATM_SIGPVC #SIGPVC signalling manager 518options ATM_SPANS #SPANS signalling manager 519options ATM_UNI #UNI signalling manager 520device hea0 #Efficient ENI-155p ATM PCI 521device hfa0 #FORE PCA-200E ATM PCI 522 523 524##################################################################### 525# FILESYSTEM OPTIONS 526 527# 528# Only the root, /usr, and /tmp filesystems need be statically 529# compiled; everything else will be automatically loaded at mount 530# time. (Exception: the UFS family---FFS, and MFS --- cannot 531# currently be demand-loaded.) Some people still prefer to statically 532# compile other filesystems as well. 533# 534# NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be 535# buggy, and WILL panic your system if you attempt to do anything with 536# them. They are included here as an incentive for some enterprising 537# soul to sit down and fix them. 538# 539 540# One of these is mandatory: 541options FFS #Fast filesystem 542options MFS #Memory File System 543options NFS #Network File System 544 545# The rest are optional: 546# options NFS_NOSERVER #Disable the NFS-server code. 547options "CD9660" #ISO 9660 filesystem 548options FDESC #File descriptor filesystem 549options KERNFS #Kernel filesystem 550options MSDOSFS #MS DOS File System 551options NTFS #NT File System 552options NULLFS #NULL filesystem 553options PORTAL #Portal filesystem 554options PROCFS #Process filesystem 555options UMAPFS #UID map filesystem 556options UNION #Union filesystem 557# The xFS_ROOT options REQUIRE the associated ``options xFS'' 558options "CD9660_ROOT" #CD-ROM usable as root device 559options FFS_ROOT #FFS usable as root device 560options MFS_ROOT #MFS usable as root device 561options NFS_ROOT #NFS usable as root device 562# This code is still experimental (e.g. doesn't handle disk slices well). 563# Also, 'options MFS' is currently incompatible with DEVFS. 564options DEVFS #devices filesystem 565 566# Soft updates is technique for improving file system speed and 567# making abrupt shutdown less risky. It is not enabled by default due 568# to copyright restraints on the code that implement it. 569# 570# Read ../../ufs/ffs/README.softupdates to learn what you need to 571# do to enable this. ../../../contrib/sys/softupdates/README gives 572# more details on how they actually work. 573# 574#options SOFTUPDATES 575 576# Make space in the kernel for a MFS root filesystem. Define to the number 577# of kilobytes to reserve for the filesystem. 578options MFS_ROOT_SIZE=10 579# Allows MFS filesystems to be exported via nfs 580options EXPORTMFS 581 582# Allow this many swap-devices. 583options NSWAPDEV=20 584 585# Disk quotas are supported when this option is enabled. 586options QUOTA #enable disk quotas 587 588# Add more checking code to various filesystems 589#options NULLFS_DIAGNOSTIC 590#options KERNFS_DIAGNOSTIC 591#options UMAPFS_DIAGNOSTIC 592#options UNION_DIAGNOSTIC 593 594# In particular multi-session CD-Rs might require a huge amount of 595# time in order to "settle". If we are about mounting them as the 596# root f/s, we gotta wait a little. 597# 598# The number is supposed to be in seconds. 599options "CD9660_ROOTDELAY=20" 600 601# If you are running a machine just as a fileserver for PC and MAC 602# users, using SAMBA or Netatalk, you may consider setting this option 603# and keeping all those users' directories on a filesystem that is 604# mounted with the suiddir option. This gives new files the same 605# ownership as the directory (similiar to group). It's a security hole 606# if you let these users run programs, so confine it to file-servers 607# (but it'll save you lots of headaches in those cases). Root owned 608# directories are exempt and X bits are cleared. The suid bit must be 609# set on the directory as well; see chmod(1) PC owners can't see/set 610# ownerships so they keep getting their toes trodden on. This saves 611# you all the support calls as the filesystem it's used on will act as 612# they expect: "It's my dir so it must be my file". 613# 614options SUIDDIR 615 616 617# Add some error checking code to the null_bypass routine 618# in the NULL filesystem 619#options SAFETY 620 621 622# NFS options: 623options "NFS_MINATTRTIMO=3" # VREG attrib cache timeout in sec 624options "NFS_MAXATTRTIMO=60" 625options "NFS_MINDIRATTRTIMO=30" # VDIR attrib cache timeout in sec 626options "NFS_MAXDIRATTRTIMO=60" 627options "NFS_GATHERDELAY=10" # Default write gather delay (msec) 628options "NFS_UIDHASHSIZ=29" # Tune the size of nfssvc_sock with this 629options "NFS_WDELAYHASHSIZ=16" # and with this 630options "NFS_MUIDHASHSIZ=63" # Tune the size of nfsmount with this 631options NFS_DEBUG # Enable NFS Debugging 632 633# Coda stuff: 634options CODA #CODA filesystem. 635pseudo-device vcoda 4 #coda minicache <-> venus comm. 636 637# 638# Add support for the EXT2FS filesystem of Linux fame. Be a bit 639# careful with this - the ext2fs code has a tendency to lag behind 640# changes and not be exercised very much, so mounting read/write could 641# be dangerous (and even mounting read only could result in panics.) 642# 643options "EXT2FS" 644 645 646 647##################################################################### 648# POSIX P1003.1B 649 650# Real time extensions added int the 1993 Posix 651# P1003_1B: Infrastructure 652# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING 653# _KPOSIX_VERSION: Version kernel is built for 654 655options "P1003_1B" 656options "_KPOSIX_PRIORITY_SCHEDULING" 657options "_KPOSIX_VERSION=199309L" 658 659 660##################################################################### 661# SCSI DEVICES 662 663# SCSI DEVICE CONFIGURATION 664 665# The SCSI subsystem consists of the `base' SCSI code, a number of 666# high-level SCSI device `type' drivers, and the low-level host-adapter 667# device drivers. The host adapters are listed in the ISA and PCI 668# device configuration sections below. 669# 670# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so 671# that a given bus, target, and LUN always come on line as the same 672# device unit. In earlier versions the unit numbers were assigned 673# in the order that the devices were probed on the SCSI bus. This 674# means that if you removed a disk drive, you may have had to rewrite 675# your /etc/fstab file, and also that you had to be careful when adding 676# a new disk as it may have been probed earlier and moved your device 677# configuration around. 678 679# This old behavior is maintained as the default behavior. The unit 680# assignment begins with the first non-wired down unit for a device 681# type. For example, if you wire a disk as "da3" then the first 682# non-wired disk will be assigned da4. 683 684# The syntax for wiring down devices is: 685 686# controller scbus0 at ahc0 # Single bus device 687# controller scbus1 at ahc1 bus 0 # Single bus device 688# controller scbus3 at ahc2 bus 0 # Twin bus device 689# controller scbus2 at ahc2 bus 1 # Twin bus device 690# disk da0 at scbus0 target 0 unit 0 691# disk da1 at scbus3 target 1 692# disk da2 at scbus2 target 3 693# tape st1 at scbus1 target 6 694# device cd0 at scbus? 695 696# "units" (SCSI logical unit number) that are not specified are 697# treated as if specified as LUN 0. 698 699# All SCSI devices allocate as many units as are required. 700 701# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI 702# configuration and doesn't have to be explicitly configured. 703 704controller scbus0 #base SCSI code 705device ch0 #SCSI media changers 706device da0 #SCSI direct access devices (aka disks) 707device sa0 #SCSI tapes 708device cd0 #SCSI CD-ROMs 709#device od0 #SCSI optical disk 710device pass0 #CAM passthrough driver 711 712# The previous devices (ch, da, st, cd) are recognized by config. 713# config doesn't (and shouldn't) know about these newer ones, 714# so we have to specify that they are on a SCSI bus with the "at scbus?" 715# clause. 716 717device pt0 at scbus? # SCSI processor type 718device sctarg0 at scbus? # SCSI target 719 720# CAM OPTIONS: 721# debugging options: 722# -- NOTE -- If you specify one of the bus/target/lun options, you must 723# specify them all! 724# CAMDEBUG: When defined enables debugging macros 725# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses. 726# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets. 727# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns. 728# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE, 729# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB 730# 731# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds 732# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions 733# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions 734# SCSI_REPORT_GEOMETRY: Always report disk geometry at boot up instead 735# of only when booting verbosely. 736# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter) 737# queue after a bus reset, and the number of milliseconds to 738# freeze the device queue after a bus device reset. 739options CAMDEBUG 740options "CAM_DEBUG_BUS=-1" 741options "CAM_DEBUG_TARGET=-1" 742options "CAM_DEBUG_LUN=-1" 743options "CAM_DEBUG_FLAGS=CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" 744options "CAM_MAX_HIGHPOWER=4" 745options SCSI_NO_SENSE_STRINGS 746options SCSI_NO_OP_STRINGS 747options SCSI_REPORT_GEOMETRY 748options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device 749 750# Options for the CAM CDROM driver: 751# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN 752# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only 753# enforced if there is I/O waiting for another LUN 754# The compiled in defaults for these variables are 2 and 10 seconds, 755# respectively. 756# 757# These can also be changed on the fly with the following sysctl variables: 758# kern.cam.cd.changer.min_busy_seconds 759# kern.cam.cd.changer.max_busy_seconds 760# 761options "CHANGER_MIN_BUSY_SECONDS=2" 762options "CHANGER_MAX_BUSY_SECONDS=10" 763 764# Options for the CAM sequential access driver: 765# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes 766# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes 767# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes 768options "SA_SPACE_TIMEOUT=(60)" 769options "SA_REWIND_TIMEOUT=(2*60)" 770options "SA_ERASE_TIMEOUT=(4*60)" 771 772 773##################################################################### 774# MISCELLANEOUS DEVICES AND OPTIONS 775 776# The `pty' device usually turns out to be ``effectively mandatory'', 777# as it is required for `telnetd', `rlogind', `screen', `emacs', and 778# `xterm', among others. 779 780pseudo-device pty 16 #Pseudo ttys - can go as high as 256 781pseudo-device speaker #Play IBM BASIC-style noises out your speaker 782pseudo-device gzip #Exec gzipped a.out's 783pseudo-device vn #Vnode driver (turns a file into a device) 784pseudo-device snp 3 #Snoop device - to look at pty/vty/etc.. 785pseudo-device ccd 4 #Concatenated disk driver 786 787# Configuring Vinum into the kernel is not necessary, since the kld 788# module gets started automatically when vinum(8) starts. This 789# device is also untested. Use at your own risk. 790# 791# The option VINUMDEBUG must match the value set in CFLAGS 792# in /usr/src/sbin/vinum/Makefile. Failure to do so will result in 793# the following message from vinum(8): 794# 795# Can't get vinum config: Invalid argument 796# 797# see vinum(4) for more reasons not to use these options. 798pseudo-device vinum #Vinum concat/mirror/raid driver 799options VINUMDEBUG #enable Vinum debugging hooks 800 801# These are only for watching for bitrot in old tty code. 802# broken 803#pseudo-device tb 804 805# Size of the kernel message buffer. Should be N * pagesize. 806options "MSGBUF_SIZE=40960" 807 808 809##################################################################### 810# HARDWARE DEVICE CONFIGURATION 811 812# ISA and EISA devices: 813# EISA support is available for some device, so they can be auto-probed. 814# Micro Channel is not supported at all. 815 816# 817# Mandatory ISA devices: isa, npx 818# 819controller isa0 820 821# 822# Options for `isa': 823# 824# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A 825# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 826# This option breaks suspend/resume on some portables. 827# 828# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A 829# interrupt controller. This saves about 0.7-1.25 usec for each interrupt. 830# Automatic EOI is documented not to work for for the slave with the 831# original i8259A, but it works for some clones and some integrated 832# versions. 833# 834# MAXMEM specifies the amount of RAM on the machine; if this is not 835# specified, FreeBSD will first read the amount of memory from the CMOS 836# RAM, so the amount of memory will initially be limited to 64MB or 16MB 837# depending on the BIOS. If the BIOS reports 64MB, a memory probe will 838# then attempt to detect the installed amount of RAM. If this probe 839# fails to detect >64MB RAM you will have to use the MAXMEM option. 840# The amount is in kilobytes, so for a machine with 128MB of RAM, it would 841# be 131072 (128 * 1024). 842# 843# TUNE_1542 enables the automatic ISA bus speed selection for the 844# Adaptec 1542 boards. Does not work for all boards, use it with caution. 845# 846# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to 847# reset the CPU for reboot. This is needed on some systems with broken 848# keyboard controllers. 849# 850# PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum 851 852options "AUTO_EOI_1" 853#options "AUTO_EOI_2" 854options "MAXMEM=(128*1024)" 855options "TUNE_1542" 856#options BROKEN_KEYBOARD_RESET 857#options PAS_JOYSTICK_ENABLE 858 859# Enable support for the kernel PLL to use an external PPS signal, 860# under supervision of [x]ntpd(8) 861# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp 862 863options PPS_SYNC 864 865# If you see the "calcru: negative time of %ld usec for pid %d (%s)\n" 866# message you probably have some broken sw/hw which disables interrupts 867# for too long. You can make the system more resistant to this by 868# choosing a high value for NTIMECOUNTER. The default is 5, there 869# is no upper limit but more than a couple of hundred are not productive. 870# A better strategy may be to sysctl -w kern.timecounter.method=1 871 872options "NTIMECOUNTER=20" 873 874# Enable PnP support in the kernel. This allows you to automaticly 875# attach to PnP cards for drivers that support it and allows you to 876# configure cards from USERCONFIG. See pnp(4) for more info. 877controller pnp0 878 879# The keyboard controller; it controlls the keyboard and the PS/2 mouse. 880controller atkbdc0 at isa? port IO_KBD tty 881 882# The AT keyboard 883device atkbd0 at isa? tty irq 1 884 885# Options for atkbd: 886options ATKBD_DFLT_KEYMAP # specify the built-in keymap 887makeoptions ATKBD_DFLT_KEYMAP="jp.106" 888 889# These options are valid for other keyboard drivers as well. 890options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap 891options KBD_INSTALL_CDEV # install a CDEV entry in /dev 892 893# `flags' for atkbd: 894# 0x01 Force detection of keyboard, else we always assume a keyboard 895# 0x02 Don't reset keyboard, useful for some newer ThinkPads 896# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads 897 898# PS/2 mouse 899device psm0 at isa? tty irq 12 900 901# Options for psm: 902options PSM_HOOKAPM #hook the APM resume event, useful 903 #for some laptops 904options PSM_RESETAFTERSUSPEND #reset the device at the resume event 905 906# The video card driver. 907device vga0 at isa? port ? conflicts 908 909# Options for vga: 910# Try the following option if the mouse pointer is not drawn correctly 911# or font does not seem to be loaded properly. May cause flicker on 912# some systems. 913options VGA_ALT_SEQACCESS 914 915# If you can dispense with some vga driver features, you may want to 916# use the following options to save some memory. 917options VGA_NO_FONT_LOADING # don't save/load font 918options VGA_NO_MODE_CHANGE # don't change video modes 919 920# Older video cards may require this option for proper operation. 921options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs 922 923# To include support for VESA video modes 924options VESA # needs VM86 defined too!! 925 926# Splash screen at start up! Screen savers require this too. 927pseudo-device splash 928 929# The pcvt console driver (vt220 compatible). 930device vt0 at isa? tty 931options XSERVER # support for running an X server. 932options FAT_CURSOR # start with block cursor 933# This PCVT option is for keyboards such as those used on IBM ThinkPad laptops 934options PCVT_SCANSET=2 # IBM keyboards are non-std 935# Other PCVT options are documented in pcvt(4). 936options "PCVT_24LINESDEF" 937options PCVT_CTRL_ALT_DEL 938options PCVT_EMU_MOUSE 939options PCVT_FREEBSD=211 940options PCVT_META_ESC 941options PCVT_NSCREENS=9 942options PCVT_PRETTYSCRNS 943options PCVT_SCREENSAVER 944options PCVT_USEKBDSEC 945options "PCVT_VT220KEYB" 946 947# The syscons console driver (sco color console compatible). 948device sc0 at isa? tty 949options MAXCONS=16 # number of virtual consoles 950options "STD8X16FONT" # Compile font in 951makeoptions "STD8X16FONT"="cp850" 952options SC_HISTORY_SIZE=200 # number of history buffer lines 953options SC_DISABLE_REBOOT # disable reboot key sequence 954 955# 956# `flags' for sc0: 957# 0x01 Use a 'visual' bell 958# 0x02 Use a 'blink' cursor 959# 0x04 Use a 'underline' cursor 960# 0x06 Use a 'blinking underline' (destructive) cursor 961# 0x40 Make the bell quiet if it is rung in the backgroud vty. 962 963# 964# The Numeric Processing eXtension driver. This should be configured if 965# your machine has a math co-processor, unless the coprocessor is very 966# buggy. If it is not configured then you *must* configure math emulation 967# (see above). If both npx0 and emulation are configured, then only npx0 968# is used (provided it works). 969device npx0 at isa? port IO_NPX iosiz 0x0 flags 0x0 irq 13 970 971# 972# `flags' for npx0: 973# 0x01 don't use the npx registers to optimize bcopy 974# 0x02 don't use the npx registers to optimize bzero 975# 0x04 don't use the npx registers to optimize copyin or copyout. 976# The npx registers are normally used to optimize copying and zeroing when 977# all of the following conditions are satisfied: 978# "I586_CPU" is an option 979# the cpu is an i586 (perhaps not a Pentium) 980# the probe for npx0 succeeds 981# INT 16 exception handling works. 982# Then copying and zeroing using the npx registers is normally 30-100% faster. 983# The flags can be used to control cases where it doesn't work or is slower. 984# Setting them at boot time using userconfig works right (the optimizations 985# are not used until later in the bootstrap when npx0 is attached). 986# 987 988# 989# `iosiz' for npx0: 990# This can be used instead of the MAXMEM option to set the memory size. If 991# it is nonzero, then it overrides both the MAXMEM option and the memory 992# size reported by the BIOS. Setting it at boot time using userconfig takes 993# effect on the next reboot after the change has been recorded in the kernel 994# binary (the size is used early in the boot before userconfig has a chance 995# to change it). 996# 997 998# 999# Optional ISA and EISA devices: 1000# 1001 1002# 1003# SCSI host adapters: `aha', `bt' 1004# 1005# adv: All Narrow SCSI bus AdvanSys controllers. 1006# adw: Second Generation AdvanSys controllers including the ADV940UW. 1007# aha: Adaptec 154x 1008# ahc: Adaptec 274x/284x/294x 1009# bt: Most Buslogic controllers 1010# 1011# Note that the order is important in order for Buslogic cards to be 1012# probed correctly. 1013# 1014 1015controller bt0 at isa? port "IO_BT0" cam irq ? 1016controller adv0 at isa? port ? cam irq ? 1017controller adw0 1018controller aha0 at isa? port ? cam irq ? 1019 1020# 1021# ATA and ATAPI devices 1022# This is work in progress, use at your own risk. 1023# It currently reuses the majors of wd.c and friends. 1024# It cannot co-exist with the old system in one kernel. 1025# You only need one "controller ata0" for it to find all 1026# PCI devices on modern machines. 1027#controller ata0 1028#device atadisk0 # ATA disk drives 1029#device atapicd0 # ATAPI CDROM drives 1030#device atapifd0 # ATAPI floppy drives 1031#device atapist0 # ATAPI tape drives 1032# 1033# If you need ISA only devices, this is the lines to add: 1034#controller ata1 at isa? port "IO_WD1" bio irq 14 1035#controller ata2 at isa? port "IO_WD2" bio irq 15 1036# 1037# All the controller lines can coexist, the driver will 1038# find out which ones are there. 1039 1040# 1041# ST-506, ESDI, and IDE hard disks: `wdc' and `wd' 1042# 1043# The flags fields are used to enable the multi-sector I/O and 1044# the 32BIT I/O modes. The flags may be used in either the controller 1045# definition or in the individual disk definitions. The controller 1046# definition is supported for the boot configuration stuff. 1047# 1048# Each drive has a 16 bit flags value defined: 1049# The low 8 bits are the maximum value for the multi-sector I/O, 1050# where 0xff defaults to the maximum that the drive can handle. 1051# The high bit of the 16 bit flags (0x8000) allows probing for 1052# 32 bit transfers. Bit 14 (0x4000) enables a hack to wake 1053# up powered-down laptop drives. Bit 13 (0x2000) allows 1054# probing for PCI IDE DMA controllers, such as Intel's PIIX 1055# south bridges. Bit 12 (0x1000) sets LBA mode instead of the 1056# default CHS mode for accessing the drive. See the wd.4 man page. 1057# 1058# The flags field for the drives can be specified in the controller 1059# specification with the low 16 bits for drive 0, and the high 16 bits 1060# for drive 1. 1061# e.g.: 1062#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 1063# 1064# specifies that drive 0 will be allowed to probe for 32 bit transfers and 1065# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be 1066# allowed to probe for 32 bit transfers, but will allow multi-sector 1067# transfers up to the maximum that the drive supports. 1068# 1069# If you are using a PCI controller that is not running in compatibility 1070# mode (for example, it is a 2nd IDE PCI interface), then use config line(s) 1071# such as: 1072# 1073#controller wdc2 at isa? port "0" bio irq ? flags 0xa0ffa0ff 1074#disk wd4 at wdc2 drive 0 1075#disk wd5 at wdc2 drive 1 1076# 1077#controller wdc3 at isa? port "0" bio irq ? flags 0xa0ffa0ff 1078#disk wd6 at wdc3 drive 0 1079#disk wd7 at wdc3 drive 1 1080# 1081# Note that the above config would be useful for a Promise card, when used 1082# on a MB that already has a PIIX controller. Note the bogus irq and port 1083# entries. These are automatically filled in by the IDE/PCI support. 1084# 1085 1086controller wdc0 at isa? port "IO_WD1" bio irq 14 1087disk wd0 at wdc0 drive 0 1088disk wd1 at wdc0 drive 1 1089controller wdc1 at isa? port "IO_WD2" bio irq 15 1090disk wd2 at wdc1 drive 0 1091disk wd3 at wdc1 drive 1 1092 1093# 1094# Options for `wdc': 1095# 1096# CMD640 enables serializing access to primary and secondary channel 1097# of the CMD640B IDE Chip. The serializing will only take place 1098# if this option is set *and* the chip is probed by the pci-system. 1099# 1100options "CMD640" #Enable work around for CMD640 h/w bug 1101# 1102# ATAPI enables the support for ATAPI-compatible IDE devices 1103# 1104options ATAPI #Enable ATAPI support for IDE bus 1105options ATAPI_STATIC #Don't do it as an LKM 1106 1107# 1108# This option allow you to override the default probe time for IDE 1109# devices, to get a faster probe. Setting this below 10000 violate 1110# the IDE specs, but may still work for you (it will work for most 1111# people). 1112# 1113options IDE_DELAY=8000 # Be optimistic about Joe IDE device 1114 1115# IDE CD-ROM & CD-R/RW driver - requires wdc controller and ATAPI option 1116device wcd0 1117 1118# IDE floppy driver - requires wdc controller and ATAPI option 1119device wfd0 1120 1121# IDE tape driver - requires wdc controller and ATAPI option 1122device wst0 1123 1124 1125# 1126# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft' 1127# 1128controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 1129# 1130# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you 1131# gotta turn it actually on by setting the variable fd_debug with DDB, 1132# however. 1133options FDC_DEBUG 1134# FDC_YE enables support for the floppies used on the Libretto. This is a 1135# pcmcia floppy. You will also need to add 1136#card "Y-E DATA" "External FDD" 1137# config 0x4 "fdc0" 10 1138# to your pccard.conf file. 1139options FDC_YE 1140# This option is undocumented on purpose. 1141options FDC_PRINT_BOGUS_CHIPTYPE 1142# 1143# Activate this line instead of the fdc0 line above if you happen to 1144# have an Insight floppy tape. Probing them proved to be dangerous 1145# for people with floppy disks only, so it's "hidden" behind a flag: 1146#controller fdc0 at isa? port "IO_FD1" bio flags 1 irq 6 drq 2 1147 1148disk fd0 at fdc0 drive 0 1149disk fd1 at fdc0 drive 1 1150 1151# 1152# Other standard PC hardware: `mse', `sio', etc. 1153# 1154# mse: Logitech and ATI InPort bus mouse ports 1155# sio: serial ports (see sio(4)) 1156 1157device mse0 at isa? port 0x23c tty irq 5 1158 1159device sio0 at isa? port "IO_COM1" tty flags 0x10 irq 4 1160 1161# 1162# `flags' for serial drivers that support consoles (only for sio now): 1163# 0x10 enable console support for this unit. The other console flags 1164# are ignored unless this is set. Enabling console support does 1165# not make the unit the preferred console - boot with -h or set 1166# the 0x20 flag for that. Currently, at most one unit can have 1167# console support; the first one (in config file order) with 1168# this flag set is preferred. Setting this flag for sio0 gives 1169# the old behaviour. 1170# 0x20 force this unit to be the console (unless there is another 1171# higher priority console). This replaces the COMCONSOLE option. 1172# 0x40 reserve this unit for low level console operations. Do not 1173# access the device in any normal way. 1174# 1175# PnP `flags' (set via userconfig using pnp x flags y) 1176# 0x1 disable probing of this device. Used to prevent your modem 1177# from being attached as a PnP modem. 1178# 1179 1180# Options for serial drivers that support consoles (only for sio now): 1181options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to 1182 #DDB, if available. 1183options CONSPEED=9600 #default speed for serial console (default 9600) 1184 1185# Options for sio: 1186options COM_ESP #code for Hayes ESP 1187options COM_MULTIPORT #code for some cards with shared IRQs 1188options "EXTRA_SIO=2" #number of extra sio ports to allocate 1189 1190# Other flags for sio that aren't documented in the man page. 1191# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for 1192# ST16650A-compatible UARTs. 1193 1194# 1195# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc' 1196# 1197# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp) 1198# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters 1199# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing) 1200# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503 1201# el: 3Com 3C501 (slow!) 1202# ep: 3Com 3C509 (buggy) 1203# ex: Intel EtherExpress Pro/10 and other i82595-based adapters 1204# fe: Fujitsu MB86960A/MB86965A Ethernet 1205# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress 1206# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100, 1207# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422) 1208# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960) 1209# rdp: RealTek RTL 8002-based pocket ethernet adapters 1210# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp) 1211# wl: Lucent Wavelan (ISA card only). 1212# ze: IBM/National Semiconductor PCMCIA ethernet controller. 1213# zp: 3Com PCMCIA Etherlink III (It does not require shared memory for 1214# send/receive operation, but it needs 'iomem' to read/write the 1215# attribute memory) 1216# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133 1217# (no options needed) 1218# 1219device ar0 at isa? port 0x300 net irq 10 iomem 0xd0000 1220device cs0 at isa? port 0x300 net irq ? 1221device cx0 at isa? port 0x240 net irq 15 drq 7 1222device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 1223device el0 at isa? port 0x300 net irq 9 1224device ep0 at isa? port 0x300 net irq 10 1225device ex0 at isa? port? net irq? 1226device fe0 at isa? port 0x300 net irq ? 1227device ie0 at isa? port 0x300 net irq 5 iomem 0xd0000 1228device ie1 at isa? port 0x360 net irq 7 iomem 0xd0000 1229device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 1230device lnc0 at isa? port 0x280 net irq 10 drq 0 1231device rdp0 at isa? port 0x378 net irq 7 flags 2 1232device sr0 at isa? port 0x300 net irq 5 iomem 0xd0000 1233options WLCACHE # enables the signal-strength cache 1234options WLDEBUG # enables verbose debugging output 1235device wl0 at isa? port 0x300 net irq ? 1236# We can (bogusly) include both the dedicated PCCARD drivers and the generic 1237# support when COMPILING_LINT. 1238device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 1239device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 1240 1241device oltr0 at isa? 1242 1243# 1244# ATM related options 1245# 1246# The `en' device provides support for Efficient Networks (ENI) 1247# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0). 1248# 1249# atm pseudo-device provides generic atm functions and is required for 1250# atm devices. 1251# NATM enables the netnatm protocol family that can be used to 1252# bypass TCP/IP. 1253# 1254# the current driver supports only PVC operations (no atm-arp, no multicast). 1255# for more details, please read the original documents at 1256# http://www.ccrc.wustl.edu/pub/chuck/bsdatm/wucs.html 1257# 1258pseudo-device atm 1259device en0 1260device en1 1261options NATM #native ATM 1262 1263# 1264# Audio drivers: `snd', `sb', `pas', `gus', `pca' 1265# 1266# snd: Voxware sound support code 1267# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum 1268# sbxvi: SoundBlaster 16 1269# sbmidi: SoundBlaster 16 MIDI interface 1270# pas: ProAudioSpectrum PCM and MIDI 1271# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX 1272# gusxvi: Gravis Ultrasound 16-bit PCM (do not use) 1273# mss: Microsoft Sound System 1274# css: Crystal Sound System (CSS 423x PnP) 1275# sscape: Ensoniq Soundscape MIDI interface 1276# sscape_mss: Ensoniq Soundscape PCM (requires sscape) 1277# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum 1278# uart: stand-alone 6850 UART for MIDI 1279# mpu: Roland MPU-401 stand-alone card 1280# 1281# Beware! The addresses specified below are also hard-coded in 1282# i386/isa/sound/sound_config.h. If you change the values here, you 1283# must also change the values in the include file. 1284# 1285# pcm: PCM audio through various sound cards. 1286# 1287# This has support for a large number of new audio cards, based on 1288# CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP. 1289# For more information about this driver and supported cards, 1290# see the pcm.4 man page and /sys/i386/isa/snd/CARDS. 1291# 1292# The flags of the device tells the device a bit more info about the 1293# device that normally is obtained through the PnP interface. 1294# bit 2..0 secondary DMA channel; 1295# bit 4 set if the board uses two dma channels; 1296# bit 15..8 board type, overrides autodetection; leave it 1297# zero if don't know what to put in (and you don't, 1298# since this is unsupported at the moment...). 1299# 1300# This driver will use the new PnP code if it's available. 1301# 1302# pca: PCM audio through your PC speaker 1303# 1304# If you have a GUS-MAX card and want to use the CS4231 codec on the 1305# card the drqs for the gus max must be 8 bit (1, 2, or 3). 1306# 1307# If you would like to use the full duplex option on the gus, then define 1308# flags to be the ``read dma channel''. 1309# 1310# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset 1311# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset 1312# options EXCLUDE_SBPRO #PAS-16 1313# options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line. 1314# PAS16: The order of the pas0/sb0/opl0 is important since the 1315# sb emulation is enabled in the pas-16 attach. 1316# 1317# To overide the GUS defaults use: 1318# options GUS_DMA2 1319# options GUS_DMA 1320# options GUS_IRQ 1321# 1322# The i386/isa/sound/sound.doc has more information. 1323 1324# Controls all "VOXWARE" driver sound devices. See Luigi's driver 1325# below for an alternate which may work better for some cards. 1326# 1327controller snd0 1328device pas0 at isa? port 0x388 irq 10 drq 6 1329device sb0 at isa? port 0x220 irq 5 drq 1 1330device sbxvi0 at isa? drq 5 1331device sbmidi0 at isa? port 0x330 1332device awe0 at isa? port 0x620 1333device gus0 at isa? port 0x220 irq 12 drq 1 1334#device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3 1335device mss0 at isa? port 0x530 irq 10 drq 1 1336device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 1337device sscape0 at isa? port 0x330 irq 9 drq 0 1338device trix0 at isa? port 0x330 irq 6 drq 0 1339device sscape_mss0 at isa? port 0x534 irq 5 drq 1 1340device opl0 at isa? port 0x388 1341device mpu0 at isa? port 0x330 irq 6 drq 0 1342device uart0 at isa? port 0x330 irq 5 1343 1344# Luigi's snd code (use INSTEAD of snd0 and all VOXWARE drivers!). 1345# You may also wish to enable the pnp controller with this, for pnp 1346# sound cards. 1347# 1348#device pcm0 at isa? port ? tty irq 10 drq 1 flags 0x0 1349 1350# Not controlled by `snd' 1351device pca0 at isa? port "IO_TIMER1" tty 1352 1353# 1354# Miscellaneous hardware: 1355# 1356# mcd: Mitsumi CD-ROM 1357# scd: Sony CD-ROM 1358# matcd: Matsushita/Panasonic CD-ROM 1359# wt: Wangtek and Archive QIC-02/QIC-36 tape drives 1360# ctx: Cortex-I frame grabber 1361# apm: Laptop Advanced Power Management (experimental) 1362# spigot: The Creative Labs Video Spigot video-acquisition board 1363# meteor: Matrox Meteor video capture board 1364# bktr: Brooktree bt848/848a/849/878/879 family video capture and TV Tuner board 1365# cy: Cyclades serial driver 1366# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!) 1367# dgm: Digiboard PC/Xem driver 1368# gp: National Instruments AT-GPIB and AT-GPIB/TNT board 1369# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey 1370# gsc: Genius GS-4500 hand scanner. 1371# joy: joystick 1372# labpc: National Instrument's Lab-PC and Lab-PC+ 1373# rc: RISCom/8 multiport card 1374# rp: Comtrol Rocketport(ISA) - single card 1375# tw: TW-523 power line interface for use with X-10 home control products 1376# si: Specialix SI/XIO 4-32 port terminal multiplexor 1377# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based) 1378# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent) 1379 1380# Notes on APM 1381# The flags takes the following meaning for apm0: 1382# 0x0020 Statclock is broken. 1383# 0x0011 Limit APM protocol to 1.1 or 1.0 1384# 0x0010 Limit APM protocol to 1.0 1385# If apm is omitted, some systems require sysctl -w kern.timcounter.method=1 1386# for correct timekeeping. 1387 1388# Notes on the spigot: 1389# The video spigot is at 0xad6. This port address can not be changed. 1390# The irq values may only be 10, 11, or 15 1391# I/O memory is an 8kb region. Possible values are: 1392# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff 1393# The start address must be on an even boundary. 1394# Add the following option if you want to allow non-root users to be able 1395# to access the spigot. This option is not secure because it allows users 1396# direct access to the I/O page. 1397# options SPIGOT_UNSECURE 1398 1399# Notes on the Comtrol Rocketport driver: 1400# 1401# The exact values used for rp0 depend on how many boards you have 1402# in the system. The manufacturer's sample configs are listed as: 1403# 1404# Comtrol Rocketport ISA single card 1405# device rp0 at isa? port 0x280 tty 1406# 1407# If instead you have two ISA cards, one installed at 0x100 and the 1408# second installed at 0x180, then you should add the following to 1409# your kernel configuration file: 1410# 1411# device rp0 at isa? port 0x100 tty 1412# device rp1 at isa? port 0x180 tty 1413# 1414# For 4 ISA cards, it might be something like this: 1415# 1416# device rp0 at isa? port 0x180 tty 1417# device rp1 at isa? port 0x100 tty 1418# device rp2 at isa? port 0x340 tty 1419# device rp3 at isa? port 0x240 tty 1420# 1421# And for PCI cards, you only need say: 1422# 1423# device rp0 1424# device rp1 1425# ... 1426# Note: Make sure that any Rocketport PCI devices are specified BEFORE the 1427# ISA Rocketport devices. 1428 1429# Notes on the Digiboard driver: 1430# 1431# The following flag values have special meanings: 1432# 0x01 - alternate layout of pins (dgb & dgm) 1433# 0x02 - use the windowed PC/Xe in 64K mode (dgb only) 1434 1435# Notes on the Specialix SI/XIO driver: 1436# **This is NOT a Specialix supported Driver!** 1437# The host card is memory, not IO mapped. 1438# The Rev 1 host cards use a 64K chunk, on a 32K boundary. 1439# The Rev 2 host cards use a 32K chunk, on a 32K boundary. 1440# The cards can use an IRQ of 11, 12 or 15. 1441 1442# Notes on the Stallion stl and stli drivers: 1443# See src/i386/isa/README.stl for complete instructions. 1444# This is version 0.0.5alpha, unsupported by Stallion. 1445# The stl driver has a secondary IO port hard coded at 0x280. You need 1446# to change src/i386/isa/stallion.c if you reconfigure this on the boards. 1447# The "flags" and "iosiz" settings on the stli driver depend on the board: 1448# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000 1449# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000 1450# EasyConnection 8/64 MCA: flags 25 iosiz 0x1000 1451# ONboard ISA: flags 4 iosiz 0x10000 1452# ONboard EISA: flags 7 iosiz 0x10000 1453# ONboard MCA: flags 3 iosiz 0x10000 1454# Brumby: flags 2 iosiz 0x4000 1455# Stallion: flags 1 iosiz 0x10000 1456 1457device mcd0 at isa? port 0x300 bio irq 10 1458# for the Sony CDU31/33A CDROM 1459device scd0 at isa? port 0x230 bio 1460# for the SoundBlaster 16 multicd - up to 4 devices 1461controller matcd0 at isa? port 0x230 bio 1462device wt0 at isa? port 0x300 bio irq 5 drq 1 1463device ctx0 at isa? port 0x230 iomem 0xd0000 1464device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000 1465device apm0 at isa? 1466device gp0 at isa? port 0x2c0 tty 1467device gsc0 at isa? port "IO_GSC1" tty drq 3 1468device joy0 at isa? port IO_GAME 1469device cy0 at isa? tty irq 10 iomem 0xd4000 iosiz 0x2000 1470options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared 1471device dgb0 at isa? port 0x220 iomem 0xfc000 iosiz ? tty 1472options "NDGBPORTS=16" # Defaults to 16*NDGB 1473device dgm0 at isa? port 0x104 iomem 0xd0000 iosiz ? tty 1474device labpc0 at isa? port 0x260 tty irq 5 1475device rc0 at isa? port 0x220 tty irq 12 1476device rp0 at isa? port 0x280 tty 1477# the port and irq for tw0 are fictitious 1478device tw0 at isa? port 0x380 tty irq 11 1479device si0 at isa? iomem 0xd0000 tty irq 12 1480device asc0 at isa? port "IO_ASC1" tty drq 3 irq 10 1481device stl0 at isa? port 0x2a0 tty irq 10 1482device stli0 at isa? port 0x2a0 tty iomem 0xcc000 flags 23 iosiz 0x1000 1483# You are unlikely to have the hardware for loran0 <phk@FreeBSD.org> 1484device loran0 at isa? port ? tty irq 5 1485# HOT1 Xilinx 6200 card (www.vcc.com) 1486device xrpu0 1487 1488# 1489# EISA devices: 1490# 1491# The EISA bus device is eisa0. It provides auto-detection and 1492# configuration support for all devices on the EISA bus. 1493# 1494# The `ahb' device provides support for the Adaptec 174X adapter. 1495# 1496# The `ahc' device provides support for the Adaptec 274X and 284X 1497# adapters. The 284X, although a VLB card responds to EISA probes. 1498# 1499# fea: DEC DEFEA EISA FDDI adapter 1500# 1501controller eisa0 1502controller ahb0 1503controller ahc0 1504device fea0 1505 1506# The aic7xxx driver will attempt to use memory mapped I/O for all PCI 1507# controllers that have it configured only if this option is set. Unfortunately, 1508# this doesn't work on some motherboards, which prevents it from being the 1509# default. 1510options AHC_ALLOW_MEMIO 1511 1512# By default, only 10 EISA slots are probed, since the slot numbers 1513# above clash with the configuration address space of the PCI subsystem, 1514# and the EISA probe is not very smart about this. This is sufficient 1515# for most machines, but in particular the HP NetServer LC series comes 1516# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11, 1517# thus you need to bump this figure to 12 for them. 1518options "EISA_SLOTS=12" 1519 1520# 1521# PCI devices & PCI options: 1522# 1523# The main PCI bus device is `pci'. It provides auto-detection and 1524# configuration support for all devices on the PCI bus, using either 1525# configuration mode defined in the PCI specification. 1526# 1527# The `ahc' device provides support for the Adaptec 29/3940(U)(W) 1528# and motherboard based AIC7870/AIC7880 adapters. 1529# 1530# The `ncr' device provides support for the NCR 53C810 and 53C825 1531# self-contained SCSI host adapters. 1532# 1533# The `isp' device provides support for the Qlogic ISP 1020, 1040 1534# nd 1040B PCI SCSI host adapters, as well as the Qlogic ISP 2100 1535# FC/AL Host Adapter. 1536# 1537# The `ax' device provides support for PCI fast ethernet adapters 1538# based on the ASIX Electronics AX88140A chip, including the Alfa 1539# Inc. GFC2204. 1540# 1541# The `de' device provides support for the Digital Equipment DC21040 1542# self-contained Ethernet adapter. 1543# 1544# The `fxp' device provides support for the Intel EtherExpress Pro/100B 1545# PCI Fast Ethernet adapters. 1546# 1547# The `mx' device provides support for various fast ethernet adapters 1548# based on the Macronix 98713, 987615 ans 98725 series chips. 1549# 1550# The `pn' device provides support for various fast ethernet adapters 1551# based on the Lite-On 82c168 and 82c169 PNIC chips, including the 1552# LinkSys LNE100TX, the NetGear FA310TX rev. D1 and the Matrox 1553# FastNIC 10/100. 1554# 1555# The 'rl' device provides support for PCI fast ethernet adapters based 1556# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults 1557# to useing programmed I/O to do register accesses because memory mapped 1558# mode seems to cause severe lockups on SMP hardware. This driver also 1559# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called 1560# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek 1561# workalike. 1562#
|